Bose Speaker 369946 1300 User Manual

®
®
Bose SoundLink  
®
Bluetooth speaker III  
Owner’s Guide  
 
Safety  
WARNING: This product contains magnetic material. Please contact your physician if you have any  
questions on whether this might affect the operation of your implantable medical device.  
CAUTION: Make no modifications to the system or accessories. Unauthorized alterations may  
compromise safety, regulatory compliance, and system performance.  
NOTES:  
• The product label is located on the bottom of the product.  
Where the mains plug or appliance coupler is used as the disconnect device, such disconnect device shall remain  
readily operable.  
• The AC power supply provided with this product must be used indoors. It is neither designed nor tested for use  
outdoors, in recreation vehicles, or on boats.  
• This product is intended to be used only with the AC power supply provided, or a Bose® AC power supply or  
charger designed for use with this product.  
Important Safety Instructions  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with a dry cloth.  
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.  
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus  
(including amplifiers) that produce heat.  
9. Only use attachments/accessories specified by the manufacturer.  
10. Unplug this apparatus during lightning storms or when unused for long periods of time.  
11. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any  
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the  
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has  
been dropped.  
Information about products that generate electrical noise  
This device complies with FCC and Industry Canada RF radiation exposure limits set forth for general population.  
It must not be co-located or operating in conjunction with any other antennas or transmitters.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
English - 3  
 
Safety  
U.S.A. only  
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to  
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference  
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications not expressly approved by Bose Corporation could void the user’s authority to operate  
this equipment.  
Canada  
This Class B digital apparatus complies with Canadian ICES-003.  
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following  
two conditions: (1) This device may not cause interference, and (2) this device must accept any interference,  
including interference that may cause undesired operation of the device.  
Output power: 7 mW @ 2400-2483.5 MHz  
Bose Corporation hereby declares that this product is in compliance with the essential requirements and  
other relevant provisions of Directive 1999/5/EC and to all applicable EU directive requirements.  
Names and Contents of Toxic or Hazardous Substances or Elements  
Toxic or Hazardous Substances and Elements  
Lead  
Part Name (Pb)  
Mercury  
(Hg)  
Cadmium  
(Cd)  
Hexavalent  
(CR(VI))  
Polybrominated Polybrominated Diphenyl  
Biphenyl (PBB)  
Ether (PBDE)  
PCBs  
Metal  
parts  
X
X
0
0
0
0
0
0
0
0
0
0
Plastic  
parts  
0
0
0
0
0
0
Speakers  
Cables  
X
X
0
0
0
0
0
0
0
0
0
0
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is  
below the limit requirement in SJ/T 11363-2006.  
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used  
for this part is above the limit requirement in SJ/T 11363-2006.  
Please complete and retain for your records.  
The serial and model number can be found on the bottom of the speaker.  
Serial number: ___________________________________________________________________  
Model number: __________________________________________________________________  
Purchase date: __________________________________________________________________  
We suggest you keep your receipt with this owner’s guide.  
4 - English  
 
Contents  
Introduction  
Overview..............................................................................................................  
6
6
Unpacking...........................................................................................................  
Operation  
Connecting to AC power...................................................................................  
Pairing and connecting a device to the speaker..........................................  
First-time setup..........................................................................................  
7
9
9
Adding another device to the speaker ................................................... 10  
Speaker memory ........................................................................................ 10  
Reconnecting a device .............................................................................. 10  
Switching to a different device................................................................ 10  
Control buttons..................................................................................................  
11  
System status indicators................................................................................. 12  
Connecting a device using the AUX connector............................................ 13  
Operating on battery power ............................................................................ 14  
Checking the battery ................................................................................. 14  
Charging the battery ................................................................................. 14  
Battery protection mode .......................................................................... 14  
Tips on placing the speaker............................................................................. 15  
Maintenance and Care  
Troubleshooting ................................................................................................ 16  
Replacing the battery ....................................................................................... 18  
Cleaning the speaker ........................................................................................ 18  
Contacting customer service .......................................................................... 18  
Technical information ...................................................................................... 18  
English - 5  
 
Introduction  
Overview  
®
®
®
Thank you for purchasing the Bose SoundLink Bluetooth speaker III. Enjoy  
music wirelessly from your smartphone, tablet, laptop, or other Bluetoothdevice  
anywhere you choose.  
Features  
Wireless Bluetooth link eliminates the need to physically connect your  
Bluetooth device.  
Rechargeable lithium-ion battery provides hours of Bose performance.  
AUX connector lets you connect any music device directly to your speaker.  
Pair up to six Bluetooth devices.  
Easy grab-and-go mobility.  
Unpacking  
Open the carton and remove the speaker and AC power supply. Depending on  
your region, the carton may also contain AC power adapters for the AC power  
supply. Be sure to save all of the packing materials. These provide the safest  
means for any necessary shipping or transporting of the system.  
If any part of the product appears to be damaged, do not attempt to use it.  
Contact your authorized Bose dealer immediately or call Bose Customer Service.  
For contact information, refer to the contact list at the end of this guide or visit  
®
®
SoundLink Bluetooth speaker III  
AC power supply  
AC power supply  
adapters  
6 - English  
 
Operation  
Connecting to AC power  
®
®
The first time using your SoundLink Bluetooth speaker III, connect it to AC  
(mains) power and charge the battery for three hours. While the battery is charging,  
you can begin using the speaker.  
1. Depending on your AC power supply type:  
a. Extend the prongs from the AC power supply.  
Or,  
b. Slide the AC power adapter for your region onto the AC power supply.  
English - 7  
 
Operation  
2. Plug the power cord on the AC power supply into the DC connector on the  
back of the speaker.  
3. Plug the AC power supply into a live AC (mains) outlet.  
The speaker emits a tone to confirm connection to AC power, and charging  
begins. On the front of the speaker, the battery status indicator  
yellow to show the battery is charging.  
blinks  
8 - English  
 
Operation  
Pairing and connecting a device to the speaker  
®
®
®
Before listening to music from your Bose Soundlink Bluetooth speaker III, you  
must pair and connect your Bluetooth device to the speaker.  
First-time setup  
The first time you turn on your speaker, it is ready to pair and connect your  
first device.  
1. Press Power  
to turn the speaker on.  
The Bluetooth status indicator on the speaker blinks blue to show the  
speaker is discoverable.  
2. On your device, turn Bluetooth on, locate the Bluetooth device list, and select  
the device named “Bose SLIII.” If your device prompts you for a passcode,  
enter “0000” (four zeros).  
Settings  
Bluetooth  
ON  
Bluetooth  
Devices  
Connected  
Bose SLIII  
When pairing is complete and your device is connected to the speaker, the  
Bluetooth status indicator on the speaker changes from blinking blue to  
solid white and the speaker emits a tone.  
Note: If the speaker turns off after five minutes, it has not paired or connected with  
your device. Turn the speaker off and back on, and try pairing your device  
again. See “Troubleshooting” on page 16.  
English - 9  
 
Operation  
Adding another device to the speaker  
Pair another device to the speaker by making the speaker discoverable.  
®
1. Press Bluetooth  
on the speaker, so the Bluetooth status indicator  
blinks blue.  
2. On your device, turn Bluetooth on, locate the Bluetooth device list, and select  
the device named “Bose SLIII.” If your device prompts you for a passcode,  
enter “0000” (four zeros).  
When the device connects to the speaker, the Bluetooth status indicator turns  
to solid white.  
Note: You can switch between connecting/connected and discoverable by  
pressing Bluetooth on the speaker.  
Speaker memory  
The speaker can remember up to six paired devices. If you pair the speaker with  
an additional device, the device least recently connected is no longer paired with  
the speaker.  
Note: To clear the speaker memory of all devices, press and hold Bluetooth  
(about 10 seconds) until you hear a tone. All devices are cleared and the  
speaker becomes discoverable.  
Reconnecting a device  
When turned on, the speaker attempts to reconnect with a device in memory  
starting with the last connected device. If the last connected device is not  
available, the speaker connects to the next to last connected device, and so forth.  
The speaker searches for a paired device for approximately 30 seconds.  
Switching to a different device  
You can switch the speaker from your connected device to another previously  
paired device. The device you are switching to must be in the speaker memory.  
1. On your previously paired device, make sure Bluetooth is turned on.  
2. Press Bluetooth on the speaker to make the speaker discoverable.  
The Bluetooth status indicator speaker blinks blue to show the speaker  
is discoverable.  
3. On your device, select “Bose SLIII” from the Bluetooth device list.  
The Bluetooth status indicator blinks white, while the speaker attempts to con-  
nect to the device.  
When the speaker and Bluetooth device have successfully connected, the  
Bluetooth status indicator changes from blinking to solid white and the  
speaker emits a tone.  
10 - English  
 
Operation  
Control buttons  
Control buttons are located on the top of the speaker.  
Control  
button  
Description  
Press to turn the speaker on or off.  
®
When Bluetooth is the selected source, the speaker attempts to  
reconnect to the last connected device. If there are no paired devices,  
the speaker becomes discoverable. See “Pairing and connecting a device  
to the speaker” on page 9.  
If operating on battery power, press and hold to observe the battery  
status indicator. See “Checking the battery” on page 14.  
If the speaker is not used within 30 minutes, the speaker automatically  
turns off to preserve battery power.  
Press to select the Bluetooth source.  
The speaker attempts to connect to the last paired device. If there are no  
paired devices, the speaker becomes discoverable.  
If Bluetooth is connecting/connected, press to set the speaker to  
discoverable to allow pairing with another Bluetooth device. Press again to  
go back to connecting mode.  
Press to listen to a device plugged into the AUX connector. See “Connecting  
a device using the AUX connector” on page 13.  
Press to mute/unmute sound from the speaker.  
Press to decrease the speaker volume incrementally. Press and hold to  
decrease the volume continuously.  
Press to increase the speaker volume incrementally. Press and hold to  
increase the volume continuously.  
English - 11  
 
Operation  
System status indicators  
Status indicators illuminate to show when an audio source or speaker state is  
activated. Status indicators are located on the front of the speaker.  
Status  
indicator System status  
®
Indicates the Bluetooth state of the speaker when the Bluetooth source  
is selected. See “Pairing and connecting a device to the speaker” on  
page 9.  
Blinking blue light Discoverable and ready to pair with a device.  
Blinking white light – Attempting to connect to a paired device.  
Solid white light Connected to a paired device.  
Blinks as the volume of the speaker increases or decreases when  
Bluetooth is the source. When the indicator blinks twice, the maximum or  
minimum volume has been reached.  
The speaker is playing the source connected to the AUX IN  
connector.  
Blinks as the volume of the speaker increases or decreases when AUX is  
the source. When the indicator blinks twice, the maximum or minimum  
volume has been reached.  
Blinks when the sound is muted.  
Indicates the battery power level or the battery charging state. See “Checking  
the battery” on page 14.  
12 - English  
 
Operation  
Connecting a device using the AUX connector  
You can use your speaker with any device that features a headphone or audio  
output. This feature requires using a stereo audio cable with a 3.5 mm plug on  
one end to connect to the AUX IN input  
on the speaker. This type of cable is  
available for purchase at electronics stores.  
To use the AUX IN connector:  
1. Plug the cable from your audio device into the AUX IN connector  
on the  
back of the speaker.  
2. Press Power  
on the speaker.  
3. Press AUX on the speaker.  
4. Adjust the volume on the connected device to near maximum, then use  
the speaker volume buttons to adjust the volume level.  
Notes:  
If the connected device stops playing audio for 30 minutes, the speaker  
automatically turns off to conserve battery power.  
The SERVICE connector on the back of the speaker is only for software updates.  
It cannot be used to connect an audio device.  
English - 13  
 
Operation  
Operating on battery power  
Battery performance varies with the content played and the loudness at which  
it is played. In typical usage, the speaker battery lasts up to 14 hours.  
Checking the battery  
When the speaker is turned on, the battery status indicator briefly illuminates, then  
turns off to conserve battery power. However, if the battery requires charging, the  
battery status indicator illuminates and continuously blink red until the speaker the  
speaker is connected to AC power and the battery begins charging.  
To check the battery charge level, press and hold Power  
observe the battery status indicator.  
on the speaker and  
Solid green  
Solid yellow  
Blinking red  
Full charge  
Medium charge  
Charging is needed  
Charging the battery  
The battery status indicator on the speaker blinks red when the battery needs  
charging.  
To charge the battery, connect the speaker to AC power (see “Connecting to AC  
power” on page 7). The speaker emits a tone to confirm the power connection.  
Recommended charging time is three hours to fully charge the battery. The battery  
status indicator indicates the charging status. You can use the speaker while  
charging the battery.  
Blinking yellow  
Solid green  
Battery is charging  
Battery is fully charged  
Battery protection mode  
When the speaker is unplugged and unused for more than 24 days, it enters  
battery protection mode to preserve battery power. To reactivate the speaker,  
connect it to AC power (see “Connecting to AC power” on page 7).  
14 - English  
 
Operation  
Tips on placing the speaker  
When using your speaker indoors, the tonal quality can vary depending on where  
the speaker is placed in a room.  
When using your speaker outdoors, you should expect the tonal quality to change  
as you move farther away from the speaker.  
Follow these guidelines when placing your speaker:  
The speaker is designed to sound best when placed on a surface that is 24 to 48  
inches high.  
For best bass response, the back of the speaker should be placed near a wall,  
but not directly against a wall. Bass response decreases as the speaker is  
moved away from a wall. Do not lay the speaker on its back. Sound is emitted  
from both the front and the rear of the speaker.  
Do not place the speaker in small areas where the speaker is enclosed on all  
sides except the front, as this will adversely affect sound quality.  
Do not place the speaker on wet or dirty surfaces.  
English - 15  
 
Maintenance and Care  
Troubleshooting  
Problem  
What to do  
Speaker will If using AC power, ensure:  
not turn on  
• Your system is connected to a working AC (mains) outlet.  
• You are using the Bose® AC power supply shipped with your speaker or a Bose  
accessory charger designed for the speaker.  
If using battery power, the battery may be in protection mode or discharged. Connect  
to a working AC outlet to restore the battery to operational mode and charge the  
battery.  
Cannot pair  
the speaker  
with my  
• Ensure your speaker is discoverable (Bluetooth status indicator blinks blue).  
See “Pairing and connecting a device to the speaker” on page 9.  
• Ensure Bluetooth is enabled on your device.  
• Ensure you have selected “Bose SLIII” in the Bluetooth device list on your device  
and the connection has been confirmed by your device.  
Bluetooth®  
device  
Your Bluetooth device may be out of range. Try moving it closer to the speaker.  
• If possible, turn off all other nearby Bluetooth devices or disable their Bluetooth  
functionality.  
• Ensure your device supports the A2DP (stereo Bluetooth) profile.  
• When pairing and connecting to a PC or Mac computer, ensure you have selected  
the SoundLink® Bluetooth® speaker III as the audio output device within the audio  
settings menu of the computer. You may need to play an audio track to finalize the  
connection (see the computer manufacturer for detailed instructions).  
Refer to the owner’s guide, help system, or technical support for your Bluetooth  
device to learn how it pairs with other Bluetooth devices.  
• Turn the speaker off and back on, and pair and connect your device.  
See “First-time setup” on page 9 and “Adding another device” on page <?>.  
Reset the speaker. Press and hold Mute on the speaker for ten seconds until all  
status indicators briefly illuminate and the speaker turns off. Turn the speaker on  
again, and pair your device.  
• Check for updated software for your Bluetooth device, or go to owners.Bose.com  
for updates to the SoundLink® Bluetooth® speaker III.  
Paired  
• Ensure your speaker is discoverable (Bluetooth status indicator blinks blue).  
Bluetooth  
device will not  
connect to  
the speaker  
See “Pairing and connecting a device to the speaker” on page 9.  
• Ensure Bluetooth is enabled on your device.  
• Your device may be out of range. Try moving it closer to the speaker.  
• Turn your device off and back on, and connect it to the speaker.  
See “Reconnecting a device” on page <OV>.  
• If possible, turn off all other nearby Bluetooth devices or disable their Bluetooth  
functionality.  
Reset the speaker. Press and hold Mute on the speaker for ten seconds until all  
status indicators briefly illuminate and the speaker turns off. Turn the speaker on  
again, and connect your device.  
• Clear the speaker memory. Pair and connect the device to the speaker again.  
See “Speaker memory” on page 10 and “First-time setup” on page 9.  
16 - English  
 
Maintenance and Care  
Problem  
What to do  
The speaker • Ensure the device you want to hear is connected to the speaker and playing audio.  
indicates a  
• Ensure the speaker is not muted and the speaker volume is turned up.  
Turn up the volume on your device.  
Your Bluetooth® device may be out of range. Try moving it closer to the speaker.  
connection,  
but is not  
playing music  
Move your device away from any device that generates electromagnetic  
interference, such as another Bluetooth device, cordless phone,microwave  
oven, or wireless router.  
• If possible, turn off all other nearby Bluetooth devices or disable their Bluetooth  
functionality and reconnect the device you want to hear.  
Refer to the owner’s guide, help system, or technical support for your Bluetooth  
device to learn how it pairs with other Bluetooth devices.  
• Turn the speaker off and back on.  
Reset the speaker. Press and hold Mute on the speaker for ten seconds until all  
status indicators briefly illuminate and the speaker turns off. Turn the speaker on  
again, and connect your device.  
Poor sound  
quality from  
a Bluetooth  
device  
Connect your Bluetooth device to the speaker using the AUX connection. If sound  
quality improves using the AUX connection, try these solutions:  
Your Bluetooth device may be out of range. Try moving it closer to the speaker.  
Move your device away from any device that generates electromagnetic  
interference, such as another Bluetooth device, cordless phone,microwave  
oven, or wireless router.  
• Reduce the number of applications running on your device. Running multiple  
applications can reduce the amount of internal resources available to transmit  
audio. Closing non-essential applications may improve audio quality.  
• Try turning off Wi-Fi® on your device to improve audio quality.  
• Try clearing your device from the speaker by disabling Bluetooth on your device.  
Pair your device and the speaker again.  
• If your device is in your pocket, try placing it in open air, without your body between  
the device and the speaker.  
• Turn the speaker off and back on.  
Reset the speaker. Press and hold Mute on the speaker for ten seconds until all  
status indicators briefly illuminate and the speaker turns off. Turn the speaker on  
again, and pair and connect your device.  
• Check for updated software for your Bluetooth device, or go to owners.Bose.com  
for updates to the SoundLink® Bluetooth® speaker III.  
No audio or  
poor sound  
quality from  
an AUX  
• Ensure your connected device is on and playing audio.  
• Ensure the 3.5 mm plug of the stereo cable is fully inserted into the speaker and  
the other end into the AUX device.  
• Press AUX on the speaker and ensure the AUX status indicator is on.  
• Ensure the speaker is not muted and the speaker volume is up.  
• If there is no sound, increase the volume level on the AUX device.  
• If sound quality is poor, reduce the volume level on the AUX device.  
• Try using a different AUX cable.  
device  
English - 17  
 
Maintenance and Care  
Replacing the battery  
The battery should be replaced when:  
The battery status indicator continues blinking yellow after ten hours of charging.  
The period of battery operation noticeably decreases.  
Only Bose can replace the battery in your speaker. If you need a new battery,  
please contact the Bose organization in your country/region. For contact  
information, refer to the contact list at the end of this guide or visit  
Cleaning the speaker  
To clean the exterior surface of your product, wipe it using a soft, dry cloth.  
Do not use solvents, chemicals, or sprays.  
Do not allow liquids to spill or objects to drop into any openings.  
Contacting customer service  
For questions about the Bose SoundLink Bluetooth speaker III, contact your  
local Bose dealer. For contact information, refer to the contact list at the end of this  
®
®
®
Limited warranty  
®
®
®
Your Bose SoundLink Bluetooth speaker III is covered by a limited warranty.  
Details of the limited warranty are provided on the product registration card  
included in the carton. Refer to the card for instructions on how to register.  
Failure to register will not affect your limited warranty rights.  
Technical information  
AC power supply rating  
Input: 100 - 240V , 50/60 Hz, 600 mA  
Output: 17 VDC, 1A Max  
Input power rating  
Input: 17 - 20 VDC, 1A Max  
Dimensions  
5.2" H x 10" W x 1.9" D (13.5 cm x 25.6 cm x 4.8 cm)  
Weight  
3.03 lb (1.37 kg)  
Temperature range for use  
32° to 113°F (0° to +45°C)  
18 - English  
 
Bose Corporation  
USA  
France  
Nederland  
Bose Corporation, The Mountain  
Framingham, MA 01701-9168  
1-800-901-0472  
Bose S.A.S.  
Bose B.V.  
12 rue de Témara  
78100 Saint Germain en Laye  
TEL 01 30 61 63 63  
FAX 01 30 61 63 60  
Nijverheidstraat 8  
1135 GE Edam  
TEL 0299-390290  
FAX 0299-390109  
Phone hours - ET (Eastern Time):  
Weekdays 8:30 a.m. to 8 p.m.  
Saturdays 9 a.m. to 3 p.m.  
owners.Bose.com  
Hong Kong  
Canada  
Suite 1203, Midas Plaza, 1 Iai  
Yau Street, San Po Kong  
Kowloon, Hong Kong  
TEL 852 2123 9000  
New Zealand  
TEL 0800 501 511  
Bose Limited  
280 Hillmount Road, Unit 5  
Markham, Ontario  
Canada L6C 3A1  
Norge  
India  
Bose A/S  
1-800-465-2673  
Bose Corporation India Private Limited  
The Bose Service Centre  
C13, Ground Floor  
Kongsvinger Festning  
2213 Kongsvinger  
TEL +47 62 82 75 00  
FAX +47 62 82 15 69  
Phone hours - ET (Eastern Time):  
Weekdays 9 a.m. to 5 p.m.  
SDA Commercial Complex  
Community Centre  
New Delhi, India 110016  
TEL 1 800 102 2673  
FAX +91 11 47168650  
Australia  
Poland  
Bose Pty Limited, Unit 3/2 Holker Street  
Newington NSW 2127  
TEL 1 800 061 046 (AU)  
TEL 008 501 511 (NZ)  
FAX 612 8737 9924  
Bose sp. z o.o.  
ul. Woloska 12  
02-675 Warszawa  
TEL 22-852-2928  
FAX 22-852-2927  
Ireland  
Bose SMS Ltd.  
Castleblayney Road  
Carrickmacross, Co Monaghan  
TEL 1-800-932-436  
FAX (042) 9671502  
Österreich  
Belgique/België  
Bose N.V., Limesweg 2  
B-3700 Tongeren  
TEL 012-259960  
FAX 012-390840  
Bose Ges.m.b.H.  
Vienna Business Park  
Wienerbergstrasse 7 (10.OG)  
A-1100 Vienna  
Italia  
Bose S.p.A. con socio unico  
Via Spadolini 5  
20141 Milano  
TEL 01-60404340  
FAX 01-604043423  
China  
Bose Greater China Operations  
1st Floor, EYON Building, No. 118  
East Dong Baoxing Road  
Shanghai 200080 P.R.C.  
People’s Republic of China  
TEL 400-880-2266  
TEL 06 60 292 292  
Schweiz  
Bose AG  
Japan  
Hauptstrasse 134  
4450 Sissach  
TEL 061-9757733  
FAX 061-9757744  
Bose K.K.  
Sumitomo Fudosan Shibuya  
Garden Tower 5F,  
16-17 Nampeidai-cho  
Shibuya-ku, Tokyo 150-0036  
TEL 0570-080-021  
FAX 03-5489-1041  
FAX 021-65105380  
Danmark  
Sverige  
Bose A/S, Industrivej 7  
2605 Brøndby  
Bose A/S  
Johannefredsgatan 4  
S-43153 Mölndal  
TEL +46 774 - 450 450  
FAX +46 31 - 274 89 15  
TEL 04343-7777  
FAX 04343-7818  
Luxemburg  
Bose N.V.  
Limesweg 2  
B-3700 Tongeren  
TEL +32 12 259 960  
FAX +32 12 390840  
Deutschland  
Bose GmbH  
Kundenbetreuung  
Neuenhauser Str. 73  
D-48527 Nordhorn  
TEL 0800 2673444  
United Kingdom  
Bose Limited  
1 Ambley Green  
Gillingham Business Park  
Gillingham, Kent ME8 ONJ  
TEL 0800 081 3569  
FAX 0870-741-4545  
Mexico  
Bose de Mexico S. de R.L. de C.V.  
Paseo de las Palmas # 405  
Despacho 204  
Finland  
Bose Finland  
Kornetintie 6B  
00380 Helsinki  
TEL 10 778 69 00  
FAX 10 778 69 09  
www.Bose.fi  
World Wide Web  
global.Bose.com  
Lomas de Chapultepec  
C.P. 11000, Mexico D.F., Mexico  
TEL +52 (55) 52 02 35 45  
TEL +52 (55) 52 02 41 95  
FAX +52 (55) 52 02 37 28  
English - 19  
 
©2013 Bose Corporation, The Mountain,  
Framingham, MA 01701-9168 USA  
AM373985 Rev. 00  
 

Beko Washer WCB75087 User Manual
BenQ CRT Television LW61ST User Manual
Black Box Computer Hardware IC181C User Manual
Bose Speaker System Cinemate Digital Home Theater Speaker System User Manual
Bravetti Mixer EP545XX User Manual
Briggs Stratton Portable Generator Home Generator System User Manual
Cambridge SoundWorks Stereo Amplifier AVS550 User Manual
Canon Projector LV 7340 User Manual
Capcom Video Games 7 User Manual
Cisco Systems IP Phone OL 20862 01 User Manual