XHD7714
INSTALLATION/OWNER'SꢀMANUAL
®
®
®
AM/FM/CD/MP3/WMA/USB/3.5mm/iPod /Bluetooth /HDꢀRadio™/iTunes ꢀTaggingꢀ
ReceiverꢀwithꢀDetachableꢀFace
XHD7714ꢀINSTALLATIONꢀ
WiringꢀDiagram
RCA Connections
Right Channel (Red)
Left Channel (White)
REAR
FRONT
SUBWOOFER
FRONT
SUB/W
L-CH
R-CH
REMOTE IN
Antenna
Connector
Steering Wheel Interface Input
(PAC SWI-PS required)
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The XHD7714 uses one
10 amp ATM fuse located
beside the wiring connector.
3
XHD7714ꢀOPERATIONꢀ
ControlꢀLocationsꢀ-ꢀReceiver
6
9
8
10 11
2
3
4
5
7
1
20
17
16
15 14
13
12
22
19
18
21
USB Port
Open
Talk
1
12
13
14
15
16
17
18
19
20
21
22
Preset 6/Folder Up
Preset 5/Folder Down
Display
2
3
Mute/End Call
Tune/Track Down
Power ( )/Select
Tune/Track Up
Preset 1/Repeat
Preset 3/Intro
4
Volume
5
Mode/EQ
6
Bluetooth Microphone
Band/ESC
7
8
9
Audio/Menu
Scan/HD Seek
Tag
Preset 2/Random
10
Preset 4/Play/Pause
Auxiliary Input
11
The XHD7714 allows playback of your favorite MP3 and WMA files recorded on CD-R and
CD-RW discs. Its powerful on-board DSP processor decodes the compressed audio while
maintaining near-CD sound quality. An internal SRAM buffer provides ESP (Electronic
Skip Protection) to virtually eliminate skipping and allows alphanumeric or direct track
search - even while a song is currently playing!
4
XHD7714ꢀOPERATION
ControlꢀLocationsꢀ-ꢀRemote
2
3
1
4
5
21
20
19
18
6
7
8
9
10
17
16
11
12
15
14
13
Mode/EQ
12 Key 9
1
2
13
14
15
16
17
18
19
Mute/End Call
Display/Key 0
Talk
Power( )/Select
Volume Up
3
4
Audio/Menu
Key 8/Tag
5
Tune/Track Up
Volume Down
Key 7
6
Preset 4/Play/Pause
Preset 1/Repeat
Band/ESC/* Key
Tune/Track Down
7
Scan/PS/# Key
Preset 3/Intro
8
9
20
21
Preset 2/Random
Preset 6/Folder Up
Preset 5/Folder Down
10
11
5
XHD7714ꢀOPERATION
GeneralꢀOperation
Press OPEN to fold down the front panel, then pull away
FaceplateꢀRemoval
from the bottom to remove. To re-install, slide in the right
side of the bottom of the front panel first, then snap the left
side into place and fold up.
Remove trim ring and install two supplied #1 x 7/32” Phillips
head screws through both of mounting frame into faceplate.
Semi-Permanentꢀ
FaceplateꢀInstallation
Press or any other button to turn the unit on. Press and
PowerꢀOn/Off
hold to turn the unit off.
ꢀ
Mode
Press MODE to select between AM/FM, CD player, USB,
auxiliary input, iPod and Bluetooth. Modes of operation are
indicated in the display.
Note: CD, USB and iPod modes will not appear unless a CD,
USB device or iPod are inserted.
Insert a 3.5mm connector in the front panel AUX port.
Connect the other end of the 3.5mm connector to the
headphone output of an audio device, MP3 player, etc. Press
MODE to select AUX mode.
AuxiliaryꢀInput
The steering wheel interface input located on the back of
the head unit allows connection to the PacificꢀAccessoryꢀ
CorporationꢀSWI-PS interface module (sold separately). Visit
SteeringꢀWheelꢀ
InputꢀInterface
To configure steering wheel controls, follow the instructions
provided with the PACꢀSWI-PS interface module. After
installing the interface module, insert the module's 3.5mm
jack into the port on the back of the head unit.
Volume
Mute
Adjust volume using volume knob (00-46).
Press ꢀꢀꢀꢀ to silence the audio. “MUTE” will flash in the
display. Press ꢀꢀꢀ again to cancel.
PresetꢀEQꢀCurves
Press and hold EQꢀfor 3 secondsꢀto enter EQ setup menu,
then use the volume knob to select between POP, JAZZ,
CLASSIC, BEAT, ROCK and FLAT (default) equalization
curves. Any adjustment to the Bass or Treble settings
automatically cancels the current EQ curve (if one is
selected).
Display
Press DISP to select between clock and different types of
information, such as radio frequency, CD track or MP3/USB
song information.
SetꢀtheꢀClock
With the unit on, press and hold DISP until the clock begins
to flash, then release. Press TUNE
to adjust the
nn
hours and TUNEꢀ
to adjust the minutes. Press DISP
ll
momentarily to save the selected time.
Reset
Press to RESET the unit upon initial installation or if
abnormal operation occurs. Reset button is located behind
the faceplate.
6
XHD7714ꢀOPERATION
GeneralꢀOperation
Press and hold AUD•MENU for more than 3 seconds to access
the setup menu, then press AUD•MENU to cycle through menu
options. When desired option appears in the display, rotate the
volumeꢀknob left/right to adjust or activate the desired function.
Press ESC to exit the menu at any time.
SetupꢀMenu
SetupꢀMenu
MenuꢀFunction
Options
Action
AutoꢀStationꢀ
Store
AUTO
STORE
Press SELECT to save 6 strong stations in the current band. Note: This
option only appears in Tuner mode.
DeleteꢀSavedꢀ
iTunesꢀTags
DELETE
TAGS
Press SELECT to delete any iTunes Tags that are currently saved. Note:
This option only appears in Tuner mode.
TUNER DIGITAL
Programs the unit to tune to digital and analog radio stations. Note: This
option only appears in Tuner mode.
TuningꢀMode
TUNER ANALOG Programs the unit to tune to analog radio stations only. Note: This option
only appears in Tuner mode.
LOUD OFF
LOUD ON
Disables the loudness function.
Loudnessꢀ
Curve
Enables the loudness function. Activating this feature will enhance the
bass and treble frequencies when listening to music at low volumes.
CLOCK OFF
CLOCK ON
AUX ON
Programs unit to not display the clock when the power is off.
Programs unit to display the clock when the power is off.
Enables the front panel 3.5mm auxiliary input.
Disables the auxiliary input.
Clockꢀ
Display
Auxiliaryꢀ
Input
AUX OFF
BEEP OFF
BEEP ON
Disables the confirmation beep.
Beepꢀ
Confirmation
Enables the confirmation beep.
PRO-VOL OFF
Programs the unit to turn on with the same volume as it was powered
off with.
Programmableꢀ
TurnꢀOnꢀVolume
PRO-VOL (1-46)
Use the volume knob to select a volume between 1 and 46. The XHD7714
will always turn on to this selected volume.
LOCAL OFF
Activates distance tuning.
Local/Distanceꢀ
Tuning
LOCAL ON
Activates local tuning for strong station reception only.
Disables power on message. Example: "GOOD MORNING"
Enables power on message to be displayed.
MESSAGE OFF
MESSAGE ON
SCROLL ONCE
Powerꢀonꢀ
Message
Programs unit to scroll once, then show the first 10 characters on the
display.
Scrollingꢀ
Option
SCROLL ON
SCROLL OFF
DIMMER HIGH
Programs unit to scroll continuously.
Programs unit to show the first 10 characters on the display.
Programs unit to the brightest illumination level.
Illuminationꢀ
Dimmer
DIMMER MEDIUM Programs unit to the middle illumination level.
DIMMER LOW
DEMO OFF
DEMO ON
Programs unit to the dimmest illumination level.
Disables the demonstration mode.
Demonstrationꢀ
Mode
Enables the demonstration mode message.
Note: Refer to page 27 for Bluetooth setup menu options.
7
XHD7714ꢀOPERATION
GeneralꢀOperation
Press ESC to exit any menu adjustment mode.
Escape
Press AUD•MENU momentarily to select between Volume
(default), Bass, Treble, Balance, Fader, Subwoofer and
Source Volume Level.
Audio
VOLUME
BASS
TREBLE
BALANCE
FADER
SUBWOOFER
SOURCE LEVEL
Press AUD•MENU until BASS appears, then press SELECTꢀ
to confirm. Rotate volume left/right to adjust (-6 minimum /
+6 maximum).
Bass
Press AUD•MENU until TREBLE appears, then press
SELECTꢀto confirm. Rotate volume left/right to adjust ( -6
minimum / +6 maximum).
Treble
Note:ꢀAny adjustment to the Bass or Treble settings
automatically cancels the current EQ curve (if one is
selected).
Note: Bass and Treble settings are retained for each mode
individually.
Press AUD•MENU until BALANCE appears, then press
SELECTꢀto confirm. Rotate volume left/right to adjust (BAL L
12-BAL 00-BAL R 12). BAL 00 represents equal balance.
Balance
Fader
Press AUD•MENU until FADER appears, then press SELECTꢀ
to confirm. Rotate volume left/right to adjust (FAD F 12-FAD
00-FAD R 12). FAD 00 represents equal fader.
Press AUD•MENU until SUB-W appears, then press
SELECTꢀto confirm. Rotate volume left/right to adjust (0-12).
Adjusting levels to 0 turns the subwoofer off.
Subwoofer
The source volume level control allows a gain adjustment
for each audio source: AM, FM, CD, AUX, USB and Bluetooth.
Set the source volume level for each mode, depending on
the relative volume of each audio source.
SourceꢀVolumeꢀLevel
To set the source volume level, press AUD•MENU until
SOURCE LEVEL appears. After one second, the current
mode will appear on the display. Turn the volume knob to
adjust the audio level of the current source (-6 minimum/+6
maximum).
Note:ꢀOnly the current mode will be available for adjustment.
To adjust another mode of operation, press MODE until the
desired mode is selected, then set the source volume level
for that mode.
8
XHD7714ꢀOPERATION
HDꢀRadio™ꢀAM/FMꢀTunerꢀOperation
The following tuning functions will access both analog and
digital stations. Refer to the HDꢀSEEKꢀmodeꢀsection on page
10 for instructions on tuning to only digital stations.
AnalogꢀandꢀDigitalꢀTuning
Press TUNE
seek the next strong station.
or TUNEꢀ
for more than one second to
SeekꢀTuning
nn
ll
When an HD Radio station is selected, an HD Radio logo will
begin to flash on the display. In about five seconds, HD or
HD1 will illuminate after the radio frequency.
• If "HD" appears, the radio station is broadcasting a higher
quality sound. No additional stations are available.
•
If "HD1" appears, additional multicast channels (HD2
and/or HD3) are available. Press TUNEꢀllto tune to
other available multicast channels.
Press TUNE
frequency up or down one step at a time.
or TUNEꢀ
momentarily to move radio
ManualꢀTuning
ScanꢀTuning
nn
ll
Press SCN momentarily to preview strong stations on the
current band, pausing for five seconds at each. Press SCN
again to cancel.
Bandꢀ
Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands. Up to six presets can be programmed for each
band.
StoringꢀandꢀRecallingꢀ
StationꢀPresets
Up to 18 FM stations and 12 AM stations can be stored.
including HD Radio stations and multicast channels. To store
a station, select the desired band and station. Press and hold
the desired preset button (1-6) for more than two seconds.
When stored, the preset number will appear in the display.
The station can be recalled by pressing the corresponding
preset button.
9
XHD7714ꢀOPERATIONꢀ
HDꢀRadio™ꢀAM/FMꢀTunerꢀOperation
ꢀDisplay When the unit is tuned to an analog station, press DISP to
toggle the display between the following options:
(LINE 1)
(LINE 2)
FREQUENCY
BAND/PRESET
FREQUENCY
CLOCK
When the unit is tuned to an HD Radio station, press DISP to
toggle the display between the following options:
(LINE 1)
(LINE 2)
ARTIST
SONG TITLE
STATION NAME
PROGRAM TYPE
FREQUENCY
CLOCK
When information is unavailable, "NO DATA" appears in the
display.
Press and hold HDꢀSEEK for 3 seconds to activate digital-
only tuning mode. The HDꢀSEEK icon will appear on the
display, indicating that the unit will skip over analog stations
and tune to HD Radio stations only. Follow the instructions
on page 9 to access seek, manual and scan tuning.
HDꢀSeekꢀMode
•ꢀꢀStoringꢀandꢀRecallingꢀStationꢀPresets
HD Radio multicast stations (HD2 and HD3) can also
be stored as presets. When a preset multicast station
is recalled, "LINKING" appears in the display until the
download process is complete (approximately 5 seconds).
ꢀ
Note: If the HD Radio signal on the preset is unavailable,
the unit reverts to the previous analog or digital station.
• AutomaticallyꢀStoreꢀOnlyꢀHDꢀRadioꢀStations
While in HD SEEK mode, press and hold AUD•MENU to
enter the setup menu. Choose the AUTO STORE menu
option and press SELECT to begin automatically storing
the first 6 HD Radio stations to presets 1-6.
Note: Since all HD Radio stations that blend to digital are
considered 'strong' stations, the Auto Station Store feature
will store the first 6 HD Radio stations, beginning from the
lowest frequency. Multicast channels (HD2 and/or HD3) are
not automatically stored with this feature, but can be stored
by holding the desired preset number (1-6) for 3 seconds.
10
XHD7714ꢀOPERATIONꢀ
iTunes®ꢀTagging
Overview
The iTunes Tagging feature of the XHD7714 allows the user
to "Tag" songs that are playing on HD Radio™ stations and
enables them to be purchased later through iTunes®. With
the touch of a button the unit will remember the title and
artist song information, and then transfer that information
to your iPod® the next time you connect it to the XHD7714
using the supplied 2-wire cable. A new list called "Tagged"
will appear in iTunes, giving you the option to purchase each
song.
TaggingꢀMusic
Stepꢀ1
Tune to an HD Radio station. The HD logo in the display
must light up solid - indicating that a digital station is tuned.
If the song has valid artist and song title information, the
TAG button will turn red.
Stepꢀ2
Stepꢀ3
Press the TAG button. SONG TAGGED will appear in the
display, followed by the current number of Tags in memory.
The song information will be saved in memory until an iPod
is plugged in. Up to 127 Tags can be saved before they must
be transferred to an iPod, or deleted.
Plug in an iPod. The current Tags in memory will be
automatically transferred to the iPod and the Tags will be
deleted from the head unit's memory.
If an iPod is plugged in when a song is tagged, the Tag will
be immediately transferred to the iPod. (see page 12 for
iPod compatibility)
Stepꢀ4
Sync with iTunes. A list named "Tagged" will appear on the
left in the iTunes software. Click on the "Tagged" list to view
all the songs that have been tagged and click the "view"
button for purchase information.
ViewingꢀTagsꢀinꢀMemory
DeletingꢀAllꢀTags
To view the current number of saved Tags in memory, press
and hold TAG for 3 seconds. The current number of saved
Tags will appear along with the total (127).
To delete all the saved tags without transferring them to
an iPod, press AUD•MENU for 3 seconds to enter the setup
menu from tuner mode. Rotate the volume knob until
DELETE TAGS appears, then press SELECT. A confirmation
message will appear.
Note: Tags that are saved on an iPod can be managed from
the iTunes software.
11
XHD7714ꢀOPERATIONꢀ
iTunes®ꢀTagging
Below is a list of messages that may be displayed when using the
iTunes Tagging feature with an explanation of the message.
Description
Displayed Message
There is a compatibility issue with the iPod® that is connected.
Check the list of compatible iPods below.
CHECKꢀIPODꢀVER
If the attached iPod is compatible, update the firmware to the
latest version using iTunes®.
The XHD7714 is sending Tags to the iPod. This process can take
several minutes depending on the number of Tags being sent.
The unit must be in Tuner mode to complete this process.
SENDINGꢀTAGS
IPODꢀFULL
There is not enough space on the connected iPod to transfer the
iTunes Tags. Free up space on the iPod.
There was a connection error while the head unit was sending
TRANSFERꢀFAILED iTunes Tags to the iPod. Ensure the iPod is powered on and
reconnect the iPod until a TAGS SENT confirmation is displayed.
The same song has already been tagged from the same radio
station, and is currently saved in memory. The same song cannot
be tagged twice, unless the song is tagged on a different radio
ALREADYꢀTAGGED
station, the Tags are sent to an iPod or the tags are erased.
The internal memory of the XHD7714 will hold 127 Tags. An iPod
MEMORYꢀFULL
must be connected to transfer the Tags, or the Tags must be
CONNECTꢀIPOD
deleted before more songs can be tagged.
There is not sufficient information (artist or title) to tag the song.
NOꢀTAGꢀINFO
Some HD Radio™ stations or certain songs may not fully support
iTunes Tagging.
There was an error saving the Tag information to the internal
memory. Press theꢀTAG button again.
TAGGINGꢀFAILED
There are no tags saved in the interal memory. The DELETE
NOꢀTAGSꢀSTORED TAGS function can only delete Tags that are saved in the internal
memory.
iPodꢀCompatibility The following models support iTunes Tagging
withꢀiTunesꢀTagging • Fifth generation iPod
• Third generation iPod Nano
• iPod Classic
12
XHD7714ꢀOPERATIONꢀ
CDꢀPlayerꢀOperation
Press OPEN to fold down the front panel and expose the CD
slot. Then with the label facing up, insert a standard size CD
into the CD slot.
InsertꢀCD
EjectꢀCD
Press OPEN to fold down the front panel and expose the
button. Press ꢀto eject the CD. The unit will change
to previous mode of operation (AM/FM, USB, iPod, AUX or
Bluetooth). If the disc is not removed within 10 seconds, the
unit will reload the disc. The unit does not have to be turned
on to eject CD.
Press TRACKꢀ
to skip to the beginning of the next
TrackꢀSelect
ll
track. Press TRACK
to return to the beginning of the
nn
current track. Pressing TRACK
beginning of the previous track.
again skips to the
nn
Press and hold TRACKꢀ
or reverse a track.
or TRACK
to fast forward
FastꢀForwardꢀandꢀReverse
ll
nn
Press
Press
/
/
II to temporarily stop CD playback.
II again to resume playback.
Pause
l
l
Press RPTꢀto enter the Repeat menu, then turn the volume
knob to select one of the following options:
• ALL - Continuously repeats the entire disc.
• TRACK - Continuously repeats selected track.
Repeat
Press RDMꢀto enter the Random menu, then turn the
volume knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
Random
• ALL- Plays all tracks in random order.
Note: Random mode is retained in memory when selecting
between AM/FM, CD, iPod, USB, AUX and Bluetooth modes
and when the unit is turned on/off.
Press INTꢀto enter the Intro menu, then turn the volume
knob to select one of the following options:
• OFF - Cancels the INTꢀfunction.
Intro
• ALL - Plays the first 10 seconds of each track.
Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method.
In addition, the following CDs may be incompatible with
this unit: CDs exposed to extreme temperatures or direct
sunlight for extended periods of time, CDs recorded in
which a recording session failed or a re-recording was
attempted and encrypted or copy-protected CDs that do not
conform to the audio CD-DA red book recording standard.
CD-R/CD-RWꢀCompatibility
13
XHD7714ꢀOPERATIONꢀ
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
PlayingꢀanꢀMP3/WMAꢀDisc
When an MP3/WMA encoded disc is first inserted,
“READING” will appear in the display. Depending on the
number of files and folders, this may take several seconds.
DisplayingꢀInformation
Press DISP to toggle between the following song
information options:
(LINE 1)
(LINE 2)
ARTIST
SONG TITLE
ELAPSED TIME
CLOCK
TRACK NUMBER
TOTAL TRACKS
FILE NAME
FOLDER NAME
ꢀꢀ
“NO SUPPORT" will be displayed if the MP3 file contains no
ID3 tag information.
“NO ARTIST” or "NO TITLE" will be displayed if the WMA file
contains no WMA tag information.
“ROOT” will be displayed if the directory name of a root
folder is not labeled.
ꢀTitleꢀIconꢀ
ArtistꢀIconꢀ
FolderꢀIconꢀ
FileꢀIconꢀ
This icon will illuminate when the song title is displayed.
This icon will illuminate when the artist name is displayed.
This icon will illuminate when the folder name is displayed.
This icon will illuminate when the track name is displayed.
ꢀ
ꢀ
CharacterꢀSupport
(MP3ꢀID3ꢀtagꢀv1.0ꢀ-ꢀ1.1)
ꢀ
Maximum character display information
• Track name – 30 character maximum
• Folder name – 30 character maximum
• *Song title – 30 character maximum
• *Artist name – 30 character maximum
CharacterꢀSupport
(MP3ꢀID3ꢀtagꢀv2.0ꢀ-ꢀ2.4)
(WMAꢀtags)
Maximum character display information
• Track name – 64 character maximum
• Folder name – 64 character maximum
• *Song title – 64 character maximum
• *Artist name – 64 character maximum
*Song title and Artist Name will only be displayed if included
with the MP3/WMA file.
When referring to MP3/WMA playback, the following terms
are synonymous:
• File name and track name
• Folder name and directory name
14
XHD7714ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
Folder/FileꢀSearchꢀMode
Press SELECT to enter the folder/file search mode. The unit
will read the CD, and a list of folders and files from the CD
will be displayed, starting from the current folder.
(stepꢀ1)
• The current folder name will be displayed on the top line.
• The list of folders and files contained in the current
directory will be on the bottom line of the display.
Folder/FileꢀSelection
(stepꢀ2)
Turn the volume knob to cycle through the list of folders and
files.
Folders will be displayed first, followed by any files.
FOLDER 1
FOLDER 2
FILE 1
FILE 2
Etc . . .
• When a folder name is being displayed,
• When a file name is being displayed,
will illuminate.
will illuminate.
ChangingꢀDirectories
(stepꢀ3)
Press SELECT when a folder is displayed to change
directories and begin displaying the contents of that folder.
When searching the contents of a subfolder, press ESC to
navigate up one folder level.
Pressing ESC from the root directory will exit search mode.
FileꢀPlayback
(stepꢀ4)
Press SELECT when a file is displayed to begin playback of
that file.
15
XHD7714ꢀOPERATIONꢀ
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
FolderꢀAccessꢀ
Press
Press
to select the previous folder.
to select the next folder.
Note:ꢀFolder access is only available on MP3/WMA discs
recorded with more than one folder.
Repeat
Press RPTꢀto enter the Repeat menu, then turn the volume
knob to select one of the following options:
• ALL - Continuously repeats the entire disc.
• TRACK - Continuously repeats selected track.
• FOLDER - Continuously repeats all files in selected folder.
Random
Press RDMꢀto enter the Random menu, then turn the volume
knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL- Plays all tracks in random order.
• FOLDER - Plays all tracks in folder in random order.
Note: Random mode is retained in memory when selecting
between AM/FM, CD, USB, iPod, AUX and Bluetooth modes
and when the unit is turned on/off.
Intro
Press INTꢀto enter the Intro menu, then turn the volume
knob to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ALL - Plays first 10 seconds of each track.
• FOLDER - Plays first 10 seconds of each track in folder.
Note: Folder repeat, random and intro options only function
on MP3/WMA discs recorded with more than one folder.
16
XHD7714ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
MediaꢀCompatibility The following types of discs/files are compatible:
• CD-ROM (ISO), CD-R, CD-RW
• CD-DA
• MP3 data
• WMA data
The following types of discs/files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management).
• WMA lossless format
• Discs recorded with Track At Once or packet writing
• MP3 PRO format
• MP3 playlists
• WAV format
PlaybackꢀOrder MP3/WMA playback sequence is based on recorded order
of files and begins in the root folder of the disc. Any empty
folders or folders that do not include MP3/WMA files are
skipped. This unit may not play files in the order they were
recorded in. Refer to your recording software’s user’s
manual for more information.
CompatibleꢀRecordingꢀ • ISO9660 level 1
Formats • ISO9660 level 2
• Yellow Book MODE 1
• Yellow Book MODE 2 FORM 1
• Multi session
• Maximum folders and files - 256
• Maximum folder levels - 8
• MPEG-1/2/2.5 Audio Layer-3
ISO9660 standards:
• Maximum nested folder depth is 8 (including the root
folder).
• Valid characters for folder/file names are letters A-Z
(all caps), numbers 0-9, and “_” (underscore). Some
characters may not be displayed correctly, depending on
the character type.
• This device can play back discs in Joliet, Romeo, and other
standards that conform to ISO9660. MP3/WMA written in the
formats other than the above may not play and/or their file
names or folder names may not be displayed properly.
17
XHD7714ꢀOPERATIONꢀ
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
AdditionalꢀMP3/WMAꢀ An internal buffer provides ESP (Electronic Skip Protection)
Information to virtually eliminate skipping.
When playing a disc recorded with regular audio files
(CD-DA or .WAV) and MP3/WMA files, the unit will play the
MP3/WMA files only.
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be
played.
Do not attempt to play discs which contain non-MP3/WMA
files with the MP3/WMA extension.
SamplingꢀFrequencyꢀRates
MP3 8kHz ~ 48kHz
WMA 32kHz ~ 48kHz
TransferꢀBitꢀrates
MP3 32kbps ~ 320kbps constant
Variable bit rates
WMA 48kbps ~ 192kbps constant
Variable bit rates
Note:
Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3ꢀTagꢀDisplay ID3 tags Version 1.0 to 2.4
RecommendedꢀSettings For best results, use the following settings when burning
an MP3 disc:
128kbps or higher constant bit rate
44.1kHz or higher sampling frequency
For best results, use the following settings when burning a
WMA disc:
64kbps or higher constant bit rate
32kHz or higher sampling frequency
18
XHD7714ꢀOPERATION
USBꢀOperationꢀ-ꢀMP3/WMAꢀFilesꢀ(Optional)
ConnectingꢀaꢀUSBꢀDevice Play MP3/WMA files from most mass storage devices by
(soldꢀseparately) connecting them to the XHD7714's USB port.
PlayingꢀMusic When a USB device is first connected, play will begin
automatically, and “READING” will appear momentarily in
the display. Depending on the number of files and folders,
this may take several seconds. If no valid MP3/WMA files
are detected, “NO FILE” will be displayed and the last mode
will be resumed.
TrackꢀSelect Press TRACKꢀ
to skip to the beginning of the next
ll
track. Press TRACK
to return to the beginning of the
nn
current track. Pressing TRACK
beginning of the previous track.
again skips to the
nn
FastꢀForwardꢀandꢀReverse Press and hold TRACKꢀ
or TRACK
to fast
ll
nn
forward or reverse a track.
Pause Press
/
/
II to temporarily stop USB playback.
II again to resume playback.
l
l
Press
DisplayingꢀInformation When a file is accessed, the clock and elapsed time will
be displayed. Press DISP momentarily to select file name
(default), song title, artist, track number or clock & elapsed
time.
(LINE 1)
(LINE 2)
ARTIST
SONG TITLE
ELAPSED TIME
CLOCK
TRACK NUMBER
TOTAL TRACKS
FILE NAME
FOLDER NAME
“NO SUPPORT" will be displayed if the MP3 file contains no
ID3 tag information.
“NO ARTIST” or "NO TITLE" will be displayed if the WMA file
contains no WMA tag information.
“ROOT” will be displayed if the directory name of a root
folder is not labeled.
ꢀTitleꢀIconꢀ
ArtistꢀIconꢀ
FolderꢀIconꢀ
FileꢀIconꢀ
This icon will illuminate when the song title is displayed.
This icon will illuminate when the artist name is displayed.
This icon will illuminate when the folder name is displayed.
This icon will illuminate when the track name is displayed.
ꢀ
ꢀ
FolderꢀAccessꢀ Press
to select the previous folder.
to select the next folder.
Press
Note: Folder access is only available on USB devices with
more than one folder.
19
XHD7714ꢀOPERATION
USBꢀOperationꢀ-ꢀMP3/WMAꢀFilesꢀ(Optional)
Repeat Press RPTꢀto enter the Repeat menu, then turn the volume
knob to select one of the following options:
• ALL - Continuously repeats the entire disc.
• TRACK - Continuously repeats selected track.
• FOLDER - Continuously repeats all files in selected folder.
Random
ꢀ
Press RDMꢀto enter the Random menu, then turn the volume
knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL- Plays all tracks in random order.
• FOLDER - Plays all tracks in folder in random order.
Note: Random mode is retained in memory when selecting
between AM/FM, CD, USB, iPod, AUX and Bluetooth modes
and when the unit is turned on/off.
Intro
Press INTꢀto enter the Intro menu, then turn the volume knob
to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ALL - Plays first 10 seconds of each track.
• FOLDER - Plays first 10 seconds of each track in folder.
Folder/FileꢀSearchꢀMode
(stepꢀ1)
Press SELECT to enter the folder/file search mode. The unit
will read the CD, and a list of folders and files from the CD
will be displayed, starting from the current folder.
• The current folder name will be displayed on the top line.
• The list of folders and files contained in the current
directory will be on the bottom line of the display.
Folder/FileꢀSelection
(stepꢀ2)
Turn the volume knob to cycle through the list of folders and
files.
Folders will be displayed first, followed by any files.
FOLDER 1
FOLDER 2
FILE 1
FILE 2
Etc . . .
• When a folder name is being displayed,
• When a file name is being displayed,
will illuminate.
will illuminate.
ChangingꢀDirectories
(stepꢀ3)
Press SELECT when a folder is displayed to change
directories and begin displaying the contents of that folder.
When searching the contents of a subfolder, press ESC to
navigate up one folder level.
Pressing ESC from the root directory will exit search mode.
FileꢀPlayback
(stepꢀ4)
Press SELECT when a file is displayed to begin playback of
that file.
20
XHD7714ꢀOPERATION
USBꢀOperationꢀ-ꢀMP3/WMAꢀFilesꢀ(Optional)
CharacterꢀSupport Maximum character display information
(MP3ꢀID3ꢀtagꢀv1.0ꢀ-ꢀ1.1) • Track name – 30 character maximum
ꢀ
• Folder name – 30 character maximum
• *Song title – 30 character maximum
• *Artist name – 30 character maximum
CharacterꢀSupport Maximum character display information
(MP3ꢀID3ꢀtagꢀv2.0ꢀ-ꢀ2.4) • Track name – 64 character maximum
(WMAꢀtags) • Folder name – 64 character maximum
• *Song title – 64 character maximum
• *Artist name – 64 character maximum
*Song title and artist name will only be displayed if included
with the MP3/WMA file.
MediaꢀCompatibility The following types of files are compatible:
• MP3 data
• WMA data
The following types of files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management).
• WMA lossless format
• MP3 PRO format
• MP3 playlists
• WAV format
PlaybackꢀOrder MP3/WMA playback sequence is based on order the files are
copied to the USB device and begins in the root folder. Any
empty folders or folders that do not include MP3/WMA files
are skipped. Depending on your software, the playback order
may vary.
PlaybackꢀCapacity • Maximum number of files: 28000
• Maximum number of folders: 255 plus the root directory
• Maximum number of files in each folder and root: 999
• Maximum number of folder levels (sub folders): 8
(7 levels plus the root)
Note: If the number of files/folders exceeds the maximum
outlined above, the additional files/folders will be ignored.
USBꢀDeviceꢀCompatibility Due to the differences of USB devices, some devices may not
be compatible. USB devices must be ‘mass storage class’
and formatted to the FAT or FAT32 file system in order to
ensure compatibility.
21
XHD7714ꢀOPERATION
USBꢀOperationꢀ-ꢀMP3/WMAꢀFilesꢀ(Optional)
AdditionalꢀMP3/WMAꢀ Only MP3 files with filename extension (.mp3) can be played.
Information Only WMA files with filename extension (.wma) can be
played. Do not attempt to play non-MP3/WMA files with the
MP3/WMA extension.
SamplingꢀFrequencyꢀRates
MP3 8kHz ~ 48kHz
WMA 32kHz ~ 48kHz
TransferꢀBitꢀrates
MP3 32kbps ~ 320kbps constant
Variable bit rates
WMA 48kbps ~ 192kbps constant
Variable bit rates
Note: Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3ꢀTagꢀDisplay ID3 tags Version 1.0 to 2.0
Note: If an invalid ID3 tag version is detected, "NO
SUPPORT" will scroll on the display.
22
XHD7714ꢀOPERATION
iPod®ꢀOperationꢀ(Optional)
ConnectꢀiPod
(NotꢀIncluded)
Use the included 2-wire iPod cable to connect an iPod to the
XHD7714. Once connected, press MODE until "IPOD" appears
in the display. The iPod will automatically begin playback.
If a song is playing on the iPod before it is connected, it will
continue to play.
Note: Both the USB and auxiliary input connections must be
made when connecting the 2-wire iPod cable.
DisplayingꢀInformation
Press DISP to select the display options as follows:
(LINE 1)
ARTIST
ARTIST
ELAPSED TIME
TRACK NUMBER
(LINE 2)
SONG TITLE
ALBUM
CLOCK
TOTAL TRACKS
“UNKNOWN ARTIST” will be displayed if the file contains no
artist tag information.
“UNKNOWN ALBUM” will be displayed if the file contains no
album tag information.
iPod®ꢀSearchꢀMode
SearchꢀMenuꢀFunctions
(stepꢀ1)
Press SELECT once to enter the search mode.
(stepꢀ2)
Turn the volume knob to select between playlist, artist,
album, song and podcast. Press SELECT to select the desired
search type.
(stepꢀ3)
Navigate to the desired song and press SELECT to begin
playback of that song. Use the table below for reference
when navigating through the menu options.
Note: Press ESC to access the previous level (up one level).
Pressing ESCꢀfrom the iPod search main menu will exit the
search.
See the below table for a list of the iPod search menu navigation options.
Menu Navigation
Songs
Search Item
Menu
Playlists
Playlist
Artist
Menu
Menu
Menu
Menu
Artists
Albums
Songs
Songs
Album
Song
Podcast
Albums
Songs
Podcasts
23
XHD7714ꢀOPERATION
iPod®ꢀOperationꢀ(Optional)
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀSongꢀSelect
Press
Press
to skip to the beginning of the next song.
to return to the beginning of the current song.
again skips to the beginning of the previous
ll
nn
Pressing
song.
nn
ꢀꢀFastꢀForwardꢀandꢀ
Press and hold
song.
or
to fast forward or reverse a
ll nn
Reverse
ꢀꢀ
Pause
Press / II again to resume playback.
Press / II to temporarily stop playback.
l
l
Repeat
Press RPTꢀto enter the Repeat menu, then turn the volume
knob to select one of the following options:
• ALL - Repeats the entire iPod device.
• SONG - Repeats selected track.
Random
Press RDMꢀto enter the Random menu, then turn the
volume knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL- Plays all tracks in random order.
• ALBUM - Plays all tracks in the selected album in
random order.
Intro
Press INTꢀto enter the Intro menu, then turn the volume
knob to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ON - Plays first 10 seconds of each track.
Only alphanumeric characters can be displayed (ASCII
type).
CharacterꢀSupport
"NO SUPPORT" will be displayed if the file contains
characters that can not be displayed.
"NO SONG" will be displayed if there are no songs in the
selected playlist.
Maximum character display information
• *Song title – 30 character maximum
• *Artist name – 30 character maximum
• *Album name – 30 character maximum
*Song Title, Artist Name and Album name will only be
displayed if included with the file.
The following models are supported:
• iPod (third generation) - Version 2.3
• iPod (fourth generation) - Version 3.1.1
• iPod (fifth generation) - Version 1.1.2
• iPod Classic - Version 1.1.2
iPodꢀCompatibility
• iPod Touch - Version 1.1.4
• iPod Photo - Version 1.2.1
• iPod Mini - Version 1.4.1
• iPod Nano - Version 1.3.1
• iPod Nano (second generation) - Version 1.1.3
• iPod Nano (third generation) - Version 1.1.2
Refer to your iPod instruction manual for details on how to
obtain the latest software.
24
XHD7714ꢀOPERATION
Bluetooth®ꢀOperation
Overview
The XHD7714 supports the HFP (hands-free profile), A2DP (advanced audio distribution
profile) and AVRCP (audio video remote control profile).
Preparation
Before you can use a mobile device with this head unit, it must be connected and
authenticated - commonly referred to as "pairing" a device. Please make sure that
Bluetooth is activated on your mobile device before you begin the pairing process. Refer
to the owner's manual of your mobile device for more details.
BluetoothꢀPairing
1) To pair a Bluetooth enabled mobile phone to your head unit, press on the head unit,
or press MODE until "BLUETOOTH" scrolls once then "STANDBY" is displayed.
2) Press and hold on the head unit for 5 seconds, until "PAIRING" is displayed, the
Bluetooth icon will flash every second. The head unit will begin to broadcast a signal for
90 seconds.
3) Complete the pairing from the Bluetooth menu of your mobile device by searching for
new devices. Please refer to your mobile device instructions for further information on
Bluetooth pairing and connections. The Bluetooth icon will illuminate solid.
TheꢀBTM60ꢀdeviceꢀnameꢀisꢀ"DUALꢀBT."ꢀꢀ
TheꢀpasswordꢀforꢀtheꢀDUALꢀXHD7714ꢀisꢀ1234.ꢀꢀ
ConnectionꢀNotes
• If ACNT is set to OFF, you must press to connect after pairing.
• From Bluetooth standby mode, press
ꢀto disconnect your mobile device.
• From Bluetooth standby mode, press to reconnect your mobile device.
• To connect a different mobile device, the currently connected mobile device must be
disconnected. If this device has been paired previously, you may reconnect using the
mobile device's Bluetooth menu, or repeat the above pairing instructions.
GeneralꢀNote
• Due to the differences in Bluetooth technology, some mobile devices may be
incompatible or function improperly when used with the XHD7714.
• The Bluetooth microphone is built into the front panel of the XHD7714.
25
XHD7714ꢀOPERATION
Bluetooth®ꢀOperation
Description
Function
Press once. "Enter Number" will be shown, then An "_" will
appear on the display.
Input the desired phone number using the 0-9, *, # buttons on the
MakingꢀaꢀPhoneꢀCall remote control. Press to begin dialing.
A phone call may also be placed from your mobile device using
the keypad, phone book or speed dial. When a call is placed from
a mobile device, “DIALING” will appear on the head unit display.
If an incoming call is detected, the head unit will automatically
switch to Bluetooth mode, muting any current audio.
The incoming phone number will scroll across the display, the
phone icon will flash on the display, and a ring tone will be
audible from the vehicle speakers. See Bluetooth Settings for
speaker configurations.
ReceivingꢀaꢀPhoneꢀ
Call
NOTE: The ring audio level will depend the mobile device and
head unit ring volume and audio settings. If the ringer on the
mobile device is off, you may not hear an incoming ring tone.
Press on the head unit to receive a call. The phone icon in the
display will illuminate solid.
The head unit will display the elapsed time of the phone call.
The volume knob will adjust the volume of the call.
DuringꢀaꢀPhoneꢀCall
RefusingꢀaꢀCall
Press
to mute the built-in microphone during a call.
To refuse an incoming phone call, press and hold
seconds.
for 3
Hold
for 3 or more seconds to end a call.
EndingꢀaꢀPhoneꢀCall
If the phone call was received, the head unit will return to
previous mode when call is ended.
26
XHD7714ꢀOPERATION
Bluetooth®ꢀSettings
Description
Function
To enter last number dialing mode, press , then press
second time. The head unit will display "LASTCALL MENU."
Press DISP to cycle through the received, dialed or missed call
a
LastꢀNumberꢀDialing categories. Rotate the volume knob to cycle through the last 5
calls in the selected category.
Press to begin dialing the selected number. “DIALING” will
appear on the head unit display.
To transfer the phone call between the head unit and the mobile
device, press and hold DISP for 3 seconds during a call. Tip:
transfer audio to your mobile device before turning the head unit
AudioꢀTransfer
off.
When a second call is incoming, press to activate call waiting.
CallꢀWaiting
CallꢀHold
The current call will be placed on hold, and the second call will be
active. Press again to return to the first call.
Press to place the current call on hold. To resume the phone
call, press ꢀagain.
BluetoothꢀSetupꢀMenu
Options
BT ON
Action
Menu Function
Enables Bluetooth mode. The Bluetooth icon will
flash every 10 seconds.
BluetoothꢀModeꢀ
BT OFF
Disables Bluetooth support.
AUTO-CON Allows the XHD7714 to automatically (re)connect to
ON
the most recently connected mobile device. Note:
Some mobile devices do not support this feature.
AutoꢀConnect
AUTO-CON
OFF
Disables the auto connect feature. You must press
every time to connect a mobile device.
AUTO-ANS
OFF
Disables the auto answer feature. Press to receive
an incoming call.
AutoꢀAnswer
AUTO-ANS All incoming calls will be answered automatically -
ON
without notification.
SPK 2-CH
SPK 4-CH
Directs the Bluetooth audio to the front speakers.
Directs the Bluetooth audio to all 4 speakers.
BluetoothꢀAudio
*See page 7 for Setup Menu navigation
27
XHD7714ꢀOPERATION
Bluetooth®ꢀOperation
BluetoothꢀStreamingꢀAudioꢀOperation
(AVꢀMODE)
The XHD7714 supports A2DP wireless streaming audio from your Bluetooth mobile device
directly to your head unit. You can also control your music from the front panel of the head
unit using AVRCP.
To stream music to your head unit, your mobile device must support the following criteria:
• A2DP profile to stream audio
• AVRCP profile to control your music. Check the owner's manual or manufacturer
of your device for compatibility.
• Streaming audio must be enabled from your mobile device. This option will vary
depending on the device. Example: "wireless stereo."
• Disabling AV MODE must be done from your mobile device.
After enabling streaming audio from a compatible mobile device, the head unit will display
"AV MODE." The following functions can be used to control music:
• The
• The
• The
• The
button will skip to the next available audio track.
button will skip to the previous audio track.
II button will toggle between play and pause during playback.
ll
nn
/
l
button will stop the audio playback.
NOTE: If you are experiencing problems with these functions, try playing music from the
mobile device. On some mobile devices, it may be necessary to control the music from the
device.
28
XHD7714ꢀOPERATION
LimitedꢀOneꢀYearꢀWarranty
This warranty gives you specific legal rights.
Whatꢀtoꢀdo?
You may also have other rights which vary from
state to state.
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any custom
controls may save you a service call.
Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
material and workmanship for a period of one
year from the date of the original purchase.
2. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and ship
it by prepaid transportation with a copy of the
original receipt from the retailer to an
authorized service center.
Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any defect
in material or workmanship or to furnish an
equal new, renewed or comparable product
(whichever is deemed necessary) in exchange
without charges, subject to verification of the
defect or malfunction and proof of the date of
purchase. Subsequent replacement products
are warranted for the balance of the original
warranty period.
3. Please describe your problem in writing and
include your name, a return UPS shipping
address (P.O. Box not acceptable), and a
daytime phone number with your shipment.
4. For more information and for the location of
the nearest authorized service center please
contact us by one of the following methods:
Whoꢀisꢀcovered?ꢀThis warranty is extended to
the original retail purchaser for products
purchased and used in the U.S.A.
• Call us toll-free at 1-866-382-5476
• E-mail us at [email protected]
Whatꢀisꢀcovered?ꢀThis warranty covers all
defects in material and workmanship in this
product. The following are not covered:
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect
line voltage, unauthorized repair or failure to
follow instructions supplied with the product,
or damage occurring during return shipment of
the product.
Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether
or not arising from the company’s negligence,
actual or imputed. No person or representative
is authorized to assume for the company any
other liability in connection with the sale of
this product. In no event shall the company be
liable for indirect, incidental or consequential
damages.
29
XHD7714ꢀOPERATION
Troubleshootingꢀ-ꢀGeneral
Problem
Cause
Action
Yellow wire not connected or incorrect
voltage Red wire not connected or
incorrect voltage
Check connections for proper
voltage (11~16VDC)
Unitꢀwillꢀnotꢀturnꢀonꢀ
(noꢀpower)
Black wire not connected
Fuse blown
Check connection to ground
Replace fuse
Speaker wires not connected
Check connections at speakers
Unitꢀhasꢀpowerꢀ
(butꢀnoꢀsound)
One or more speaker wires touching each Insulate all bare speaker wires
other or touching chassis ground
from each other and chassis
ground
Yellow or red wire touching chassis
ground
Check for pinched wire
Unitꢀblowsꢀfuses
Speaker wires touching chassis ground
Incorrect fuse rating
Check for pinched wire
Use fuse with correct rating
Unit is not mounted correctly or backstrap Check mounting sleeve and
is not secure
backstrap support
Excessiveꢀskipping
Physical defect in media (CD, CD-R or
CD-RW)
Check media for scratches
ERROR-01ꢀappearsꢀ
onꢀdisplay
Disc read error
Press eject or RESET
Press eject or RESET
Focus error or disc is in upside down
ERROR-02ꢀappearsꢀ
onꢀdisplay
PROTECTꢀappearsꢀ
onꢀdisplay
The WMA file is copy-protected by DRM
(Digital Rights Management)
Write disc using WMA files that
are not copy-protected
Selected file is not available in direct or
alphanumeric search modes
Repeat search using valid
parameters
NOꢀFILEꢀappearsꢀ
onꢀdisplay
The file format is incompatible
Write disc using valid audio
files with .mp3 or .wma file
extensions
INVALIDꢀappearsꢀ
onꢀdisplay
CD mechanism position out of alignment
CD transit screws still in place
Press and hold EJECTꢀfor 3
seconds to reset CD mechanism
position
Unitꢀwillꢀnotꢀacceptꢀ
aꢀdisc
Remove 2 transit screws located
on top of the unit
Pairing attempt has exceeded 90 seconds Retry pairing sequence. Pairing
must complete within 90
seconds.
PAIRINGꢀFAILEDꢀ
appearsꢀonꢀtheꢀdisplay
Phone is not setup correctly to connect to
a bluetooth hands free device.
Check the device owner's manual
for instructions on enabling
Bluetooth.
Bluetooth device may not be compatible
withꢀthe XHD7714
Contact customer service for
more information.
30
XHD7714ꢀOPERATION
Specifications
CDꢀPlayer Frequency response: 10Hz-20kHz
Channel separation @ 1kHz: >65dB
D/A converter: 1ꢀBit
FMꢀTuner Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz
AMꢀTuner Tuning range: 530kHz-1710kHz
Usable sensitivity: 22uV
Frequency response: 30Hz-2.2kHz
General Operating voltage: 11-16ꢀVDC,ꢀnegativeꢀground
Speaker output impedance: 4~8ꢀohms
Line output voltage: 2ꢀVoltsꢀRMS
Dimensions: 7"ꢀxꢀ7"ꢀxꢀ2"ꢀ(178ꢀxꢀ178ꢀxꢀ51ꢀmm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 17 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms)
31
Dual Electronics Corp.
Toll Free: 1-866-382-5476
©2008 Dual Electronics Corp. All rights reserved.
Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States
and or other countries. Other trademarks and trade names are those of their respective owners.
iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Movon is under license.
HD Radio™ Technology Manufactured Under License From iBiquity Digital Corp. U.S. and Foreign Patents. HD Radio™ and the
HD Radio logo are proprietary trademarks of iBiquity Digital Corp.
Other trademarks and trade names are those of their respective owners.
NSA0708-V02
|