Before using this machine for the first time, read this Quick Setup
Guide to setup and install your machine.
To view the Quick Setup Guide in other languages, please visit
Quick Setup Guide
ENG
Note: Not all models are available in all countries.
HL-4140CN
(EU Only)
Version 0
HL-4150CDN
Unpack the machine and check the components
Note
WARNING
1
• The components included in the box may differ depending on your
country.
• Plastic bags are used in the packaging of your machine. Plastic
bags are not toys. To avoid danger of suffocation, please keep these
bags away from babies and children and dispose of them properly.
• We recommend that you save the original packaging.
Documentation/Installation
CD-ROM(s)
• If for any reason you must ship your machine, carefully repack
the machine in the original packaging to avoid any damage during
transit. The machine should be adequately insured with the
carrier. How to repack the machine, see Shipment of the machine
in the User’s Guide.
Quick Setup Guide
Safety and Legal Booklet
AC Power Cord
• This machine is heavy and weighs approximately 21.0 kg (46.3 lb.).
To prevent possible injuries at least two people should lift the
machine. Be careful not to pinch your fingers when you put the
machine down.
Start Here
• The interface cable is not a standard accessory. Buy the
appropriate interface cable for the interface you want to use (USB
or Network).
• If you use a Lower Tray, carry it separately from your machine.
WARNING indicates a potentially
hazardous situation which, if not avoided,
could result in death or serious injuries.
WARNING
USB cable
CAUTION indicates a potentially
hazardous situation which, if not avoided,
may result in minor or moderate injuries.
Drum Unit
Waste Toner Box
Belt Unit
Starter Toner Cartridges
Note
It is recommended to use a USB 2.0 (Type A/B) interface cable that
is no longer than 2 meters (6 feet).
CAUTION
(pre‑installed)
(pre‑installed)
(pre‑installed)
(pre‑installed)
Keep a minimum gap around the machine as shown in the illustration.
(Black, Cyan, Magenta and Yellow)
Network cable
200 mm (7.87 in.)
(HL‑4150CDN) In USA:
Use a straight‑through Category5 (or greater) twisted‑pair cable for
10BASE‑T or 100BASE‑TX Fast Ethernet Network.
Please go to the Brother Solutions Center at
http://solutions.brother.com/ and click Manuals on your model page to
download the other manuals.
250 mm
(9.84 in.)
100 mm
100 mm
(4.00 in.)
(4.00 in.)
Remove the packing material from the machine
Load paper in the paper tray
c. Press the front cover release
f. Remove the 4 orange
a. Pull the paper tray completely
d. Put paper in the tray and make
sure:
e. Put the paper tray firmly
back in the machine. Make
sure that it is completely
inserted into the machine.
IMPORTANT
2
4
3
button and open the front cover.
packing pieces.
out of the machine.
DO NOT plug in the AC power cord yet.
Remove the silica gel pack a.
The paper is below the maximum
paper mark (▼▼▼) a.
Over filling the paper tray will
cause paper jams.
The side to be printed on must
be face down.
The paper guides touch the
sides of the paper so it will feed
properly.
g. Push the drum unit firmly
b. While pressing the green
paper‑guide release lever a,
slide the paper guides to fit the
paper size you are loading in the
tray. Make sure that the guides
are firmly in the slots.
back into the machine.
CAUTION
DO NOT eat Silica Pack. Discard
immediately.
a. Remove the packing tape from the outside of the
For more information about
recommended paper, see
Recommended paper and
print media in the User’s
Guide.
h. Close the front cover of
machine.
the machine.
b. Open the MP tray a, and remove the plastic sheet
b from the MP tray support, then close the MP tray.
d. Hold the green handle of the
drum unit and pull it out until it
stops.
c. Fan the stack of paper well to
avoid paper jams and misfeeds.
e. Hold the orange packing
material, and remove it.
Print a test page
Set your language
c. After the machine has finished warming up, the LCD will
d. Press Go. The machine will print a test page. Check
a. Press + or − to choose General Setup.
Press OK.
IMPORTANT
5
show Ready.
that the test page has printed correctly.
DO NOT connect the Interface cable yet.
b. Press OK to choose Local Language.
c. Press + or − to choose your language.
Press OK.
Note
Note
You can adjust the angle of the display by lifting it.
This function will not be available after the first print job you
send from your computer.
a. Connect the AC power cord to the machine and then
connect it to an AC power outlet.
Now go to
b. Remove the label covering the machine’s power
switch, and then switch the machine on.
Turn the sheet over to install the printer driver.
Options
Consumables
For Network Users
The machine has the following optional accessories. You can expand the capabilities of
the machine by adding these items. For more information about the optional Lower Tray
When the time comes to replace consumable items, an error will be indicated by the LCD
on the control panel. For more information about the consumables for your machine, visit
Web Based Management (web browser)
The Brother print server is equipped with a web server that allows
you to monitor its status or change some of its configuration
settings, using HTTP (Hyper Text Transfer Protocol).
Reset the network settings to the
factory default
To reset all network settings of the print server to its
factory default, follow the steps below.
For installing the SO‑DIMM Memory, see Installing extra memory in the User’s Guide.
Toner cartridges
Drum unit
Lower Tray Unit (LT-300CL)
SO-DIMM Memory
Note
a. Press + or − to choose Network.
Press OK.
Second lower paper tray unit can hold up to
500 sheets of paper. When the tray is installed,
the machine expands total input capacity up to
800 sheets.
You can increase the memory
by installing one SO‑DIMM
(Small Outline Dual In‑line
Memory Module).
• The login name for the Administrator is ‘admin’ (case sensitive) and
the default password is ‘access’.
(where machine_ip_address is the IP Address or the print
server name).
b. Press + or − to choose Network Reset.
Press OK.
• We recommend Microsoft® Internet Explorer® 6.0 (or greater) or
Firefox 3.0 (or greater) for Windows® and Safari 3.0 (or greater) for
Macintosh. Please also make sure that JavaScript and Cookies are
always enabled in whichever browser you use. To use a web browser,
you will need to know the IP Address of the print server. The IP
Address of the print server is listed on the Print Setting Page.
Belt Unit (BU-300CL)
Waste Toner Box (WT-300CL)
c. Press + to choose Reset.
See Web Based Management in the Network User’s Guide.
d. Press + to choose Yes for reboot.
The machine will re‑start.
For replacing the consumable items, see Replacing consumable items in the User’s Guide.
|