Model MUOTIU-EX
Outdoor Multi-Unit Telephone Interface
Step 2
Overview
The Outdoor Multi-Unit Telephone Interface uses a
900 Mhz secure digital radio link that allows secure
conversations and gate operator control.
The Outdoor Multi-Unit Telephone Interface
(MUOTIU-EX) is compatible with various Liftmaster
Wireless Products.
Carton Inventory
Mount to solid surface.
Test/Program Cord
Wiring to AC Adapter
Outdoor Multi-Unit Telephone
Interface (MUOTIU-EX)
Remove bottom panel
of the MUOTIU-EX.
AC Adapter
Antenna
ACTIVE POWER
Line IN
Line OUT
PWR GND
Assembly & Installation
Choose location near the de-mark location.
Step 1
Connect the Solid Black Wire to the GND Terminal
(shown below).
Connect the Striped Wire to the +18V Terminal
(shown below).
Power
Active
LINE
PHONE
TIP
GND
+18V
TIP
RING
RING
Screw in antenna.
Use the supplied Test/Program Cord for programming
and testing before completing connections to phone
company’s de-mark box.
1
MUOTIU-EX is not getting expected transmission
range.
PIN Number Functions
Number
Function
When used in buildings with stucco or cement walls,
the range is greatly reduced. The Repeaters can be
used close to the building to solve this problem.
Keep MUOTIU-EX away from trees, metal objects,
masonry, computers, and any other “Radio Noise
Source”. Radio devices that run on 900 Mhz also
affect range. Turn them off and see if reception has
improved.
*#(00-63)#(Phone Number)# Program number
**01*****
**03#(00-63)#
**07
Erase ALL numbers
Erase ONE number
Activate the
MUOTIU-EX
Verify Call Forwarding
Number
**06#(00-63)#
Keep antenna vertical.
**#8
*9
Clear memory
Activate gate
After dialing “*9” a beep is heard, then an error
tone.
Check batteries in GCU.
Canada
NOTE: For use with version 7 and higher.
Will not accept command after dialing “**”.
Check the line and telephone connections.
To enable Canadian Mode press “**13”. To disable
Canadian Mode press “#*16”. The Canadian
programming numbers are shown in the table below:
Telephone does not ring when Call button is
pressed.
Number
Function
If the Active LED on MUOTIU-EX flashes after Call
button is pressed, check telephone connections and
verify that the phone number is correct.
If the Active LED on MUOTIU-EX does not flash after
the Call button is pressed, see Programming
Accessories to ensure MUOTIU-EX is programmed
correctly.
##(00-63)#(Phone Number)# Program number
#*01*****
#*03#(00-63)#
#*07
Erase ALL numbers
Erase ONE number
Activate the
MUOTIU-EX
#*06#(00-63)#
Verify Call Forwarding
Number
NOTE: If the channels are changed all devices in the
network need to be erased and reprogrammed.
#*#8
#9
Clear memory
Activate gate
There is a buzzing or failed connection when call
is answered.
Move MUOTIU-EX away from phone and/or
computer. Try changing channel of MUOTIU-EX and/
or the channel on the MUGAPLM (see Multi-Unit Gate
Access Panel manual).
Troubleshooting
Dial tone is not heard after connecting to the
MUOTIU-EX.
Check phone connections. If it is a two-line phone
ensure it is on Line 1.
Only first couple of words from caller are heard.
Lower the MUGAPLM microphone sensitivity (see
Multi-Unit Gate Access Panel manual).
If a dual-tone error tone is heard when trying to open
gate, ensure MUOTIU-EX is programmed to the
correct MUGAPLM. Check that gate operator has
been taught to master unit as well.
If MUOTIU-EX has already been programmed it will
need to have memory cleared (see below).
Memory needs to be cleared.
Clearing MUOTIU-EX memory will not clear any
MUOTIU-EX settings or programmed phone numbers.
To clear memory, dial “**#8” on the telephone
connected to the MUOTIU-EX. A beep will be heard.
When dialing numbers a dial tone is heard.
All numbers and symbols must be dialed within 3
seconds of each other, otherwise the MUOTIU-EX
times out and returns to dial tone.
3
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:
1-800-528-2806
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited,
except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
© 2008, The Chamberlain Group Inc.
All Rights Reserved
114A3698
|