TABLE OF CONTENTS
1. Introduction
2. Features
3. Panel Descriptions
4. Connecting and Operating the 1:5 Splitter for HDMI 1.3
5. Specifications
6. Warranty
INTRODUCTION
The Gefen 1:5 Splitter for HDMI 1.3 allows set-top boxes, DVD players, Blu-
ray players and other HDTV devices with HDMI outputs to be connected to
up to five HDTV displays (or more if multiple splitters are utilized in place of
HDTV displays
How It Works
The 1:5 Splitter for HDMI 1.3 is a distribution hub that sends the same HDMI
signals to up to five HDTV digital displays. You simply connect your HDMI
video source to the 1:5 HDMI 1.3 Splitters HDMI input jack, then connect
your HDMI-compatible displays to each of the HDMI outputs. Power-cycle
all equipment and you should see beautiful, sharp HDMI video on all of your
HDMI displays.
OPERATION NOTES
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE 1:5 SPLITTER FOR HDMI 1.3
•
Display information from the display connected to HDMI output port 1 is sent
back to the source. Therefore, all other displays connected to the 1:5 Splitter
for HDMI 1.3 must be capable of accepting the timings and resolutions of the
display that is connected to HDMI output port 1. It is recommended that the
display with the lowest native resolution be connected to HDMI output port 1.
This is to ensure that a compatible video signal will be able to be displayed
on all connected monitors.
•
•
HDMI/HDCP compliant
Compatible with all HDMI and DVI* displays
*When used with a HDMI to DVI adapter
1
FEATURES
Features
•
•
•
•
•
•
Lip-Sync Pass Through
225 MHz (up to 12 bit YUV 444 supported @ 1080p)
Deep Color Supported (XV Color Supported)
Color Space Conversion Supported
Dolby Tru-HD & DTS Master Supported
CEC Pass Through
Includes:
(1) 1:5 Splitter for HDMI 1.3
(1) 6 ft HDMI cable (m-m)
(1) 24V DC Power Supply
(1) Set of Rack Ears
(1) User’s Manual
2
PANEL DESCRIPTIONS
3
CONNECTING AND OPERATING THE 1:5 SPLITTER FOR HDMI 1.3
How to Connect the 1:5 Splitter for HDMI 1.3 to your devices
1. Connect the supplied cable from the HDTV HDMI source into the 1:5
Splitter for HDMI 1.3 input.
2. Connect the cables from your displays (monitor or projector) into the
HDMI outs of the 1:5 Splitter for HDMI 1.3.
3. Plug the 24VDC power supply into the 1:5 Splitter for HDMI 1.3.
NOTE: Display information from the display connected to HDMI output port 1 is
sent back to the source. Therefore, all other displays connected to the 1:5 Splitter
for HDMI 1.3 must be capable of accepting the timings and resolutions of the display
that is connected to HDMI output port 1. It is recommended that the display with the
lowest native resolution be connected to HDMI output port 1. This is to ensure that a
compatible video signal will be able to be displayed on all connected monitors. There is
a generic 1080i EDID programmed into the 1:5 Splitter for HDMI 1.3 that can be used
instread. Please see below for the activation process.
EDID SWITCH
The HDMI 1:5 has an EDID Switch which will determine if you are going to
use the EDID from the display attached to output 1 or use an onboard EDID.
If you want to use the EDID from the display attached to output 1, make
sure the switch is selected to "EXT".
If you want to use the onboard EDID, make sure the switch is selected to
"INT" which will give you a generic EDID of 1080i.
4
SPECIFICATIONS
Video Amplifier Bandwidth.................................................................225 MHz
Input Video Signal........................................................................1.2 volts p-p
Input DDC Signal...................................................................5 volts p-p (TTL)
Single Link Range.............................................................1080p/1920 x 1200
HDMI Connector..............................................................type A 19 pin female
Power Supply.......................................................................................24V DC
Power Consumption.................................................................60 watts (max)
Dimensions...................................................................17”W x 1.75”H x 5.5”D
Rackmountable.........................................................................1U rack space
Shipping Weight......................................................................................5 lbs.
5
|