Chief Manufacturing Projector Accessories XSM User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
XSM  
XTM  
FUSION EXTRA LARGE HEIGHT ADJUST  
FLAT PANEL MOUNTS  
XSM/XTM Series  
 
Installation Instructions  
XSM/XTM Series  
DIMENSIONS  
XSM  
NOTES:  
1. MAX MOUNTING PATTERN IS 46" (1168.4 mm) WITHOUT REVERSING UPRIGHTS.  
2. MAX MOUNTING PATTERN IS 48.4" (1229.4 mm) WITH REVERSED UPRIG HTS.  
3. FOR REC ESSED APPLIC ATIONS, MINIMUM VERTIC AL LIFT FOR HOOK ENGAG EMENT IS .56"[14.2].  
MOUNT IS 2.23"[56.6mm] DEEP WHEN FLAT TO WALL.  
20.6  
.81  
30  
1.18  
39.1  
1.54  
24.3  
.96  
73.9  
2.91  
25.4  
1.00  
MINIMUM UPRIG HT SPACING 24"  
8.3  
.33  
685.8  
27.00  
0
15  
.59  
75  
2.95  
56.6  
2.23  
44.5  
1.75  
383.4  
15.10  
419.6  
16.52  
5.31  
45  
1.77  
RAILS CAN BE SLID LEFT  
OR RIG HT FOR OFFSET  
25.4  
1.00  
1233.4  
48.56  
DIMENSIONS: [MILLIMETERS]  
INCHES  
XTM  
NOTES:  
1. MAX MOUNTING PATTERN IS 44.7" (1135.4 mm) WITHOUT REVERSING UPRIG HTS.  
2. MAX MOUNTING PATTERN IS 49.2" (1249.7 mm) WITH REVERSING UPRIGHTS.  
.40 10.2  
.51 12.9  
FOR REC ESSED APPLIC ATIONS, MINIMUM VERTIC AL LIFT FOR HOOK ENG AG EMENT IS .41"[10.4mm].  
MOUNT IS 1.92"[48.7mm] DEEP WHEN FLAT TO WALL.  
12°  
1.00 25.4  
.96 24.4  
2.00 50.8  
2.92 74.1  
1.00 25.4  
MINIMUM UPRIG HT SPAC ING 24"  
.33 8.3  
.59 15  
0
27.00 685.8  
27.00 685.8  
.59 15  
1.75 44.5  
15.10 383.4  
2.95 75  
1.92 48.7  
MIN.  
16.52 419.6  
DEPTH  
5.31  
RAILS C AN BE SLID LEFT  
OR RIG HT FOR OFFSET  
48.54 1233  
DIMENSIONS: [MILLIMETERS]  
INCHES  
3
 
XSM/XTM Series  
Installation Instructions  
LEGEND  
Tighten Fastener  
Pencil Mark  
Apretar elemento de fijación  
Befestigungsteil festziehen  
Apertar fixador  
Marcar con lápiz  
Stiftmarkierung  
Marcar com lápis  
Segno a matita  
Serrare il fissaggio  
Bevestiging vastdraaien  
Serrez les fixations  
Potloodmerkteken  
Marquage au crayon  
Loosen Fastener  
Drill Hole  
Aflojar elemento de fijación  
Befestigungsteil lösen  
Desapertar fixador  
Perforar  
Bohrloch  
Fazer furo  
Praticare un foro  
Gat boren  
Allentare il fissaggio  
Bevestiging losdraaien  
Desserrez les fixations  
Percez un trou  
Phillips Screwdriver  
Adjust  
Destornillador Phillips  
Ajustar  
Kreuzschlitzschraubendreher  
Chave de fendas Phillips  
Cacciavite a stella  
Einstellen  
Ajustar  
Regolare  
Afstellen  
Ajuster  
Kruiskopschroevendraaier  
Tournevis à pointe cruciforme  
Open-Ended Wrench  
Llave de boca  
Remove  
Quitar  
Gabelschlüssel  
Chave de bocas  
Chiave a punte aperte  
Steeksleutel  
Entfernen  
Remover  
Rimuovere  
Verwijderen  
Retirez  
Clé à fourche  
By Hand  
Optional  
Opcional  
Optional  
Opcional  
Opzionale  
Optie  
A mano  
Von Hand  
Com a mão  
A mano  
Met de hand  
À la main  
En option  
Hex-Head Wrench  
Security Wrench  
Llave de cabeza hexagonal  
Sechskantschlüssel  
Chave de cabeça sextavada  
Chiave esagonale  
Llave de seguridad  
Sicherheitsschlüssel  
Chave de segurança  
Chiave di sicurezza  
Veiligheidssleutel  
Clé de sécurité  
Zeskantsleutel  
Clé à tête hexagonale  
4
 
XSM/XTM Series  
Installation Instructions  
TOOLS REQUIRED FOR INSTALLATION  
#2  
7/32" (5.5mm) Wood Stud  
5/16" (7.9mm) Concrete  
PARTS  
[A-K used on XSMU/XTMU Models Only]  
B (6)  
A (6)  
M6x25mm  
M6x16mm  
C (6)  
M8x20mm  
E (4)  
M8x50mm  
D (6)  
M8x30mm  
M (1)  
[Included with  
XSMXXXX / XTMXXXX  
Models Only]  
G (6)  
M10x50mm  
F (6)  
M10x40mm  
Custom  
XSMXXXX /  
XTMXXXX  
Hardware  
H (6)  
M6  
I (6)  
M8  
N (1)  
(XTM Only)  
JA (6)  
.750x.323x.250"  
JB (6)  
1.00x.400x.75"  
P (1)  
3/16" - 12"  
KA (1)  
M5  
KB (1)  
M6  
R (1)  
T (1)  
LA (4)  
5/16"  
LB (4)  
5/16"  
Q (4)  
LC (4)  
5/16" x 2-1/2"  
S (1)  
U (1)  
(XSM Only)  
(XTM Only)  
5
 
XSM/XTM Series  
Installation Instructions  
INSTALLATION  
Center of screen  
The XTM and XSM have been designed to be mounted directly  
onto either a wood stud or concrete wall. The XTM has brackets  
which allow the display to be tilted. The XSM has static brackets  
which keep the display in an upright position.  
7-1/2"  
(190.5mm)  
Locate Mounting Site  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY  
OR DAMAGE TO EQUIPMENT! It is the installers  
responsibility to make certain the structure to which the  
mount is being attached is capable of supporting five times  
the weight of the XTM or XSM and all attached equipment not  
to exceed 250 lbs (113.4 kg).  
Vertical center  
of mount  
NOTE: For concrete installation, proceed to Installing to a  
Concrete Wall section.  
Installing to a Wood Stud Wall  
CAUTION: MINIMUM HORIZONTAL DISTANCE  
BETWEEN WALL BRACKETS IS 24" (609.6mm). Do not  
place mounting brackets closer together than 24" (609.6mm).  
When attaching to a wall containing studs located 16" on  
center, space the uprights 32" (812.8mm) apart.  
Figure 1  
5. Using a level, mark the wall on each stud to attach the  
mount through the upper mounting slots. (See Figure 2)  
1. Determine the center of the display, and where it should be  
located on the wall.  
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING  
OR DRILLING INTO ELECTRICAL CORDS OR CABLES  
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!  
ALWAYS make certain area behind mounting surface is free  
of electrical wires and cables before drilling or installing  
fasteners.  
2. Locate the appropriate studs to the left and right of the  
selected location.  
NOTE: If the screen area lies over a stud, use that stud and an  
appropriate stud to either the left or right of it.  
3. Line up the notches on mount with center of screen marking  
to determine vertical center. (See Figure 1)  
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING  
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH  
OR SERIOUS PERSONAL INJURY! ALWAYS make certain  
area behind mounting surface is free of gas, water, waste, or  
any other plumbing before cutting, drilling, or installing  
fasteners.  
4. Measure up 7-1/2" (190.5mm) from the center point to mark  
location of the upper mounting slots.  
6. Drill one 7/32" pilot hole in each stud.  
7. Use two 5/16 x 2-1/2" lag bolts (LC) and two 5/16" flat  
washers (LB) to attach top of mount to wall. (See Figure 2)  
6
 
Installation Instructions  
XSM/XTM Series  
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING  
OR DRILLING INTO ELECTRICAL CORDS OR CABLES  
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!  
ALWAYS make certain area behind mounting surface is free  
of electrical wires and cables before drilling or installing  
fasteners.  
6
5
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING  
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH  
OR SERIOUS PERSONAL INJURY! ALWAYS make certain  
area behind mounting surface is free of gas, water, waste, or  
any other plumbing before cutting, drilling, or installing  
fasteners.  
7
(LC) x 4  
10  
8
9
8
9
4
5
(LA) x 4  
6 10  
x4  
(LB) x 4  
Figure 2  
8. Mark the attachment points for the lower mounting slots,  
making sure the attachment points are located on the studs.  
(See Figure 2)  
9. Drill 7/32" pilot holes at markings for lower mounting holes.  
(See Figure 2)  
10. Use two 5/16 x 2-1/2" lag bolts (LC) and two 5/16" flat  
washers (LB) to attach the mount to the wall through the  
lower mounting holes. (See Figure 2)  
11. Slide rails to approximate center of screen location.  
12. Proceed to Attaching Interface Brackets to Display  
(LC) x 4  
7 11  
section.  
(LB) x 4  
Installing to a Concrete Wall  
Figure 3  
5. Drill one 5/16" pilot hole at each marking. (See Figure 3)  
CAUTION: MINIMUM HORIZONTAL DISTANCE  
6. Install an anchor (LA) into each pilot hole using a hammer.  
(See Figure 3)  
BETWEEN WALL BRACKETS IS 24" (609.6mm). Do not  
place mounting brackets closer together than 24" (609.6mm).  
7. Use two 5/16 x 2-1/2" lag bolts (LC) and two 5/16" flat  
washers (LB) to attach top of mount to anchors in wall. (See  
Figure 3)  
1. Determine the center of the display, and where it should be  
located on the wall.  
2. Line up the notches on mount with center of screen marking  
to determine vertical center. (See Figure 1)  
8. Mark the attachment points for the lower mounting slots.  
(See Figure 3)  
3. Measure up 7-1/2" (190.5mm) from the center point to mark  
location of the upper mounting slots. (See Figure 1)  
9. Drill one pilot hole at each marking for lower mounting  
holes. (See Figure 3)  
4. Using a level, mark the wall through both upper mounting  
slots. (See Figure 3)  
10. Install an anchor (LA) into each pilot hole using a hammer.  
(See Figure 3)  
11. Use two 5/16 x 2-1/2" lag bolts (LC) and two 5/16" flat  
washers (LB) to attach the mount to the wall through the  
lower mounting holes. (See Figure 3)  
12. Slide rails to approximate center of screen location.  
7
 
XSM/XTM Series  
Installation Instructions  
Switching Interface Brackets (Optional)  
Attaching Interface Brackets to Display  
1. Align the center of the bracket with center of screen.  
(See Figure 4)  
If an installation situation makes adjusting the location of  
interface brackets necessary, there are several options.  
NOTE: The diamond-shape hole in the bracket corresponds to  
1. The wall brackets may be adjusted side to side at the point  
of attachment. (See Figure 5)  
the center of the mount.  
2. The location of the left and right interface brackets may be  
switched, with the knobs on the XTM interface brackets  
facing the inside of the mount. (See Figure 5)  
1
Knobs  
Center of bracket  
Figure 4  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
DISPLAY FALLING CAUSING SERIOUS PERSONAL  
INJURY OR DAMAGE TO EQUIPMENT! Using screws of  
improper size may damage your display. Properly sized  
screws will easily and completely thread into display  
mounting holes. If spacers are required, be sure to use longer  
screws of the same diameter.  
2
2. Select correct screws, spacers (if necessary) and washers  
from the hardware bag (A-K) and attach brackets to back of  
screen. (See Figure 4)  
Figure 5  
8
 
Installation Instructions  
XSM/XTM Series  
3. If necessary, the tilt interface bracket knobs may be  
switched to allow the interface brackets to be reversed.  
(See Figure 6)  
2. Adjust Velcro® pull strap (if necessary) so it does not  
extend beyond bottom of screen. (See Figure 8)  
NOTE: NEVER place both interface brackets to one side of the  
a. Remove display from mount.  
b. Remove interface brackets from display.  
c. Hold the right interface bracket horizontally, tightly  
gripping it so that spacers do not move.  
wall mount center line! (See Figure 8)  
NOTE: Do NOT allow both interface brackets to be located on  
same side of wall bracket. (See Figure 8)  
d. Remove the knob, washer and screw.  
e. Replace the knob, washer and screw in the opposite  
order, with the knob on the inside of the bracket.  
Center Line (CL)  
f. Switch the right interface bracket to the left side of the  
wall mount.  
g. Repeat Steps 3c through 3f with the left interface  
bracket.  
3d  
Pull strap  
3e  
NEVER place both interface brackets to one  
side of the wall mount center line (CL)!  
Knobs to outside  
of brackets  
Figure 6  
Attaching Screen to Wall Mount  
1. Attach wall bracket caps (Q) to top and bottom of both wall  
brackets. (See Figure 7)  
Both interface brackets must NEVER be located  
to one side of the wall brackets!  
Figure 8  
1
(Q) x 4  
Figure 7  
9
 
XSM/XTM Series  
Installation Instructions  
XTM Model  
XSM Model  
8. Push interface bracket tab all the way down so that the  
lower mounting slot is blocked. (See Figure 10)  
NOTE: Proceed to Step 8 for XSM Model instructions.  
3. Hang top hook of interface brackets onto the top bar of the  
mount. (See Figure 9)  
NOTE: The screen initially installs into the "kickstand mode" to  
allow easy cable access.  
Latch  
closed  
4. Slide screen and bars to desired viewing position.  
5. Route cables between wall and bars.  
CAUTION: PINCH POINTS! Keep fingers, hands and  
cables out of pinch point areas.  
Latch  
open  
6. Pull downward on the pull straps and swing inward toward  
wall, latching interface brackets to lower bar and locking  
bottom of screen to the mount. (See Figure 9)  
7. Proceed to Adjusting Roll/Height of Wall Brackets  
section.  
Interface  
bracket  
tab  
12  
(Screen not shown for clarity)  
8
10  
Top  
Hook  
Figure 10  
3
9. Hang the top hook of interface brackets onto the top bar of  
the mount. The bottom of the screen will be away from the  
wall.  
10. Move screen towards the wall by pulling display bottom  
away from wall and pushing the interface bracket tabs up  
one notch to the detent which you will be able to feel  
(approximately half way up).  
11. Push bottom of display toward the wall bracket so that lower  
latch on interface bracket surrounds lower bar of wall  
mount.  
12. Raise interface brackets tabs all the way to secure the  
brackets onto the wall mount. (See Figure 10)  
6
Pull straps  
Figure 9  
10  
 
Installation Instructions  
XSM/XTM Series  
Adjusting Roll/Height of Wall Brackets  
Locking XSM Mount (Optional)  
Add padlock (not included) to interface bracket tab to lock the  
XSM mount. (See Figure 13)  
NOTE: The height adjust wall brackets allow adjustment of  
+ 1/2".  
1. Turn to right (tighten) to raise side of screen.  
(See Figure 11)  
2. Turn to left (loosen) to lower side of the screen.  
1
Raises screen  
Lowers screen  
2
(P)  
Add padlock  
(Screen not shown for clarity)  
Figure 11  
Figure 13  
Locking XTM Mount (Optional)  
1. Add optional security bracket (N) to the mount.  
(See Figure 12)  
2. Add padlock (not included) to complete security.  
(XTM Shown)  
(N)  
1
2
Figure 12  
11  
 
XSM/XTM Series  
Installation Instructions  
USA/International  
Europe  
A
P
F
A
P
F
6436 City West Parkway, Eden Prairie, MN 55344  
800.582.6480 / 952.225.6000  
877.894.6918 / 952.894.6918  
Franklinstraat 14, 6003 DK Weert, Netherlands  
+31 (0) 495 580 852  
+31 (0) 495 580 845  
Chief, a products division of  
Milestone AV Technologies  
Asia Pacific  
A
Office No. 1 on 12/F, Shatin Galleria  
18-24 Shan Mei Street  
Fotan, Shatin, Hong Kong  
852 2145 4099  
852 2145 4477  
8800-002518 Rev00  
¤2014 Milestone AV Technologies  
03/14  
P
F
 

Black Decker Juicer JBGM600 B5 User Manual
Black Decker Microwave Oven MY30PGCS User Manual
Blanco Indoor Furnishings 157 065 User Manual
Bowflex Treadmill TC5300 User Manual
BOXLIGHT Projector CP 322i CP 634i User Manual
Bretford Outdoor Cart LAP24EBA User Manual
Califone MP3 Player MP2008 User Manual
Canon Printer BJC 3000 User Manual
Casio Calculator FX260SLR User Manual
Cecilware Hot Beverage Maker Choco 1 User Manual