Radio / Cassette
Santiago CR 87
Operating instructions
Features
•
Radio Features
- 15 FM/5 AM Presets, Including 5 FM and 5 AM Travelstore Presets
- Station Scan
- Local/Distant Seek and Manual Tuning
•
Cassette Tape Player Features
- Auto-Reverse Cassette Mechanism
- True Fast-Forward/Rewind
- Radio Monitor
- Dolby B NR
•
Audio Features:
- 20 Watts x 4 Channel Integrated Amplifier
- 2-Channel Preamp Output
- Adjustable Maximum Turn-On Volume
- Bass, Treble, Balance and Fader Control
- Loudness Button
- Mute Button
- Auxiliary Input
•
Other Features:
- Detachable Face (Release Panel)
- Illumination, Amber
- Clock Recall
- 179 x 50 x 150 mm DIN/ISO Chassis
- Detachable Wire Harness
- Snap-In DIN Sleeve and Mounting Hardware
Your unit’s detachable front faceplate makes the unit useless to would-be thieves.
Designed, Engineered and Manufactured By Blaupunkt.
Traffic Safety and Precautions
•
•
Do not adjust your unit in difficult driving conditions that demand your full attention.
As the driver of a motor vehicle, it is your responsibility to pay attention to the traffic situation
at all times. Never use your unit in a way that could distract you.
•
•
Always make sure that you are still able to hear any warning signals coming from outside of
the vehicle, such as police or fire engine sirens, so that you can react accordingly.
If your vehicle was parked in direct sunlight resulting in a considerable rise in temperature
inside the vehicle, allow the unit to cool off before operating it.
19
Detachable Face (Release Panel)
Detaching and Attaching the Face:
The face of this unit can be detached and taken with you to prevent it from being stolen.
Detaching the Face:
Press the REL (Release) Button and detach the face by gently pulling it off as illustrated.
Note: Do not pull it straight out from the chassis. Be sure not to drop the face when detaching it
from the chassis. Do not expose the face to direct sunlight, heat sources such as hot air ducts or
leave it in a humid place.
Attaching the Face:
Apply the right hand side of the face to the chassis by sliding (part B) of the face to (part A) at
the front of the chassis. Gently push the left side of the face against the front of the chassis until
it snaps into place.
Note: Do not press against the display window. Do not press hard against the face when
attaching it to the chassis, it may be easily attached with gentle pressure.
Affixing Faceplate For Retail Display:
The faceplate can be affixed to the unit’s chassis, which is desirable for a retail display, for
example.
To affix the faceplate:
Insert the black bolt into the hole at the left front of the top of the radio. See * below.
*
A
B
20
Electrical Connections
To avoid the aggravation of costly mistakes and serious damage, please carefully read all of the
instructions before you begin. Carefully follow all instructions.
General Recommendations
•
If you’re not confident that you can install the unit correctly, have it installed by a qualified
Blaupunkt installation technician.
•
•
•
Use this unit only with negative ground 12 Volt (11-16 Volt) direct current (DC).
Be sure to detach the faceplate before you start to connect or install the unit.
We recommend making and testing all electrical connections before installing the unit.
Connect the leads (wires) according to instructions and diagram below.
Electrical Connection Instructions
1. Disconnect the vehicle battery’s negative terminal before making connections.
2. Connect the speakers following the guidelines in the “Speaker Connection” section below.
3. Connect the antenna output lead to the antenna motor trigger input terminal (if you have
one). The total amperage required of the antenna lead must not exceed 100 mA. Do not
connect the antenna lead to the antenna’s power supply input.
4. Connect the ground lead to a grounded metal part on the vehicle. We recommend
grounding all audio system ground leads (head unit, external amplifier, etc.) to a common
grounding point, preferably a non-painted surface under the instrument panel.
5. Connect the battery input lead to a source of constant battery power, preferably a terminal
to an appropriate slot in the fuse box.
6. Connect the ignition input lead only after the other leads are connected. Be sure to connect
the ignition lead to a positive (+) 12 Volt power terminal that is energized only when the
ignition key is set to the on position or accessory position.
7. Cover the ends of any unused leads with electrical tape. This will prevent them from
touching the vehicle or each other and causing a short-circuit and damage to the radio or
vehicle.
8. Reconnect the vehicle’s battery.
9. Verify that no fuses have blown.
10. Plug the harness into the unit.
Electrical Connections
Ignition
+12V
Antenna
Ground –
+12V
Battery
21
Speaker Connections
Speaker Connections
R
L
LF
F
R
R
R
+
-
+
-
+
-
+
-
RF
LF
RR
LR
Attach the faceplate and test the unit.
Once the connections have been successfully made, you can begin to mount the unit.
22
Installation
Recommendations
•
The illustration below shows a typical installation, however, you may need to adjust the
installation, depending on the unit. If you have questions or need additional installation
hardware, consult your Blaupunkt dealer.
•
Make sure the unit is firmly anchored and does not vibrate.
Mounting Hardware
Release Keys
Sleeve
Mounting The Unit in Most Dashboards
1. Install the Sleeve in the dashboard.
2. Select and bend the appropriate tabs to hold the sleeve firmly in place.
Bend these tabs
23
Mounting the Unit in a Japanese Car
You may have difficulty mounting this unit in some Japanese cars that have ISO mounting
features. In this case, consult your Blaupunkt dealer.
1. Run a blade along the slits on the back of the front trim ring, unscrew the two side screws,
and separate it from the unit. Save the trim ring and related hardware in case you ever want
to install the unit in another vehicle.
2. Use the vehicle’s own mounting hardware to attach the unit.
2 TOYOTA
1
max. size M5x8
Slit
to dashboard/center console
max. size
M5x8
Bracket
Support
2 NISSAN
max. size M5x8
to dashboard/center console
max. size
M5x8
Bracket
Support
24
Maintenance
Removing the Unit
Use the Release Keys as shown below. Keep them in a safe place in case you need them in the
future.
Fuse Replacement
When replacing the fuse, be sure to use one with the correct amperage, which will be stated on
the fuse case. Never use a fuse that has a stated amperage exceeding the one supplied for this
unit, as this could cause malfunction and serious damage to the unit.
25
Location of Controls
1
2
3
4
5
REL (Release) – Detaching Faceplate
ON (Power)
– Power On/Off
– Source and Radio Band Select
– Cassette Eject
– Mute
SRC
AUDIO
SCA
TS
– Audio
6
7
– Scan
– Travelstore
LD
– Loudness
SENS
– Tuning Sensitivity
8
9
Cassette Insertion Slot
CLK
– Clock Recall
DISP
– Display Change
10/11 PROG
– Tape Program Change (reverse)
– Fast Rewind
10
11
12
13
14
15
16
17
18
FR
FF
+
– Fast Forward
– Volume + / Bass + / Treble + / Balance Left / Fade to Front
– Volume - / Bass - / Treble - / Balance Right / Fade to Rear
– Seek and Manual Tuning / Clock Hours
– Seek and Manual Tuning / Clock Minutes
– FM/AM Presets
–
1, 2, 3, 4, 5
Display
– Dolby B NR (Noise Reduction)
26
Instructions – General Operation
See Traffic Safety and Precautions on page 19.
“Press” means a momentary press of less than 1/2 second. All presses requiring more than 1/2
second are followed by beep.
“Time Out” When additional button presses are anticipated to complete a procedure, the unit will
automatically exit the procedure after 4 seconds of inactivity.
Clock Recall
Vehicle ignition must be on. The display switches to clock.
Release for Detachable Faceplate
Push REL to detach face. Already inserted cassette remains in unit. Current settings and source
mode are stored. If power was not switched off before face removed, unit will automatically
power-on when face is reattached.
Power On
When ignition on, press ON or insert a disc to turn unit on. Last-used source becomes active,
unless unit is turned on by inserting tape, in which case tape player becomes active.
Power Off
Press ON for more than 1/2 second to turn the unit off. Unit stores current settings for source,
station or track, etc.
Setting the Clock
Turn the unit on. Press the CLK Button for four seconds until the clock starts blinking. (The
display will change after two seconds. Ignore this and continue to hold for two more seconds.)
Once the clock starts blinking, Press the to set the hour, and press the Button to set the
minutes. Press the CLK Button again to activate the clock.
Changing the Information Displayed
You can temporarily change the information shown in your unit’s display. You can also select
which information has “display priority” and is shown in the display except for moments when
adjustments are made.
•
To change the display priority, press the DISP Button for two seconds. The display priority
changes. The display priority choices are clock or radio frequency/“TAPE”.
•
To change the display temporarily, press and release the DISP Button to access the desired
information. After four seconds, the display changes back to the priority information.
Source
Use SRC to select source - AMT, FM1, FM2, FMT, cassete (if already inserted) or external unit
(“InP” display).
27
Audio Operation
Volume Control Buttons
Press + and – to increase/decrease volume from 0 to 63.
Adjustable Maximum Turn-On Volume
Press and hold the ON Button for more than two seconds. The unit turns off and the turn-on
volume level is memorized.
Mute
Press
to temporarily reduce volume. “MUTE” appears. Mute is terminated by pressing any
button.
Bass, treble, balance and fader
•
Bass
Hould down the AUDIO Button until “BASS” appears and then press immediately + or – to
increase or decrease bass in intervals between 7 and -7.
•
Treble
Hold down the AUDIO Button until “BASS” appears. Then press AUDIO once again so that
“TREb” appears. Now press immediately + or – to increase or decrease treble in intervals
between 7 and -7.
•
•
Balance
Hold down the AUDIO Button until “BASS” appears. Then press AUDIO twice so that “BAL”
appears. Now press immediately + or – to adjust the left/right volume between 9 (left) and -9
(right).
Fader
Hold down the AUDIO Button until “BASS” appears. Then press AUDIO three times so that
“FADE” appears. Now press immediately + or - to adjust the front/rear volume between 9
(front) and -9 (rear).
Loudness
Press LD to increase sound of low and high frequencies. “LOUD” icon appears. To cancel,
press LD again.
28
Radio Operation
Selecting Bands
Press SRC as needed to access FM1, FM2, FM3/FMT, AM/AMT banks.
Tuning Sensitivity
Press SENS for more that 2 seconds to switch between lo and dx search sensitivity. In general,
set SENS to “lo” when in metropolitan areas or where stations tend to be strong and local, and
to “dx” if in rural areas or where stations tend to be weak and distant.
Seek Tuning
Press or to seek next receivable frequency. Tuning stops at frequency that fulfills sensitivity
requirements predetermined.
Manual Tuning
To activate manual tuning press and hold or until you hear a beep. Press or again and
the frequency will go one channel/step in the direction pressed. Press and hold causes
continuous manual tuning. The manual tuning mode has to be reactivated after 4 seconds or
after storing a station on a preset.
Preset Station Storage
After tuning to the desired radio station on the desired band, press and hold a Preset Button for
more than 2 seconds to store the current frequency. Audio is muted during the storage, the
preset number appears, and a beep acknowledges the storage. The number of the selected
preset appears in the display.
Preset Station Selection
Press desired Preset Button.
Travelstore
In any FM Bank, press TS for 2 seconds to activate FM Travelstore. (In AM Bank, press it for 2
seconds to activate AM Travel Store.) “TS” appears. Beginning at the bottom of the band, TS
stores five relatively strong stations and returns to preset 1.
Station Scan Tuning
Press SCA. Frequency blinks during scanning. Unit stops at receivable stations for 4 seconds.
Unit continuously scans until user stops scan by pressing SCA.
Radio Reception Hint
When listening to weak or distant AM stations, adjusting the Treble to minimum (-7) will reduce
noise and improve sound.
Stereo Symbol
Stereo symbol “ ” turns on if a stereo station with a sufficiently strong signal is received. The
unit gradually switches between mono to stereo automatically.
29
Cassette Tape Player Operation
Tape Playback:
•
Insert cassette into Cassette Door. (Note: Make sure that the side of the cassette exposed is
facing right.)
•
If ignition switch is already in “on” or accessory position, insertion of cassette will turn unit
on. If unit already turned on, cassette insertion will override other audio source, such as
radio. “LOAd” appears for 2 seconds. Cassette play will begin, and the display will indicate
which tape program is in use, “1” or “2”.
•
The tape will continue to play until ejected, SRC button pressed, or unit turned off.
Ejecting The Tape
Press the button completely towards the face of the unit. The tape will eject. If uit is turned on,
“EJ” will appear in the display for 2 seconds and the last-heard radio station will play.
Tape Program Change
•
•
•
Automatic Change (Autoreverse): When the end of the tape is reached, the unit will
automatically reverse direction and play the other side of the tape.
Manual Change: To manually reverse tape direction, press both PROG (program) Buttons
(FR and FF) at the same time.
The change in direction and in tape program will be confirmed in the display (“1” or “2”).
Fast Winding
•
•
To Fast-Rewind the tape, press the FR Button. Tape rewinds and blinks in the display.
To Fast-Forward the tape, press the FF Button. Tape fast-forwards and
display.
blinks in the
•
To stop fast-winding, press the other fast winding button, FR or FF.
Radio Monitor
During tape winding, the radio will play the most-recently heard radio frequency. All frequencies
stored on the current bank of preset stations are accessible during fast winding.
Dolby B NR*
With this unit you can play back tapes recorded with Dolby B NR or without noise reduction.
Cassette tapes recorded with Dolby B NR stand out by their reduced tape hiss and the improved
dynamics. If Dolby B NR is switched on, “ ” will light up in the display. To switch on/off: Press
the
button.
*
Noise Reduction system manufactured under license from Dolby Laboratories Licensing Corporation.
Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
30
Auxiliary Input Jack
(cable connection with ø 3.5 mm pigtail coupler)
Connect other audio equipment, such as a portable CD or DAT player, through a 3.5 mm pigtail
connector. Press SRC until “InP” appears. Adjust volume, bass, and treble settings through the
head unit.
31
Troubleshooting Guide
General
Trouble
Cause/Solution
No sound.
• Adjust the volume with the + button.
• With a two-speaker system set the fader control to the
center position.
Radio reception
Trouble
Cause/Solution*
Preset stations are not receivable.
• The broadcast is too weak.
Automatic tuning is not possible.
• The broadcast is too weak. —> Use manual tuning.
• Not enough broadcast frequencies are receivable.
Travel Store feature does not complete
storing of five stations.
* Also make sure that antenna is connected and extended.
If the above mentioned solutions do not help to improve the situation, consult your nearest Blaupunkt
dealer.
Blaupunkt Telephone Hotline
Address of the next service centre in your vicinity
(only for Germany)
If you would like to know the address of the next Blaupunkt service centre of your area
without having our service list at hand:
-
-
-
Find out your area code.
Then call the following chargeable phone number: 01 80 / 5 25 56 66.
Using the area code to be entered you will be automatically given the address and
phone number of the next Blaupunkt service centre. You can also request this informa-
tion by fax.
32
Specifications
Audio Power Specifications
Power Output and Total Harmonic Distortion: 13 watts per channel minimum continuous
average output into 4 ohms, 4 channels driven, from 35-15000 Hz.
Other Specifications
Tuner
FM
Tuning Range:
87.5 - 108 MHz
1.0 µV
65 dB (stereo), 70 dB (mono)
35-15000 Hz
FM Mono Sensitivity:
Signal-to-Noise Ratio:
Frequency Response:
AM
Tuning Range:
Signal-to-Noise Ratio:
Frequency Response:
531 - 1602 kHz
50 dB
35-5000 Hz
Cassette
Signal-to-Noise Ratio:
Dolby B NR:
55 dB
65 dB
Tape Wow and Flutter:
Tape Frequency Response:
0.3 %
35-15000 Hz
Audio
Speaker Impedance:
Maximum Amp Power:
RMS Power:
4-8 ohms
4 x 20 watts (at 4 ohms)
4 x 13 watts (at 4 ohms)
acc. to DIN 45 325 at 14.4 volts
± 10 dB at 100 Hz
± 10 dB at 10 kHz
+ 8 dB at 60 Hz
Bass Control:
Treble Control:
Loud:
+ 2 dB at 8 kHz
General
Dimensions (w/o projecting parts/controls):
Mass:
179 x 50 x 150 mm
Approx. 1.4 kg
Power Requirement (neg. grnd.):
Operating Temperature:
Supplied Accessories:
12 V DC car battery (11-16 V DC allowable)
-20°C to 60°C
• Unit
• Faceplate (Release Panel)
• Wire Harness
• DIN Sleeve
• Mounting Hardware
• Owner’s Manual
• Car Radio Passport
• Labels
Design and specifications subject to change without notice.
33
Blaupunkt-Werke GmbH
Bosch Gruppe
02/97
18
K7/VKD 8 622 400 896
|