BLUETREK® Skin user guide
Thank you for choosing the BLUETREK® Skin headset, we hope you will enjoy the
convenience we are bringing to you. The BLUETREK® Skin offers many functions,
please read this manual before getting started.
EC-Declaration of Conformity
We, Innovi Technologies Ltd of
31/F China Online Centre,
333 Lockhart Road,
Wan Chai, Hong Kong
declare under our sole responsibility that our product
BLUETREK Skin
to which this declaration refers is in conformity with the appropriate standards
EN300 328-02
EN301 489-17
EN301 489-01
EN50371
EN60950
Following the provisions of Radio and Telecommunications Terminal Equipment
directive 1999/5/EC.
September 2006
Guillaume Ponticelli, Director of Development
PAGE 1 / 9
BEFORE USING YOUR HEADSET FOR THE FIRST TIME
-
Pair the headset with a mobile phone. Please refer to the “Pairing the
BLUETREK® Skin” section of this manual.
Introduction
The BLUETREK® Skin headset is a wireless headset based on the Bluetooth®
technology. It complies with Bluetooth® 1.2 protocol, supporting Headset and Hands-
free profile.
PAGE 3 / 9
Charging the BLUETREK® Skin
Please connect the charger to the headset and to the main. During the charge, the
indicator light is red, the indicator light will turn off when the charge is complete. During
subsequent charges, the charging should take approximately 3 hours.
When you hear a low-tone beep in your headset at regular intervals, and the indicator
light flashes in red, your headset needs to be recharged.
Important:
• If your headset is fully charged, the red indicator light will not turn on when
plugging into the charger.
(To check whether your headset is fully charged, plug in the charger and press
the talk button for approx. 2 seconds. The red indictor light will turn on for approx.
3 seconds if the headset is fully charged.)
• To maximize battery lifetime, it is recommended to recharge your headset to full
capacity only when the battery is low, since a battery has a lifetime of about 500
charging cycles.
• If you leave your headset battery empty for an extended period of time, it could
excessively discharge the battery. In this case, charge your headset for 3 hours
or more until the battery recovers and recharges completely. When you first
charge the headset after prolonged storage, it may take few minutes for the red
indicator light to turn on.
• Do not charge your headset for more than 10 hours.
• The use of any other charger will automatically suspend the warranty. It is strictly
forbidden and can be very dangerous.
Pairing the BLUETREK® Skin
Before using the BLUETREK® Skin headset, you must pair it with your Bluetooth®
mobile phone. Pairing is the process of linking 2 Bluetooth® devices, so that they can
communicate.
To initiate pairing:
1. Place the BLUETREK® Skin and your mobile phone within 0.3 meter (1 foot) from
each other.
2. Switch on your phone and select its Bluetooth® discover mode (refer to the
Bluetooth® mobile phone user manual).
3. When the BLUETREK® Skin is switched off, press and hold the TALK button for
about 7 seconds until the indicator light flashes red and blue alternately. And a
sound can be heard in the speaker.
4. Once the mobile phone detects the headset, a “BLUETREK Skin” message will
be displayed. Follow the phone instructions to accept the pairing. The PIN code
(or passkey) is 0000, then press “yes” or “ok”.
If pairing was successful, the indicator light will switch to blue and flashes slowly.
If you haven’t started the discovery mode within 5 minutes, the headset will switch off.
You must then switch on your headset and start the pairing again.
PAGE 4 / 9
Wearing the BLUETREK® Skin
For your convenience, the ear hook of BLUETREK Skin is designed to be removable
and adjustable which allows the headset to be worn on either ear. BLUETREK® Skin,
as packaged, is ready to be worn on your right ear.
For left ear, simply unsnap the ear clamp
from the headset by pulling gently at the
case of the ear clamp ring.
The ear hook is made of a soft material
which can be shaped to fit your ear.
Flip the ear clamp over, and snap it back
onto the headset by applying gentle
pressure on the case of the ear clamp
ring.
Switching the BLUETREK® Skin ON and OFF
Switching BLUETREK® Skin ON
When your headset is off, press and hold the TALK button for about 2 seconds until the
blue indicator light is on. A beep (2 tones) can be heard in the speaker. Release the
TALK Button.
To check if your headset is ON, press once on the TALK button. If the indicator light
flashes blue, it means your headset is ON.
®
Switching BLUETREK Skin OFF
When your headset is on, press and hold the TALK button for about 5 seconds until the
red indicator light is on after the quick blue flashes. A beep (2 tones) can be heard in the
speaker then release the TALK button.
PAGE 5 / 9
Making a call
*Mobile phone with voice recognition
. Make sure the voice recognition function on your mobile is activated and your voice
tags have been recorded with the phone. To enter these, please refer to your phone’s
manual
. When there is no incoming or active call, press once on the TALK button
. Wait for the audio signal sent by the mobile phone (generally a short tone).
. Speak the name of person you wish to call.
Mobile without voice recognition
. Make sure both the headset and the mobile phone are ON and in stand-by mode.
. Dial the number on the phone keypad, after approximately 2 seconds the audio
connection will be established.
*This function may not be available on some phones, please refer to the trouble
Answering a call
When the headset rings, press once on the TALK button to take the call.
Ending a call
Press once on the TALK button to end an active call.
Adjusting the volume
To increase the volume during an active call, press the “VOL+” button on the headset.
To decrease the volume during an active call, press the “VOL-“ button on the headset.
Muting the microphone
To mute the microphone during an active call
During an active call, press and hold the VOL+ button for approximately 2 seconds. A
periodic tone can be heard in the speaker when the microphone is muted.
To end the mute function
When the microphone is muted, quickly press the VOL+ button on the BLUETREK® Skin.
The periodic tone will end.
Transferring a call from BLUETREK® Skin to the mobile phone
During an active call, press the TALK button for about 2 seconds.
(This function only works in the Hands-Free Profile.)
In the Headset profile, you can simply turn off your headset.
Transferring a call from the mobile phone to the BLUETREK® Skin
During an active call on the mobile phone, press once on the TALK button to transfer
the call.
PAGE 6 / 9
Pre-registered numbers feature
This feature allows you to store your 2 favourite numbers in your BLUETREK® Skin
headset and to dial these numbers directly from your headset.
(Important: This feature is only available in the Hands-free profile).
Storing your favourite numbers
1) Ensure your BLUETREK® Skin headset is paired and connected with your phone.
2) Enter numbers following the syntax describe below as your mobile phone name
(Please refer to your mobile phone manual to change your phone name. In most
phones, the mobile phone name is under the “Bluetooth” menu).
Example 1: To store “0123456789” in position 1 = 1S0123456789T
Example 2: To store “+44123456789” in position 2 = 2S+44123456789T
PAGE 7 / 9
3) Press and hold the “Vol-“ button on your BLUETREK® Skin headset for approx. 3
seconds, until the purple indicator light is on. (A beep can be heard in the
speaker).
4) - If the number is correct and have stored in the headset, you will hear:
1 beep in the speaker and the blue indicator light will flash once if the number has
been stored in position 1.
OR
2 beeps in the speaker and the blue indicator light will flash twice if the number has
been stored in position 2.
- If the number is incorrect, it will not store in the headset. You will hear a long low-
tone beep in the speaker and the red indicator light will flash twice.
Note:
1. Only 1 telephone number can be stored at one time. To store the second
number, simply repeat from Step 2.
2. Maximum of 2 favourite numbers can be stored and can be replaced by
repeating the above steps.
3. Remember to change back your mobile phone name once you have stored the
numbers.
Making a call to one of the stored numbers
1) Ensure your BLUETREK® Skin headset is paired and connected with your phone.
2) Press and hold the “Vol +” button on your BLUETREK® Skin headset until you
hear:
-
-
1 beep to call your number stored in position 1;
2 beeps to call your number stored in position 2.
Call waiting
When you hear a call waiting alert while you are on a call, press approx. 3 seconds on
the TALK button to accept the second call and place the current call on hold.
To switch between an active call and a hold call, press approx. 3 seconds on the TALK
button.
To end the active call and take the hold call, press once on the TALK button.
This function may not be available on some phones.
Additional features with some phones
Rejecting a call
When the headset rings, press the TALK button for about 2 seconds.
Redial the last number
When there is no incoming or active call, press the TALK button for about 2 seconds
until you hear a beep.
PAGE 8 / 9
Troubleshooting guide
The first thing you should do when encountering a problem that you cannot solve with
this manual, is to switch off your headset and your mobile phone, and switch them on
again.
To find out more, please refer to the trouble shooting frequent asked questions in our
Guidelines for safe use
Read those guidelines before using your headset.
-
-
-
-
-
Do not drop or try to alter the shape of your headset.
Do not expose your headset to liquid or moisture.
Do not expose your headset to extreme temperatures. Temperature range: 0-40C.
Do not expose your headset to fire or open flames.
Do not try to disassemble your headset. Service and Maintenance can only be
performed by BLUETREK® dealers.
-
-
Keep your headset away from dust and dirt.
Do not let children play with your headset, since it contains small parts that could
become detached and create a choking hazard.
-
-
Check the regulation in your area if you plan to use your headset while driving.
Turn off your headset before boarding an airplane.
CAUTION : Danger of explosion if battery is incorrectly replaced. Dispose of batteries
according to local regulations. Do not dispose as household waste.
PAGE 9 / 9
|