Carson Manufacturing Co., Inc.
5451 North Rural Street
Indianapolis, IN 46220
Phone: (888) 577-6877 Fax: (317) 254-2667
SA-441-17
DUAL REMOTE SIREN AMPLIFIER
WITH MECHANICAL TONE
O
O
F
N
F
RADIO
DUAL
PA
SIREN
VOL
STBY
MECH
WAIL
SA-441
ON
YELP
POWER
PHASER
INSTALLATION AND OPERATING
INSTRUCTIONS
Carson is a trademark of Carson Manufacturing Company, Inc.
Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage.
Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity.
(Ref. OSHA 1910.95 for occupational noise exposure guidelines)
SA-441-17 Installation and Operating Instructions
Page 3 of 15
SPECIFICATIONS
Input Voltage
Input Current
Standby Current
Audio Frequency
Audio Distortion
Audio Output
11 - 16 VDC (negative ground)
17 AMPS (@14 VDC - dual 100W speakers)
Less than 250 mA
200Hz - 10 kHz + 3db
Less than 3% (@1 kHz - dual 100W speaker)
80 watts (@14 VDC - dual 100W speaker)
400 ohms + 10%
Audio Input
Output Power
Siren Frequency
210 WATTS RMS MAX. (15 VDC - dual 100W speakers)
700Hz - 1500Hz (Mechanical 700Hz – 1600Hz)
Two-Tone = 435Hz & 585Hz
Tones / Cycle Rates
Mech
6 CPM
Wail
13 CPM
Yelp
190 CPM
Phaser
15 CPS
Two-Tone
60 CPM
High Voltage
Protection
16 - 18 VDC will cause siren output to cease, resume at normal
Short Circuit Current 50 AMPS (supply circuit must be capable of supplying this)
Operating
Temperature
Controls
-15° F to +140°F
6-position rotary selector switch (Radio, Standby. Mechanical, Wail,
Yelp, and Phaser).
Dual siren control toggle switch.
Momentary push-button Siren switch.
Front panel mounted PA volume control, Radio adjust on amplifier
Auxiliary input for positive or negative connection.
8-position DIP switch option selector.
Connections
(10-Pin Conn)
Size
(2) Positive, (2) Negative, (3) Speaker, (2) Radio, Control
Control Head: 6-1/4" W x 2-7/8" H x 1" D
Amplifier: 8” L x 6-3/4” W x 2-1/8” H
6 LBS.
Weight
NOTICE
Due to continuous product improvements, we must reserve the right to change any specifications and
information, contained in this manual at any time without notice.
Carson Manufacturing Co., Inc. makes no warranty of any kind with regard to this manual, including, but not
limited to, the implied warranties of merchantability and fitness for a particular purpose.
Carson Manufacturing Co., Inc. shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this manual.
07/29/08
CP5008A
Page 4 of 15
SA-441-17 Installation and Operating Instructions
GENERAL DESCRIPTION
The SA-441 Dual Siren Amplifier with Mechanical Tone is a premium unit designed for dual
100W speaker use. The control head is only 1 inch deep and can be installed in minimum
clearance areas. Connection between the control head and amplifier is via a single lead wire
with common ground.
A 6-position rotary selector switch controls the primary operating modes of Radio, Standby,
Mechanical, Wail, Yelp, and Phaser. A Dual siren control switch provides additional modes,
including dual Mechanical, Wail and Yelp, Yelp and Mechanical, and Phaser and Mechanical.
Two-Tone may optionally replace Phaser. A Siren push-button switch is provided for Manual
control of the output tone or Horn override, depending on the selector switch and option switch
settings. An independent toggle switch controls power. A hole is provided in the amplifier to
adjust Radio volume.
Depending upon the version, the microphone may or may not be directly mounted to the
control head. Units with an “F” suffix have the microphone permanently mounted to the
faceplate. Units with an “FX” suffix are provided with an extension harness and connectors for
remote mounting of the microphone.
An auxiliary input is provided for connection to a positive or negative horn ring circuit or switch,
performing the same function as the Siren push-button.
An 8-position DIP switch on the amplifier allows selection of various options: Two-Tone to
replace Phaser, Manual Mechanical, Manual Wail, and Horn Ring Cycler 2 (HRC2), which
allows cycling through Mechanical, Wail, Yelp, and Phaser by tapping the horn ring when the
function switch is in the Standby position. The front panel is backlighted with LED's for night
visibility.
This durable unit utilizes short circuit, high voltage, and reverse polarity protection systems for
maximum service life over a wide temperature range. Two separately fused amplifiers provide
redundancy, and the unit will operate with only one amplifier functioning.
CP5008A
07/29/08
SA-441-17 Installation and Operating Instructions
Page 5 of 15
INSTALLATION
Proper installation of the unit is essential for years of safe, reliable operation. Please read all
instruction before installing the unit. Failure to follow these instructions can cause serious
damage to the unit or vehicle and may void warranties.
SAFETY PRECAUTIONS
For the safety of the installer, vehicle operator, passengers and the community please observe
the following safety precautions. Failure to follow all safety precautions and instructions
may result in property damage, injury or death.
Qualifications - The installer must have a firm knowledge of basic electricity, vehicle electrical
systems and emergency equipment.
Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage.
Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity.
(Ref. OSHA 1910.95 for occupational noise exposure guidelines)
Mounting - Mount the control head for easy access by the vehicle operator. DO NOT mount
in air bag deployment area. Assure clearances before drilling in vehicle.
Wiring - Use wiring capable of handling the current required. Make sure all connections are
tight. Route wiring to prevent wear, overheating and interference with air bag deployment.
Install and check all wiring before connection to vehicle battery.
Testing - Test all siren functions after installation to assure proper operation. Test vehicle
operation to assure no damage to vehicle.
Keep These Instructions - Keep these instructions in the vehicle or other safe place for future
reference. Advise the vehicle operator of the location.
UNPACKING
Inspect contents for shipping damage. If found alert carrier immediately.
Contact supplier immediately if any components are missing.
Contents should include the following items:
Complete Unit
Qty Item
-17F -17FX
1
1
1
1
1
1
1
1
1
Amplifier, Remote (SA-441-17F or FX)
X
X
X
X
X
X
X
X
X
Bracket, Microphone Clip with mounting screws (CP3633)
Connector, 10-P Terminal Block Plug for Amplifier (CP4833-10)
Cable Assembly for Control Head, 5-P (CP3040)
Control Head with attached Microphone (SA-441-17CH)
Control Head without Microphone (SA-441-17CHX)
Cable, Microphone Extension 18FT (CP3850)
X
X
X
X
Microphone, Detachable Noise Cancelling (ES00028-10)
Instruction Manual (CP5008 This Manual)
X
Amplifier Only
Qty Item
1
1
1
Amplifier, Remote Only (SA-441-17AMP)
Connector, 10-P Terminal Block Plug for Amplifier (CP4833-10)
Instruction Manual (CP5008 This Manual)
07/29/08
CP5008A
Page 6 of 15
SA-441-17 Installation and Operating Instructions
OPTION SWITCHES
An 8-position DIP switch on the remote amplifier may be changed to select various options.
Option Switches
On Remote Amp
8
7
6
5
4
3
2
1
ON
Option Switches
Default Setting (Shown) all OFF (UP)
SW-1 Two-Tone - Turn this switch on to replace Phaser tone with Two-Tone.
SW-2 Mechanical Override - Pressing the Siren push-button normally produces Horn tone
while the rotary function switch is in Mechanical. Turn this switch on to manually override
Mechanical tone instead.
SW-3 SW-4
Siren push-button and Auxiliary Input Function
with Rotary Selector Switch in Standby
OFF
ON
OFF (Default) Produces Horn tone while pressed.
OFF Manual control of Mechanical tone.
Also Mechanical tone continues to fall when Rotary
Selector Switch is changed from Mechanical position.
OFF
ON
ON
ON
Manual control of Wail tone.
Activates Horn Ring Cycler 2 (HRC2) function.
SW-5 thru SW-8 - Not Used… Leave Off.
Horn Ring Cycler 2 (HRC2) - Turn on DIP SW-3 and SW-4 to enable this feature. Also
connect the auxiliary input to the horn ring or other switch. While the siren is in standby, tap the
horn ring to bring the unit out of standby into Mechanical tone. Repeatedly tapping the horn
ring will cycle through Mechanical, Wail, Yelp, and Phaser tones. Tapping the horn ring twice
quickly will stop the siren tones and return the unit to standby. Pressing and holding the horn
ring will produce Horn tone until released. Then the siren will return to its previous siren tone or
standby.
Dual Mode version of HRC2 sequences as described in the following table.
Sequence (Loops)
Dual HRC2
Spkr 1 Spkr 2
Mechanical Mechanical
|
|
|
I
V
Wail
Yelp
Yelp
Mechanical
Mechanical
Phaser
CP5008A
07/29/08
SA-441-17 Installation and Operating Instructions
Page 7 of 15
MOUNTING – Amplifier
Select a location for the amplifier in an area such as the driver compartment firewall, under a
seat, etc. Mounting the amplifier in the engine compartment or in an area directly exposed to
weather is not recommended. Assure adequate ventilation to prevent overheating. Allow
clearance for wiring and radio adjustment. Inspect behind mounting area for clearance. Mark
the location of the mounting holes to be drilled.
Drill 4 holes (up to 1/4" diameter) to mount the amplifier to the vehicle. Install the terminal
block plug and make all electrical connections before final mounting (See ELECTRICAL
CONNECTIONS – Amplifier). The plug is secured with the two locking screws. Then mount
the amplifier to the vehicle using appropriate hardware (not supplied).
MOUNTING – Control Head
Select a mounting location in an area such as the dash or overhead console. Choose a
mounting location convenient to the operator and away from any air bag deployment areas.
Inspect behind mounting area for clearance. Allow 1¾” of depth to accommodate the control
head and cable(s). Consider wire routing and access to connections, as well as microphone
bracket placement.
Use template (back page) for marking hole and cutout locations. Connect control head cable
to back of unit and route leads through cutout. Make all electrical connections (See
ELECTRICAL CONNECTIONS – Control Head), and then use #6 screws for mounting the
control head (not supplied).
MOUNTING - Microphone Extension Harness (“FX” model only)
Select
microphone connector, verifying adequate
cable length. Allow 1-3/4" clearance
a
mounting location for the
Control Head – Rear View
Microphone
behind connector to prevent sharp bends in
the harness. Drill or punch a 5/8" diameter
hole for mounting. Remove mounting nut
and washer from connector. Insert the
connector into the hole and secure it using
a 3/4" socket to tighten the nut. Connect
harness to the control head as shown prior
to final installation of head.
Extension
Cable
07/29/08
CP5008A
Page 8 of 15
SA-441-17 Installation and Operating Instructions
ELECTRICAL CONNECTIONS - Amplifier
Electrical connections to the amplifier are made using a terminal block plug located on the
amplifier. A label on the unit identifies each terminal function. You should install the plug on
the unit before wiring. If the unit needs service the plug can be easily removed without
unwiring. The power supply of the unit must be capable of delivering peak currents up to 50
amps for adequate short circuit protection and reliable operation. The preferred source is
directly at the vehicle battery. The amplifier is fused near connector.
Attach leads by stripping 3/8", inserting into connector and clamp by tightening screw. Make
sure the screw is tight and the wire can't be pulled out.
Failure to adequately tighten the screw can result in improper operation or burning the
connector and wire.
Wire Size and Termination - The diagram shows the minimum wire size used for each
connection, along with recommended lead color. If the wire is longer than 10 ft. use the next
larger wire size. The power lead pairs can be extended with single #10 AWG lead wire. Use
only high quality crimp connectors for installation on the vehicle.
Please note that three leads are connected to the speakers – one common lead to the
negative of both speakers and one lead to each positive speaker terminal. This is necessary
for proper operation.
Optional Radio Input Connection - Connect one lead to each terminal of the radio speaker
or output connector. The input is isolated and polarity is not important. May need to set
RADIO VOLUME ADJUST on side of amplifier.
ELECTRICAL CONNECTIONS – Control Head
All control head leads can be extended with #22 AWG or larger lead wire.
Black: Negative - Connect to same ground or negative supply as amplifier.
Red: Positive - May be connected to +VDC supply. It is recommended that the lead be
connected to the accessory output of the fuse block. This provides additional protection of a
fused input to the control head.
Yellow: Lights - This lead may be connected to the dash lights or to the red power lead.
Connecting to the dash lights will turn on the panel lights whenever the dash lights are on.
When connected to the red lead, make sure that the ignition switch controls the power to that
connection. This prevents the panel lights from being continuously on.
White: Control - Connect white leads from amplifier and control head. Route this lead away
from the transmitter antenna lead to prevent R.F. interference being fed to the siren amplifier.
Green: Auxiliary Input - Used for Siren control. Performs same function as Siren button.
Connect to a normally open switch or to horn ring circuit. Circuit may connect to either positive
or negative. When connected to horn ring circuit, use a SPDT switch to connect horn ring to
either vehicle horn or to manual control circuit.
NOTE: Permanent disconnection of the vehicle horn is NOT recommended.
NOTE: Be sure to cut lead short if not used and insulate with electrical tape.
CP5008A
07/29/08
SA-441-17 Installation and Operating Instructions
ELECTRICAL CONNECTIONS CONTINUED
Page 9 of 15
Horn
Circuit
HORN RLY
Vehicle
Horn
+VDC
or
Momentary
SPST
Auxiliary Input
Connection
Examples
-VDC
Switch
Splice
+VDC
or
-VDC
May need to
add diode
(10mA current)
Added
SPDT
Switch
or
Aux input is
activated with
+VDC AND -VDC
Note:
Vehicle horn will also
sound with siren
Vehicle
Horn
To
AUX
To
AUX
To
AUX
Control Head Cable may be
extended with #22AWG Wire
(AUX) Auxiliary Input
Control Head
Rear View
Green Wire
Control Head
Optional
Microphone
Extension
Cable
Cable (CP3040)
Backlighting Yellow Wire
Control Line to Amplifier
-VDC
White Wire
Black Wire
Red Wire
Customer Fused +VDC
Connect to
output jack, terminals
or speaker of radio
#22 AWG BLU
#22 AWG WHT
To Control Head White Wire
RADIO
#18 AWG ORG
#14 AWG RED
(2 LEADS)
-
100W
Speaker
#18 AWG ORG/BLK
BAT
#18 AWG BRN
-
100W
Speaker
-
#14 AWG BLK
(2 LEADS)
#18 AWG BRN/BLK
Plug secured with mounting screws
15A Automotive Type Fuses
10-P Terminal Block Plug
(CP4833-10)
Plug installed
this orientation
SPKR B AMP
SPKR A AMP
Plug into unit first for
terminal identification
Remote
Amplifier
07/29/08
CP5008A
Page 10 of 15
SA-441-17 Installation and Operating Instructions
OPERATION
Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage.
Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity.
(Ref. OSHA 1910.95 for occupational noise exposure guidelines)
GENERAL
This unit is designed for easy operation under the stress associated with high-speed pursuit.
Most siren functions are accessible with one simple motion without repetitive activation of
switches or automatic timed switching that can interfere with desired operation.
SELECTOR SWITCH
The 6-position rotary selector switch controls the primary operating mode of the siren.
Radio - Also known as Radio Repeat, this function amplifies
SELECTOR SWITCH
a radio speaker input for re-broadcast outside the vehicle.
The radio must be connected and RADIO VOLUME
ADJUSTed for this mode to function.
Standby - A silent mode that may be overridden anytime with
the Siren push-button.
RADIO
STBY
MECH
WAIL
Mech - A simulated mechanical siren tone used anytime.
Wail - A slower changing tone used on highways.
Yelp - A rapidly changing tone used in congested areas.
Phaser - A very rapidly changing tone used at intersections
or in highly congested areas. May be optionally replaced with
Two-Tone which is two alternating frequencies like a
European HI-LO. See OPTION SWITCHES section.
YELP
PHASER
With the Dual switch OFF, the following functions are available:
Rotary
Switch
Radio
Operating Activate Siren push-button or Auxiliary Input
Mode
Radio
No Change
Standby Silent
Horn (Default) or Manual Mech or Manual Wail or HRC2
(See SIREN SWITCH section)
Mech
Wail
Yelp
Mech
Wail
Yelp
Horn (Default) or Manual Mech (See SIREN SWITCH section)
Horn
Horn
Horn
Phaser
Phaser
MICROPHONE (PA Override)
The noise-canceling microphone is used for public address operation and overrides any
function when the push-to-talk button on the side of the microphone is pressed.
PA VOL
This control adjusts the PA volume. With the vehicle parked, set the PA
volume to the maximum level with no feedback (squeal).
PA
VOL
CP5008A
07/29/08
SA-441-17 Installation and Operating Instructions
Page 11 of 15
SIREN SWITCH
This momentary push-button switch provides Horn or Manual tone control.
It can optionally control Horn Ring Cycler 2 operation in the Standby position
if the HRC2 option is selected.
SIREN
Horn - A simulated Air-horn tone momentarily sounded.
Manual Wail - Manual control of Wail tone rise and fall.
Manual Mech - Manual control of Mech tone rise and fall.
The Siren push-button optionally provides the following function while in Standby mode.
See OPTION SWITCHES section.
DIP
SW-3 SW-4
DIP
Siren push-button and Auxiliary Input Function
with Rotary Selector Switch in Standby
OFF
ON
OFF (Default) Produces Horn tone while pressed.
OFF Manual control of Mechanical tone.
Also Mechanical tone continues to fall when Rotary
Selector Switch is changed from Mechanical position.
OFF
ON
ON
ON
Manual control of Wail tone.
Activates Horn Ring Cycler 2 (HRC2) function.
AUXILIARY INPUT
During installation an auxiliary input may be connected to the horn ring or other switching
device. It provides the same operation as pressing the Siren push-button.
HORN RING CYCLER 2 (HRC2)
During installation, the auxiliary input must be connected and the HRC2 option selected. While
the siren is in standby, tap the horn ring for different tones.
See OPTION SWITCHES section for further details.
RADIO VOLUME ADJUST
Radio Volume
The radio repeat volume level is set using an adjustment on the side
of the amplifier. Set the Selector Switch to the Radio position and
turn on the power. With the radio volume itself set to a normal level,
set the siren radio volume adjust control to the desired level.
DUAL SWITCH
O
O
F
The Dual switch controls the signal to the two amplifiers. With the switch off,
the amplifiers produce a common signal to the speakers. With the switch on,
independent siren signals are produced by each amplifier as follows:
N
F DUAL
Rotary Switch Operating Mode Activate Siren push-button or Auxiliary Input
Spkr A Spkr B Spkr A and B
Radio No Change
Silent
Radio
Standby
Mech
Wail
Yelp
Phaser
Horn (Default) or Dual Man Mech or Dual Man Wail or HRC2
Horn (Default) or Dual Manual Mech
Horn
Horn
Horn
Mech
Wail
Yelp
Mech
Yelp
Mech
Phaser Mech
07/29/08
CP5008A
Page 12 of 15
SA-441-17 Installation and Operating Instructions
SERVICE
This unit is designed to provide years of reliable service under even the worst conditions.
Many times there may appear to be a problem with the unit when the true problem is in the
speaker(s) or improper installation. The following chart shows typical symptoms and possible
causes.
A blown amplifier fuse doesn't necessarily mean that the unit is bad. If a speaker or speaker
lead is shorted this fuse will blow before the unit is damaged. Disconnect the SPKR leads and
replace the fuse. If the siren emits a sound when in the Yelp position it is OK. Check the
speaker(s) or leads for possible shorting.
PROBLEMS
Symptom
Possible Cause
Check
Does backlighting and power indicator on control head
come on?
No power or Power switch not turned on
siren output Bad speaker(s)
Connector loose
Do you hear a "pop" when turned on?
Amplifier/control head fuse blown Is an external fuse or circuit breaker used?
Loose connection at power source Are the negative leads connected to a good ground?
No siren tone High Voltage Protection
- PA works Mic button stuck
Input voltage must be less than highest rated voltage.
Does mic button release properly?
No PA
Distorted
PA volume not set properly
Speaker assembly loose
Have you tried turning the PA volume control?
Is the speaker bell or tip loose?
siren sound Intermittent Aux Input connection Is the Aux Input used and wired properly?
Low vehicle voltage
Intermittent High Voltage Protection
Input voltage must be greater than lowest rated voltage.
Is the vehicle voltage regulator working properly?
Are connections tight on the amplifier/control head?
Is there a loose connection on a power lead?
Is something lying on the microphone?
siren tone
Connector loose
Bad power connection
Mic button activation
Circuit breaker in supply connection
Is a circuit breaker used with at least a 50A rating?
Horn function Siren switch stuck
Does the Siren switch return fully when released?
Or Manual Aux Input improperly connected Is the Aux Input used and wired properly?
stuck on
No Radio
Unit not connected to radio
Radio volume too low
Is the radio connected properly to the unit?
Can you here the radio in the vehicle?
Have you tried turning the radio volume control?
Is the T-T option switch turned on?
Are Control head and amplifier connected to good
ground?
Wrong siren Two-Tone option installed
tone Ground system noise
Dual switch Only one amplifier working
doesn’t work One speaker damaged
Constantly Amplifiers wired incorrectly
blows fuses
Is one fuse on the amplifier blown?
Have you tried replacing the speaker?
Are SPKR A and SPKR B wired together?
or contact our Service Department at:
CP5008A
07/29/08
SA-441-17 Installation and Operating Instructions
Page 13 of 15
PARTS and ACCESSORIES
The following parts and accessories are available from Carson Manufacturing Company, Inc.:
Part
CP3965
CP4732
CP4834
CP4812
Description
Button, Switch Cap Black (for Siren pushbutton)
Control, 1K Vertical Trimmer (Amplifier)
Control, 1K Ohm Vertical Mini-Pot (Control Head PA)
Cover, Amplifier (Does not include Chassis)
Cover, Control Head back
CP3880
ATO/ATC 15A
CP4852
Fuse, 15 Amp Automotive
Knob, Selector Switch Knob
CP4853
Knob, PA Volume Control
CP5009
Label, SA-441-17 Front Panel
CP4750
SR-15-1
CP5014
8121D2V40
7101-T-C-Q
SS2846
Microphone, Noise Canceling w/Connector
Microphone Strain Relief
Nut, 1/4-40 Dress (for Siren pushbutton)
Switch, Momentary Push Button, Vertical (Siren pushbutton)
Switch, Power Toggle
Switch, Mini Toggle (Dual switch)
Switch, Rotary 6-Pos. Selector, Vertical
Transistor, Output (2 required)
CP3599
CP4119
Accessory
CP4872
Description
Bracket, Control Head Console Mounting
* - standard accessory supplied with unit F or FX model
CP3633 *
Bracket, Microphone Clip with mounting Screws
CP3040 *
Cable, 5-P Control Head Lead Assembly
ED1758
CP3850 *
Cable, 10-P Amplifier Lead Assembly 8FT (made w/ CP4833-10 Conn)
Cable, Microphone Extension 18FT for FX model
CP4833-10 *
ES00028-10 *
SA-441-17AMP
SA-441-17CH *
Connector, 10-P Terminal Block Plug w/Locking Screws
Microphone, Detachable Noise Canceling for FX model
SA-441-17 Remote Amplifier (includes CP4833-10 Connector)
SA-441-17 Control Head with attached Microphone for F model
SA-441-17CHX * SA-441-17 Control Head without Microphone for FX model
CP5008 *
Manual, SA-441-17 Instruction
or contact our Service Department at:
07/29/08
CP5008A
Page 14 of 15
SA-441-17 Installation and Operating Instructions
RETURN
If you have any questions concerning this or any other Carson product, please contact our
Technical Service Department at (888) 577-6877. Many issues can be handled over the
If a product must be returned for any reason, please contact our Technical Service Department
to obtain a Returned Merchandise Authorization number (RMA#) before you ship the product
to Carson. Please write the RMA# clearly on the package near the mailing label. Be sure to
provide a return address, contact and phone number, along with a brief description of the
problem.
LIMITED WARRANTY
Carson Manufacturing Company, Inc. warrants this new product to be free from defects in
material and workmanship, under normal use and service, for a period of five (5) years
from the date of delivery to the first user-purchaser.
During this warranty period the obligation of Carson Manufacturing is limited to repairing
or replacing, as Carson Manufacturing may elect, any part or parts of such product which
after examination by Carson Manufacturing is determined to be defective in material
and/or workmanship.
This warranty does not cover labor charges for removal or re-installation of the product.
Fuses and lamps are not covered under this warranty.
This warranty does not extend to any unit that has been subjected to abuse, misuse,
improper installation or which has not been adequately maintained, nor to units which
have problems related to service or modification at any facility other than the
manufacturer.
THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT
NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL CARSON MANUFACTURING
COMPANY, INC. BE LIABLE FOR ANY LOSS OF PROFITS OR ANY INDIRECT OR
CONSEQUENTIAL DAMAGES ARISING OUT OF ANY SUCH DEFECT IN MATERIALS
OR WORKMANSHIP.
CP5008A
07/29/08
SA-441-17 Installation and Operating Instructions
Page 15 of 15
CONTROL HEAD INSTALLATION TEMPLATE
07/29/08
CP5008A
|
