Earthquake Sound Speaker 600WRMS User Manual

MODEL  
SuperNova MKVI  
Class "J" Powered  
Subwoofer  
600WRMS  
U S E R M A N U A L  
Earthquake Sound Corporation | 2727 McCone Avenue, Hayward CA 94545  
Sound That Will Move You.  
 
SuperNova MKVI  
Unpacking and Warnings  
ITEMIZED LIST OF INCLUDED ITEMS:  
1. One (1)AC Power Cable  
2. One (1) Owners' Manual  
3. One (1) Registration Card  
4. One (1) Remote Control  
5. One (1) SuperNova Subwoofer  
When you have safely removed the subwoofer from the packaging and placed it in a safe area, perform a thorough physical inspection and report any damage to the  
dealer that you purchased the unit from. We suggest that you keep the original packaging, and that it should be stored in a safe, dry place in case you’re required to  
transport the unit.The customized packaging is specially designed toprotect the amplifier from potential damage that can arise when shipping such a product.  
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Do not attempt to “lift the ground” by removing the  
WARNING!  
ground pin from theAC cable. Make sure that your household electrical wiring supports properAC grounding techniques before plugging  
in this product. Keep the heat sinks and top cover free of dust to allow for proper heat dissipation. Never expose this product to extreme  
temperature. Always connect the audio signal path cable prior toconnecting theAC mains.  
No user-serviceable parts inside. Do not attempt to remove cover or repair this product, as severe electrical shock may result and it may  
disrupt your warranty.  
CAUTION!  
Make sure that your localAC voltage complies with the unit’s label. Damage caused by plugging this subwoofer into anAC receptacle of  
the wrong voltage will not be covered by warranty.  
IMPORTANT!  
Specifications Are Subject To Change Without Notice  
3
 
SuperNova MKVI  
Subwoofer Placement Guide  
GOOD / This illustration shows a single subwoofer setup  
Why having two gains on a mono subwoofer is  
a good thing?  
The blue arrow represents the subharmonic  
frequencies as they move always toward the sub in  
the single sub system. The red arrow represents  
the lows + mids + highs as they follow the action.  
Often you hear the term “subwoofers are non-directional”;  
this is not true. Subwoofer placement is harder to pick when  
two low frequencies are crossed. The wider the room, the  
more directional the subwoofer. The easiest solution is to use  
two subwoofers in the front: one on the left and a second on  
the right. The signal to both is mono. In some applications,  
users might have small front speakers or planar speakers.  
Both speakers have an early roll off in the sub-harmonics.  
The planar needs help from 150Hz on down, having two front  
subwoofers placed on the left and the right is a healthy  
solution tothis problem.  
Note: The breakaway and the image separation.  
best response when blue and the red are identical.  
BETTER / This illustration shows dual subwoofer with mono signal  
Two Subs  
The blue arrow represents the sub-harmonic  
frequencies as they move always toward the  
middle in a mono-two-subs- system. The red arrow  
represent the lows+ the mids+ highs as they follow  
the action,  
While having two subwoofers is better than one, the MONO  
signal that drives these subwoofer keeps them from  
projecting the three dimensional images in the sub-  
harmonics. The use of two subwoofers allows you to cross  
the subs up to 150Hz sound quality, imaging and staging.  
The two-front-subwoofer-system is an excellent solution to  
planar speaker’s low frequency response early roll off. When  
locating these subwoofers in a close proximity to the stereo  
satellite, the subs will enhance low frequency extension. It  
will be better to have a stereo subwoofer to help in the lower  
bass notes and their placement.  
Note: the breakaway and the image separation.  
If a bass Guitar player was standing on the left side of the  
stage and he played an EE note (42Hz), then the right sub will  
also respond to that and create havoc on the stage. In fact, if  
you only have one single sub in the room and it’s placed on  
the right side of the room, while the bass guitar player is  
playing his music on the left side of the stage. As soon as he  
hits the EE note, the sub speaks out on the right and  
completely destroys the stage. To give you three-  
dimensional front-end bass that allows you to have a low  
frequency dynamic stage, Earthquake designed dual input  
circuits that use buffers to maintain your stereo separation on  
the processor side while mixing stereo front signals to  
produce 3D bass.  
BEST / This illustration shows dual subwoofers with stereo+mono signals  
In this illustration, the stereo subwoofers keep the  
sub-harmonics dynamically synchronized in  
motion with the rest of the audio systems. Fully  
complementing the sub-harmonics for mids and  
the highs  
Specifications Are Subject To Change Without Notice  
4
 
SuperNova MKVI  
Front and Back Panel Overview  
24dB/Oct  
Switchable  
Subsonic Filter  
0°-180° Phase Shift  
WE RECOMMEND  
THE ON POSITION  
0-20 MS.Phase Delay  
CROSSOVER  
SUBSONIC  
PHASE DELAY  
PHASE SHIFT  
20, 30 and 40Hz  
24dB/Oct  
Individual Channel  
Gain Controls  
Room Equalization  
Lowpass  
ON  
BY PASS  
ON  
OFF  
20Hz  
0
20ms  
0°  
180°  
With 12dB range  
With Bypass  
and Boost  
Channel Status LEDs  
-40Hz  
ON  
200Hz  
-6dB  
+6dB  
GAIN 2  
GAIN 1  
30Hz  
40Hz  
2
1
AUTO  
OFF  
Required LFE Inputs  
Use One Only  
Auto Sensing  
-6dB  
-6dB  
+6dB  
+6dB  
RCA  
XLR  
RCA  
XLR  
IR INPUT  
RCA Inputs  
Remote Sensor Input  
CORRECTION  
ON  
XLR Inputs  
110-120VAC  
SPK  
SPK  
Removable  
AC Power  
Supply Cord  
220-240VAC  
Speaker Level Input  
OFF  
POWER  
110-120V ~ /60Hz  
220-240 ~ /50Hz  
600W  
POWEED SUBWOOFER  
CAUTION VORSICHT  
BEFORE OENING  
PULL MAIN PLUG  
VOR DEM ÖFFNEN  
NETZSTECKER ZIEHEN  
Fuse box  
Specifications Are Subject To Change Without Notice  
5
 
SuperNova MKVI  
Dual Subwoofer Stereo Connection  
INPUT  
LEFT  
Split L/R RCA's To Amplifier's  
LEFT/RIGHT Channels.  
RIGHT  
The back side of a typical processor or receiver  
MAIN AUDIO OUTPUTS  
LEFT  
LEFT SUR  
CENTER  
RIGHT  
RIGHT SUR  
SUB  
CROSSOVER  
SUBSONIC  
PHASE DELAY  
PHASE SHIFT  
CROSSOVER  
SUBSONIC  
PHASE DELAY  
PHASE SHIFT  
ON  
BY PASS  
ON  
OFF  
20Hz  
ON  
BY PASS  
ON  
OFF  
20Hz  
0
20ms  
0°  
180°  
0
20ms  
0°  
180°  
-40Hz  
ON  
200Hz  
-6dB  
+6dB  
-40Hz  
ON  
200Hz  
-6dB  
+6dB  
2  
GAIN 1  
GAIN 2  
GAIN 1  
30Hz  
40Hz  
30Hz  
40Hz  
2
1
2
1
AUTO  
OFF  
AUTO  
OFF  
-6dB  
-6dB  
+6dB  
+6dB  
-6dB  
-6dB  
+6dB  
+6dB  
RCA  
XLR  
RCA  
XLR  
XLR  
RCA  
XLR  
IR INPUT  
IR INPUT  
EQUALIZER  
ON  
EQUALIZER  
ON  
110-120VAC  
110-120VAC  
SPK  
SPK  
SPK  
SPK  
220-240VAC  
220-240VAC  
OFF  
OFF  
POWER  
POWER  
110-120V ~ /60Hz  
220-240 ~ /50Hz  
600W  
110-120V ~ /60Hz  
220-240 ~ /50Hz  
600W  
POWERED SUBWOOFER  
CAUTION VORSICHT  
BEFORE OPENING  
PULL MAIN PLUG  
POWERED SUBWOOFER  
CAUTION VORSICHT  
BEFORE OPENING  
PULL MAIN PLUG  
VOR DEM ÖFFNEN  
NETZSTECKER ZIEHEN  
VOR DEM ÖFFNEN  
NETZSTECKER ZIEHEN  
The same wiring configuration can be  
duplicated for the XLR inputs. NOTE: We  
provide three different input types, but  
do not recommend mixing input types.  
Specifications Are Subject To Change Without Notice  
6
 
SuperNova MKVI  
Single Subwoofer Mono Connection  
The back side of a typical processor or receiver  
MAIN AUDIO OUTPUTS  
LEFT  
LEFT SUR  
CENTER  
RIGHT  
RIGHT SUR  
SUB  
CROSSOVER  
SUBSONIC  
PHASE DELAY  
PHASE SHIFT  
ON  
BY PASS  
ON  
OFF  
20Hz  
0
20ms  
0°  
180°  
-40Hz  
ON  
200Hz  
-6dB  
+6dB  
GAIN 2  
GAIN 1  
30Hz  
40Hz  
2
1
AUTO  
OFF  
-6dB  
-6dB  
+6dB  
+6dB  
RCA  
XLR  
RCA  
XLR  
IR INPUT  
EQUALIZER  
ON  
Usually one RCA has enough signal to  
drive the IQ amplifier to its full output.  
However, in some cases where signal is  
too low for the IQ amp to produce its full  
output, you may use a " Y" connector to  
increase the amp's sensitivity.  
110-120VAC  
SPK  
SPK  
220-240VAC  
OFF  
POWER  
110-120V ~ /60Hz  
220-240 ~ /50Hz  
600W  
POWERED SUBWOOFER  
CAUTION VORSICHT  
BEFORE OPENING  
PULL MAIN PLUG  
VOR DEM ÖFFNEN  
NETZSTECKER ZIEHEN  
Specifications Are Subject To Change Without Notice  
7
 
SuperNova MKVI  
Room Correction  
The MKVIs' amplifier offers a room correction technique that surpasses all previous  
attempts. The intelligent “Back emf” drive circuit interacts with the subwoofer design  
and memorizes system tuning frequencies as well as system type. The information,  
which is stored in microprocessor, turns on a preset group delay curve that serves as a  
correction reference. This information deals only with time correction that moves the  
peaks and the dips in a room to a flat. Once that is achieved, the user will resort to the  
final correction- EQ the room. For that reason, Earthquake’s SuperNova MKVI is truly  
an intelligent system. 20Hz, 30Hz and 40Hz frequencies can be cut or boosted by a  
whopping 6dB, these corrections help in producing wider range of listening position  
that is unprecedented forthe room.  
To begin the process of room correction, you should have two people: One  
person will make adjustments at the amplifier and the other at the meter.  
When setting the room EQ, do not over power the speakers. As this  
may cause them to bottom out or cause other more severe problems  
that your warranty will not cover. To set up the room EQ, you will need  
a spectrum-analyzer, or you can use the rule of thumb.  
STEP 1: Place your subwoofer in the most desirable area.  
STEP 2: Have the second person sit on a chair or sofa with a testing  
microphone or SPL meter.  
STEP 3: Load "white Noise" CD or 50Hz tone continuous.  
STEP 4: With the amp phase at 0° and the delay set at 0°, measure the SPL.  
STEP 5: Rotate variable delay until the dB measurement peaks (you will know  
that it has peaked when the measurement begins to go back down). Rotate the  
knob back to the peak section.  
STEP 6: Measure angle of rotation in approximate degrees.  
STEP 7: Reset all adjustments to zero(0) / Flip phase switch to 180°  
and redo test.  
STEP 8: Your best setting is when the phase is at 180° and there is less delay.  
Specifications Are Subject To Change Without Notice  
8
 
SuperNova MKVI  
Specifications  
MODEL  
MKVI-12PIANO / BLK  
MKVI-15PIANO / BLK  
Description  
Sealed Enclosure With Patented Passive Radiator Technology  
Dimensions (HxWxD)  
16 1/4" x 15 1/2" x 19 1/2"  
73 Lbs.  
17 3/4" x 17" x 21"  
86 Lbs.  
Weight  
Frequency Response Subsonic ON  
16Hz-130Hz  
15Hz-120Hz  
Crossover at MAX  
Frequency Range  
-24dB/Oct @ below 17Hz  
120dB @ 10Hz  
-24dB/Oct @ below 15Hz  
123dB @ 10Hz  
Subsonic ON  
Subsonic OFF  
40/200Hz adjustable  
Bass Unit  
12" Cast Aluminum With Flat Piston  
12" Patented Design  
15" Cast Aluminum With Flat Piston  
15" Patented Design  
Passive Radiator  
Finish  
Multi Layer Piano Black Lacquer or Real Black Ash Wood Veneer  
Subwoofer Amplifier  
Description:  
Type: Class "J"  
Inputs: XLR / RCA, High-level  
Power Output: 600 Watts RMS  
Input Impedance: 18 kOhm (RCA)  
Signal to Noise Ratio:  
> 106dB (balanced) 105dB  
(unbalanced) @ rated power  
Functions:  
Power, Room equalization, Subsonic filter,  
Phase shift, Phase Delay, Lowpass/Bypass,  
Channel and power status LEDs,  
Dual gains internally mixed, Music sensing  
Power ON/OFF,Remote control w/ mute.  
Power Line Voltage  
110 Volts / 240 Volts AC Select Input  
Minimum Required Signal For Full Output  
One(1) RCA  
105 mV  
Two(2) RCAs'  
50 mV  
One(1) XLR  
210 mV  
Speaker Line  
2.4 V  
Gain and Crossover @ MAX  
.08 Amp (115V)  
Current Draw  
Auto OFF  
Auto ON  
.17 Amp (115V)  
7.6 Amp (115V)  
Full Output  
Specifications Are Subject To Change Without Notice  
9
 
SuperNova MKVI  
Consumer Warranty & Guidelines  
Earthquake warrants the original purchaser that all Factory Sealed  
New Audio Products be free from defects in material and workmanship, under  
normal and proper use, for a period of five (5) years from the date of purchase  
(as shown on the original bill of sale with serial number affixed/written on it). The  
five (5) years warranty period is valid only if the product is properly installed by  
an Earthquake authorized party, and the warranty registration card is properly  
filled out and sent to Earthquake Sound Corporation. If the product is installed  
by a non-authorized party, a ninety (90) days warranty period applies.  
-
-
-
Bent speaker frame, broken speaker connectors, holes in speaker  
cone, surround &dust cap, burnt speaker voice coil.  
Fading, deterioration of speaker components & finish due to improper  
exposure toelements.  
Bent amplifier casing, damaged finish on the casing due to abuse,  
misuse, or improper use of cleaning material.  
Burnt tracers on PCB.  
-
-
Product/part damaged due to poor packaging or abusive shipping  
conditions.  
(A) Five (5) years limited warranty plan coverage guidelines:  
-
Subsequent damage toother products.  
Awarranty claim will not be valid if the warranty registration card is not properly  
-
-
-
First year: Earthquake pays for labor, parts, and ground freight (only in  
US mainland, not includingAlaska and Hawaii) back tocustomer.  
Second year: Earthquake pays for labor and parts only, customer must  
pay freight both ways.  
Third, fourth & fifth year: Earthquake pays labor only. Customer must  
pay forparts and freight both ways.  
filled &returned toEarthquake with a copy of the sales invoice.  
(E) Service Request:  
To receive product/s service, contact Earthquake service department at  
(510) 732-1000 and request an RMA number (Return Material Authorization),  
items shipped without a valid RMA number will be refused. Make sure you  
provide us with your complete/correct shipping address, a valid phone number,  
and a brief description of the problem you are experiencing with the product. In  
most cases, our technicians might be able to resolve the problem over the  
phone, thus eliminating the need toship the product.  
(B) Warning:  
Products (sent for repair) that are tested by Earthquake technicians and  
deemed to have no problem, will not be covered by the five (5) years limited  
warranty. Customer will be charged a minimum of one (1) hour of labor (ongoing  
rates) plus shipping charges back tocustomer.  
(F)Shipping Instructions:  
(C) Earthquake agrees to repair or replace - at our option - all such defective  
products/parts subject tothe following provisions:  
Product/s must be packaged in its original protective box/es to minimize  
transport damage and to avoid repackaging fees. Shipper claims regarding  
items damaged in transit must be presented to carrier. Earthquake Sound  
Corporation reserves the right to refuse product improperly packed. Original bill  
of sale must accompany product returned for service. We encourage you to  
include with the package a written description of the problem. Ship product to:  
Earthquake Sound Corp. 2727 Mc ConeAvenue, Hayward, CA94545. Ph (510)  
732-1000. You are responsible for the cost of shipping the product to  
Earthquake Sound Corporation.  
-
Defective products/parts have not been altered or repaired by other  
than an Earthquake factoryapproved technician.  
-
Products/parts are not subjected to negligence, misuse, improper use,  
or accident, damaged by improper line voltage, used with incompatible  
products, or have its serial number or any part of it altered, defaced or  
removed, or have been used in any way that is contrary to Earthquake's  
written instructions.  
(G)Disputes Resolution:  
(D) Warranty Limitations:  
All disputes - between clients and Earthquake Sound Corporation -  
resulting from the five (5) years limited warranty policy must be resolved  
according tothe laws &regulations of the county ofAlameda -California.  
Earthquake warranty does not cover products that have been modified or  
abused. Including but not limited tothe following:  
-
Damages to speaker cabinet and cabinet finish due to misuse, abuse,  
or use of improper cleaning materials/methods.  
Specifications Are Subject To Change Without Notice  
10  
 
The SuperNova MKVI is capable of generating  
high sound pressure levels. You should exercise  
caution when operating this system. Long term  
S O U N D LE VE L  
D BA  
D U R ATI O N  
I N H O U R S  
CAUTION:  
90  
92  
95  
8
6
4
3
TH E CH ART (ON TH E SIDE) SH OWS TH E U.S. GOVERNM ENTS  
OCCUPATIONAL SAFETY AND H EALTH ADM INISTRATION (OSH A)  
REGULATIONS WH ICH WERE IN EFFECT AT TH E TIM E OF TH IS  
P UBLICATION FOR P ERM ISSIBLE NOISE EXP OSURE,  
P ER 29CFR1910.95, TABLE G-16.  
exposure to high levels of sound pressure will cause permanent  
damage to your hearing. Sound pressure levels exceeding  
85dB can be dangerous with constant exposure. Set your audio  
system to a comfortable loudness level. Earthquake Sound  
Corporation does not assume liability for damages resulting  
from the direct use of the MKVI , and urges users to play the  
MKVI at moderate listening levels.  
97  
2
100  
102  
105  
110  
115  
1 - 1 1/2  
1
1/2  
1/4 or less  
Specifications Are Subject To Change Without Notice  
11  
 

Echo Lawn Mower Accessory 231 User Manual
Electro Voice Music Mixer MA 1206 User Manual
Field Controls Switch GSK 250M User Manual
Fisher Price Baby Toy b1266 User Manual
Fisher Price Bouncy Seat B0772 User Manual
Fluke Weather Radio 29 User Manual
Ford Automobile 2009 Ranger User Manual
Fujitsu Printer DL9300 User Manual
Gaggenau Range EB 270 User Manual
Garmin GPS Receiver 190 00516 00 User Manual