Extron electronic Switch TLP VIM User Manual

User Guide  
TouchLink™  
TLP VIM  
TouchLink Video Input Module  
68-2055-01 Rev. A  
03 11  
 
FCC Class A Notice  
This equipment has been tested and found to comply with the limits for a Class A  
digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the  
following two conditions:  
1. This device may not cause harmful interference.  
2. This device must accept any interference received, including interference  
that may cause undesired operation.  
The Class A limits are designed to provide reasonable protection against harmful  
interference when the equipment is operated in a commercial environment. This  
equipment generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instruction manual, may cause harmful  
interference to radio communications. Operation of this equipment in a residential  
area is likely to cause harmful interference, in which case the user will be required  
to correct the interference at his own expense.  
NOTE: This unit was tested with shielded cables on the peripheral devices.  
Shielded cables must be used with the unit to ensure compliance  
with FCC emissions limits.  
For more information on safety guidelines, regulatory compliances,  
EMI/EMF compliance, accessibility, and related topics.  
Notational Conventions Used in this Guide  
TIP: A tip provides a suggestion to make setting up or working with  
the device easier.  
NOTE: A note draws attention to important information.  
CAUTION:  
WARNING:  
A caution warns of things or actions that might damage  
the equipment.  
A warning warns of things or actions that might cause  
injury, death, or other severe consequences.  
Copyright  
© 2011 Extron Electronics. All rights reserved.  
Trademarks  
All trademarks mentioned in this guide are the properties of their respective owners.  
 
 
Introduction  
This section gives an overview of the TLP VIM, TouchLink™ Video  
Input Module describing its operation and features including  
connection and operation with the Extron line of TouchLink panels.  
Topics that are covered include:  
z
z
About the TLP VIM  
Application Diagrams  
About the TLP VIM  
The TLP VIM is a twisted pair transmitter for composite or S-video  
with audio, designed exclusively for use with compatible Extron  
TouchLink touchpanels. The TLP VIM has a very specific application  
to these touchpanels and is not intended to be used in other  
applications.  
Compatible TLP touchpanel products have a single video input  
supporting AV signals via an MTP receiver built into the touchpanel.  
For installations where the video source is within 100 feet of the  
touchpanel, the TLP VIP provides a cost effective solution to transmit  
video and audio to the touchpanel.  
Due to the limited range, the TLP VIM does not require skew or gain  
adjustments.  
TLP VIM • Introduction  
1
 
Video/Audio  
Extron  
TLP VIM  
P
O
W
E
R
A
U
D
IO  
+
-
M
TP  
V
ID  
E
OUTPU  
U  
O
+
-
T
TLP 1000TV  
Video/  
Audio  
PC or DVD  
Extron  
12 V Power  
Supply  
POWER  
AUDIO  
+
Extron  
TLP VIM  
-
MTP OUTPUT  
VIDEO  
+
-
Audio  
Video/Audio  
(100´ max)  
Video  
PC or DVD  
TLP 1000TV  
Figure 1. TLP VIM Application Diagrams  
2
TLP VIM • Introduction  
 
Installation and  
Operation  
This chapter shows how to install and operate the TLP VIM Video  
Input Module.  
Topics that are covered include:  
z
z
z
z
Installation Overview  
Mounting the TLP VIM  
Installation Overview  
To install and set up the TLP VIM, follow these steps:  
1. Turn all equipment off. Make sure the video sources (DSS,  
cable boxes, PC, laptop, or other devices), the TLP VIM, and the  
touchpanel are turned off and disconnected from power sources.  
2. Mount the TLP VIM, see "Mounting the TLP VIM", below.  
page 4.  
4. Connect power cords and turn on the devices, see "Operation" on  
Mounting the TLP VIM  
The TLP VIM includes hook and loop fasteners so that it can be  
securely mounted on or under a table or podium near to the  
touchpanel.  
Shut off all power to connected devices, then mount the TLP VIM as  
required.  
TLP VIM • Installation and Operation  
3
 
 
TLP VIM Front and Rear Panel Features  
Front  
TLP VIM  
a
b
Rear  
c
d
e
INPUT  
POWER  
12V  
VIDEO  
0.5A MAX  
AUDIO  
OUTPUT  
Figure 2. TLP VIM Front and Rear Panel  
Front panel LED ꢀ Single LED lights to indicate the TLP VIM is  
properly powered.  
a
b
DC power input ꢀ Single 2-pole, 3.5 mm, orange captive screw  
connector for connection of a 12 V power supply.  
Use only the included power supply or an Extron authorized  
power supply to power the TLP VIM.  
4
TLP VIM • Installation and Operation  
 
 
INPUT  
POWER  
12V  
VIDEO  
0.5A MAX  
AUDIO  
Smooth  
Ridges  
Captive  
Screw  
Connector  
A
A
OUTPUT  
SECTION A–A  
Tie Wrap  
Power Supply  
Output Cord  
DC Power Cord  
Captive Screw  
Connector  
3"  
16 (5 mm) Max.  
Ground  
+12 VDC  
External  
Power Supply  
(12 VDC, 1 A )  
AC Power Cord  
Figure 3. Power Supply Wiring  
CAUTION:  
Always use a power supply supplied or specified by Extron. Use  
of an unauthorized power supply voids all regulatory compliance  
certification and may cause damage to the supply and the  
TLP VIM.  
Extron power supplies are certified to UL/CSA 60950-1 and  
are classified as LPS (limited power source). Use of a non-LPS  
or unlisted power supply will void all regulatory compliance  
certification.  
Unless otherwise stated, the AC/DC adapters are not suitable for  
use in air handling spaces or in wall cavities. The power supply is  
to be located within the same vicinity as the Extron A/V processing  
equipment in an ordinary location, Pollution Degree 2, secured to  
the equipment rack within the dedicated closet, podium or desk.  
The installation must always be in accordance with the applicable  
provisions of National Electrical Code ANSI/NFPA 70, article 75, and  
the Canadian Electrical Code, part 1, section 16. The power supply  
shall not be permanently fixed to building structure or similar  
structure.  
Audio input ꢀ One 3-pole captive screw connector for inputting  
balanced or unbalanced audio. The audio input is mono only and  
either balanced or unbalanced.  
c
Tip  
Tip  
Ring  
Sleeve  
Sleeve  
Unbalanced Input  
Balanced Input  
Figure 4. Audio Input Connector Wiring  
TLP VIM • Installation and Operation  
 
5
Video input ꢀ Two female BNC connectors on pigtails used to  
input either S-video (yellow-chroma, white-luma) or composite  
video (white only).  
d
For composite input, connect the composite cable to the white  
video input cable.  
12V  
0.5A MAX  
AUD  
For S-video input  
connect the luma cable  
to the white video  
input and the chroma  
cable to the yellow  
video input.  
White: Luma or  
Composite  
Yellow: Chroma  
Figure 5. Video Inputs  
MTP output ꢀ One female RJ-45 connector to output the MTP A/V  
signal to the touchpanel.  
e
The TP cable connecting the TLP VIM output to the MTP input of  
the touchpanel is standard UTP or STP Cat 5 or better cable. The  
ends may be terminated using either TIA/EIA 568A or TIA/EIA 568B  
but both ends must use the same standard.  
Pins:  
MTP Signal  
Composite  
MTP Signal  
S-video  
T568A  
T568B  
12345678  
Pin Wire Color  
Wire Color  
1
2
3
4
5
6
7
8
White-green White-orange Reserved  
Chroma+  
Chroma–  
Mono audio+  
Luma+  
Green  
Orange  
Reserved  
Mono audio+  
Video+  
White-orange White-green  
Blue  
Blue  
White-blue  
White-blue  
Video–  
Luma–  
Orange  
Green  
Mono audio–  
Mono audio–  
Reserved  
Reserved  
White-brown White-brown Reserved  
Brown Brown Reserved  
Insert  
TP Wires  
NOTE: When using Enhanced Skew-Free™ A/V cable, use  
the TIA/EIA T568A standard only.  
CAUTION:  
The TLP VIM output uses higher voltages than a LAN. Inputting  
those voltages on a LAN communications port may damage the  
connection.  
Operation  
No setup or configuration is required. Once cabling is complete,  
apply power to the connected equipment and TLP VIM. The unit is  
ready for operation.  
6
TLP VIM • Installation and Operation  
 
 
Reference Information  
Included Parts  
Description  
Part Number  
TLP VIM  
60-1168-01  
12 VDC, 1 A power supply  
28-071-57LF  
10-703-11LF  
3-pole blue 3.5 mm male captive screw connector  
TLP VIM User Guide  
Optional Accessories  
Enhanced Skew-Free™ A/V UTP Cable  
Skew-Free UTP/3, 3 ft (90 cm)  
Part Number  
26-569-01  
Skew-Free UTP/6, 6 ft (1.8 m)  
26-569-02  
Skew-Free UTP/12, 12 ft (3.6 m)  
26-569-03  
Skew-Free UTP/1000, non-plenum, 1000 ft (300 m) 22-141-03  
Skew-Free UTP-P/1000, plenum, 1000 ft (300 m) 22-142-03  
TLP VIM • References  
 
7
Specifications  
Video  
Gain����������������������������������������������� Unity  
Differential phase error������������������� <1�0° at 3�58 MHz and 4�43 MHz  
Differential gain error ��������������������� <1�0% at 3�58 MHz and 4�43 MHz  
Video input  
Number/signal type ������������������������ 1 S-video or composite video  
Connectors ������������������������������������ 2 female BNC on pigtails  
Nominal level ��������������������������������� 1 Vp-p for Y of S-video and for  
composite video  
0�3 Vp-p for C of S-video  
Minimum/maximum levels�������������� 0�3 V to 1�5 Vp-p with no offset  
Impedance ������������������������������������� 75 ohms  
Return loss������������������������������������ <-30 dB, DC @ 10 MHz  
DC offset (max� allowable) ������������� 100 mV  
Video output  
Number/signal type ������������������������ 1 set of proprietary analog signals  
Connector�������������������������������������� 1 female RJ-45  
Nominal level ��������������������������������� 1 V p-p for Y of S-video and for  
composite video  
0�3 V p-p for C of S-video  
Minimum/maximum levels�������������� 0�3 V to 1�5 Vp-p  
Impedance ������������������������������������� 75 ohms  
Return loss������������������������������������ <-35 dB @ 5 MHz  
Sync  
Standards��������������������������������������� NTSC 3�58, NTSC 4�43, PAL, SECAM  
Audio  
Gain����������������������������������������������� 0 dB (unity)  
Frequency response����������������������� 20 Hz to 20 kHz, 0�25 dB  
THD + Noise����������������������������������� 0�03% @ 1 kHz, 0�3% @ 20 kHz at  
nominal level  
S/N������������������������������������������������� >90 dB, balanced at maximum output  
(unweighted)  
CMRR �������������������������������������������� >34 dB @ 20 Hz to 20 kHz  
8
TLP VIM • References  
 
Audio input  
Number/signal type ������������������������ 1 mono, balanced or unbalanced  
Connector�������������������������������������� (1) 3�5 mm captive screw connector,  
3 pole  
Impedance ������������������������������������� >10k ohms unbalanced, >20k ohms  
balanced, AC coupled  
Nominal level ��������������������������������� -10 dBV (0�32 Vrms)  
Maximum level������������������������������� >+2�4 dBu (balanced or unbalanced) at  
1%THD+N  
NOTE: 0 dBu = 0�775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu  
Audio output  
Number/signal type ������������������������ 1 set of proprietary analog signals  
Connector�������������������������������������� 1 female RJ-45  
Impedance ������������������������������������� 50 ohms unbalanced, 100 ohms  
balanced  
Maximum level (Hi-Z)���������������������� >+3�3 dBu, balanced or unbalanced at  
1%THD+N  
Maximum level (600 ohm)�������������� >+2�0 dBm, balanced or unbalanced at  
1%THD+N  
General  
Recommended cable type �������������� CAT5/5e/6 (shielded or unshielded)  
External power supply������������������� Input: 100 VAC to 240 VAC, 50-60 Hz,  
external power supply  
Output: 12 VDC, 1�0 A, regulated  
Power input requirements �������������� 12 VDC, 0�5 A max�  
Temperature/humidity �������������������� Storage: -40 to +158 °F (-40 to +70 °C)  
/ 10% to 90%, noncondensing  
Operating: +32 to +122 °F (0 to +50 °C)  
/ 10% to 90%, noncondensing  
Cooling����������������������������������������� Convection, no vents  
Mounting��������������������������������������� Tabletop  
Enclosure type�������������������������������� Plastic  
Enclosure dimensions ��������������������� 1�0" H x 2�4" W x 2�3" D  
(2�5 cm H x 6�1 cm W x 5�8 cm D)  
(Depth excludes pigtail connectors�)  
Product weight������������������������������� 0�2 lbs (0�1 kg)  
Shipping weight���������������������������� 1 lb (1 kg)  
Vibration��������������������������������������� ISTA 1A in carton (International Safe  
Transit Association)  
TLP VIM • References  
 
9
Regulatory compliance  
Safety������������������������������������� CE, c-UL, UL  
EMI/EMC ��������������������������������� CE, C-tick, FCC Class A, ICES, VCCI  
MTBF ��������������������������������������������� 30,000 hours  
Warranty��������������������������������������� 3 years parts and labor  
NOTE: All nominal levels are at 10%�  
10 TLP VIM • References  
 
Extron® Warranty  
Extron Electronics warrants this product against defects in materials and workmanship  
for a period of three years from the date of purchase. In the event of malfunction  
during the warranty period attributable directly to faulty workmanship and/or materials,  
Extron Electronics will, at its option, repair or replace said products or components, to  
whatever extent it shall deem necessary to restore said product to proper operating  
condition, provided that it is returned within the warranty period, with proof of  
purchase and description of malfunction to:  
USA, Canada, South America,  
and Central America:  
Extron Electronics  
1001 East Ball Road  
Anaheim, CA 92805  
U.S.A.  
Japan:  
Extron Electronics, Japan  
Kyodo Building, 16 Ichibancho  
Chiyoda-ku, Tokyo 102-0082  
Japan  
Europe, Africa, and the  
Middle East:  
Extron Europe  
Hanzeboulevard 10  
3825 PH Amersfoort  
The Netherlands  
China:  
Extron China  
686 Ronghua Road  
Songjiang District  
Shanghai 201611  
China  
Asia:  
Extron Asia  
Middle East:  
Extron Middle East  
135 Joo Seng Road, #04-01  
PM Industrial Bldg.  
Singapore 368363  
Singapore  
Dubai Airport Free Zone  
F12, PO Box 293666  
United Arab Emirates, Dubai  
This Limited Warranty does not apply if the fault has been caused by misuse, improper  
handling care, electrical or mechanical abuse, abnormal operating conditions, or if  
modifications were made to the product that were not authorized by Extron.  
NOTE: If a product is defective, please call Extron and ask for an application  
engineer to receive an RA (return authorization) number. This will begin  
the repair process.  
USA:  
Asia:  
(714) 491-1500  
65.6383.4400  
Europe: 31.33.453.4040  
Japan: 81.3.3511.7655  
Units must be returned insured, with shipping charges prepaid. If not insured, you  
assume the risk of loss or damage during shipment. Returned units must include the  
serial number and a description of the problem, as well as the name of the person to  
contact in case there are any questions.  
Extron Electronics makes no further warranties either expressed or implied with  
respect to the product and its quality, performance, merchantability, or fitness for  
any particular use. In no event will Extron Electronics be liable for direct, indirect,  
or consequential damages resulting from any defect in this product even if Extron  
Electronics has been advised of such damage.  
Please note that laws vary from state to state and country to country, and that some  
provisions of this warranty may not apply to you.  
 

Focal Car Speaker 27 V1 User Manual
Fostex Speaker PM SUBN User Manual
Fujitsu Scanner FI 6670(A) User Manual
Garmin Marine GPS System 620 User Manual
GE Answering Machine 10 02 Network User Manual
GE Cordless Telephone 28802 User Manual
GE Door 19230 User Manual
Gemini Car Stereo System CDX 1210 User Manual
GE Monogram Refrigerator ZISW B480DX User Manual
Gitzo Camcorder Accessories G1227G User Manual