EVERFOCUS
1/3” 560 TVL Color Mini Dome Camera
Operation Instructions
Model No. ED350
Please read this manual first for correct installation and operation. This manual should be retained
for future reference. The information in this manual was current when published. The
manufacturer reserves the right to revise and improve its products. All specifications are therefore
subject to change without notice.
PRECAUTIONS
1. Do not install the camera near electric or magnetic fields.
Install the camera away from TV, radio transmitter, magnet, electric motor, transformer,
audio speakers since the magnetic fields generate from above devices will distort the video
images.
2. Never disassemble the camera nor put impurities in it.
Disassembly or impurities may result in trouble or fire.
3. Never face the camera toward the sun.
Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit.
4. Keep the power cord away from water and liquid.
Touching the wet power cord may result in electric shock.
5. Never install the camera in areas exposed to water, oil or gas.
Water, oil or gas may result in failure, electric shock or fire.
SPECIFICATIONS
Pickup Device
Video Format
1/3'' SONY Super HAD CCD
NTSC or PAL
NTSC: 525 TV lines, 60 fields/sec
PAL: 625 TV lines, 50 fields/sec
768 x 494(NTSC) ; 752 x 582(PAL)
560TVL
Scanning System
Picture Elements
Horizontal Resolution
Sensitivity
0.5Lux/F=1.2
S/N Ratio
Over 48dB(AGC off)
1/50(1/60)~1/100,000
Vari-focal lens, Auto Iris
f=2.9~10mm, F=1.2
Electronic Shutter
Lens Type
f=3.8~9.5mm, F=1.2
f=9~22mm. F=1.6
*Lens models and availability vary in different regions
ON/OFF Switch
Back Light Comp.
Auto Gain Control
Flickerless
ON/OFF Switch
ON/OFF Switch
Auto White Balance
Gamma Correction
Yes
0.45
2 video outputs
Video Output
BNC 1.0Vp-p, 75ohm
Additional testing video output 1.0Vp-p, 75ohm
Internal Sync
Sync. Mode
Power Source
12VDC/24VAC
24VAC: 5VA max
Power Consumption
12VDC: 3.5W max
Dimensions
108(O.D.) x 80(H) mm ; 4.3"(O.D.) x 3.2"(H)
0.3 kg ; 0.7lbs
Weight
Operating Temperature
Certifications
0°C~40°C ; 32°F~104°F (20%~80% Humidity)
FCC/CE
2
DIMENSIONS
MAJOR PARTS NAME & THEIR FUNCTIONS
c
d
f
g
e
6
7
3
(1) Camera Cover
This cover will protect the camera from dust and damage.
(2) Lens
This Vari-Focal Lens allows users to adjust the Zoom and Focus manually.
(3) Base
The camera unit is set in the dome base when it is shipped from the factory.
(4) Focus Ring
To set the focus, loosen the Focus ring knob first, then turn the ring toward <∞> or <N> as
necessary. When the focus is obtained as desired, tighten the focus ring knob.
(5) Zoom Ring
Loosen the zoom ring knob, then you can adjust the viewing range. Turn the ring towards <W>
for WIDE or <T> for TELE as necessary. When the setting is finished, tighten the zoom ring
knob.
(6) Power input
Use the connector to connect with 12VDC/24VAC power adaptor.
(7) Video Output BNC Connector
Use the connector to connect with the video in connector of a monitor.
4
LENS ADJUSTMENT
Zoom and focus adjustments
After the camera was installed, the zoom and focus of the
lens must be adjusted.
1. Loosen the zoom ring knob, and then turn the ring
towards <W> or <T> as necessary to obtain the
desired view range.
W side (Zoom out)
The viewing range will be wider and the subject is
smaller.
T side (Zoom in)
The viewing range will be smaller and the subject is larger.
2. Loosen the focus ring knob, then turn the ring towards <∞> or <N> as necessary to obtain
the clear video image.
3. Repeat steps 1 and 2 until the best image is obtained. Once the lens setting finished, tighten
the zoom ring and the focus ring knobs.
5
ADJUSTMENTS
5
3
4
1
2
6
(1) IRIS ALC Adjustment
To select light metering method:
„ Turn the IRIS ALC Adjustment VR counterclockwise for Average Metering.
„ Turn the IRIS ALC Adjustment VR clockwise for Peak Metering.
(2) IRIS Level Adjustment
Brightness Level can be adjusted from the IRIS level VR while using the direct drive lens.
„ Turn counterclockwise to L to get darker picture.
„ Turn clockwise to H to get brighter picture.
6
(3) Flickerless
When picture flicker fiercely, turn FL on, then the camera will stabilize the speed
of electronic shutter at 1/100(NTSC) or 1/120(PAL) automatically, and reduce the
flicker immediately.
The default setting is OFF.
(4) Auto Gain Control Adjustment
AGC ON: The sensitivity increases automatically when the light is low.
AGC OFF: A low-noise picture is obtained under a low light condition.
(5) Back Light Compensation Adjustment
When the background of the subject is very bright and the subject itself is dark, set
the BLC (Back Light Compensation) ON. The BLC will measure the light of the
image center and the lens iris will automatically set for optimum image quality.
(6) Ground Pin
For monitor use. When setting up the camera, connect a monitor to this video output pin
and to the GROUND pin using alligator clip cables, then use the image displayed on the
monitor, set the surveillance angle.
7
INSTALLATION
1. Remove the plastic dome cover.
2. Lossen the two screws of the supporting bracket to remove the camera body.
3. Use four screws to fix the camera base on the ceiling.
4. Put the camera body back to the supporting bracket, then tighten the two screws to
fix the camera.
5. Connect the BNC connector of the camera to a color monitor, or other video
device through a 75 ohm type coaxial cable with BNC female connector at cable
extension.
6. Connect the 12VDC/24VAC regulated power source of the camera.
7. Connect the audio output connector of the camera (model High Resolution Dome
A) to the audio in connector of the monitor.
NOTE: Be very careful not to scratch or damage the lens while making any kind of setting.
8
EverFocus Electronics Corp.
Europe Office:
Head Office:
Albert-Einstein-Strasse 1
D-46446 Emmerich, Germany
TEL: 49-2822-9394-0
12F, No.79 Sec. 1 Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: +886-2-26982334
FAX: +886-2-26982380
China Office:
Room B-05D-1, KESHI PLAZA , Shangdi
Information Industry Base,
USA L.A. Office:
1801 Highland Ave. Unit A
Duarte, CA 91010, U.S.A.
TEL: +1-626-844-8888
FAX: +1-626-844-8838
Haidian District, Beijing China
100085
TEL: +86-10-62973336/37/38/39
FAX: +86-10-62971423
USA N.Y. Office:
Japan Office:
415 Oser Avenue Unit S
Hauppauge, NY 11788
TEL: 631-436-5070
FAX: 631-436-5027
1809 WBG MARIBU East 18F,
2-6 Nakase.Mihama-ku.
Chiba city 261-7118, Japan
TEL: +81-43-212-8188
FAX: +81-43-297-0081
Your EverFocus product is designed and
manufactured with high quality materials and
components which can be recycled and
reused.
Ihr EverFocus Produkt wurde entwickelt und
hergestellt mit qualitativ hochwertigen
Materialien und Komponenten, die recycelt
und wieder verwendet werden können.
Dieses Symbol bedeutet, dass elektrische und
elektronische Geräte am Ende ihrer
Nutzungsdauer vom Hausmüll getrennt
entsorgt werden sollen.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed of separately from your
household waste.
Please, dispose of this equipment at your
local community waste collection/recycling
centre.
Bitte entsorgen Sie dieses Gerät bei Ihrer
örtlichen kommunalen Sammelstelle oder im
Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu erhalten, in
der wir leben!
In the European Union there are separate
collection systems for used electrical and
electronic product.
Please, help us to conserve the environment
we live in!
P/N: MED3G03000_Ver.B
9
|