PAPER SHREDDER
Personal Series
MODELS
CC4-2
PRODUCT USAGE GUIDE
CC4-2
Sheet capacity*:
Shred type:
5
Confetti
Shred size:
5/32" x 2"
Entry width:
9-1/2"
Recommended use:
Maximum running time:
10-20 shredding passes per day
5-7 min. on/15 minutes off
*Sheet capacity measured with 20 lb., 8-1/2" x 11" paper with the shredder operating at rated voltage.
Different paper weights, humidity, and electrical currents will affect capacity.
PLEASE READ AND SAVE THIS MANUAL WITH YOUR ORIGINAL RECEIPT
Customer Service: 1-800-955-0959
Cool-Down Cycle
OPERATION
This shredder is protected with a special safety feature
which prevents the motor from overheating with exten-
sive use. When shredding is attempted beyond the
machine's maximum running time, the shredder
will automatically shut off its motor until it has
cooled to an acceptable operating level. This is nor-
mal and the shredder will return to operation after the
cool-down or "off" period. See "Product Usage Guide"
on front panel for maximum running time and related
cooling "off" time.
This product features an auto-start
sensor. This sensor will turn on the cut-
ting blades whenever anything is inserted into the
paper entry (while the power switch is in the AUTO
position). For the safety of pets and children, we rec-
ommend always moving the power switch to OFF and
unplugging whenever the shredder is unattended or
not in use.
1. Assemble shredder (see "ASSEMBLY").
2. Remove any paper clips or other foreign objects
(except staples) from paper. If folding paper to fit
paper entry, adjust sheet capacity appropriately.
Clearing a Jam
If the shredder sheet capacity is exceeded or paper is
not put in straight, a jam may result. See "Product
Usage Guide" on front panel for maximum sheet
capacity for your shredder.
Do not attempt to shred paper clips or
other hard materials (except staples)
To clear a jam:
with this machine. Extensive use of paper clips or other
hard materials will result in damage to the cutting sys-
tem and will void the manufacturer's warranty.
3. Be sure power switch is in OFF (O) position. Plug
shredder into proper power supply outlet.
1. Move the power switch to the REVERSE (R) posi-
tion. (NOTE: If waste basket is full, empty it before
clearing jam.) The shredder will reverse the paper
to clear the jam.
4. Move power switch to AUTO (I) position. To clear
the cutting blades, the shredder will "run" for about
1 second immediately after switching to AUTO (I).
When the unit is turned on and in standby mode,
the shredder is ready to be fed paper through the
paper entry. (See "TROUBLESHOOTING" if red
LED is lit.)
2. If the shredder jams in reverse, move the power
switch to AUTO (I) and allow to run for about five
seconds. If jam does not clear, move power switch
to REVERSE (R) again and allow to run for about
five seconds. Repeat this procedure until the jam is
cleared. If necessary, use care to grasp the paper
carefully and pull out to clear the jam.
3. Once the jam is cleared, move the power switch to
AUTO (I) for continued shredding or OFF (O) if
shredding is complete.
NEVER insert hands or fingers into
paper entry as serious personal injury
may result.
Do not exceed recommended sheet
capacity (see "Product Usage Guide"
on front cover of this manual).
5. Slide paper straight into paper entry until the shred-
der automatically begins shredding.
MAINTENANCE
Confetti cut shredders require regular (monthly) oiling of
the cutting blades to maintain proper operation. Failure to
oil the blades regularly could result in reduced sheet
capacity performance, excessive noise during operation,
paper jams and possibly shredder failure.
The shredder automatically stops a few seconds
after shredding is complete.
Continue shredding as desired to a MAXIMUM
shredding time of 5-7 minutes. At this time, the
machine MUST be allowed to "cool down" for a
MINIMUM of 15 minutes. (See "Cool-Down
Cycle" for more information.)
If the shredder jams or shuts off before the maxi-
mum shredding time, see "Clearing a Jam" section
for further instructions.
We recommend using only Powershred Lubricant
#35250 (available by contacting Fellowes) or a veg-
etable-based oil (such as corn or canola) in a non-
aerosol container with an extension nozzle.
Never use flammable synthetic oil,
petroleum- based, or aerosol lubri-
cants to oil the cutting blades. Some agents may com-
bust, causing serious injury.
To oil the cutting blades:
1. From the top of the shredder, squeeze the recom-
mended lubricant across the full width of the
blades.
2. Move the power switch to AUTO (I) position and
allow the blades to run at least 3 seconds.
3. Move the power switch to REVERSE (R) position
and allow it to run for at least 3 seconds.
4. Repeat steps 2-3 above at least 3 times.
6. Move power switch to OFF (O) position when
shredding is complete.
7. Unplug power cord from outlet whenever shredder
is unattended or not in use.
8. Check basket to see if it is full. If full, remove shred-
der head and empty basket contents. Replace
shredder head onto basket.
TROUBLESHOOTING
LIMITED WARRANTY
Shredder will not
Fellowes warrants all the cutting cylinders of the
machine to be free of defects in material and
workmanship for 3 years from the date of
purchase by the original consumer. Fellowes
warrants all other parts of the machine to be free
of defects in material and workmanship for 1 year
from the date of purchase by the original con-
sumer. If any part is found to be defective during
the warrant period, your sole and exclusive
remedy will be repair or replacement, at FellowesÕ
option and expense, of the defective part.
This warranty does not apply in cases of abuse,
mishandling or unauthorized repair. ANY
IMPLIED WARRANTY, INCLUDING THAT OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, IS HEREBY LIMITED
IN DURATION TO THE APPROPRIATE
WARRANTY PERIOD SET FORTH ABOVE.
In no event shall Fellowes be liable for any
consequential or incidental damages attributable
to this product. This warranty gives you specific
legal rights. You may have other legal rights that
vary from state to state.
For more detail or to obtain service under this
warranty, please contact Fellowes Customer
Service at 1-800-955-0959, Monday through
Friday, 8 AM - 5 PM (Central Standard Time).
For specific instructions on obtaining service
under this warranty on machines purchased out-
side the USA, contact the appropriate location
listed in the Contact for Service section of this
instruction manual.
a. Shredder is not plugged in.
operate.
b. Power switch is in the OFF (O)
position. Move switch to AUTO (I)
position.
c. Shredder is jammed. See
"Clearing a Jam" section.
d. Shredder has exceeded the maxi-
mum run time and requires a
"cool-down" time. See "Product
Usage Guide" on front panel.
e. Shredder is not assembled prop-
erly. See "Assembly."
Shredder makes a
loud squeaking or
rubbing noise.
a. Cutting blades need to be oiled
REGULARLY. See "MAINTE-
NANCE" section.
Shredder suddenly
stops while
shredding.
a. Shredder has exceeded the maxi-
mum run time and requires a
"cool-down" time. See "Product
Usage Guide" on front panel.
b. Shredder is jammed. See
"OPERATION - Clearing a Jam."
Shredder shreds
less than capacity.
a. Cutting blades need to be oiled
REGULARLY. See "MAINTE-
NANCE" section.
a. Shredder is not assembled prop-
erly. See "ASSEMBLY."
Red LED is lit.
Shredder operates
only in REVERSE.
a. A small piece of paper may be
blocking the auto-start sensor of
this shredder. Move the power
switch to the OFF (O) position and
unplug the shredder. Turn shred-
der over and use a toothpick
(from the underside of the unit)
to clear the paper blockage at the
auto-start sensor (center) location.
Shredder runs con-
tinuously when in
AUTO.
a. A small piece of paper may be
causing the auto-start feature to
run continuously. Move the power
switch to the OFF (O) position and
unplug the shredder. Use a
toothpick (from the top of the
unit) to clear the paper blockage
at the auto-start sensor (center)
location.
Warrantor: Fellowes Manufacturing Company.
a. This is normal. The shredder runs
a few seconds longer than the
paper in order to keep the cutters
clear of paper particles and reduce
the chances of a jam.
Shredder runs for a
few seconds after
the paper has
Customer Service 1-800-955-0959
cleared the cutters.
1789 Norwood Avenue ¥ Itasca, Illinois 60143-1095
630-893-1600
®
Australia
Benelux
Canada
France
Germany
Italy
Japan
Poland
United Kingdom
Tullamarine, Vic Vianen, NL
Markham, Ont.
Rennes, I-V
Garbsen, Han.
Camerano, AN
Tokyo
Warsaw
Doncaster, S. Yorks.
© 2001 Fellowes Printed in China. Form No. 30117
|