Cabletron Systems Switch 7F06 02 User Manual

7F06-02 FDDI SmartSWITCH^™

Interface Module

User’s Guide

9031672-01

Notice

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

NOTE: This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15 of the

FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is

operated in a commercial environment. This equipment uses,

generates, and can radiate radio frequency energy and if not

installed in accordance with the operator’s manual, may cause

harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause interference in

which case the user will be required to correct the interference at his

own expense.

WARNING: Changes or modiﬁcations made to this device which

are not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

DOC NOTICE

This digital apparatus does not exceed the Class A limits for radio

noise emissions from digital apparatus set out in the Radio

Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits

radioélectriques dépassant les limites applicables aux appareils

numériques de la class A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des

Communications du Canada.

Notice

VCCI NOTICE

This equipment is in the 1st Class Category (information

equipment to be used in commercial and/or industrial areas) and

conforms to the standards set by the Voluntary Control Council for

Interference by Information Technology Equipment (VCCI) aimed

at preventing radio interference in commercial and/or industrial

areas.

Consequently, when used in a residential area or in an adjacent area

thereto, radio interference may be caused to radios and TV

receivers, etc.

Read the instructions for correct handling.

iii

CONTENTS

CHAPTER 1 INTRODUCTION

1.1 USING THIS MANUAL .........................................................................1-1

1.2 THE 7F06-02 MODULE...........................................................................1-2

1.2.1 Cable Type and FPIMs ..................................................................1-2

1.2.2 7C03 MMAC SmartSwitch, the 7C04 Workgroup SmartSwitch

and the 7C04-R Workgroup SmartSwitch ..................................1-3

1.3 FEATURES ................................................................................................1-4

1.3.1 FPIMs...............................................................................................1-4

1.3.2 LANVIEW LEDs............................................................................1-4

1.3.3 Connectivity....................................................................................1-4

1.4 RELATED MANUALS ............................................................................1-5

1.5 GETTING HELP.......................................................................................1-5

CHAPTER 2 NETWORK REQUIREMENTS

2.1 FPIM MODULE SPECIFICATIONS......................................................2-1

2.1.1 FPIM-00 and FPIM-01 ...................................................................2-1

2.1.2 FPIM-02 and FPIM-04 ...................................................................2-3

2.1.3 FPIM-05 and FPIM-07 ...................................................................2-4

CHAPTER 3 INSTALLATION/REMOVAL

3.1 UNPACKING THE 7F06-2 MODULE...................................................3-1

3.2 INSTALLING FPIMS...............................................................................3-1

3.3 INSTALLING/REMOVING THE 7F06-02 MODULE.......................3-2

3.3.1 Installing in the 7C03 SmartSwitch .............................................3-2

3.3.2 Removing from the7C03 SmartSwitch........................................3-3

3.3.3 Installing in the 7C04 or 7C04-R Workgroup SmartSwitch .....3-5

3.3.4 Removing from the 7C04 or 7C04-R Workgroup SmartSwitch.3-

CHAPTER 4 TROUBLESHOOTING

CHAPTER 5 TECHNICAL SPECIFICATIONS

5.1 STANDARDS............................................................................................5-1

5.2 EMI.............................................................................................................5-1

5.3 EMC ...........................................................................................................5-1

5.4 NETWORK INTERFACES......................................................................5-1

5.5 SAFETY......................................................................................................5-2

5.6 SERVICE....................................................................................................5-2

Contents

5.7 PHYSICAL ................................................................................................5-2

5.7.1 Dimensions .....................................................................................5-2

5.7.2 Weight..............................................................................................5-2

CHAPTER 1

INTRODUCTION

Welcome to Cabletron Systems 7F06-02 FDDI SmartSwitch Interface

Module User’s Guide. This guide is a simple reference for installing

and using the 7F06-02 Module. Before installing this module, you

should carefully read through this manual to gain a full

understanding of its capabilities.

The 7F06-02 Module is a two port FDDI module. This module

connects to a network and the 7X00 SmartSwitch™ Control

Module in the 7C03,7C04 or 7C04-R MMAC SmartSwitch via a

SmartSwitch bus.

1.1 USING THIS MANUAL

Chapter 1, Introduction, discusses the capabilities and special

features of Cabletron Systems 7F06-02 Module. This chapter also

includes a list of related manuals.

Chapter 2, Network Requirements, contains a list of available

FPIMs and the network requirements that should be considered

before installing the 7F06-02 Module.

Chapter 3, Installation/Removal, contains instructions for

installing and removing the 7F06-02 in the 7C03 MMAC

SmartSwitch, the 7C04 Workgroup SmartSwitch or the 7C04-R

Workgroup SmartSwitch.

Chapter 4, Troubleshooting, contains instructions for using

LANVIEW^®(Cabletron Systems built-in diagnostic and status

monitoring system).

Chapter 5, Technical Speciﬁcations, provides detailed information

about the physical characteristics of the 7F06-02 Module.

1-1

INTRODUCTION

1.2 THE 7F06-02 MODULE

The 7F06-02 Module provides two Fiber Optic ports via front panel

FPIM modules.

1.2.1 Cable Type and FPIMs

The 7F06-02 module has two front panel connectors that interface

to the 7X00 Smart Switch Module through the chassis backplane.

The front panel connections are standard Cabletron FPIMs. There

are two FPIMs for each channel. These FPIMs allow the use of

single mode or multimode ﬁber cable with MIC or SC type

connectors and twisted pair cable, either shielded or unshielded.

1-2

INTRODUCTION

7F06-02

Figure 1-1. 7F06-02 Module

1.2.2 7C03 MMAC SmartSwitch, the 7C04 Workgroup

SmartSwitch and the 7C04-R Workgroup

SmartSwitch

The 7F06-02 Module is designed to be installed in the 7C03 MMAC

SmartSwitch, the 7C04 Workgroup SmartSwitch or the 7C04-R

Workgroup SmartSwitch.

The modular design of the 7C03 MMAC SmartSwitch allows other

modules that support Ethernet, Fast Ethernet, ATM, FDDI, or

1-3

INTRODUCTION

Token Ring to be used with the 7F06-02 Module. These modules

provide the capability to share data without the use of external

bridges or routers.

The 7C03 MMAC SmartSwitch is a unique module that can be

installed in an MMAC Series chassis. The 7C04 Workgroup

SmartSwitch and the 7C04-R Workgroup SmartSwitch are stand-

alone chassis that provide the same functions.

1.3 FEATURES

The 7F06-02 Module provides two FDDI ports via front panel

FPIMs. The 7F06-02 Module includes the following features:

1.3.1 FPIMs

The front panel connections are standard Cabletron FPIMs. These

FPIMs allow the use of single mode or multimode ﬁber cable with

MIC or SC type connectors.

1.3.2 LANVIEW LEDs

The 7F06-02 uses LANVIEW, Cabletron Systems built-in visual

diagnostic and status monitoring system. With LANVIEW LEDs,

you can quickly identify, at a glance, the status of the device

connected to a port on the 7F06-02 Module.

1.3.3 Connectivity

The 7F06-02 Module has one backplane connection and two sets of

A/B front panel FPIM connections. The backplane connection

provides power to the 7F06-02 Module and a channel for

communication with the 7X00 SmartSwitch Control Module. The

two front panel FPIMs provide FDDI connections, allowing the use

of single mode or multimode ﬁber cable with MIC or SC type

connectors.

1-4

INTRODUCTION

1.4 RELATED MANUALS

The manuals listed below should be used to supplement the

procedures and other technical data provided in this manual. The

procedures will be referenced, where appropriate, but will not be

repeated.

7X00 SmartSwitch Control Module User’s Guide

7F06-02 Local Management Appendix

7C03 MMAC SmartSwitch Installation Guide

7C04 Workgroup SmartSwitch Installation Guide

7C04-R Workgroup SmartSwitch Installation Guide

1.5 GETTING HELP

If you need additional support with the 7C03 MMAC

SmartSWITCH, or if you have any questions, comments or

suggestions concerning this manual, contact Cabletron Systems

Technical Support:

By phone:

(603) 332-9400

By fax:

(603) 337-3075

By World Wide Web:

http://www.cabletron.com

GO CTRON from any ! prompt

[email protected]

(603) 335-3358

By CompuServe :

By Internet mail:

By BBS:

By mail:

Cabletron Systems, Inc.

P.O. Box 5005

Rochester, NH 03866-5005

1-5

CHAPTER 2

NETWORK REQUIREMENTS

Before installing Cabletron Systems 7F06-02 Module, review the

network requirements outlined in this chapter. All requirements

included in this chapter should be met to ensure satisfactory

performance of the 7F06-02 Module. Failure to do so may result in

unsatisfactory network performance.

Appendix A

2.1 FPIM MODULE SPECIFICATIONS

This module uses Fiber Port Interface Modules (FPIM) to provide

front panel cable connections. The FPIMs are user-installable. See

Section 3.2 I NSTALLING F P IMS.

2.1.1 FPIM-00 and FPIM-01

The FPIM-00 and FPIM-01 provide a multimode ﬁber connection.

The FPIM-00 uses a MIC style connector and the FPIM-01 uses an

SC type connector. The speciﬁcations for both devices are listed in

Table 2-1.

Table 2-1. FPIM-00 and FPIM-01 Speciﬁcations

Worst

Case

Budget

Typical

Value

Worst

Case

Typical

Budget

Parameter

Receive

Sensitivity

-30.5 dBm

-7.6 dBm

-28.0 dBm

-8.2 dBm

—

Peak Input

Power

—

2-1

NETWORK REQUIREMENTS

Transmitter power parameters are listed in Table 2-2.

Table 2-2. Transmitter Power Parameters

Worst

Case

Budget

Typical

Value

Worst

Case

Typical

Budget

Parameter

50/125 µm

-13.0 dBm

-10.0 dBm

-7.0 dBm

-15.0 dBm

-12.0 dBm

-9.0 dBm

13.0 dB

16.0 dB

19.0 dB

17.5 dB

20.5 dB

23.5 dB

ﬁber

62.5/125

µm ﬁber

100/140

µm ﬁber

Error Rate

Betterthan

10^-10

The link distance is up to 2 kilometers on the multimode ﬁber-

optic cable as speciﬁed by ANSI MMF-PMD.

2-2

NETWORK REQUIREMENTS

2.1.2 FPIM-02 and FPIM-04

The FPIM-02 has an RJ-45 connector supporting an Unshielded

Twisted Pair (UTP) connection. The FPIM-04 has an RJ-45

connector supporting a Shielded Twisted Pair (STP) connection.

The pinouts for both are listed in Table 2-3.

Table 2-3. FPIM-02 and FPIM-04 Pinouts

Pin Number

Represents

Transmit+

Transmit-

Pin Number

Represents

Receive+

Receive-

The link distance is up to 100 meters on unshielded twisted pair

cable as speciﬁed by ANSI TP-PMD.

2-3

NETWORK REQUIREMENTS

2.1.3 FPIM-05 and FPIM-07

The FPIM-05 and FPIM-07 provide a Single-mode ﬁber connection.

The FPIM-05 uses a MIC style connector and the FPIM-07 uses an

SC type connector. The speciﬁcations for both devices are listed in

Table 2-4.

Table 2-4. FPIM-05 and FPIM-07 Speciﬁcations

Parameter

Typical

Minimum Maximum

Transmitter Peak

Wave Length

1300 nm

1270 nm

1330 nm

Spectral Width

Rise Time

60 nm

100 nm

5.0 nsec

50.7%

3.0 nsec

2.5 nsec

50.1%

2.7 nsec

2.2 nsec

49.6%

Fall Time

Duty Cycle

Bit Error Rate

Better

than 10^-10

The link distance is up to 40 kilometers (max) and 25 kilometers

(typical) on single mode ﬁber-optic cable as speciﬁed by ANSI

SMF-PMD.

2-4

CHAPTER 3

INSTALLATION/REMOVAL

This chapter contains instructions for unpacking and installing the

7F06-2 Module in the:

• 7C03 MMAC SmartSwitch

• 7C04 Workgroup SmartSwitch

• 7C04-R Workgroup SmartSwitch.

Also included in the chapter are instructions the front panel FPIMs.

3.1 UNPACKING THE 7F06-2 MODULE

Unpack the 7F06-2 Module by using the following steps:

1. Carefully remove the module from the shipping box. (Save the

box and packing materials in the event the module must be

reshipped.)

2. Remove the module from the plastic bag. Observe all

precautions to prevent damage from Electrostatic Discharge

(ESD).

3. Carefully examine the module and check for damage. If damage

exists, DO NOT install the module; contact Cabletron Systems

Technical Support.

3.2 INSTALLING FPIMS

The 7F06-02 module is shipped without FPIMs. To install an FPIM,

follow the procedure below:

1. Remove the module if it is installed in the 7C03 MMAC

SmartSWITCH chassis by reversing the procedure in

Section 3.3.

2. Remove the blank front cover over the FPIM slot.

3. Install the FPIM as shown in Figure 3-1. Ensure that the rear

connector is seated ﬁrmly before tightening the two mounting

screws.

3-1

INSTALLATION/REMOVAL

Figure 3-1. Installing an FPIM

3.3 INSTALLING/REMOVING THE 7F06-02 MODULE

The following procedure detail the installing and removal procedure for

the 7F06-02 module.

3.3.1 Installing in the 7C03 SmartSwitch

The 7F06-02 Module is installed in the 7C03 MMAC SmartSwitch

using the following steps and referring to Figure 3-2.

3-2

INSTALLATION/REMOVAL

Notes: The left most slot in the 7C03 MMAC SmartSwitch is reserved for

the 7X00 SmartSwitch Module.

Before installing the 7F06-02 module, attach the wrist strap

included with the SmartSwitch or SmartSwitch module by

following the instructions printed on the package.

1. Remove the blank panel covering the slot in which the module will be

installed. All other slots must remain covered to ensure proper airﬂow

and cooling.

2. Install the module by sliding it into slots as shown in Figure 3-2.

Ensure that the printed circuit board (PCB) is between the card guides,

slides in straight, and engages the backplane connectors properly.

3. Using a slotted screwdriver, tighten the top and bottom screws.

TPRMI

TPR

CPU

Card

Guides

Figure 3-2. Installing the 7F06-02 Module in the

7C03 MMAC SmartSwitch

3.3.2 Removing from the7C03 SmartSwitch

The 7F06-02 Module inserted in the 7C03 MMAC SmartSwitch can

be removed whenever necessary. Follow the steps below and refer

to Figure 3-3 to remove the module.

3-3

INSTALLATION/REMOVAL

Note: Before removing the 7F06-02 module, attach the wrist strap

included with the SmartSwitch or SmartSwitch module by

following the instructions printed on the package.

1. Use a slotted screwdriver to loosen the two screws that secure the

module to the chassis.

2. Locate the two ejector tabs on the module (to the right of the screws on

the top and bottom of the module).

3. Simultaneously press down on the bottom ejector tab and up on the

top ejector tab until the module ejects from the backplane.

4. Grasp both ejector tabs and carefully slide the module out of the

chassis.

7X00

PWR

7F00

7E03-24

CPU

MAC ADR

Screws

Ejector

Tabs

Figure 3-3. Removing the 7F06-02 Module from the 7C03 MMAC

SmartSwitch

3-4

INSTALLATION/REMOVAL

3.3.3 Installing in the 7C04 or 7C04-R Workgroup

SmartSwitch

The 7F06-02 Module is installed in the 7C04 or 7C04-R Workgroup

SmartSwitch using the following steps and referring to the

appropriate ﬁgure.

Notes: The top slot in the 7C04 Workgroup SmartSwitch is reserved for

the 7X00 SmartSwitch Module.

The bottom slot in the 7C04-R Workgroup SmartSwitch is

reserved for the 7X00 SmartSwitch Module.

Before installing the 7F06-02 module, attach the wrist strap

included with the SmartSwitch or SmartSwitch module by

following the instructions printed on the package.

1. Remove the blank panel covering the slot in which the module will be

installed. All other slots must remain covered to ensure proper airﬂow

and cooling.

2. Install the module by sliding it into slots as shown in the appropriate

ﬁgure. Ensure that the printed circuit board (PCB) is between the card

guides, slides in straight, and engages the backplane connectors

properly.

3. Using a slotted screwdriver, tighten the top and bottom screws.

3-5

INSTALLATION/REMOVAL

Figure 3-4. Installing the 7F06-02 Module in the 7C04 Workgroup

SmartSwitch

FANS

Figure 3-5. Installing the 7F06-02 Module in the 7C04-R Workgroup

SmartSwitch

3-6

INSTALLATION/REMOVAL

3.3.4 Removing from the 7C04 or 7C04-R Workgroup

SmartSwitch

The 7F06-02 Module, inserted in the 7C04 or the 7C04-R

Workgroup SmartSwitch, can be removed whenever necessary.

Follow the steps below and refer to the appropriate ﬁgure to

remove the module.

Note: Before removing the 7F06-02 module, attach the wrist strap

included with the SmartSwitch or SmartSwitch module by

following the instructions printed on the package.

1. Use a slotted screwdriver to loosen the two screws that secure the

module to the chassis.

2. Locate the two ejector tabs on the module (below the screws on the left

and right end of the module).

3. Simultaneously press left on the left ejector tab and right on the right

ejector tab until the module ejects from the backplane.

4. Grasp both ejector tabs and carefully slide the module out of the

chassis.

Screws

Ejector Tabs

Figure 3-6. Removing the 7F06-02 Module from the 7C04 Workgroup

SmartSwitch

3-7

INSTALLATION/REMOVAL

Screws

FANS

Ejector Tabs

Figure 3-7. Removing the 7F06-02 Module from the 7C04-R Workgroup

SmartSwitch

3-8

CHAPTER 4

TROUBLESHOOTING

The 7F06-02 Module uses LANVIE W, Cabletron Systems built-in

visual diagnostic and status monitoring system.

With LANVIEW LEDs the status of each transmit and receive port

on the 7F06-02 Module can be determined, at a glance. This section

discusses the function and purpose of the LEDs on the 7F06-02

Module.

Figure 4-1 shows the LANVIEW LEDs of the 7F06-02 Module.

7F06-02

A Link Status

Primary

Ring

B Link Status

Secondary

Ring

Receive

Transmit

Figure 4-1. The LANVIEW LEDs

4-1

TROUBLESHOOTING

Table 4-1 indicates the state of the receive port.

Table 4-1. Port Receive LEDs

LED Color

State

Yellow (Flashing)

Data activity (ﬂashing to steady on

indicates rate)

Off

No activity, port can be disabled or

enabled

Table 4-2 indicates the state of the transmit port.

Table 4-2. Port Transmit LEDs

LED Color

State

Green (Flashing)

Data activity (ﬂashing to steady on

indicates rate)

Off

No activity, port can be disabled or

enabled

4-2

TROUBLESHOOTING

Table 4-3 indicates the state of the A/B Link LEDs.

Table 4-3. Link LEDs

State

Green

N/A

Off

Green

Ports Enabled & Active

Green

THRU A, MAC on Primary,

Secondary Bypasses Board

Green

Off

Yellow Green

THRU A, MAC on Primary,

No MAC on Secondary

Green

THRU B, MAC on Secondary,

Primary Bypasses Board

Yellow Green

Yellow Off

THRU B, MAC on Secondary,

No MAC on Primary

THRU, No MAC on Primary,

Secondary Bypasses Board

Off

Yellow Green

THRU, No MAC on

Secondary, Primary Bypasses

Board

Green

Red

Yellow WRAP A, MAC on Primary

Yellow Red

Yellow WRAP A, No MAC on

Primary

Yellow Green

Red

Green

WRAP B, MAC on Primary

WRAP B, No MAC on Primary

WRAP AB, MAC on Primary

BYPASS Primary & Secondary

TWISTED A-A, B-B

Yellow Yellow Red

Green

Off

Red

Off

Red

Off

Yellow Off

Yellow PCM did not complete, Not

Active

Red Off

Off

Red

Ports Disabled

4-3

CHAPTER 5

TECHNICAL SPECIFICATIONS

This chapter includes the technical speciﬁcations for Cabletron

Systems 7F06-02 module. Cabletron Systems reserves the right to

change these speciﬁcations at any time without notice.

5.1 STANDARDS

IEEE 802.1D

IEEE 802.3i 10BASE-T

5.2 EMI

The EMI requirements of:

• FCC Part 15 Class A

• EN 55022 Class A

• VCCI Class I

5.3 EMC

The EMC requirements of:

• EN 50082-1

• IEC 801-2 ESD

• IEC 801-3 Radiated susceptibility

• IEC 801-4 EFT

5.4 NETWORK INTERFACES

Two FPIMs

5-1

TECHNICAL SPECIFICATIONS

5.5 SAFETY

It is the responsibility of the person who sells the system to which

the module will be a part to ensure that the total system meets

allowed limits of conducted and radiated emissions.

This equipment meets the safety requirements of:

• UL 1950

• CSA C22.2 No. 950

• EN 60950

• IEC 950

5.6 SERVICE

MTBF

MTTR

>200,000 hours

<0.5 hour

5.7 PHYSICAL

5.7.1 Dimensions

31.1D x 22.9 H x 3.1 W centimeters

(12.3 D x 9.0 H x 1.2 W inches)

5.7.2 Weight

Unit:

1.8 kgs. (4 lbs.)

4.5 kgs. (10 lbs.)

Shipping:

5-2

Black Box Network Hardware 8x8 DVI D Matrix Switches User Manual
Black Box Surge Protector SP250A User Manual
Black Decker Vacuum Cleaner VE100K User Manual
Bosch Appliances Automobile Electronics 0 User Manual
Bosch Appliances Coffeemaker TKN68E75UC User Manual
Bosch Appliances Security Camera VG4 User Manual
Brother Sewing Machine NX 400Q User Manual
Bryan Boilers Boiler BE 210 W4T7 User Manual
Canon Camera Lens 4657A006 User Manual
Canon Network Card MA 52 User Manual