RIGHT ANGLE DRILL ATTACHMENT
WITH 3/8” KEYLESS CHUCK
96996
ASSEMBLY AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SaVe THiS manual.
Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
1ꢀ.
Avoid unintentional starting. Be sure the switch on any power tool is in the Off position when not in
use and before plugging in. Do not carry any tool with your finger on the trigger, whether it is plugged in
or not.
13.
14.
Stay alert. Watch what you are doing, use common sense. Do not operate any tool when you are tired.
Take caution as some woods contain preservatives such as copper chromium arsenate (CCA)
which can be toxic. When cutting these materials extra care should be taken to avoid inhalation and
minimize skin contact.
15.
Check for damaged parts. Before using any tool, any part that appears damaged should be carefully
checked to determine that it will operate properly and perform its intended function. Check for alignment
and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may
affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified
technician. Do not use the tool if any switch does not turn On and Off properly.
16.
17.
Guard against electric shock. Prevent body contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerator enclosures.
Replacement parts and accessories. When servicing, use only identical replacement parts. Use of
any other parts will void the warranty. Only use accessories intended for use with this tool. Approved
accessories are available from Harbor Freight Tools.
18.
19.
Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking
prescription medicine to determine if your judgment or reflexes are impaired while taking drugs. If there
is any doubt, do not operate the tool.
Use proper size and type extension cord. If an extension cord is required, it must be of the proper
size and type to supply the correct current to the tool without heating up. Otherwise, the extension cord
could melt and catch fire, or cause electrical damage to the tool. Longer extension cords require larger
size wire. If you are using the tool outdoors, use an extension cord rated for outdoor use (signified by
“WA” on the jacket).
ꢀ0.
ꢀ1.
Maintenance. For your safety, service and maintenance should be performed regularly by a qualified
technician.
Use tools with both hands when required. Many tools such as chain saws, drills, routers, etc.,
require the use of both hands when operating. This helps maintain tool stability and keeps hands away
from the working area of the tool.
ꢀꢀ.
ꢀ3.
Always adhere to all warnings and safety precautions provided with the drill that this
Attachment is to be used with.
Read and adhere to all safety warnings and instructions provided in the manual of the power
drill being used with this Drill Attachment.
Note: Performance of this tool may vary depending on variations in local line voltage or tool battery power.
Extension cord usage may also affect tool performance.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction
activities, contain chemicals known [to the State of California] to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
-
-
-
Lead from lead-based paints
Crystalline silica from bricks and cement or other masonry products
Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to filter out microscopic particles.
(California Health & Safety Code 25249.5, et seq. )
SKU 96996
For technical questions, please call 1-800-444-3353
Page 3
Warning:The warnings, cautions, and instructions discussed in this instruction manual cannot cover all
possible conditions and situations that may occur. It must be understood by the operator that common
sense and caution are factors which cannot be built into this product, but must be supplied by the
operator.
Unpacking
When unpacking, check to make sure the parts listed on page 6 are included. If any parts are missing
or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible.
Operation
Refer to FIGURE 1 below and the Assembly Drawing on page 6.
Warning! Before attaching or removing the Drill Attachment, unplug the drill (not included) from the power
source. If it is a cordless drill, first remove the battery. If a pneumatic drill, disconnect it’s air supply.
1.
ꢀ.
Read and fully follow the manufacturer’s safety and operating directions for the drill (not included).
Open the chuck on the drill (not included), and insert the Shaft (8) securely into the chuck. Tighten the
chuck securely.
3.
4.
Thread the Handle (9) into the hole on either side of the Drill Attachment.
To install a Drill Bit, hold the Chuck Sleeve firmly in place and turn the Chuck counterclockwise. Insert
the shank of a bit (not included) all the way into the Chuck. While holding the Chuck Sleeve in place,
turn the Chuck clockwise to lock the Drill Bit in place.
5.
6.
Always use both hands while using this Attachment (one hand on the Handle (9) and the other hand on
the hand of the drill used with the Drill Attachment.) Operate the drill according to the manufacturer’s
instructions. Be careful to avoid letting the bit get stuck, as this will cause the Drill Attachment and drill
to twist, possibly causing injury.
After operation, unplug the drill (not included) from the power source. If it is a cordless drill, remove the
battery. Then, turn the Chuck (ꢀ) counterclockwise to open the jaws of the Chuck and remove the bit.
Chuck
Sleeve
FIGURE 1
Chuck (ꢀ)
Jaws of Chuck (ꢀ)
Handle (9)
Shaft (8)
Maintenance
1.
ꢀ.
Before each use, clean off the Shaft (8). Make sure it has no dirt, grease, or debris clinging to it.
Before each use, open the jaws of the Chuck (ꢀ) following the instructions above, and
remove any dirt, grease, or debris. Store it in a cool, dry location, out of reach of
children.
SKU 96996
For technical questions, please call 1-800-444-3353
Page 4
Assembly Drawing
9
Parts List
Part number
Description
Chuck Screw M5x16
Chuck
1
2
3
4
5
6
7
8
9
Chuck Casing
Bearing (2)
Gear (2)
Case (2)
Screw (5)
Shaft
Handle
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-
TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE
IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
SKU 96996
For technical questions, please call 1-800-444-3353
Page 5
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability
standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship
for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the
use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY
AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our
inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund
the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired
products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within
the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state
to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 96996
For technical questions, please call 1-800-444-3353
Page 6
|