Fig. 1 …Assembley
(A)screw
Mounting Hanger for Low Ceilings
Assembly and Installation Instructions
C om patible projector m odels
Phillips head hex bolt
with integrated spring
washer and flat washer
M6×12 (×4)
projection direction
LV-7545
※
Attach the bracket
so that the arrow is
pointing in the
Ceiling bracket
(×1)
Projector bracket (×1)
LV-CL07
Be sure to consult with a qualified installation specialist.
projection direction
(toward the front of
the projector).
Projector
(B)screw
Phillips head machine screw
with integrated spring washer
and flat washer M3×8 (×4)
This mounting hanger is specifically for use with our projectors listed on above. Do not use for any
other equipment or purposes. Be especially careful that children do not hang from it. Perform proper
assembly and installation by following these instructions. Be sure to follow all precautions.
(A)screw
Phillips head hex bolt with
integrated spring washer
and flat washer M6×12 (×4)
When hanging a projector from the ceiling using this mounting hanger, the ceiling must have
adequate strength to support both the projector and the mounting hanger. Before
Precautions
installation, check the combined weight of the projector and hanger, as well as the strength
of the ceiling based on that weight. If the strength is insufficient, provide adequate
reinforcement before proceeding.
Fastening plate (×2)
●Always mount on a level ceiling. Never install on an inclined ceiling.
(C)screw
●During installation, take appropriate measures to prevent lateral swaying due to
earthquakes or vibration (using wires, etc.).
Unit:mm
Phillips head machine screw
with integrated spring washer
and flat washer M4×10 (×8)
[Left/right angle]
The total weight of the mounting hanger itself is 4.5 kg.
(A)screw
(A)Screw …8 (B)Screw …4 (C)Screw …8 Fastening This M anual
plate…2
…1
Included
Accessories
10
120
200
230
4-φ10
Fastening
plate
(B)screw
Assembly and Installation
See Fig. 1
Detailed view of ceiling bracket and
projector bracket
Ceiling bracket mounting dimensions
1. Turn the projector over, and mount the projector bracket using the four (A) screws.
2. Determine the projection distance, and then determine the mounting position of the ceiling bracket.
3. Mount the ceiling bracket to the ceiling. See the figures for bracket mounting dimensions.
Unit:mm
Unit:mm
Fig. 2 …Adjustment (front view)
Fig. 3 …Adjustment (side view)
4. Hang the projector by aligning the groove in the projector bracket (attached to the projector) with the ceiling
bracket already fastened in place.
(E)screw (4 locations)
Left/right angle adjustment
Note) Be careful not to drop the projector. The projector is not yet securely mounted.
(A)screw
(4 locations)
(D)screw
(4 locations)
Vertical angle
adjustment
5. Mount the projector bracket and two fastening plates using the four (B) screws.
Inclination angle
adjustment
6. Tentatively fasten the four (A) screws to the ceiling bracket. (Tighten after determining the projection position.)
7. Mount the securing band to the projector bracket using the eight (C) screws.
ertical angle]
Adjusting the Projection Position
See Figs. 2, 3
1. Inclination angle adjustment :
After aligning the position with the screen, securely fasten the (A) screws in four locations.
［Inclination angle]
208
2. Vertical angle adjustment :
42.1
155.2
Loosen the (D) screws, align the position with the screen, and then securely fasten the (D) screws.
319
345.4
470.2
3. Left/right angle adjustment :
Loosen the (E) screws, align the position with the screen, and then securely fasten the (E) screws.
|