DX-32L100A11_10-1117_QSG_V1_EEN.eps
1
9/29//2010
10:000:24 AM
V1
FINAL
FOR PRINT
Front and side features
Connecting a DVD or Blu-ray DVD player, cable
box, satellite receiver or game station
Using HDMI (best)
Connecting a home theater system
Using analog audio cable:
Back of TV
Back of TV
L
L
AUDIO
AUDIO
R
R
ANT/ CABLE IN
AUDIO OUT
AUDIO
VGA
ANT/ CABLE IN
AUDIO OUT
L
L
AUDIO
AUDIO
R
R
Y
P
B
PR
AUDIO
VGA
DIGITAL OUTPUT HDMI 1
PC IN
COMPONENT IN
Y
P
B
PR
DIGITAL OUTPUT HDMI 1
PC IN
COMPONENT IN
32" LCD TV
QUICK SETUP GUIDE
Remote control Power
sensor indicator
DX-32L100A11
Audio
cable
Audio amplifier
Installing the stand
1 Remove the stand from the box and place it on a table or bench.
2 Lay the TV flat (screen down) on a flat, cushioned surface.
3 Align the stand with the TV, as shown.
HDMI device
Note: Cable connectors and jacks are often color-coded. Match the colors when
HDMI cable
(not included)
you connect the AV cable.
Using digital audio cable:
Using component (better)
Back of TV
Back of TV
ANT/ CABLE IN
AUDIO OUT
L
L
AUDIO
AUDIO
R
R
Table
Stand
edge
AUDIO
VGA
Y
P
B
PR
L
L
AUDIO
AUDIO
R
R
ANT/ CABLE IN
AUDIO OUT
DIGITAL OUTPUT HDMI 1
PC IN
COMPONENT IN
AUDIO
VGA
column
Y
P
B
PR
DIGITAL OUTPUT HDMI 1
PC IN
COMPONENT IN
Stand
Remote control
and
AC power cord
4 Secure the stand to the column with the screws provided
2 AAA batteries
Component video device
Digital optical cable
Digital sound
system
Component
audio cable
(not included)
Component
video cable
Note: The DIGITAL OUTPUT jack only works with digital TV channels.
TV stand and screws
Connecting power
Table
edge
Connect the power cable to the AC IN jack on the back of the TV, then connect
the other end to a power outlet.
Connecting an antenna
Connect a 75 ohm cable (not included) to ANT/CABLE IN jack on the back of
your TV and the RF OUT jack on the antenna.
Installing a wall-mount bracket
1 Carefully place your TV screen face-down on a cushioned, clean surface to
protect the screen from damages and scratches.
Power cord
2 Remove the four screws holding the TV to its stand column, then remove the
stand column.
3 Secure the wall-mount bracket (not included) to the back of your TV using the
four M6 screws provided with the bracket.
Power outlet
Back of TV
L
L
AUDIO
AUDIO
R
R
ANT/ CABLE IN
AUDIO OUT
AUDIO
VGA
Y
P
B
PR
DIGITAL OUTPUT HDMI 1
PC IN
COMPONENT IN
Setting up your remote control
1 While pressing the release button on the battery compartment cover on the
back of the remote, lift the cover off the remote.
75-Ohm coaxial
cable
2 Insert two AAA batteries into the battery compartment. Make sure that the +
and – symbols on the batteries align with the + and – symbols in the battery
compartment.
Quick Setup Guide
3 Replace the cover.
To program your existing remote control to work with your Dynex TV, see the
table below for common codes. If you have problems programming your
for the latest remote control code information.
Universal remote control TV codes (for all Dynex TVs manufactured after Jan. 1, 2007)
Universal remote control makers and models
Set-top box makers and models
Philips
PHDVD5, PH5DSS,
PMDVR8, PDVR8
RCA
RCU807
One for All
URC-6690
Sony
RM-VL600
Comcast
M1057
Dish Network
VIP508, VIP622
Motorola
DRC800
TIVO
Series 3, HD
DirectTV
RC23
115
135
0464
8043
0463
720
0463
0091
10463
|