Extron electronic Switch DVC 501 SD User Manual

Product Category  
DVC 501 SD • Setup Guide  
The Extron DVC 501 SD receives SD-SDI, HD-SDI, and 3G-SDI serial digital video signals and converts them to DVI-D and  
analog RGB or component video. It is compliant with SMPTE 259M, 292M, 424M, and ITU digital video standards. The RGB  
output can be set for RGBHV, RGBS, and RGsB. Bi-level or tri-level sync can be selected when the unit is set for component  
video output. The DVC 501 SD features extraction of embedded AES3 audio, RS-232 and USB serial control, and a buffered  
loop-through that delivers reshaped and restored multi-rate SDI signals.  
NOTE: For full installation, configuration, and operation details, see the DVC 501 SD User Guide, available at  
Rear Panel Features and Connections  
1
6
2
3
4
5
100-240V ~ 0.3A MAX  
INPUT  
OUTPUT  
AUDIO  
BUFFERED  
LOOP-THROUGH  
DVI-D  
3G / HD / SD-SDI  
RGB/R-Y,Y,B-Y  
L
R
RS-232  
7
50/60 Hz  
N/A  
Tx Rx  
AC power connector  
DVI-D output connector  
Audio output connector  
RS-232 connector  
a
b
c
d
e
f
g
3G/HD/SD-SDI input connector  
Buffered Loop-through connector  
RGB/YUV output connector  
Installation Steps  
1. Disconnect power from all equipment.  
2. (Optional) Mount the unit to a rack or furniture.  
3. Connect the video input. Connect an SD-SDI, HD-SDI, or 3G-SDI source to the 3G/HD/SD-SDI port of the BNC input  
connector (b in the rear panel illustration above).  
4. (Optional) Connect a monitor or recording device. Attach a monitor or video recording device to the Buffered  
Loop-through BNC connector (c).  
5.  
Connect the video output. Connect a display or other output device to the DVD-D digital video connector (d) or to  
the RGB/R-Y,Y,B-Y analog RGB (RGBHV, RGBS, and RGsB) or YUV component video connector (e).  
6. Connect a control device. Connect a host device, such as a computer or touchpanel control system to one or both of  
the following DVC ports to configure and control the DVC via Simple Instruction Set (SIS™) commands.  
_
z
RS-232 port (rear panel) — Connect a host device to the Tx, Rx, and (ground) pins of this 5-pole captive screw  
connector (g). The first and second pins of this connector are not used. The default protocol for this port is  
9600 baud, 1 stop bit, no parity, 8 data bits, and no flow control.  
z
Config port (front panel) — Connect a USB cable (USB A to USB mini B) between a USB port on your computer  
and this port (a on the front panel illustration on the next page).  
7. Connect the audio output. Connect an amplifier or other audio output device to the 5-pole captive screw audio  
connector (f on the rear panel illustration), as shown below.  
Tip  
Ring  
Sleeves  
Tip  
Tip  
Sleeves  
Tip  
Do not tin the wires!  
Ring  
Balanced Audio Output  
Unbalanced Audio Output  
CAUTION:  
For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect them to negative (–)  
contacts.  
8. Connect power to the DVC 501 SD by plugging a standard IEC power cord (provided) from a 100 to 240 VAC, 50-60 Hz  
power source into the power receptacle (a).  
1
 

Estate Range W10173755D User Manual
Euro Pro Blender EP585 User Manual
Euro Pro Vacuum Cleaner XSC410 User Manual
FEIN Power Tools Vacuum Cleaner 9 11 55 User Manual
Fisher Price Building Set R9107 User Manual
Fujitsu Laptop S 4572 User Manual
Garland Oven RBA 24 User Manual
GE Monogram Cooktop Halogen Radiant Cooktop User Manual
GE Washer WWA8810R User Manual
Gigabyte Portable Speaker GP S5500 User Manual