WP010B ManualENSP 031008.qxp 3/10/2008 2:38 PM Page 4
Minimum Gage for Cord Sets
Volts
Total Length of Cord in Feet
120V
0-25
26-50
51-100
(15,2-30,4m)
101-150
(30,4-45,7m)
(0-7,6m) (7,6-15,2m)
240V
0-50
51-100
101-200
201-300
(60,9-91,4m)
(0-15,2m) (15,2-30,4m) (30,4-60,9m)
Ampere Rating
More
Than
Not more
American Wire Gage
10" RANDOM
ORBITALWAXER
INSTRUCTION MANUAL
Than
6
0
6
-
-
18
18
16
14
16
16
16
12
16
14
14
14
12
12
10
10 -
12 -
12
16
Not Recommended
WARNING: This product or its power cord contains lead, a chemical known to the State of California to cause cancer and birth
defect or other reproductive harm. Wash hands after handling.
WARNING: RISK OF ELECTRICAL SHOCK:
Hold tool by insulated gripping surface when performing an operation where the tool may contact hidden wiring or its own cord.
Contact with “live” wire will make exposed metal parts of the tool “live” and shock the operator.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• THIS UNIT IS NOT FOR USE BY CHILDREN AND SHOULD ONLY BE OPERATED BY ADULTS.
• Do not immerse unit in water.
• Do not drop or throw unit.
• Pull cord by plug rather than cord when disconnecting the unit from power source.
• Power Switch should be in the OFF position when the unit is not in use. Make sure switch is in the OFF position before connection to
a power source.
• Do not crush, cut, pull or expose cord to extreme heat.
• Position cords so they do not become entangled or become a safety hazard. Keep cords away from sharp edges.
• Use in a dry location only.
• Do not open body casing. There are no user-serviceable parts inside. Opening the body casing will void manufacturer’s warranty.
• Do not use any accessory that is not recommended or provided by the manufacturer.
• To avoid possible damage that may shorten the unit’s working life, protect it from direct sunlight, direct heat and/or moisture.
• Do not allow power cord to contact the rotating bonnet.
Catalog Number WP010B
Thank you for choosing Black & Decker!
to register your new product
• Allowing dust to get into mouth, eyes, or lay on skin may promote absorption of harmful chemicals.
ADDITIONAL SPECIFIC SAFETY INSTRUCTIONS
• Clean your tool out periodically.
WARNING: Always wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some
conditions and duration of use, noise from this product may contribute to hearing loss.
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting
operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-544-6986
BEFORE YOU CALL, HAVE THE CATALOG No, AND DATE CODE AVAILABLE. IN MOST CASES,
A BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF
YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL.YOUR FEEDBACK IS VITAL TO
BLACK & DECKER.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals:
work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Cat. # WP010B
March 2008
Form # 90527869
Copyright © 2008 Black & Decker
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective
clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.
Printed in China
SAFETY GUIDELINES / DEFINITIONS
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury.
Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.
CAUTION: Wear appropriate hearing protection during use. Under some conditions and duration of use, noise from this product may
contribute to hearing loss.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage.
WARNING: RISK OF PERSONAL INJURY:
• Use only accessories rated at least 3000/min.
RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of
personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage.
There are certain applications for which tools and equipment are designed. Black & Decker strongly recommends that this product NOT be
modified and/or used for any application other than for which it was designed. Read and understand all warnings and operating instructions
before using any tool or equipment.
• DO NOT use string tie (or drawstring) polishing pads or bonnets with this unit. Extreme personal injury may result if fingers are
caught by rotating string tie. USE ONLY bonnets with elastic bands.
• Failure to properly seat the Bonnet to the pad may result in the Bonnet being thrown from the pad.
• Always maintain a firm grip on the Waxer/Polisher handle(s) to prevent loss of control.
The label on your tool may contain the following symbols:
WARNING: RISK OF PERSONAL INJURY OR PROPERTY DAMAGE:
• Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use
NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE WHEN USING THIS WAXER/POLISHER:
• Use clamps or another practical way to secure and support the work piece to a stable platform. Holding the work by hand or against
your body is unstable and may lead to loss of control.
• Do not use tool if Power Switch does not turn it ON or OFF. Any tool that cannot be controlled with the power switch is dangerous
and must be repaired.
• Operate this waxer/polisher ONLY on AC current on which the voltage is within correct limits (110/120 volts). Never attempt to
operate on DC current. To do so may seriously damage the waxer/polisher.
• Always disconnect the unit’s cord plug from power source before making any adjustments, changing bonnets or storing the tool to
reduce the risk of accidentally starting the waxer/polisher.
• Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the waxer/polisher’s
operation. If damaged, have the tool serviced before using.
• Use only accessories that are supplied or recommended by the manufacturer for this model. Refer to the “Accessories” section of
this Instruction Manual for more information.
• NEVER allow Gasoline, Brake Fluids or any petroleum-based products to come in contact with plastic parts or power cord. They
contain chemicals that can damage, weaken or destroy plastic and insulation.
• Read And Understand This Instruction Manual Before Using This Unit.
SAVE THESE INSTRUCTIONS
INTRODUCTION
Thank you for choosing the Black and Decker® 10" Random Orbital Waxer. This lightweight and easy to use waxer/polisher imitates a
hand polishing motion leaving an even finish with no hot spots, streaks or swirls. The random orbital movement of the polisher
oscillates as it rotates, so it is ideal for delivering a shine that ordinarily takes hours to produce by hand. Please read this guide
carefully before use to ensure optimum performance and avoid damage to the unit or items that you are using it with.
IMPORTANT SAFETY INSTRUCTIONS
GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL TOOLS
READ ALL INSTRUCTIONS
FEATURES
WARNING: Read all instructions before operating product. Failure to follow all instructions listed below may result in electric
• Powerful, high performance, quiet running motor
• Three polishing bonnets included (Wax Applicator, Wax Off and Polishing)
• Ergonomic handgrip design provides comfortable two-handed use
• Ideal for buffing cars, boats, trucks, SUVs and recreational vehicles
• Safe for all finishes, lightweight and easy to use
shock, fire and/or serious injury.
Polarized Plugs
Polarized plugs (one blade is wider than the other) are used on equipment to reduce the risk of electric shock. When provided, this
plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
Controls and Features
• AVOID DANGEROUS ENVIRONMENTS: Don’t use tools in damp or wet locations. Don’t use tools in the rain.
• KEEP CHILDREN AWAY. All visitors should be kept at a distance from work area.
• STORE IDLE TOOLS INDOORS. When not in use, tools should be stored indoors in dry, and high or locked-up place – out of reach of
children.
ON/OFF POWER SWITCH
• DON’T FORCE TOOL. It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.
• USE RIGHT TOOL. Do not use the tool for any job except that for which it is intended.
• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and substantial, non-
skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.
• USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT. Use safety goggles or safety glasses with side shields, complying with
applicable safety standards and, when needed, a face shield. Also use face or dust mask if operation is dusty. This applies to all persons
in the work area. Also use a hard hat, hearing protection, gloves, safety shoes and dust collection systems when specified or required.
Safety glasses or the like are available at extra cost at your local dealer or Black & Decker Service Center.
• DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges.
• SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to operate tool.
• DON’T OVERREACH. Keep proper footing and balance at all times.
• DISCONNECT TOOLS. Disconnect the tool from the power supply when not in use, before servicing, and when changing accessories
such as bonnets and the like.
POLISHING BONNET
(FOAM PADDED SMOOTH
CLOTH)
• AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is off when plugging in.
• GROUND FAULT CIRCUIT INTERRUPTER (GFCI) protection should be provided on the circuits or outlets to be used. Receptacles are
available having built in GFCI protection and may be used for this measure of safety.
• USE OF ACCESSORIES AND ATTACHMENTS. The use of any accessory or attachment not recommended for use with this tool could
be hazardous.
Note: Refer to the accessory section of this manual for further details.
WAX OFF BONNET
(DOUBLE-SIDED TERRY
CLOTH)
• STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are tired.
• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to
determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be
properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have
defective switches replaced by authorized service center. Do not use tool if switch does not turn it ON and OFF.
• DO NOT OPERATE portable electric tools near flammable liquids or in gaseous or explosive atmospheres. Motors in these tools
normally spark, and the sparks might ignite fumes.
WAX APPLICATOR
BONNET (TERRY CLOTH
WITH PLASTIC LINER)
• OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked.
• EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power
and overheating. The accompanying table shows the correct size to use depending on cord length and nameplate ampere rating. If in
doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
GENERAL USAGE GUIDE
It is very important that your car be clean and dry before applying wax. Any wax protection will wear longer and protect better if
applied directly to the paint.
A good quality liquid wax is recommended because of its ease of application, but a paste wax will also work with a little more effort.
Hard paste wax, however, should be applied by hand, then removed using this unit.
Always use the bonnet recommended for each step (directions follow) to achieve the best results.
Any areas inaccessible to the waxer/polisher should be waxed and finished by hand.
CAUTION: TO AVOID THE RISK OF PERSONAL INJURY OR PROPERTY DAMAGE:
• MAKE SURE THE POLISHER IS IN THE OFF POSITION BEFORE PLUGGING THE POLISHER INTO AN APPROPRIATE POWER
OUTLET.
• Place the power cord over your shoulder to avoid contact with the polisher head or the surface while the unit is running.
4
1
|