Contents
Getting Started and Basic Operation................................. 7
1
2 Using Flash........................................................................ 13
3 Wireless Flash ................................................................... 23
Reference ............................................................................ 30
Conventions Used in this Manual
The <9> symbol in the text refers to the +/– button.
9
The <8> symbol in the text refers to the Select/Set
8
button.
The operation procedures in this instruction manual assume that both
the camera and Speedlite’s power switches are ON.
Icons are used in the text to indicate the respective buttons, dials,
and settings. They match the same icons found on the camera and
Speedlite.
The (1) / (2) icons indicate that the respective function remains
in effect for 8 sec. or 12 sec.
Reference page numbers are indicated by (p.**).
This instruction manual uses the following alert symbols:
: The Caution symbol indicates a warning to prevent shooting
problems.
: The Note symbol gives supplemental information.
3
Nomenclature
Built-in wide panel
(retracted) (p.18)
Flash head
Wireless sensor
Bracket fitting
AF-assist beam emitter
(p.22)
Bracket mount
cover
Locking ring (p.9)
Mounting foot (p.9)
Locking pin (p.9)
Contacts
Case
Mini stand
Shoe
Mini stand pocket
4
Bounce angle index
<z>
Bounce lock release
button (p.17)
<E>
High-speed sync (FP flash)/
Shutter curtain
LCD panel
synchronization button (p.16)
* <A>
LCD panel illumination/
Custom Function
setting button (p.6/20)
Battery compartment cover
(p.8)
<G>
Zoom button/
<J>
Wireless set button
(p.18/27, 28)
Pilot lamp/Test firing/
Wireless slave auto power
off cancel button (p.10/25)
Power switch (p.10)
<L> : Power off
<K> : Power on
Flash exposure
confirmation lamp (p.11)
9
<
> +/– button
<D>
Flash mode/Slave setting button
(p.11, 19/29)
8
Wireless selector (p.9, 24)
<L> Wireless off (for on-camera flash)
<N> : Slave unit
* <
> Select/Set button
:
Asterisked buttons have a timer that keep the button’s function active for 8
sec. (1) after you let go of the button. The <B> illumination lasts for 12
sec.
5
LCD Panel
Zoom focal length
Aperture
Manual flash output level
Flash exposure compensation
amount
Max. flash range
Custom Function No.
Custom Function setting
<d> Manual zoom
<s> Auto zoom
<a/b>
for image size
E-TTL (ll)/TTL autoflash
<f>
Flash exposure
compensation
Indicator (meters)
Indicator (feet)
<c> High-speed
sync (FP flash)
Slave ID
<q> Manual flash
<x> Slave
<u> Custom Function
<w> Channel
<r> Second-curtain sync
Firing mode
Slave flash :X
To illuminate the LCD panel, press the <B> button.
The items actually displayed depend on the current settings.
6
Getting Started and
Basic Operation
Installing Batteries .................................................. 8
Attaching to the Camera......................................... 9
Turn on the Power Switch .................................... 10
Fully Automatic Flash Shooting............................. 11
Using E-TTL II and E-TTL Autoflash in the
Shooting Modes.................................................... 12
To avoid overheating and deteriorating the flash head, do not fire
rapid bursts of more than 20 continuous flashes. After 20
continuous flashes, allow a rest time of at least 10 min.
7
Installing Batteries
Install four size-AA batteries.
Open the cover.
Slide the battery compartment cover
1
2
3
as shown by the arrow and open it.
Install the batteries.
Make sure the + and – battery
contacts are correctly oriented as
shown in the battery compartment.
Close the cover.
Close the battery compartment cover
and slide it as shown by the arrow.
Recycling Time and Flash Count (with size-AA alkaline batteries)
Recycling Time (Approx.)
Flash Count (Approx.)
Normal Flash
0.1 - 3.7 sec.
200 - 1400
Based on new size-AA alkarine batteries and Canon’s testing standards.
Since the shape of their contacts is not standardized, using non-alkaline
size-AA batteries may result in faulty battery connection.
Use four new batteries of the same brand and type. Do not mix battery
types. When replacing batteries, replace all four batteries at the same time.
Size-AA Ni-MH or lithium batteries can also be used.
8
Attaching to the Camera
Loosen the locking ring.
Turn the locking ring as shown by the
1
2
3
arrow to loosen it.
Attach it to the camera.
Slip the Speedlite’s mounting foot all
the way into the hot shoe.
Tighten.
Turn the locking ring as shown by the
arrow. The locking pin will protrude
from the mounting foot to further
secure the attachment.
To detach the Speedlite, loosen the
locking ring until the locking pin
disengages. Then slip the Speedlite
out of the hot shoe.
Before attaching or detaching the Speedlite, be sure to turn off the Speedlite.
Wireless Selector Settings
The wireless selector is for switching
between normal flash shooting and
wireless flash shooting.
For normal flash shooting, be sure to set
the wireless selector to <L>.
9
Turn on the Power Switch
Set the power switch to <K>.
X The flash will start recycling.
1
Check that the flash is ready.
When the pilot lamp lights in red, the
flash is ready to fire.
2
To fire a test flash, press the pilot
lamp.
About Auto Power Off
To save battery power, the power will turn off automatically after 90 sec.
of idle use. To turn on the Speedlite again, press the shutter button
halfway. Or press the Speedlite’s test firing button.
A test firing cannot be fired while the camera’s operation timer 4 or 0
is active.
The Speedlite’s settings will be retained in memory even after the power
is turned off. To retain the Speedlite’s settings when you replace the
batteries, replace the batteries within 1 minute after turning off the power.
10
Fully Automatic Flash Shooting
When you set the camera’s shooting mode to <V> (Program AE) or
<U> (Full Auto), E-TTL II/E-TTL fully automatic flash will make it as
easy as normal AE shooting.
Set the Speedlite to <a>.
1
Press the <D> button so that
<a> is displayed.
Focus the subject.
2
Press the shutter button halfway to focus.
X The shutter speed and aperture will
be set as displayed in the viewfinder.
Check that the <Q> icon is lit in the
viewfinder.
Take the picture.
Take the picture.
3
X
A preflash is fired right before the shot
is taken, then the main flash is fired.
If a standard flash exposure was
X
obtained, the flash exposure confirmation
lamp will light for about 3 sec.
If the lens focal length blinks on the LCD panel, the periphery of the flash
picture may turn out dark. Use the built-in wide panel (p.18).
<a> will be displayed on the LCD panel even if the camera is
compatible with E-TTL II.
If the flash exposure confirmation lamp does not light, move closer to the
subject and take the picture again. With a digital camera, you can also
increase the camera’s ISO speed.
11
Using E-TTL II and E-TTL Autoflash in the Shooting Modes
Just set the camera’s shooting mode to <W> (aperture-priority AE),
<X> (shutter-priority AE), or <q> (manual) and you can use E-TTL
II/E-TTL autoflash.
Select this mode when you want to set the shutter speed manually.
The camera will then automatically set the aperture matching the shutter
speed to obtain a standard exposure.
X
If the aperture display blinks, it means that the background exposure will
be underexposed or overexposed. Adjust the shutter speed until the
aperture display stops blinking.
Select this mode when you want to set the aperture manually.
The camera will then automatically set the shutter speed matching the
aperture to obtain a standard exposure.
If the background is dark like a night scene, a slow sync speed will be used
to obtain a standard exposure of both the main subject and background.
Standard exposure of the main subject is obtained with the flash, while a
W
standard exposure of the background is obtained with a slow shutter speed.
Since a slow shutter speed will be used for low-light scenes, using a
tripod is recommended.
If the shutter speed display blinks, it means that the background
exposure will be underexposed or overexposed. Adjust the aperture until
the shutter speed display stops blinking.
Select this mode when you want to set both the shutter speed and aperture
manually.
q
Standard exposure of the main subject is obtained with the flash. The
exposure of the background is obtained with the shutter speed and aperture
combination you set.
If you use the <Z> or <Y> shooting mode, the result will be the same as
using the <V> (Program AE) mode.
Flash Sync Speeds and Apertures Used
Shutter Speed Setting
Automatic (1/60 sec. - 1/X sec.)
Manual (30 sec. - 1/X sec.)
Aperture Setting
Automatic
Automatic
Manual
V
X
W
q
Automatic (30 sec. - 1/X sec.)
Manual (buLb, 30 sec. - 1/X sec.)
Manual
1/X sec. is the camera’s maximum flash sync speed.
12
Using Flash
fFlash Exposure Compensation ....................... 14
7 FE Lock ........................................................ 15
cHigh-Speed Sync ............................................. 16
rSecond-Curtain Sync..................................... 16
Bounce Flash........................................................ 17
H Setting the Flash Coverage and Using
the Wide Panel ..................................................... 18
q Manual Flash .................................................. 19
C Setting Custom Functions........................... 20
Custom Function Settings .................................... 21
About Color Temperature Information Transmission.. 22
Reverting to 430EX Default Settings.................... 22
About the AF-Assist Beam ................................... 22
13
fFlash Exposure Compensation
You can adjust the flash output as easily as normal exposure
compensation. Flash exposure compensation can be set up to ±3 stops
in 1/3-stop increments. (If the camera’s exposure compensation is set in
1/2-stop increments, flash exposure compensation is set in 1/2-stop
increments.)
Press the <8> button until the
1
<f> icon and compensation
amount start blinking.
Set the flash exposure
2 compensation amount.
Press the <9> button to set the
amount.
To cancel the flash exposure
compensation, set the amount to +0.
Press the <8> button.
3
X The flash exposure compensation
amount will be set.
If flash exposure compensation has been set with both the Speedlite and
camera, the Speedlite’s flash exposure compensation amount will override
the camera’s.
Using <9>
This is for setting various numeric settings. Pressing the <6> (plus)
button increases the number, while the <5> (minus) button decreases
the number.
14
7 FE Lock
FE (flash exposure) lock enables you to lock the correct flash exposure
for any part of the picture.
With <a> displayed on the LCD panel, you press the camera’s
<7> button. If the camera does not have the <7> button, press
the <P> button.
Focus the subject.
1
Press the <7> button. (3)
2
Aim the viewfinder center over the
subject and press the <7> button.
X A preflash will be fired to obtain a
flash exposure reading for the
subject.
X “FEL” will be displyed on the LCD
panel for 0.5 sec.
Each time you press the <7>
button, a preflash will be fired and a
new flash exposure reading will be
locked.
If the subject is too far away and underexposure will result, the <Q> icon
will blink in the viewfinder. Move closer to the subject and try the FE lock
again.
If <a> is not displayed on the LCD panel, FE lock will not be
possible.
If the subject is too small, FE lock might not be very effective.
15
cHigh-Speed Sync
With high-speed sync, you can use flash with all shutter speeds. This is
convenient when you want to use aperture priority for fill-flash portraits.
Press the <E> button so that
<c> is displayed.
Check that the <F> icon is lit in the
viewfinder.
If you set a shutter speed that is the same or slower than the camera’s
maximum flash sync speed, <F> wil not be displayed in the viewfinder.
With high-speed sync, the faster the shutter speed, the shorter the
effective flash range will be. Check the LCD panel for the maximum flash
range for the respective shutter speed.
To return to normal flash, press the <E> button so that <c> icon
turns off.
rSecond-Curtain Sync
With a slow shutter speed, you can create a light trail following the
subject. The flash fires right before the shutter closes.
Press the <E> button so that
<r> is displayed.
Setting the shooting mode to “buLb” will make it easier for second-
curtain sync.
To return to normal flash, press the <E> button so that the <r>
icon turns off.
With E-TTL ll/E-TTL, the flash will fire twice even with a slow sync speed.
The first flash is the preflash.
16
Bounce Flash
By pointing the flash head toward a wall or ceiling, the flash will bounce
off the surface before illuminating the subject. This can soften shadows
behind the subject for a more natural-looking shot. This is called bounce
flash.
Set the Bounce Direction
Hold down the <z> button and turn the flash head.
If the flash coverage is set automatically, the flash coverage will be set
to 50mm.
The LCD panel will also display <O> mm. (p.18)
You can also set the flash coverage manually.
If the wall or ceiling is too far away, the bounced flash might be too weak
and result in underexposure.
The wall or ceiling should be a plain, white color for high reflectance. If
the bounce surface is not white, a color cast may result in the picture.
After you take the shot, if the flash exposure confirmation lamp does not
light, use a larger aperture opening and try again. With a digital camera,
you can also increase the ISO speed.
17
H
Setting the Flash Coverage and Using the Wide Panel
The flash coverage can be set to match the lens focal length from
24mm to 105mm. The flash coverage can be set automatically or
manually. Also, with the built-in wide panel, the flash coverage will be
compatible with ultra wide-angle lenses as short as 14mm.
Press the <G> button.
Press the <9> button to change the
flash coverage.
When the flash coverage is set
automatically, <d> is not displayed.
If you set the flash coverage manually, make sure it covers the lens focal
length so that the picture will not have a dark periphery.
Using the Wide Panel
Pull out the wide panel and place it over
the flash head as shown.
The <G> button will not
work.
The flash coverage will not be compatible with the EF15mm f/2.8
Fisheye lens.
For the effective lens focal length (or crop factor), refer to the camera’s
instruction manual.
If you use bounce flash with the wide panel in place, the entire display on
the LCD panel will blink as a warning. Since the subject will be
illuminated by both the bounce flash and direct flash, it will look
unnatural.
Pull out the wide panel gently. Using excessive force may detach the
wide panel.
18
q Manual Flash
You can set the flash output from 1/64 power to 1/1 full power in full-
stop increments.
Use a hand-held flash meter to determine the required flash output to
obtain a correct flash exposure. Be sure to first set the camera’s
shooting mode to <W> or <q>.
Press the <D> button so
that <q> is displayed.
1
Set the flash output.
2
Press the <8> button.
X The flash output display will blink.
Press the <9> button to set the
flash output, then press the <8>
button.
Press the shutter button halfway to
see the effective flash range
displayed.
19
C Setting Custom Functions
You can customize Speedlite features to suit your preferences. Do it
with Custom Functions.
Press the <A> button for 2
1
sec. so that <u> is displayed.
Select the Custom Function No.
2
Press the <9> button to select the
Custom Function number.
Change the setting.
3
Press the <8> button.
X The Custom Function number and
setting number will blink.
X Press the <9> button to select “0”
or “1”, then press the <8> button.
X After you set the Custom Function
and press the <D> button, the
camera will be ready to shoot.
Changing Meters or Feet
After step 1 above, press the <8> button for at least 2 sec. When the
distance display blinks, press the <9> button to switch between meters
and feet. Then press the <8> button.
20
Custom Function Settings
Custom
Setting
Function
No.
Item
Setting Description
No.
0
1
0
1
0
1
0
1
0
1
ON
C.Fn-01 Auto Power Off activation
OFF
Auto power off after 60 min.
Auto power off after 10 min.
Enabled
Slave unit’s auto power off
C.Fn-02
time
C.Fn-03 Auto zoom for image size
C.Fn-04 AF-assist beam OFF
C.Fn-05 Modeling flash
Disabled
Disabled
Enabled
Enabled
Disabled
Display maximum flash range. (Displays up
to max. 18 m/60 ft)
LCD panel display when
C.Fn-06 shutter button pressed
halfway
0
1
Display aperture.
C.Fn-05-1:Convenient when you want to check the depth of field. (p.28)
C.Fn-06 can be set only with Type-A cameras.
If “AF-assist beam OFF” is set with the Speedlite or camera, the AF-
assist beam will not be emitted.
Automatic Setting of Flash Coverage for the Camera’s Image Size
EOS digital cameras have one of three image sizes. The lens’ effective
focal length will differ depending on the camera’s image size. The
Speedlite automatically recognizes the EOS digital camera’s image size
and automatically sets the flash coverage for lens focal lengths from
24mm to 105mm.
When the Speedlite is attached to a compatible camera, <s> will
appear on the Speedlite’s LCD panel.
21
About Color Temperature Information Transmission
When the flash fires, the color temperature information is transmitted to
certain specific EOS digital camera. This feature optimizes the flash
picture’s white balance. When the camera’s color balance is set to
<A> or <Q>, it will work automatically.
To see if this feature works with your camera, see the “White Balance”
specification in the “Specifications” of your camera’s instruction manual.
Reverting to 430EX Default Settings
When 430EX is attached to an EOS camera equipped with a <B>
button, you can press it to revert the 430EX’s settings (except Custom
Functions) to the default.
About the AF-Assist Beam
Under low-light or low-contrast conditions, the built-in AF-assist beam
will be emitted automatically to make it eaasier to autofocus. The
430EX’s AF-assist beam is compatible with the AF points of almost all
EOS cameras. The AF-assist beam is compatible with 28mm and
longer lenses. The effective range is shown below.
Position
Center
Effective Range (m / ft)
Approx. 0.7 - 10 / 2.3 - 32.8
Approx. 0.7 - 5 / 2.3 - 16.4
Periphery
22
Wireless Flash
Wireless Flash...................................................... 24
Setting Manual Flash with the Slave Unit............. 29
23
Wireless Flash
With multiple Canon Speedlites having the wireless flash feature, you can
create various lighting effects with the same ease as using normal E-TTL II
autoflash.
The settings you input with the master unit attached to the camera are also
transmitted to the slave unit(s) controlled by wireless. Therefore, you need
not operate the slave unit(s) at all during the shoot.
For details on wireless flash photography and operating the master unit,
see the master unit’s instruction manual. The procedure below applies to a
master unit attached to the camera and slave unit(s) controlled by wireless.
Set the master unit.
Attach Speedlite 580EX, 550EX, ST-
1
E2, MR-14EX or MT-24EX to the
camera and set it as necessary.
Set the 430EX as the slave unit.
Set the wireless selector to
2
<N>.
Check the communication
3 channel.
If the master unit and slave unit(s) are
set to a different channel, set them all
to the same channel (p.27).
Set the slave ID.
Set the slave ID when using two (A
4
and B) or three (A, B, and C) slave
groups (p.28).
Position the camera and
5 Speedlites as desired.
Position the slave unit(s) within the
master unit's wireless transmission
range.
24
Set the master unit’s flash mode
6 to <a>.
The slave unit(s) will also be
automatically set to <a>.
Check that the flash is ready.
7
When the slave unit is ready to fire,
the AF-assist beam will blink once
each second.
Check the flash operation.
8
Press the master unit’s test firing
button.
X The slave unit will fire. If the flash
does not fire, adjust the slave unit’s
angle toward the master unit and
distance from the master unit.
Set the camera and shoot.
9
Set the camera in the same way as
with normal flash shooting.
Sample wireless flash setup
Indoors
Outdoors
Slave A
Slave B
80°
Master
unit
8m (26.2ft.) 12m (39.4ft.)
25
Use the mini stand (tripod socket provided) to prop up the slave unit.
Use the bounce feature to swing the slave unit’s flash body so that
the wireless sensor faces the master unit.
Indoors, the wireless signal may also bounce off the wall so there is
more leeway in positioning the slave unit(s).
After positioning the slave unit(s), be sure to test the wireless
operation before shooting.
Do not place any obstacles between the master unit and slave
unit(s). Obstacles can block the transmission of wireless signals.
Even with multiple slave units, all of them will be controlled in the same
way via wireless.
The Speedlite’s zoom setting will be set automatically to 24mm. It is
possible to change the master unit’s zoom setting. However, note that
the master unit transmits wireless signals to the slave unit(s) with the
preflash. Therefore, the flash coverage must cover the slave unit’s
position. If you change the master unit’s zoom setting, be sure to test the
wireless operation before shooting.
If the slave unit enters auto power off, it can be turned on again by
pressing the master unit’s test firing button.
If the 430EX is set as a slave unit and remains in auto power off mode for
more than 8 hours, it will not turn on even if you try to fire a test flash with
the master unit. In this case, press the slave unit’s test firing button to
turn it on.
A test flash cannot be fired while the camera’s operation timer 4 or 0
is active.
26
Using Fully Automatic Wireless Flash
Flash exposure compensation and other settings set with the master
unit will also be automatically set in the slave units. Thus, you need not
make settings on the slave unit(s). Wireless flash with the following
settings can be done in the same way as with normal flash shooting.
• Flash exposure compensation
• High-speed sync (FP flash)
• FE lock
• FEB
• Manual flash
• Stroboscopic flash
With FE lock, if even one Speedlite will result in underexposure, the <Q>
icon will blink in the viewfinder. Open the aperture more or move the
slave unit closer to the subject.
With a wireless flash system, the master unit’s settings will not be
displayed on the 430EX’s LCD panel.
Setting Communication Channel
If there is another Canon wireless flash system nearby, you can change
the channel No. to prevent signal confusion. Both the master and slave
units must be set to the same channel No.
Press the <G> button
so that <w> blinks.
1
Set the channel No.
2
Press the <9> button to select the
number, then press the <8> button.
27
Setting the Slave ID
Set the slave ID if you use two (A and B) or three (A, B, and C) slave
groups.
Press the <G> button
so that <x> blinks.
1
Press the <9> button to select
2 the slave ID (A, B, or C).
Press the <8> button to set the
3 slave ID.
Modeling Flash
If the camera has a depth-of-field preview button, press it to fire a 1-sec.
burst of flashes. This is the modeling flash.
You can check the lighting and shadow effects. You can fire the
modeling flash for both wireless and normal flash shooting.
Do not fire the modeling flash more than 10 consecutive times. If you fire the
modeling flash 10 consecutive times, allow the Speedlite to rest for at least
10 min. to avoid overheating and deteriorating the flash head.
The modeling flash cannot be fired with the EOS 300/REBEL 2000 and
Type-B cameras (p.2).
About Slave Group Control
For example, if you have the slave ID set
to <1> for three Speedlites, all three
Speedlites will be controlled as if they
were one Speedlite in slave group A.
Slave group A
ID = A
ID = A
ID = A
28
Setting Manual Flash with the Slave Unit
Manual flash can be set manually with the slave unit. Do this in the
following cases:
(1) When you want to set the flash output with the slave units
individually for wireless or manual flash, as with studio flash units.
(2) When you use Speedlite Transmitter ST-E2 for wireless or manual
flash.
Press the <D> button for 2 sec.
X <q> will blink.
Set the manual flash output (p.19).
29
Reference
430EX System
3
4
1
2
7
5
6
8
1 Speedlite 430EX (Slave unit)
2 Mini stand (included with 430EX)
3 Speedlite 580EX (On-camera/Master unit)
4 Speedlite Transmitter ST-E2
Dedicated transmitter for wireless control of 430EX set as slave units.
5 Macro Ring Lite MR-14EX / 6 Macro Twin Lite MT-24EX
Flash for macro photography. Compatible with wireless flash and it can be
used together with the 430EX slave unit.
7 Off-Camera Shoe Cord 2
Enables the 430EX to be connected to the camera up to 60 cm/2 ft away. All of
the EOS camera’s automatic functions can be used.
8 Speedlite Bracket SB-E1
The SB-E1 is not available in all countries.
30
Troubleshooting
Have a problem? See the table below.
The Speedlite does not detach from the camera.
The mounting foot’s locking pin has not been retracted.
X Loosen the locking ring all the way before detaching the Speedlite.
(p.9)
The Speedlite does not fire.
The batteries are installed in the wrong orientation.
X Install the batteries in the correct orientation. (p.8)
The Speedlite’s internal batteries are exhausted.
X If the flash recycling time is 30 sec. or longer, replace the
batteries. (p.8)
Attach the Speedlite securely to the camera.
X Attach the Speedlite’s mounting foot securely to the camera. (p.9)
The electrical contacts of the Speedlite and camera are dirty.
X Clean the contacts. (p.9)
The slave unit does not fire.
The slave’s wireless selector is not set to <N>.
X Set it to <N>. (p.24)
The slave unit is not positioned properly.
X Place the slave unit within the master unit’s transmission range.
(p.26)
X Point the slave unit’s sensor toward the master unit. (p.26)
The power turns off by itself.
After 90 sec. of idle operation, auto power off took effect.
X Press the shutter button halfway or press the test firing button.
(p.10)
The entire LCD panel blinks.
The wide panel has been pulled out for bounce flash.
X Retract the wide panel. (p.18)
31
The periphery or bottom of the picture looks dark.
When you set the flash coverage manually, the setting was a
higher number than the lens focal length, resulting in a dark
periphery.
X Set the flash coverage that is a lower number than the lens focal
length or set it to auto zoom. (p.18)
If only the bottom of the picture looks dark, you were too
close to the subject.
X Keep at least 0.7 m/2.3 ft away from the subject.
The flash exposure is underexposed or overexposed.
There was a highly reflective object (glass window, etc.) in
the picture.
X Use FE lock. (p.15)
The subject has a very dark or light color.
X Set flash exposure compensation. For a dark subject, set a
decreased flash exposure. And for a bright subject, set an
increased flash exposure. (p.14)
You used high-speed sync.
X With high-speed sync, the effective flash range will be shorter.
Make sure the subject is within the effective flash range displayed.
(p.16)
The picture is really blurred.
The shooting mode was set to <W>, and the scene was
dark.
X Use a tripod or set the shooting mode to <V>. (p.12)
32
Specifications
• Type
Type:
On-camera, E-TTL II/E-TTL/TTL autoflash Speedlite
Compatible cameras:
Type-A EOS cameras (E-TTL II/E-TTL autoflash),
Type-B EOS cameras (TTL autoflash)
43/141 (at 105mm focal length, ISO 100 in meters/feet)
24 - 105mm (14mm with wide panel)
• Auto zoom (flash coverage set automatically for lens focal
length and image size)
Guide No.:
Flash coverage:
• Manual zoom
• Flash head swing (bounce flash)
Flash duration:
Normal flash: 1.2 ms or shorter
Color temperature
information transmission: Flash color temperature information transmitted to camera
• Exposure Control
Exposure Control Type: E-TTL II/E-TTL/TTL autoflash, manual flash
Flash range
(
with EF50mm f/1.4, ISO 100
)
: Normal flash: Approx. 0.7 - 24.3 m / 2.3 - 79.7 ft
High-speed sync: Approx. 0.7 - 12 m / 2.3 - 39.4 ft (at 1/250
sec.)
Flash exposure
compensation:
FE lock:
Manual, ±3 stops in 1/3- or 1/2-stop increments
With <7> button or <P> button
Provided
High-speed sync:
Flash exposure
confirmation:
Flash exposure confirmation lamp lights
• Flash Recycling (with size-AA alkaline batteries)
Recycling time/
Flash-ready indicator:
Normal flash: 3.7 sec. / Red pilot lamp lights
• Wireless Flash
Transmission method:
Channels:
Optical pulse
4
Wireless options:
Transmission range
(Approx.):
OFF and Slave
Reception angle: ±40° horizontal, ±30° vertical
AF-assist beam blinks
Slave-ready indicator:
Modeling flash:
Fired with camera’s depth-of-field preview button
• Custom Functions: 6 (12 settings)
33
• AF-Assist Beam
Linkable AF points:
1 - 9 AF points (28mm or longer focal length)
Effective range (Approx.): At center: 0.7 - 10 m / 2.3 - 32.8 ft,
Periphery: 0.7 - 5 m / 2.3 - 16.4 ft
• Power Source
Internal power:
Four size-AA alkaline
* Size-AA Ni-MH or lithium batteries also possible
Battery life
(Approx. flash count):
Power saving:
200 - 1400 flashes (with size-AA alkaline batteries)
Power off after 90 sec. or idle operation (60 min. if set as
slave)
• Dimensions
(W x H x D):
72 x 122 x 101 mm / 2.8 x 4.8 x 4.0 in
• Weight:
330 g / 11.6 oz (Speedlite only, excluding batteries)
All specifications are based on Canon’s testing criteria.
Product specifications and external appearance are subject to change without
notice.
Manual Flash Guide No. (GNo.) (ISO 100, in meters/feet)
Flash Coverage (mm)
Flash Output
14
24
28
35
50
70
80
105
43/
11/
25/
82
27/
31/
34/
37/
40/
1/1
1/2
36.1
88.6 101.7 111.5 121.4 131.2 141.1
7.8/
25.6
17.7/ 19.1/ 21.9/
58.1 62.7 71.9
24/
78.7
26.2/ 28.3/ 30.4/
86
92.8
99.7
5.5/
18
12.5/ 13.5/ 15.5/
17/
55.8
18.5/
60.7
20/
65.6
21.5/
70.5
1/4
41
44.3
50.9
3.9/
12.8
8.8/
28.9
9.5/
31.2
11/
36.1
12/
39.4
13.1/ 14.1/ 15.2/
1/8
43
46.3
49.9
2.8/
9.2
6.3/
20.7
6.8/
22.3
7.8/
25.6
8.5/
27.9
9.3/
30.5
10/
32.8
10.8/
35.4
1/16
1/32
1/64
1.9/
6.2
4.4/
14.4
4.8/
15.7
5.5/
18
6/
19.7
6.5/
21.3
7.1/
23.3
7.6/
24.9
1.4/
4.6
3.1/
10.2
3.4/
11.2
3.9/
12.8
4.3/
14.1
4.6/
15.1
5/
16.4
5.4/
17.7
34
Using a Type-B Camera
If you use the 430EX with a Type-B camera (TTL autoflash camera),
note the available features and restrictions below.
When a Type-B camera is used with the 430EX set to autoflash,
<b> will be displayed on the Speedlite’s LCD panel.
Features Available with All Type-B Cameras
Configuration
Available Features
TTL autoflash
Flash exposure compensation
Manual flash
On-camera
shooting
Second-curtain sync
Manual flash
Wireless flash
Stroboscopic flash
Features not Available with Any Type-B Cameras
E-TTL II/E-TTL autoflash
FE lock
High-speed sync (FP flash)
Autoflash with wireless flash
Flash ratio set with multi-Speedlite wireless flash
Features not Available with Some Type-B Cameras
EOS 750/850: Stroboscopic flash, second-curtain sync,
wireless flash
35
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Do not make any changes or modifications to the equipment unless otherwise
specified in the instructions. If such changes or modifications should be made,
you could be required to stop operation of the equipment.
This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
36
This mark indicates that the product complies with Australia’s EMC
regulations.
37
This Instructions booklet is dated July 2005. For information on the camera’s
compatibility with system accessories marketed after this date, contact your
nearest Canon Service Center.
|