I N S T A L L A T I O N I N S T R U C T I O N S
LCD Swivel Stand
MSS6000
Installation Instructions
MSS6000
LEGEND
Pencil Mark
Tighten Fastener
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Drill Hole
Loosen Fastener
Perforar
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Adjust
Phillips Screwdriver
Ajustar
Destornillador Phillips
Einstellen
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Remove
Quitar
Open-Ended Wrench
Llave de boca
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Optional
Opcional
Optional
Opcional
Opzionale
Optie
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Security Wrench
Hex-Head Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
3
MSS6000
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
#2
3/16"
(Provided)
5/32"
(Provided)
3/8"
PARTS
A (1)
B (5)
.5x.5x.203
D (1)
3/16"
C (1)
5/32"
4
Installation Instructions
MSS6000
To install a display with a height greater than 24":
INSTALLATION
1. Remove slide plate assembly from the base by
removing four 5/16-18 x 3/4" button head cap screws, and
four 1/4" flat washers. (See Figure 3)
Mount Installation
Free Standing (not anchored) Applications Only:
NOTE: Do not perform this step if you are going to anchor the
stand to a surface.
x 4
1
1. Install five rubber bumpers (B) on bottom of stand. (See
Figure 1)
4
x 4
x 4
Rubber Bumpers
(5 places)
Base
Assembly
Slide
Plate
Assembly
View from Bottom
Figure 3
Figure 1
2. Remove face plate from slide plate assembly by
removing two 3/8"-16 x 1" round head carriage bolts,
two 1" OD x .563 ID spacers, two 3/8" flat washers,
and two 3/8-16 lock nuts. (See Figure 5)
Display 24 Inches High or Smaller:
1. Loosen the four height adjustment screws and raise
the slide to its maximum height. (See Figure 2)
3. Reinstall face plate into upper mounting holes of slide
plate using two 3/8"-16 x 1" round head carriage bolts,
two 1" OD x .563 ID spacers, two 3/8" flat washers,
and two 3/8-16 lock nuts removed in Step 2. (See
Figure 5)
2. Secure the slide by tightening the four height
adjustment screws.
Faceplate Height Adjustment Screws (4)
4. Reinstallslideplateassemblyontobaseusingfour
5/16-18 x 3/4" button head cap screws and four 1/4" flat
washers previously removed in Step1. (See Figure 3)
5. Raise slide plate assembly to maximum height.
6. Secure slide plate in place by tightening the four
height adjustment screws. (See Figure 2)
Slide
Plate
Face
Plate
Lock
Nut
Flat
Washer
Figure 2
Display More Than 24 Inches High:
Spacer
NOTE: The MSS-6000 comes pre-configured for displays
24” in height or less. If a display with a height
greater than 24" is being installed follow the
instructions below.
Carriage Bolt
Figure 4
5
MSS6000
Installation Instructions
Display Installation
The following procedure assumes that the proper
interface bracket for the display being mounted has
already been installed on the display.
May remove
pin and nut and
move to lower holes
If no interface bracket is present on display, install
bracket to display using the instructions included with the
interface bracket before proceeding.
1
If an interface bracket for the display being mounted
needs to be obtained, or additional assistance is
required, contact a Chief Customer Service
representative by calling 1-800-582-6480 or by visiting
2
NOTE: If the display being mounted has a height of more
than 24" the mount needs to be modified prior to
display installation.
A padlock or bolt
may be placed
through latch holes
(See Display More Than 24 Inches High on
page 5)
To install the display:
Figure 6
1. While supporting both sides of display, align four mounting
buttons on display or interface bracket with four mounting
holes in faceplate. (See Figures 5 and 6)
Removing Display from Mount
1. Remove bolt or padlock from faceplate (if used).
(See Figure 7)
NOTE: The pin may have been used as a more permanent
locking device. If so, remove nut and pin and move
from the lower holes to the upper holes.
1
2. Pull back on flag on upper mounting hole and press pin
down into "Open" position. (See Figure 7)
3. Carefully lift display from mount.
4. Lift up on pin and place flag back against faceplate to return
it to "Closed" position. (See Figure 7)
Figure 5
2. Lower display into place listening for audible "click" to
ensure recessed area of mounting buttons are properly
seated in lower area of mounting holes. (See Figures 5 & 6)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Ensure mounting
buttons are completely engaged in mounting holes.
NOTE: Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See Figure 6).
6
Installation Instructions
MSS6000
Remove bolt
or padlock
if used
1
Height Adjustment
Screws
2
5" Max.
(2 each side)
Pin in
"Closed"
position -
move to
"Open"
position to
remove
display
4
Figure 8
Display Roll Adjustment
The MSS-6000 provides limited display roll adjustment
for the purpose of leveling the display.
Pin in
"Open"
position -
move to
"Closed"
position
To level the display:
1. Loosen upper and lower roll adjustment nuts.
(See Figure 9)
2. Level display. (See Figure 9)
3. Tighten roll adjustment nuts.
after display
is removed.
Figure 7
ADJUSTMENTS
Display Height Adjustment
CAUTION: Displays are fragile. Allowing the display to
drop to bottom of stand may result in damage to the
display.
1. While holding the display, loosen the four height
adjustment screws. (See Figure 8)
CAUTION: Make sure all cables and wires are not
pinched when raising or lowering display.
2. Position display at the desired height.
3. Tighten four height adjustment screws. (See Figure 8)
7
MSS6000
Installation Instructions
steps 1 through 7 above.
Display Swivel Stop Location Adjustment
The MSS-6000 allows for the installation of swivel stops
that limit the amount of display travel. Stops can be
installed at +/-15, 25 or 35 degrees.
To install swivel stops:
1. Follow steps 1 through 3 of Display Swivel Tension
Adjustment section.
2 deg. Max.
2. Insert one 10-24 X 1/2” Phillips head cap screw in one
of the three swivel stop holes (15, 25 or 35 degrees)
in the base of the stand. (See Figure 11)
Roll Adjustment Nuts
(2 places)
Tension Adjustment Screw
(Turn left to decrease tension
Turn right to increase tension)
NOTE: Adjustment nuts located between slide plate and
back plate of base assembly.
Figure 9
Display Swivel Tension Adjustment
Display swivel tension is pre-set at the factory. Swivel
tension will vary depending on the weight of display being
mounted.
Figure 10
If swivel tension adjustment is required:
1. Disconnect all cords and cables from display.
2. Follow steps in Removing Display from Mount
section.
3. Lay mount on back. (See Figure 10)
4. Locate three tensions adjustment screws.
(See Figure 10)
35 degrees
15 degrees
5. Turn each adjustment screw either clockwise to
increase tension, or counter-clockwise to decrease
tension.
NOTE: It is important that all adjustment screws are
turned equal amounts in the same direction for
the display to turn properly.
6. Install display following the instruction outlined in
Display Installation section on page 6.
25 degrees
7. Test display swivel tension by grasping each side of
display and turning display left and right.
Figure 11
If additional swivel tension adjustment is required, repeat
8
Installation Instructions
MSS6000
Option C
Cable Management
Option C uses the cable access at the center of the MSS-
6000 and then routes the cables down through an access
hole or slot in the mounting surface. (See Figure 14)
The MSS-6000 has been designed to provide multiple
cable management/routing options.
Option A
Option A does not use the cable access features of the
MSS-600 and simply routes the cables away from the
display and mount. (See Figure 12)
Cable
Access
Routed through access
hole in mounting surface
Figure 14
Cable
Access
Figure 12
Option B
Option B uses the cable access at the center of the MSS-
6000 and then routes the cables across the mounting
surface and out the rear cable access slot in the back of
the mount. (See Figure 13)
Cable
Access
Rear
Cable
Access
Slot
Figure 13
9
MSS6000
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Asia Pacific
A
Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
8800-000057 Rev. B
¤2008 Chief Manufacturing
03/08
P
F
+86-755-8996 9226
+86-755-8996 9217
|