Earlex Paint Sprayer V0053 User Manual

5) Fitting of Straps to Spray Pack:  
i. Fit the strap hooks into the round holes at the top  
of the Spray Pack.  
ii. Feed the strap through the vertical slots at the  
bottom of the Spray Pack, loop around and feed  
back through the strap buckle.  
Spray Pack  
PLEASE READ MAIN INSTRUCTION MANUAL  
BEFORE USE  
Spraying  
IT IS RECOMMENDED THAT THE UNIT IS TESTED WITH  
WATER PRIOR TO EACH USE  
1. Remove Spray Pack Lid (2) and pour in required  
spray material and thinners.  
2. Ensure the spray material and thinners do not  
exceed the max fill line on the Spray Pack.  
3. Fit the Spray Pack Lid, ensuring that Seal (3) is  
present. Make sure the lid is tightened securely.  
4. Connect the hose that is supplied with your Earlex  
Spray Station into the back of the Spray Gun.  
5. Put the Spray Pack on your back and tighten straps  
(WARNING: Spray Pack weighs approximately 5kg  
when full).  
6. Ensure the Spray Pack is secure on your back and  
the straps are tightened. The Spray Pack should sit  
in your upper back area for optimum working  
spray height.  
Important Information  
This Spray Pack is only to be used with the following  
Earlex HVLP units, Spray Station 2900, 3500 and 3900.  
Using with another HVLP unit may affect the Spray  
Pack’s performance. This does not affect your  
statutory rights.  
This 4 litre Spray Pack is designed to fit your back. It  
allows for large painting jobs to be completed without  
the need to re-fill, saving you a substantial amount of  
time. There are jobs where the use of the 1 litre  
container is more appropriate:  
7. Turn on the Spray Station unit, hold the Spray Gun  
lower than Spray Pack until the liquid reaches the  
Spray Gun, then you are ready to start spraying.  
Overalls, goggles, mask and gloves should be worn  
whilst using spray equipment.  
Which Container  
should I use?  
4litre Spray Pack  
1litre  
Container  
For ceiling  
Not recommended  
Yes  
Yes  
Yes  
For wall or floor  
With water based  
product  
Yes  
Yes  
Cleaning Instructions  
The Spray Pack must be thoroughly cleaned  
immediately after use. If the paint dries inside the  
Spray Pack, cleaning will become much more  
difficult and may render the Spray Pack inoperable.  
This is not covered by the guarantee.  
With solvent based Not recommended as  
Yes  
a lot of thinners will be  
required for the clean  
up  
product  
Yes  
Yes  
Undercoats  
Not recommended  
Smooth masonry  
paints  
Not recommended  
• Remove the Spray Pack Lid (2).  
• Pour any leftover paint into a container so that it  
can be used in the future. Wipe the Spray Pack to  
remove as much as possible.  
NB: As per the use of the 1 litre container, low  
• Pour a quantity of thinners or water into the  
container, shake the Spray Pack lightly, reassemble  
the Spray Pack, then spray this liquid through the  
Spray Gun. Repeat this process until the thinner  
being sprayed is coming through with no traces of  
paint.  
temperatures can make paint thicker and we therefore  
recommend spraying at a minimum of 15°C.  
THE SPRAY PACK MUST BE  
ASSEMBLED BEFORE FILLING  
• Clean any traces of paint off the outside of the  
Spray Gun.  
Set Up for HV2900, 3500 or 3900  
(Fig.1)  
Troubleshooting  
1) Using scissors or a sharp knife, split the Twin Tube (5)  
at both ends.  
2) Put the Hose Clips (6) at each end of the striped  
tube (Fig.2).  
3) Take the Spray Gun and remove the Paint  
Container and Pick-Up Tube.  
PROBLEM  
WHAT IS THE SOLUTION?  
Spray material 1. Check Air feed Hose and Spray Pack  
does not reach Container lid are sealed and fully tightened.  
Spray Gun  
2. Check if Spray Gun Fluid Tip is blocked  
4) Connect the striped tube to the bottom of the  
Spray Pack (Fig.2, 1a) and the other end to the  
paint pick up (Fig.2, 1b) of the Spray Gun, and  
connect the unstriped tube to the top of the Spray  
Pack (Fig.2, 2a) and the other end to the air outlet  
on the Spray Gun (Fig.2, 2b).  
when trigger is and Fluid Needle is free to move.  
activated  
3. Check the dilution of your paint and if  
necessary dilute more.  
4. Level of spray material in container is  
too low, refill.  
HINT: Running the end of the tubes under warm  
water will ease the fitting onto the Spray Gun and  
Spray Pack.  
Design Registrations;  
GB 3022948 FR 06/5462 US D562,544 CA 118106  
V0053 07/09  
 

Craftsman Tiller 91729332 User Manual
Dell Server 35XX User Manual
Dynacord Speaker DL 800 10T User Manual
Escient Stereo Receiver AVX User Manual
EverFocus Camera Accessories EDH5102 User Manual
Fisher Paykel Oven OD301 User Manual
Garmin Clock v10b User Manual
GE Answering Machine TAD 732 User Manual
GE Monogram Video Games ZDBC240NBS User Manual
Global Machinery Company Power Screwdriver FQC54V User Manual