Channel Plus Stereo Receiver 5115BID User Manual

P ER FOR M AN CE M ULTI-R OOM VIDEO  
WARRANTY  
5115 Modulator Series  
Multiplex Technology, Inc. warrants this product to be  
free from defects in materials and workmanship for a  
period of one year from the date of purchase or MTI will  
repair, or at its option, replace the defective product. To  
obtain warranty service, call MTI for a return material  
authorization (RMA) number and return the product pre-  
paid to Multiplex Technology, Inc., 3001 Enterprise  
Street, Brea, CA 92821, Attention: Customer Service.  
Please put the RMA number on the outside of the car-  
ton.  
Model 5115HHR  
Model 5115BID  
Model 5115PAL  
Any implied warranty arising from the sale of the prod-  
uct including implied warranties of merchantability and  
fitness for purpose are limited to the warranty stated  
above. MTI shall not be responsible for losses or dam-  
ages or expenses, whether direct, consequential or inci-  
dental arising from the use of or the inability to use this  
product. Some states do not allow limitations on how  
long the implied warranty lasts or the exclusions or limi-  
tations or incidental or consequential damages, so the  
above limitations and exclusions may not apply to you.  
This warranty gives you specific legal rights, and you  
may have other rights which may vary from state to  
state.  
714-996-4100 * 800-999-5225 * fax 714-996-4900 * www.channelplus.com  
600-132 Rev.A  
©1999 Multiplex Technology, Inc., Brea, Ca.  
 
Installation of the wall plate  
Connecting A Video Source  
Using any video source, DVD,Satellite or VCR connect it to the wall  
plate as shown. This video source will be transmitted over the Cat 5  
wire to the channel injector.  
Step Two  
The wall plate mounts using a low voltage ring into a wall cut out.  
Run a line of Cat 5 wire from the wall plate to the channel injector  
and connect wires as shown.  
Optional loop  
out television  
or a/v receiver  
connections  
*
Side view  
of wall plate  
Audio/video  
note:  
When using Cat 5 wire  
remove the default resistor  
that is in pins 3 and 4 of the  
wall plate screw terminal  
Out to  
TVs  
Cat 5 wire  
Video source  
pin  
1
Coax jumper  
Bl/W  
2 Blue  
3 Org/W  
4 Orange  
5 Gr/W  
6 Green  
Antenna or  
CATV feed  
Default  
resistor  
7
Br/W  
8 Brown  
*Use the NORM / LOOP switch to select the proper setting for your  
application.  
pin  
1
2 Red  
note:  
Green  
When using quad wire connect  
wires only to pins 1, 2, 5 and 6.  
Leave the resistor in place  
at pins 3 and 4.  
5 Black  
6 Yellow  
Norm/Loop  
switch  
At the channel injector, connect Cat 5 wire as shown. Follow the  
color coding on the screw terminal.  
NORM:  
Select NORM when a television or a/v receiver is not used at the wall  
plate to view the connected source.  
When using only quad wire  
use positions 1, 2, 5 and 6  
and follow color coding.  
LOOP:  
Select LOOP when a television or a/v receiver is connected to the  
wall plate to view the connected source  
blue/white  
pin 1  
blue/white  
pin 1  
run the Cat 5 wire  
through the grommet at the  
bottom of the injector  
4
5
 
Method Two: Use the power injector to apply power along the Cat  
5 or quad wire run. Cut the connecting wire along the run and insert  
the power injector. Connect the wires using the color coding. Then  
plug the power supply into the power injector.  
Applying Power and Programming  
Step Three  
The 5115 series has three different methods for applying power  
to the system.  
Us e o n ly o n e m e th o d fo r a p p lyin g p o w e r.  
power injector  
Method One: Apply power directly to the channel injector with the  
power supply.  
power supply  
pin 1  
blue/white  
power supply  
cut Cat 5 wire  
power plug  
Lower right of  
channel injector  
The green LED in the upper right corner of the channel injector will  
be lit showing power is active.  
Power plug  
Method Three: Apply power directly at the wall plate.  
The green LED in the upper right corner of the injector will be lit  
showing power is active.  
The green LED in the lower  
right corner of the wall plate  
and upper right corner of the  
channel injector will be lit  
showing power is active.  
(See power length requirements page 8)  
power plug  
7
6
 
Power Length Requirements  
How to Program  
Method One  
Determine which unused channel you want to view your video  
source on and program the injector for that channel. There must be  
one unused channel both before and after the selected channel to  
avoid interference. The new channel will be combined with the exist-  
ing channels and appear on all televisions.  
Up to 300’ of  
Cat 5 or quad  
wire maximum  
Upper right corner on  
channel injector  
power plug  
green LED  
programming button  
Power Length Requirements  
Method Two  
To program: For example channel 60  
Up to 100’ of  
Cat 5 or quad  
wire maximum  
1: Press the button 6 times.  
2: Wait for the LED to relight.  
3: Press the button 10 more times (pressing 10 times enters “0”).  
The injector will now combine the wall plate feed on channel 60 with all other  
existing channels from the incoming CATV or antenna.  
Up to 300’ of  
Cat 5 or quad  
wire maximum  
power plug  
To program a three digit channel: For example channel 120  
1: Press the button 1 time.  
Power Length Requirements  
Method Three  
2: Wait for the LED to relight.  
3: Press the button 2 more times.  
4: Wait for the LED to relight.  
Up to 100’ of  
Cat 5 or quad  
wire maximum  
5: Press the button 10 more times.  
Finding Unused Channels  
CATV: Determine the highest channel number delivering a picture,  
excluding 95-99. Tune the TV up one channel at a time from the last  
channel with a picture until finding one channel with no trace of a  
picture or interference, just snow.  
power plug  
Antenna: Tune the TV one channel at a time from channel 14-64.  
Locate one channel that has no trace of a picture or interference,  
just snow.  
8
9
 
Programming a New Channel  
Valid channels are 14 thru 64 for UHF and 65 thru 125 for CATV  
Channels 95-99 are not available. Channels 21 thru 62 are for Pal.  
Specifications: typical @ 25°C 5° C  
5115HHR / 5115BID  
NTSC  
1.0 V peak-to-peak @ 75  
5115PAL(AUS)  
Channel Spacing:  
Skip at least one number between the new channel and the closest  
existing UHF/CATV channel.  
(example 14 and 16: OK 14 and 15: Unacceptable)  
video input format  
input signal  
CCIR  
output  
12dBmV normal - 15.5dBmV maximum  
3 RCA (video + audio left + audio right)  
3 RCA (video + audio left + audio right)  
75or > 1 Min “loop” position (selectable)  
Error Indication:  
If an error occurs or an incorrect channel is entered, the LED will  
flash quickly for one second and return to previous settings.  
input connectors  
loop-thru connectors  
video termination  
tuning range UHF  
CATV  
Cable HRC and IRC considerations:  
14 to 64  
21 to 62(28 to 67)  
Most cable services use IRC frequency assignments. This is the  
default for the 5115. However, if the cable services uses HRC or  
the TV appears to search for the “created channel”, program the  
channel injector for HRC.  
65 to 125A  
power supply  
included with product  
210 to 250  
mains power  
105 to 125  
Fo r H RC e n te r 9 8 . Re s e t to IRC b y e n te r in g 9 9 .  
output of power supply  
15VDC 600mA  
Entries 98 and 99 are for setting HRC or IRC only. They will not  
change the channel number.  
general  
With programming complete, test each TV in the system to see that it is  
receiving the new channel.  
width x height x depth  
injector module  
6.5” x 3.5” x 1.25”  
wall plate  
1.25” x 4.0” x 1.75”  
(16.3cm x 9cm x 3.2cm)  
(3.2 cm x 10.5cm x 4.0cm)  
shipping weight  
2 lbs (0.9 kg)  
–4°F to 131°F (–20°C to 55°C)  
operating temperature  
A excluding channels 95 through 99  
10  
11  
 

Blaupunkt Car Video System IVMR 7001 User Manual
BMW Headphones BLUETOOTH WIRELESS HEADSET User Manual
Bose Headphones MIE2I User Manual
Brother Photo Printer DCP 135C User Manual
Calvin Klein Pressure Washer PW0881801 User Manual
Cannon Electric Pressure Cooker 10460G User Manual
Canon All in One Printer MX432 User Manual
Casio Watch ID 14 User Manual
Chicago Electric Saw 91938 User Manual
Chicago Electric Welder 8878 User Manual