Rearview Mirror with 4.5" Color LCD with
Navigation and 2 Camera inputs
Model: LCMR5RP
Installation Manual
Features:
• Rearview Mirror with 4.5" LCD
• Rearview Camera Input
• Interior Camera Input
• Navigation Input
• NTSC /PAL Camera Compatible
TABLE OF CONTENTS
Cautions!
Preface
1
3
WARNING
Packing list
3
3
1.Installation Instructions
2.Signal Inputs
4
5
3.Controls and Indicators
7
Specifications
9
Maintenance
10
11
12
Troubleshooting
Illustration of connections
2
Preface
This replacement mirror /monitor can display up to 3 different video
inputs. The inputs are Navigation, Rear observation camera and Interior
observation camera.
Not all rearview mirrors attach to the vehicle with the same style mount.
Please consult the application guide for the appropriate mounting bracket
for your vehicle or call Tech Service at 800-225-6074.
There is a blind spot that exists at the back of a vehicle while the vehicle is
in reverse. Equipped with a camera, this electronic rearview mirror
ensures safety by providing the driver with a clear and wide image of the
area behind the vehicle while it is in reverse.
WARNING:
Backing up vehicle
Do not back up the vehicle while watching the mirror/monitor screen.
Always look in the direction of vehicle motion. Use the mirror/monitor as
an aid in safety confirmation. The distance looks different in the monitor.
Packing list
The Rear view mirror Model LCMR5RP consists of the following items:
1. Rear View Mirror-1
2. Camera Cable-2
3. Control Box-1
4. Control Box Monitor Cable -1
3
1. Installation Instructions
(1) Mount the mirror/monitor
a)
b)
Remove the original factory mirror. (Do not use excessive force when
removing factory mirror.) Check to make sure that the factory mirror mount you
remove matches the mirror mount on the replacement mirror. If it does not
match, consult the application guide or call Technical Service at 800-225-6074.
Slide the receiving bracket on the back of the new mirror stalk onto the
windshield mounting button. Move the bracket back and forth until completely
seated.
c) Tightly the T-20 mounting bracket screw.
(2) Navigation monitor connection: Insert the connector from the navigation
monitor cable into the receptacle at the backside of the mirror/monitor. Route the rest
of the monitor cable under the headliner, down the A pillar to the Navigation
computer.
(3) Control box connection: Connect the 8-pin extension cable to the rearview
mirror/monitor 8 pin cable. Route the cable under the headliner of the windshield then
down the A pillar behind the plastic shroud to the under dash area. Connect the 8-pin
cable to the control box 8 pin connector.
4
(4) Electrical Connections: Connect the 4 wires in the following manner.
a) Red wire - 12 volt constant (positive)
b) Black wire - Chassis ground (negative)
c) Blue wire - 12-volt ignition (12 volt with ignition on)
d) Green wire - Reverse light switch (12 volt when vehicle is in the reverse gear)
WARNING: Observe polarity when connecting the wires.
Figure 2
2. Signal Inputs
The signal input connections for the system include:
(1)
Rear Camera: Plug the RJ 11 camera cable end into the control box
AVin-1 location, route the cable to the rear camera and plug the 4-pin connector
into camera 4 pin connector. Users can see the rearview camera image when the car
is shifted into reverse.
(2) Interior Camera: Plug the RJ 11 camera cable end into the control box AVin-2,
Users can see the interior camera image when the “CAM” button is pressed.
(3)
Navigation: The navigation signal is supplied via the monitor cable
plugged directly into the rear of the mirror.
(4) Navigation Image (optional Navigation System required)
The Navigation Image is the default mode, and will only be overridden
when the vehicle gear selector is moved into reverse, or if the CAM button
on the mirror is pressed.
5
Some operators may find that leaving the Navigation Image on the LCD
monitor at all times becomes a distraction while operating their motor
vehicle. For the convenience of those operators, a ‘Display Timer Slide
Control Switch’ has been added to the mirror.
A. When the Slide Control Switch is moved to the far right end position,
the Navigation image will remain on at all times.
B. When the Slide Control Switch is moved to the far left end position,
the Navigation image will remain off at all times.
C. Positioning the Slide Control Switch anywhere in the center area will
automatically enable an internal timer. The timer is adjustable between 10
Seconds (further left) to 3 minutes (further right).
D. When the Navigation System is in guidance mode, every time a turn-
by-turn voice guidance command is received, the Navigation image will
automatically turn on and remain on for the pre-selected time set by the
Slide Switch. After the pre-set time has expired, the Navigation display will
turn off and remain off until the next voice command is received.
HINT 1: When entering a new address into the Navigation Address Book, it
will be easier to move the Slide Control Switch all the way to the right to
keep the LCD display on until the address has been completed.
HINT 2: When in Timed Display Mode, you can press the “+” or “-“ button on
the mirror to turn the Navigation image on for the full extent of the pre-set
time.
6
Figure 5
3. Controls and Indicators
Figure 5 shows the function controls of the rear view mirror.
A: 4.5" LCD Panel
B: Rearview Mirror Glass
C: “+”Button (optional Navigation System required)
Incrementally increase volume level of the navigation voice command when pressed.
Note: Will only operate when the Navigation System remote control is removed from the
cradle.
D: “CAM”Button
- If you have installed an optional interior view camera, pressing the CAM button will
display the image from the interior view camera on the LCD panel. - If you do not have an
interior view camera installed, but have installed a back up camera, then pressing the CAM
button will display the image from the back up camera on the LCD panel.
- Either image will be displayed for as long as the CAM button is held on. As soon as the
button is released, the LCD will automatically switch back to the original setting.
E: “MAP”Button (optional Navigation System required)
Each time the “MAP” button is pressed, the navigation display will toggle between Map,
Icon only and split screen while in navigation mode.
7
Note: Will only operate when the Navigation System remote control is removed from the
cradle.
F: “-” Button (optional Navigation System required)
Incrementally decrease volume level of the navigation voice command when pressed.
Note: Will only operate when the Navigation System remote control is removed from the
cradle.
G: Internal Speaker
H: LCD Brightness Control
I: Internal Infra-RED Receiver for use with Navigation System Remote Control.
J: Power LED (Red when Power is on)
K: Display Timer Slide Control Switch : (optional Navigation System required)
Refer to page 5 Signal Inputs #4 for detailed operation notes.
M: Internal Speaker Switch: Used to turn mirror speaker on/off. Move this switch to the
Off position when using the external speaker interface included with the optional
Navigation System.
8
Specifications
General
Power Supply
12VDC
<12W
Power Consumption
Current Draw
<800mA
Video Input
1Vp-p/ 75 Impedance
Audio Input
<=1V
Audio Power Output
Operating Temperature Range
0.5W × 1 (16Ω)
0℃ to 50℃
Display System
Screen
4.5” TFT Color LCD
400 cd/㎡
Brightness
Contrast Ratio
Backlight Life
Resolution
150 : 1
10000 hours
960×234
Video Format
Display Format
Navigation input
PAL/NTSC auto detect
16 : 9
RGB
9
Maintenance
Though your Rearview mirror requires little care, you can still maintain its
condition and performance by following the procedures below.
•
Keep your system away from excessive moisture, extreme heat or cold,
and magnetic fields.
•
•
Keep liquids away from the display and mirror.
To avoid damage, do not place external devices or other objects on the
top of the mirror.
•
•
Occasionally wipe the rearview mirror set with a soft, damp cloth.
Occasionally clean the surface of the mirror with a soft cloth moistened
with water or window cleaner.
10
Troubleshooting
Symptoms
Solutions
1. Check the installation-wiring diagram.
2. Ensure that the parallel red and black line from
the control box is connected properly.
3. Check for 12 volts on the blue wire while the
ignition on.
The ON/OFF signal light <E> is
not on after the car is started?
1. Check the rearview Camera lens.
2. Check the rearview Camera wiring and
connection.
3. Check the cable from the rearview mirror is
connected to the control box.
No video signal appears while
reversing the car?
4. Check out the wire connection (to find out
whether the system’s reverse wire cable is
connected to the reverse switch gear of the car)
Video image is not sharp enough?
Clean the lens of the camera.
Illustration of Connections
Figure 6
12
© 2005 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788
128-7381
|