K3799
Please keep this instruction sheet for future reference,
as it contains important information.
Requires three "D" (LR20) alkaline batteries for the mobile and
two "AA" (LR6) alkaline batteries for the remote (batteries not included).
Adult assembly required.
Tool required for assembly: Phillips screwdriver (not included).
fisher-price.com
Parts
Base
3 Soft Toys
Mobile Hub
Remote
Crib Adaptor
Clamp
Arm
3 Leaves
Note: All of the screws used to assemble this toy are attached to the product.
Follow these instructions carefully to fully secure the screws.
Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten.
3
Battery Installation
Hint: We recommend using alkaline batteries for longer battery life.
1,5V x 3
“D” (LR20)
1,5V x 2
“AA” (LR6)
Mobile Base
Remote
• Loosen the screws in mobile base battery compartment door and remove
the door.
Hint: If the crib adaptor is attached to the base, loosen the screws in the crib
adaptor and remove first.
• Insert three "D" (LR20) alkaline batteries.
• Loosen the screw in the remote battery compartment door and remove the door.
• Insert two "AA" (LR6) alkaline batteries.
• Replace each battery compartment door and tighten the screws.
Note: Under normal use conditions, the batteries in the base will require
replacement more often than the batteries in the remote. When sounds or light
become faint or movement of the mobile is sluggish, it's time for an adult to
replace the batteries in the base.
• If the mobile base begins to operate erratically, you may need to reset the
electronics. Slide the power/volume switch off and back on. If the remote
begins to operate erratically, you may need to reset the electronics. Remove the
batteries and reinstall them.
©2012 Mattel. All Rights Reserved.
PRINTED IN CHINA
K3799c-0920
4
Assembly
Crib Adaptor
Base
1
• Fit the crib adaptor to the base.
• Tighten the four screws in the crib adaptor.
Arm
ꢀPRESS
SLIDE
ꢁ
Socket
Base
2
• First press the button next to the socket
and then slide the socket
ꢀ
door open
.
ꢁ
• Fit the arm into the socket in the base.
• Tighten both screws in the arm.
5
Assembly
Mobile Hub
3
• Fit the mobile hub onto the end of the arm.
• Tighten both screws in the arm to secure the mobile hub.
Hint: You may want to attach the soft toys to the mobile hub before assembling
the arm to the mobile hub. Please refer to assembly step 5 for instructions to
assemble the soft toys.
6
Assembly
Leaves
4
• “Snap” the leaves into the slots in the mobile hub.
5
Soft Toys
• Fit the soft toys to the pegs on the underside of the mobile hub.
• Tighten the screw in each toy to secure each to the mobile hub.
7
Crib Attachment
Crib Top Rail
Base
Clamp
• Fit the base onto the crib top rail, so that the threaded peg extends outside
the crib.
• Fit the clamp onto the threaded peg and turn the clamp clockwise to secure the
base to the crib. Do not over-tighten the clamp.
Bottom
of Base
Mattress
At least 7 inches
(18 cm)
• If the distance between the bottom of the base and the mattress is less than
7 inches (18 cm), lower the crib mattress.
8
Remote Use
• Press the button on the remote to activate music, lights and motion.
• Press again to stop.
• In the unlikely event that use of the remote interferes with normal use
of other remote controlled equiment, such as televisions or stereos, or use of
other electronic or battery powered appliances interfere with operation of the
mobile, do not use both at the same time.
• You may notice a loss of range between the remote and the mobile when using
in bright light. For best performance, avoid using the remote in areas of bright
light. Move the mobile, or reduce the amount of light to improve performance.
• Position the mobile so that the receiver arrow points towards the area that the
remote will be used. Make sure there is a clear path between the remote and
the mobile. Point the end of the remote toward the mobile receiver and
press the button.
Note: The remote will remain active for about one hour. Slide the power/volume
switch on the mobile off, then on again to reactivate.
9
|