GPS Powered for Speed and Location Intelligence
ESCORT Inc.
5440 West Chester Road
West Chester OH 45069 USA
Custom-Installed System
800.543.1608
EscortRadar.com
©2008 ESCORT Inc.
Made in Canada
Features, specifications and prices subject to change without notice.
Model: PASSPORT 9500ci
R
A
D
A
R
A
N
D
L
A
S
E
R
D
E
F
E
N
S
E
S
Y
S
T
E
M
Owner’s Manual
Quick Reference Card
Table of Contents
Quick Reference Guide
Controls and Features
• Power
4-5
6-11
6
Preferences
12-16
12
• How to use Preferences
• Example of Preferences
• Overview of Preferences
• Details of Preferences
Technical Details
• Specifications
12
• Power-On Indication
• Volume Control
6
13
6
14-16
12-25
17
Remove card along perforations
• Mute/AutoMute
6-7
7
PASSPORT 9500ci Quick Reference Card
• Sensitivity
Press the VOL button
to go from one category
to the next
Press the BRT/CHG button
to change your setting
within a category
• Marking Locations
• Safety Camera Data
• Auto Learn / Auto Unlearn
• Locking Out False Alarms
• Audible Alerts
8
• Interpreting Alerts
• How Radar Works
• How “POP” Works
• How Laser Works
• How GPS Works
• How TotalShield™ Works
• How TrueLock Works
• How AutoLearn Works
• How Safety Radar Works
Service
18-19
20
PILOT Pilot HWY * Full word: Highway, AutoScan, etc.
(Power-on indication) Pilot H
9
Letter: H, A, ANX
Letter, with scanning dot
Vehicle voltage
Pilot H.>
Pilot V
9
21
Pilot SPD
Vehicle speed
GPS
GPS ON * GPS On
GPS OFF
GPS Off
aLrn ON * AutoLearn On
aLrn OFF
AutoLearn Off
9
21
AUTOLEARN
9
22
SPEED ALERT sAlrt ON * Speed Alert On
sAlrt OFF
Speed Alert Off
• Voice Announcements
• Display Brightness
• Signal Strength Meter
• ExpertMeter
10
10
10
11
22
METER Meter STD * Bar-graph Meter
Meter EXP
Meter SPC
Expert Meter
Spec Display
23
AUTOMUTE aMute ON * AutoMute On
aMute OFF
AutoMute Off
UNITS Units ENG * Units English
Units MET
Units Metric
VOICE Voice ON * Voice Alerts On
Voice OFF
Voice Alerts Off
23
24-25
26-33
26-27
28
BANDS Bands DFT * Factory Default Settings
Bands MOD
Factory Default Settings Modified
• Troubleshooting
• Service
Turn bands ON or OFF by
pressing the MUTE button
X
K
Ka
POP
SWS
ONor OFF(default is on)
ONor OFF(default is on)
ONor OFF(default is on)
ONor OFF(default is off)
ONor OFF(default is off)
• Warranty
29
• Registration
31-32
LSR RECVor SHFTor OFF
(default is RECV)
Mark DFT * Factory Default Settings
Mark MOD
Factory Default Settings Modified
MARKERS
rCam ONor OFF(default is on)
sCam ONor OFF(default is on)
Trap ONor OFF(default is on)
Othr ONor OFF(default is on)
* Factory Default Settings
2
3
Quick Reference Guide
Power Button
Mark Location Button (MRK)
Press and hold to manually turn the
9500ci on or off. If installed properly, the
system will turn on or off automatically
with the ignition.
The “MRK” button allows you to mark a
specific location and label it for future
reference. Once marked, the PASSPORT
9500ci will provide an alert before you
reach this area again. This can be
extremely useful when there are known
speed traps or safety cameras in a
particular location. Page 8
Control Module
Display Module
Sensitivity Button (SENS)
The “SENS” button selects the 9500ci’s
sensitivity. The choices are Highway (full
sensitivity), Auto (based on the speed of
the vehicle) and Auto No X, (same as Auto
but without X-band). In general, we
recommend Auto. Page 7
Display Brightness (BRT)
The “BRT” button selects your preferred
brightness level. The factory default
setting is Auto (automatic), which will
adjust the display brightness based on the
ambient light in the vehicle. See the
Preferences section for details.
Volume Button (VOL)
Press and hold the VOL button on the
controller to adjust the alert volume level.
The audio will ramp up to increase, down
to decrease, accompanied by a bar-graph
on the display.
To change the direction of the audio
ramping (down instead of up or vice
versa) simply release the VOL button
quickly press and hold it again to change
its direction.
Mute Button (Mute)
Briefly press this button to silence the
audio for a specific alert. (The audio will
alert you to the next encounter.) Pages 6-7
MatrixDisplay
The 9500ci’s alphanumeric display
consists of 280 individual LEDs, to provide
an intuitive ultra-bright display of signal
strength and text messages. The 9500ci’s
display will show Highway, Auto, or
AutoNoX as its power-on indication. If you
prefer, you can choose other power-on
indications. Pages 12-15
GPS Signal Indicator
The GPS icon indicates reception of GPS
satellite signals and will rotate when
a false alert is being rejected.
NOTE: Your preferred audio level
will be stored in memory, even after
the detector is turned off.
During an alert, the display will
indicate the radar or laser band, and a
precise bar-graph of signal strength.
Page 14
Note: In the Dark Mode the
display will not light during an alert.
4
5
Controls and Features
Power
Mute
4. Disengage “Laser Shifting”. To do this,
simply double-tap the mute button during
a laser alert once you’ve adjusted your
speed. This will put the Laser Shifters into
a “receive only” mode for approximately
(1) one minute. Once this time has passed,
the Shifters will automatically return to
the “shifting” mode.
NOTE: Shifters must be turned on
in Preferences. See Preferences
section for details.
5. Once the vehicle is under 25 mph,
press and hold to disable the Shifters for
an extended period of time. Once the
vehicle reaches 25 mph, the Shifters will
reset and return to Shift mode.
Radar Sensitivity
The 9500ci is typically wired to a
switched supply at the vehicle’s fuse box.
This allows the detector to turn on/off
with the ignition. If you prefer, the power
button can be used to manually turn the
9500ci on or off.
The MUTE button, located in the center of
the 9500ci’s controller, has several
functions:
1. Mute the audio during a single alert.
To do this, briefly press the MUTE button
during the alert. After that radar
encounter has passed, the Mute will
disengage, and the audio will return to
your preset level.
2. Lockout false alarms using TrueLock.
To do this, simply press the Mute button
(3) three consecutive times during the
false alert. The first time the audio will
mute as stated above. The second time the
mute button is pressed; the display will
read “Lockout?” To confirm and lockout
that signal, press the mute button a third
time.
NOTE: Visually scan the area to
ensure no real threat exists before
locking out any signals.
Once a signal has been locked out, the
satellite icon on the display will rotate,
giving you a visual indication that it is
detecting that signal, but no alert will be
given.
3. Unlock a signal. To do this, simply
press and hold the Mute button while the
icon is rotating. An “Unlock” message will
be displayed. Press the mute button again
to confirm and unlock that signal.
The “SENS” button selects the 9500ci’s
radar sensitivity. The choices are
“Highway”, “Auto” or “Auto No X”. In
general, we recommend “Auto” for every
day driving.
Highway (Highway Mode)
In this setting, the 9500ci will detect all
radar signals on all bands at maximum
range.
Power-On Indication
Once your 9500ci’s is installed, the system
will turn on with the ignition. Once the
start-up sequence is complete, the display
will show “Highway”, “Auto” or “Auto NoX”
to indicate which sensitivity mode it is in.
If you prefer, you can select alternate
power-on displays. See the Preferences
section for details.
Auto (AutoMode)
In this setting the 9500ci will
automatically adjust its radar sensitivity
based on the speed of your vehicle. At
slower speeds, (<25mph) X and K-band
sensitivity is reduced to minimize alerts
caused by automatic door openers, etc.
At higher speeds, (>45 mph) X and K-
band sensitivity is increased to maximum.
Note: Full sensitivity is
AutoMute
Volume Control
Your 9500ci has our patented AutoMute
feature. After the 9500ci alerts you to a
radar encounter at the volume you have
selected, the AutoMute feature will
automatically reduce the volume to a
lower level. This keeps you informed
without the annoyance of a continuous
full-volume alert.
Press and hold the VOL button on the
controller to adjust the alert volume level.
The audio will ramp up and down,
accompanied by a bar-graph on the display.
Once your desired level is reached, simply
release the button. This audio level will be
stored in memory, even after the detector
is turned off.
NOTE: To change the direction of
the audio ramping (e.g. down instead
of up) simply release the VOL button
quickly and press and hold again.
maintained on Ka-band and Laser
regardless of your speed.
Auto NoX (AutoMode with NoX)
Auto No X works the same as AutoMode
above; however, X-band is completely
turned off.
WARNING: Do not use the 9500ci
Auto NoX unless you are absolutely
certain that there are no traffic radar
guns using X-band in your area.
If you prefer, you can turn AutoMute
off. See the Preferences section for details.
6
7
Controls and Features
Safety Camera
Mark Locations
The first time you press the Mute
button, the audio will mute. The second
time the display will show “Lockout?”
accompanied by a voice prompt asking if
you want to lockout this signal. The third
time you press the Mute button, the
location and frequency of that signal is
stored in memory. The display will show
“Stored” to acknowledge the information
has been captured.
The warning distance for each label is:
Speed Trap =
.3 miles, or approximately 1,584 feet.
Speed Camera =
500’ when traveling below 55mph,
or 1000’ above 55mph
Red Light Camera =
250 feet
Your 9500ci comes pre-loaded with safety
camera locations in its memory. To turn
these on or off, see the “Markers” section
in Preferences.
The Mark Location feature allows you to
mark any location for future reference.
Once marked, the 9500ci will provide an
alert, accompanied by the label you
assigned to it, on the display.
There are (4) different labels you can
use when marking a location: Speed Trap
(“SPDTRAP”), Speed Camera (“SPDCAM”),
red light camera (“REDLIGHT”) and other
(“OTHER”).
To mark a location, simply press the
“MRK” button. The display will show
“MARK?”, accompanied by a voice message.
Press the “MRK” button again, and the
labels appear, starting with “SPDTRAP”. If
this is not the label you want to use,
simply press the “MUTE” button to scroll
through the other options. Once you
reached the label you want, simply press
the “MRK” button once more to confirm.
The word “MARKED” will appear on the
display, accompanied by a voice prompt
confirming you have marked and labeled
this location.
AutoLearn/Auto UnLearn
(X and K-bands only)
AutoLearn constantly analyzes all
incoming signals as you drive. If the same
signal is detected at the same location
approximately (3) three times, the 9500ci
will automatically lock it out as a false
alarm. Once this signal has been locked
out, no alert will be given at this location
unless it’s a new or different signal.
Once a signal has been locked out and
stored in memory, the 9500ci will also
automatically unlock a signal if it is not
present the next time you pass that
location. This reduces the chances of
locking out a real threat.
Other =
500’ when traveling below 55mph,
or 1000’ above 55mph
Audible Alerts
For Radar signals:
NOTE:
The 9500ci uses a Geiger-counter-like
sound to indicate the signal strength and
type of radar signal being encountered.
When you encounter radar, a distinct
audible alert will sound and occur faster
as the signal gets stronger. This allows you
to judge the distance from the signal
source without taking your eyes from the
road.
GPS must be on in Preferences.
Locking Out False Alarms
X-band = beep
K-band = brap
Ka-band = double-brap
POP = full double-chirp
Laser = rapid fire beeping
SWS = double buzz
To lock out a known false alarm, (X and K-
band radar, and Laser) simply press the
Mute button on the controller (3) three
times during the false alert.
NOTE: It is important to visually
look around to make certain no
traffic radar is present before locking
out a signal.
Once marked, the PASSPORT 9500ci
will provide an alert before you reach this
area the next time.
NOTE: You must drive out of the
marked area before the mark location
alert will work.
Example of a Mark Location labeled “Other.”
At low speeds, (below 20 mph) radar alerts
will be reduced to a double-tone based on
the band received (e.g. double brap for k-
band).
8
9
Controls and Features
For Laser signals:
Display Brightness
ExpertMeter
A few more examples will help you
better see how the ExpertMeter works.
Since laser signals are a possible
threat no matter how weak, the 9500ci
alerts you to these bands at full signal
strength.
The 9500ci’s display brightness is
automatically adjusted by a sensor located
behind the display lens. (factory default)
If you prefer, you can select one of the
following fixed levels of brightness
including Minimum, Medium, Maximum
or Full Dark by pressing the “BRT” button
located on the controller.
Your 9500ci’s ExpertMeter Display option
is an advanced display for experienced
detector users. Please use the 9500ci for a
few weeks to get familiar with its other
features before using this meter type.
To use the ExpertMeter instead of the
standard bar-graph signal strength meter,
you must select ExpertMeter in the
9500ci’s Preferences (see pages 12-15).
The 9500ci’s ExpertMeter Display
simultaneously tracks multiple radar
signals and their relative signal strength.
This can help you spot a change in your
normal driving environment. For example,
a traffic radar unit being operated in an
area where there are normally other
signals present.
|
K X
'
Here ExpertMeter shows a strong K-band
signal and a weak X-band signal.
For POP signals:
|
Ka X
Since POP signals are extremely fast K
or Ka bursts, and a possible threat no
matter how weak, the 9500ci alerts you to
these bands at full signal strength.
'
Here ExpertMeter shows a weak Ka-band
signal, and a strong X-band signal.
Signal Strength Meter
The 9500ci’s standard bar-graph meter
only displays information on a single radar
signal. If there are multiple signals present,
the 9500ci’s internal computer determines
which is the most important threat to
show on the bar-graph meter.
Spec Display
For Safety signals:
The 9500ci’s Spec Display option is for the
experienced detector user. In this mode,
the 9500ci will display the actual numeric
frequency of the radar signal being
received.
The 9500ci will alert you to these
signals with a double-beep tone, and a
corresponding text message. A complete
listing of the text messages
is on page 25.
When the 9500ci detects radar, it
displays the band (X, K, Ka), and a precise
bar-graph of the signal strength. When the
9500ci detects a laser signal, the display
will show “LASER.” When it detects a POP
signal, the display will show “POP.”
The ExpertMeter Display is actually a
miniature spectrum analyzer. It shows
what band each signal is and its signal
strength.
K 24.150
Spec Display shows one K-band
signal at 24.150 gigahertz.
Even long-time detector users will
require a significant amount of time to get
familiar with this new level of information
about detected signals.
Marked Locations
The 9500ci will alert you to marked
locations with a double-beep tone, and a
corresponding text message. A complete
list of mark location labels are on page 8.
|
Ka K X
' '
NOTE: If you are operating the
9500ci in the Dark mode, the display
will not display anything when a
signal is detected. However, the back
light on the Mute button, located on
the controller, will flash to give you a
visual alert.
Above is the ExpertMeter if the 9500ci
was detecting a strong Ka-band, a weak
K-band, and a weak X-band signal.
Voice Alerts
The 9500ci provides digital voice
announcements (factory default) for alerts,
feedback for button selections, and
preferences.
If you prefer, you can turn off the
voice feature in Preferences. See the
Preferences section for details.
10
11
How to use Preferences
Overview of Preferences
Press the VOL button
to go from one category
to the next
Press the BRT/CHG button
to change your setting
within a category
There are 10 user-selectable options you
can customize on your 9500ci. The
buttons labeled VOL and BRT on the
controller are used to enter Preferences.
Once you enter Preferences, the VOL
button is used to REVIEW your current
choices, and BRT button is used to
CHANGE settings. See Pages 14-16 for
more detail.
An example
Here is how you would turn the AutoMute
feature off.
PILOT
Pilot HWY * Full word: Highway, AutoScan, etc.
(Power-on indication)
Pilot H
Letter: H, A, ANX
Letter, with scanning dot
Vehicle voltage
1
Enter Preferences by holding both the
Pilot H.>
Pilot V
VOL and BRT buttons down for 2 seconds.
Pilot SPD
Vehicle speed
The 9500ci will beep twice and display Prefs.
GPS
AUTOLEARN
SPEED ALERT
METER
GPS ON
GPS OFF
* GPS On
GPS Off
2
Then hold the VOL/RVW button down.
aLrn ON
aLrn OFF
* AutoLearn On
AutoLearn Off
The 9500ci will scroll through the categories,
starting with Pilot, GPS, aLearn, Meter,
then AutoMute.
How to use Preferences
sAlrt ON
sAlrt OFF
* Speed Alert On
Speed Alert Off
1
To enter Preferences, press and
Meter STD * Bar-graph Meter
hold both the VOL and BRT buttons
down for 2 seconds. (The unit will display
the word Prefs, accompanied by a voice
announcement).
3
Release the VOL/RVW button when the
Meter EXP
Meter SPC
Expert Meter
Spec Display
9500ci shows the AutoMute item. Since the
factory setting for AutoMute is on, the display
will show aMuteON.
(If you accidentally don’t release the VOL/
RVW button in time, and 9500ci goes to the
next category, simply hold the VOL /RVW
button down again, the 9500ci will scroll
through all of the categories.)
AUTOMUTE
UNITS
aMute ON
aMute OFF
* AutoMute On
AutoMute Off
Units ENG * Units English
2
Press the VOL button to review the
Units MET
Units Metric
current settings. (You can either tap the
button to change from item to item, or hold
the button to scroll through the items).
VOICE
Voice ON
Voice OFF
* Voice Alerts On
Voice Alerts Off
BANDS
Bands DFT * Factory Default Settings
Bands MOD
Factory Default Settings Modified
3
Press the BRT button to change any
4
Press the BRT/CHG button to change
Turn bands ON or Off by
pressing the MUTE button
*Factory Default Settings
To reset 9500ci to its
original factory
settings, press and
hold the “VOL” and
“SENS” buttons
while turning the
power on. The
setting. (You can either tap the button to
change from setting to setting, or hold the
button to scroll through all the options).
from aMuteONto aMuteOFF.
ONor OFF(default is on)
ONor OFF(default is on)
ONor OFF(default is on)
ONoorr OFF(default is off)
X
ON OFF
5
To exit Preferences, simply wait 8
K
Ka
POP
SWS
LSR
seconds without pressing any button, or
press the PWR button ( ). The 9500ci will
display Complete, accompanied by a voice
announcement.
4
To exit Preferences, simply wait 8
RECVor SHFTor
(defaultOisFoFff()default is RECV)
seconds without pressing any button,
or press the PWR button ( ). (The unit
will display Complete, accompanied by a
voice announcement).
9500ci’s display will
provide a Reset
message, accompa-
nied by an audible
alert, acknowl-
MARKERS
Mark DFT * Factory Default Settings
Mark MOD Factory Default Settings Modified
rCam ON OFF
sCam ONor OFF(default is on )
Trap ONor OFF(default is on)
Othr ONoorr OFF((ddeeffaauulltt iiss oonn))
edging the reset.
12
13
Details of Preferences
Pilot (Power-on indication)
Pilot HWY (Full word)
In this setting, the 9500ci will display
“Highway,” “Auto,” or “AutoNox” as its
power-on indication. (factory default)
Speed Alert
AutoMute
aMute ON (AutoMute on)
Pilot SPD (Vehicle speed)
In this setting, the 9500ci will display “H”
for Highway, “A” for Auto, and “Anx” for
Auto NoX, accompanied by the vehicle’s
speed.
sAlrt On (Speed Alert is on)
In this setting, your current vehicle speed
is displayed, then the meter you’ve
selected. (factory default)
In this setting, the 9500ci’s audio alerts
will initially be set to the volume you set,
but after a few seconds, the 9500ci will
automatically reduce the volume level, to
keep you informed, but not annoyed.
(factory default)
Pilot H (Letter)
sAlrt On (Speed Alert is off)
In this setting, speed alert is off.
NOTE: When you are using the
Dark mode, the display will not
display anything. Only the power-on
indication on the controller will
illuminate.
In this setting, the 9500ci will display “H”
for Highway, “A” for Auto, and “Anx” for
Auto No X.
Signal Strength Meter
aMute OFF (AutoMute off)
MeterSTD (Standard meter)
In this setting, the meter displays the band
of the signal received, and a bar-graph
showing the relative signal strength.
(factory default)
With AutoMute off, the 9500ci’s audio
alerts will remain at the volume you set for
the duration of the encounter.
Pilot H.> (Letter with scrolling dot)
In this setting, the 9500ci will display “H”
for Highway, “A” for Auto, and “Anx” for
Auto No X, accompanied by a scrolling dot.
GPS
GPS On (GPS receiver on)
In this setting, all GPS related features are
on. (factory default)
Units
Units ENG (units are in English)
In this setting, all speed and distance
related functions are displayed in English
units. (factory default)
Pilot V (Vehicle voltage)
MeterEXP (ExpertMeter)
In this setting, the meter will
simultaneously track multiple radar
signals, including relative signal strength
for each.
In this setting, the 9500ci will display “H”
for Highway, “A” for Auto, and “Anx” for
Auto NoX, accompanied by the vehicle’s
voltage.
GPS Off (GPS receiver off)
In this setting, all GPS features are off.
Units MET (units are in Metric)
In this setting, all speed and distance
related functions are displayed in Metric
units.
Auto Learn
aLrn On (AutoLearn is on)
In this setting, the 9500ci will constantly
analyze all incoming radar signals and lock
out false alarms automatically over time.
(factory default)
NOTE: A high or low voltage
Meter SPC (Spec Display meter)
In this setting, the meter will display the
actual numeric frequency of the radar
signal received.
warning is given any time the vehicle’s
voltage drops below 10.5 volts, or goes
above 16.5 volts. This feature is always
on, regardless of the Pilot setting.
NOTE: The Spec Display feature is
explained in more detail on page 11.
aLrn Off (AutoLearn is off)
In this setting, any false alerts will need to
be locked out manually using the Mute
button.
14
15
Details of Preferences
Specifications
Bands
BandsDFT
Markers
MarkDFT
Features and Specifications
In this setting, the factory default settings
for North America radar and laser are
monitored.
This is the factory setting, and it is
highly recommended that you use your
9500ci in this mode.
In this setting, all fixed location reporting,
including safety cameras, red light
cameras and speed traps are reported.
Operating Bands
Sensitivity Control
• Highway
•Auto
•Auto NoX
Additional Patented Technology
•AutoLearn™
• X-band 10.525 GHz ±25 MHz
• K-band 24.150 GHz ±100 MHz
• Ka-band 34.700 GHz ±1300 MHz
• Laser 904nm,±33nm
Radar Receiver
MarkMOD
In this setting, only the Markers you’ve
selected will be reported.
• Dual-HornAntenna Casting
• Superheterodyne,dual LNA’s
• Scanning Frequency Discriminator
• Digital Signal Processing (DSP)
Laser Detection
• Quantum LimitedVideo Receiver
• (9) Receive,(24)Transmit
Display Type
• 280 LEDAlphanumeric
• Bar Graph,ExpertMeter™ or
Spec Display™
•Automatic,plus 4 levels of fixed
brightness including full Dark
Power Requirement
• 12VDC,Negative Ground
Preferences
• Mute/AutoMuteTM/SmartMute™
•TotalShield™Technology
Patented Technology
PASSPORT is covered by one or more of
the following patents:
BandsMOD
In this setting, 9500ci will warn you with
an audible alert, and associated text
message stating which band has changed
from the original factory setting (e.g. “SWS
ON”). This warning is displayed during
the start up sequence.
Laser Shifters
Your 9500ci is equipped with a total of (3)
Laser Shifters, (2 front, 1 rear). These
transceivers will automatically receive
incoming laser signals.
If you prefer, you can turn on the
Laser Shifters to automatically “shift”
incoming signals. See the Preferences
section for details.
U.S.Patents
7,098,844 6,836,238 6,779,765 6,693,578
6,670,905 6,614,385 6,587,068 6,400,305
6,249,218 6,127,962 6,069,580 5,668,554
5,600,132 5,587,916 5,559,508 5,446,923
5,402,087 5,365,055 5,347,120 5,305,007
5,206,500 5,164,729 5,134,406 5,111,207
5,079,553 5,049,885 5,049,884 4,961,074
4,954,828 4,952,937 4,952,936 4,939,521
4,896,855 4,887,753 4,862,175 4,750,215
4,686,499 4,631,542 4,630,054 4,625,210
4,613,989 4,604,529 4,583,057 4,581,769
4,571,593 4,313,216 D314,178 D313,365
D310,167 D308,837 D296,771 D288,418
D253,752
WARNING: Do not turn off any
bands unless you are absolutely
certain there are no traffic radar
guns using that specific band in your
area.
• Pilot
• GPS
•AutoLearn
• SpeedAlert
• Meter
Canadian Patents
•AutoMute
• Units
2,337,077 2,330,964 1,295,715 1,295,714
1,187,602 1,187,586
•VoiceAlerts
European Patents
• Bands
1,145,030 1,090,456
• Markers
Other patents pending.
16
17
Interpreting Alerts
Alert
Explanation
Although the 9500ci has a comprehensive
warning system and this Manual is as
complete as we can make it, only
experience will teach you what to expect
from your 9500ci and how to interpret
what it tells you. The specific type of radar
being used, the type of transmission
(continuous or instant-on) and the location
of the radar source affects the radar alerts
you receive.
The following examples will give you
an introduction to understanding the
9500ci’s warning system for radar, laser
and safety alerts.
The 9500ci alerts intermittently. Rate and
strength of alerts may be consistent or vary
wildly.
A patrol car is travelling in front of you with
a radar source aimed forward. Because
signals are sometimes reflected off of large
objects and sometimes not, the alerts may
seem inconsistent.
The 9500ci alerts intermittently. Rate and
strength of signal increases with each alert.
A patrol car is approaching from the other
direction, sampling traffic with instant-on
radar. Such alerts should be taken seriously.
Alert
Explanation
The 9500ci begins to sound slowly, then the
rate of alert increases until the alert becomes
a solid tone. The Signal Meter ramps
accordingly.
You are approaching a continuous radar
source aimed in your direction.
The 9500ci gives an X-band alert
intermittently.
You are driving through an area populated
with radar motion sensors (door openers,
burglar alarms, etc.). Since these
transmitters are usually contained inside
buildings or aimed toward OR away from
you, they are typically not as strong or
lasting as a real radar encounter.
The 9500ci emits short alerts for a few
seconds and then falls silent only to briefly
alert and fall silent again.
An instant-on radar source is being used
ahead of you and out of your view.
The 9500ci suddenly sounds a continuous
tone for the appropriate band received. All
segments in the Signal Strength Meter are lit.
An instant-on radar source or laser source is
being used nearby. This kind of alert
requires immediate attention!
CAUTION: Since the characteris-
tics of these alerts may be similar to
some of the preceding examples,
over-confidence in an unfamiliar
area can be dangerous. Likewise, if
an alert in a commonly traveled
area is suddenly stronger or on a
different band than usual, speed
radar may be set up nearby.
A brief laser alert.
Laser is being used in the area. Because laser
is inherently difficult to detect, any laser
alert may indicate a source very close by.
The 9500ci receives weak signals. These
signals may be a little stronger as you
pass large, roadside objects. The signals
increase in frequency.
A moving patrol car with continuous radar is
overtaking you from behind. Because these
signals are reflected (reflections are
increased by large objects), they may or may
not eventually melt into a solid point even
when the patrol car is directly behind you.
The 9500ci alerts slowly for awhile and then
abruptly jumps to a strong alert.
You are approaching a radar unit concealed
by a hill or an obstructed curve.
18
19
How Radar Works
How POP Works
How Laser Works
How Radar Works
Traffic radar, which consists of
Radar range also depends on the
power of the radar equipment itself.
The strength of the radar unit’s beam
diminishes with distance. The farther the
radar has to travel, the less energy it has
for speed detection.
Because intrusion alarms and motion
sensors often operate on the same
frequency as X, and K-band radar, your
PASSPORT will occasionally receive non-
police radar signals. Since these X-Band
transmitters are usually contained inside
of a building, or aimed toward the ground,
they will generally produce much weaker
readings than will a true radar encounter.
As you become familiar with the sources
of these pseudo alarms in your daily
driving, they will serve as confirmation
that your PASSPORT’s radar detection
abilities are fully operational.
How “POP” Works
LIDAR (or laser) is a newer technology
and is not as widespread as conventional
radar, therefore, you may not encounter
laser on a daily basis. And unlike radar
detection, laser detection is not prone to
false alarms. Because LIDAR transmits a
much narrower beam than does radar, it is
much more accurate in its ability to
distinguish between targets and is also
more difficult to detect. As a result, even
the briefest laser alert should be
taken seriously.
“POP” mode is a relatively new feature for
radar gun manufacturers. It works by
transmitting an extremely short burst,
within the allocated band, to identify
speeding vehicles in traffic. Once the
target is identified, or “POPPED,” the gun
is then turned to its normal operating
mode to provide a vehicle tracking history,
(required by law).
NOTE: According to the operator’s
manual from the radar gun manufac-
turer, tickets should not be issued in
POP mode.
microwaves, travels in straight lines and is
easily reflected by objects such as cars,
trucks, even guardrails and overpasses.
Radar works by directing its microwave
beam down the road. As your vehicle
travels into range, the microwave beam
bounces off your car, and the radar
antenna looks for the reflections.
Using the Doppler Principle, the radar
equipment then calculates your speed by
comparing the frequency of the reflection
of your car to the original frequency of the
beam sent out.
Traffic radar has limitations, the most
significant of these being that it typically
can monitor only one target at a time. If
there is more than one vehicle within
range, it is up to the radar operator to
decide which target is producing the
strongest reflection. Since the strength of
the reflection is affected by both the size
of the vehicle and its proximity to the
antenna, it is difficult for the radar
operator to determine if the signal is from
a sports car nearby or a semi-truck several
hundred feet away.
There are limitations to LIDAR
equipment. LIDAR is much more sensitive
to weather conditions than RADAR, and a
LIDAR gun’s range will be decreased by
anything affecting visibility such as rain,
fog, or smoke. A LIDAR gun cannot
operate through glass and it must be
stationary in order to get an accurate
reading. Because LIDAR must have a clear
line of sight and is subject to cosine error
(an inaccuracy, which increases as the
angle between the gun and the vehicle,
increases) police typically use LIDAR
equipment parallel to the road or from an
overpass. LIDAR can be used day or night.
How Laser (Lidar) Works
Laser speed detection is actually LIDAR
(Light Detection and Ranging). LIDAR
guns project a beam of invisible infrared
light. The signal is a series of very short
infrared light energy pulses which move
in a straight line, reflecting off your car
and returning to the gun. LIDAR uses
these light pulses to measure the distance
to a vehicle. Speed is then calculated by
measuring how quickly these pulses are
reflected given the known speed of light.
20
21
How GPS Works
How TotalShield™ Works
How TrueLock Works
How AutoLearn Works
How GPS Works
The Global Positioning
System (GPS) is made up of
How TotalShield Works
How TrueLock Works
How AutoLearn Works
ESCORT’s TotalShield Technology keeps
RF signals from radiating from the
detector. Unlike other radar and laser
detectors, which merely move their RF
signals (local oscillators) to another
frequency (which will be detectable by
future detector-detectors), this
TrueLock uses exact position and the
actual frequency of a signal to eliminate it
as a false alarm. Once a signal is locked out,
a box is created (approximately a 1⁄2 mile
radius) around that location to lock it out
from all directions.
NOTE: Thoroughly look around
and make sure that no real radar is
being used to monitor your speed
before you manually lock out a signal.
Automatic door openers use more
than one source, so TrueLock will
automatically lock out other X and K-band
sources in close proximity of the first to
captures these.
AutoLearn uses TrueLock to lock out false
alerts, however signals are locked out
automatically over time vs. manually using
the Mute button.
As you drive, PASSPORT records
location and frequency for each signal
detected. If that same signal (by
frequency) is in the same location
approximately three (3) times, AutoLearn
will automatically lock it out as a false
alarm. A “stored” message will be
displayed, accompanied by a low-level
alert.
twenty four orbiting satellites and was
developed by the U.S. military. There are
at least four satellites visible at any given
time every day.
A GPS receiver is designed to locate
and receive data from four of these
satellites. This data includes the distance
to your location from each of the satellites.
Once the distance from each satellite is
known, the receiver can calculate and
pinpoint your exact location.
revolutionary design keeps you unseen by
current radar detector-detectors,
including VG-2 and Spectre. This unique
design will also keep you unseen from any
future radar detector detectors as well.
Although the PASSPORT 9500ci is a
completely undetectable radar, laser and
safety detector, driving techniques and
reactions to alerts can still draw unwanted
attention. Here are a few examples:
1. Hitting the brakes immediately when
the 9500ci provides an alert can broadcast
use of a detector.
2. Traveling at night with a glow from a
radar detector’s display visible from
outside your vehicle can also draw
unwanted attention. The 9500ci offers
adjustable brightness, including a full dark
mode which will provide audio alerts, but
no visual indication.
How Auto Unlearn Works
If you accidentally lock out a real
threat, (visually see the officer) simply
press and hold the Mute button to unlock
it from PASSPORT’s memory.
Auto Unlearn automatically unlocks stored
TrueLock signals if they are not present in
the same location. This is particularly
useful if you accidently lock out a true
threat, or if an officer is parked in a
shopping mall with automatic door
openers.
22
23
How Safety Radar Works
How SWS Works
Since Safety radar technology is
relatively new and the number of
transmitters in operation is not yet
widespread, you will not receive
SWS Text Messages
Highway Construction or Maintenance
1 Work Zone Ahead
Weather Related Hazards
33 High Wind Ahead
34 Severe Weather Ahead
35 Heavy Fog Ahead
36 High Water/Flooding Ahead
37 Ice On Bridge Ahead
38 Ice On Road Ahead
39 Blowing Dust Ahead
40 Blowing Sand Ahead
41 Blinding Snow Whiteout Ahead
42 For future use
Travel Information/Convenience
43 Rest Area Ahead
44 Rest Area With Service Ahead
45 24 Hour Fuel Service Ahead
46 Inspection Station Open
47 Inspection Station Closed
48 Reduced Speed Area Ahead
49 Speed Limit Enforced
50 Hazardous Materials Exit Ahead
51 Congestion Ahead/Expect Delay
52 Expect 10 Minute Delay
53 Expect 20 Minute Delay
54 Expect 30 Minute Delay
55 Expect 1 Hour Delay
There are two separate Safety Radar
systems in limited use today: Safety Alert
and Safety Warning System (SWS). Both
systems use modified K-band radar signals.
From the factory, your PASSPORT is
programmed with safety radar decoding
OFF. If Safety Radar is used in your area,
your PASSPORT will display these signals
as K-band radar signals instead of safety
radar unless you use the Preferences to
turn PASSPORT’s safety radar decoding ON.
The Safety Alert safety radar system
has three possible alerts:
2 Road Closed Ahead/Follow Detour
3 Bridge Closed Ahead/Follow Detour
4 Highway Work Crews Ahead
5 Utility Work Crews Ahead
6 All Traffic Follow Detour Ahead
7 All Trucks Follow Detour Ahead
8 All Traffic Exit Ahead
9 Right Lane Closed Ahead
10 Center Lane Closed Ahead
11 Left Lane Closed Ahead
12 For future use
Safety signals on a daily basis and should
not be surprised to encounter emergency
vehicles, road hazards and railroad
crossings that are unequipped with these
transmitters and, therefore, fail to provide
a signal. As Safety transmitters become
more prevalent (the number of operating
transmitters is growing every day), these
Safety radar signals will become more
common.
• Safety Vehicle
• Road Hazard
• Train Nearby
Highway Hazard Zone Advisory
13 Stationary Police Vehicle Ahead
14 Train Approaching/At Crossing
15 Low Overpass Ahead
The SWS safety radar system has 64
possible messages (60 currently allocated).
The SWS messages your PASSPORT can
display are listed on the facing page.
NOTE: Some of the safety
messages have been condensed, so
each message can be displayed on one
or two screens on PASSPORT’s eight
character display.
16 Drawbridge Up
17 Observe Drawbridge Weight Limit
18 Rock Slide Area Ahead
19 School Zone Ahead
20 Road Narrows Ahead
21 Sharp Curve Ahead
22 Pedestrian Crossing Ahead
23 Deer/Moose Crossing
24 Blind/Deaf Child Area
56 Traffic Alert/Tune AM Radio
57 Pay Toll Ahead
25 Steep Grade Ahead/Truck Use Low Gear 58 Trucks Exit Right
26 Accident Ahead
59 Trucks Exit Left
60 For future use
Fast/Slow MovingVehicles
61 Emergency Vehicle In Transit
62 Police In Pursuit
27 Poor Road Surface Ahead
28 School Bus Loading/Unloading
29 No Passing Zone
30 Dangerous Intersection Ahead
31 Stationary Emergency Vehicle Ahead 63 Oversize Vehicle In Transit
32 For future use
64 Slow Moving Vehicle
24
25
Troubleshooting
Problem
Solution
Explanation of Displays
PASSPORT beeps briefly at the
same location every day, but no
radar source is in sight.
• An X or K-band motion sensor or intrusion alarm is
located within range of your route. You can manually
lock this out using TrueLock, or allow AutoLearn to
do it over time.
Lsr R
N/A
There is a problem with the rear laser receiver (it could be an
unplugged connection, damaged wiring, or a problem within the rear
laser unit itself).
Check
Receiver
Wiring
There is a problem with the front receiver (it could be an unplugged
connection, damaged wiring, or a problem within the front receiver
itself). PASSPORT will continue to display this message, and will not
operate until the problem has been repaired.
PASSPORT does not seem
sensitive to radar or laser.
• PASSPORT may be in Auto or AutoNox mode.
PASSPORT did not alert when a
police car was in view.
• VASCAR, (Visual Average Speed Computer And
Recorder) a stopwatch method of speed detection,
may be in use.
ANX
Sensitivity control is in Auto No X-band. (page 7)
Sensitivity control is in Highway mode. (page 14)
One of the many options in Preferences (pages 12-16)
One of the many Safety Radar messages (pages 24-25)
H
PASSPORT only beeped twice
during a radar encounter.
• This is normal. Full alerts are minimized when
traveling below 25 mph.
PilotHWY
WorkZone
Caution
PASSPORT’s audible alerts are
less loud after the first few
alerts.
• PASSPORT is in AutoMute Mode. See page 4 for
details.
PASSPORT has detected a Safety Radar Signal, but the signal isn’t yet
strong enough to decode the specific safety message (pages 24-25)
PASSPORT’s power-on
sequence reoccurs while you
are driving.
• A loose power connection can cause PASSPORT to
be briefly disconnected, and will retrigger the power-
on sequence.
|
or K
or KA etc.
X
PASSPORT has been programmed in the ExpertMeter Mode (page 11)
|
|
Your 14-year old son has
changed all of your Preferences.
• You can return all of the Preferences to their factory
defaults by holding down the SENS and VOL buttons
while you turn PASSPORT on.
Receiver
Error
PASSPORT has failed to calibrate. Contact your Dealer for repair.
Not able to receiver GPS signal. Check GPS antenna connection.
PASSPORT will not turn on.
• Check that the PWR button is ON.
• Check that vehicle ignition is ON.
• Check all connections.
GPS N/A
26
27
Service
Warranty
Service Procedure
If Your PASSPORT ever needs service,
please follow these simple steps:
ESCORT One Year
Limited Warranty
What this warranty covers: ESCORT
warrants your Product against all defects
in materials and workmanship.
For how long: One (1) year from the date
of the original purchase.
What we will do: ESCORT, at our discre-
tion, will either repair or replace your
Product free of charge.
What we will not do: ESCORT will not
pay shipping charges that you incur for
sending your product to us.
your product and include: your name,
complete return address, written descrip-
tion of the problem with your product,
daytime telephone number, and a copy of
the original purchase receipt. 3. Label the
outside of the package clearly with your
Return Authorization number. Ship the
product pre-paid (insured, for your protec-
tion) to: ESCORT Inc, 5440 West Chester
Rd., West Chester, OH 45069.
1
Check the troubleshooting section of
this manual. It may have a solution to your
problem.
2
Contact your installing dealer. They
will evaluate your unit and arrange repairs
if necessary.
LIMITATION OF WARRANTY: EXCEPT
AS EXPRESSLY PROVIDED HEREIN, YOU
ARE ACQUIRING THE PRODUCT “AS IS”
AND “WHERE IS,” WITHOUT
What you must do to maintain this
warranty: Show original proof of pur-
chase from an authorized ESCORT dealer.
Warranty Exclusions: Warranty does not
apply to your product under any of the fol-
lowing conditions: 1. The serial number has
been removed or modified. 2. Your product
has been subjected to misuse or damage
(including water damage, physical abuse,
and/or improper installation). 3. Your pro-
duct has been modified in any way. 4. Your
receipt or proof-of-purchase is from a non-
authorized dealer or internet auction site
including E-bay, U-bid, or other non-autho-
rized resellers. 5. You are not the original
purchaser of the radar detector from an
authorized dealer or did not receive it as a
gift from the original purchaser of the
radar detector from an authorized dealer.
To obtain service: 1. Contact ESCORT
(1-800-543-1608) to obtain a Return
Authorization Number. 2. Properly pack
REPRESENTATION OR WARRANTY.
ESCORT SPECIFICALLY DISCLAIMS ANY
REPRESENTATION OR WARRANTY
INCLUDING, BUT NOT LIMITED TO
THOSE CONCERNING THE MERCHANT-
ABILITY AND SUITABILITY OF THE
PRODUCT FOR A PARTICULAR PURPOSE.
ESCORT SHALL NOT BE LIABLE FOR
CONSEQUENTIAL, SPECIAL OR
INCIDENTAL DAMAGES INCLUDING,
WITHOUT LIMITATION, DAMAGES
ARISING OUT OF THE USE, MISUSE OR
MOUNTING OF THE PRODUCT.
The above limitations or exclusions shall
be limited to the extent they violate the
laws of any particular state. ESCORT is not
responsible for products lost in shipment
between the owner and our service center.
Other legal rights: This Warranty gives
you specific rights. You may have other
legal rights, which vary, from state to state.
FCC Note: Modifications not expressly
approved by the manufacturer could
void the user’s FCC granted authority
to operate the equipment.
28
29
Register
online:
@www
EscortRadar.com
30
31
32
33
|