April 2005
AC1030A
2-Channel
Component Video Splitter/Switch
AC1030A
Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
CUSTOMER
SUPPORT
INFORMATION
Web site: www.blackbox.com
•
E-mail: [email protected]
Model AC1030A
FEDERAL COMMUNICATIONS COMMISSION
AND CANADIAN DEPARTMENT OF COMMUNICATIONS
RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio frequency energy
and if not installed and used properly, that is, in strict accordance with
the manufacturer’s instructions, may cause interference to radio
communication. It has been tested and found to comply with the limits
for a Class A computing device in accordance with the specifications in
Subpart B of Part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when the equipment is
operated in a commercial environment. Operation of this equipment in
a residential area is likely to cause interference, in which case the user
at his own expense will be required to take whatever measures may be
necessary to correct the interference.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
This digital apparatus does not exceed the Class A limits for radio
noise emission from digital apparatus set out in the Radio Interference
Regulation of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la classe
A prescrites dans le Règlement sur le brouillage radioélectrique publié
par le ministère des Communications du Canada.
EUROPEAN UNION DECLARATION OF CONFORMITY
This product complies with the requirements of the European EMC
directive 89/336/EEC
2
2-Channel Component Video Splitter/Switch
Normas Oficiales Mexicanas (NOM)
Electrical Safety Statement
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el
aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia
futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación
deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la
tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean
recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo
descrito en las instrucciones de operación. Todo otro servicio deberá ser referido a
personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su
uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra o superficie
similar puede bloquea la ventilación, no se debe colocar en libreros o gabinetes que
impidan el flujo de aire por los orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como
radiadores, registros de calor, estufas u otros aparatos (incluyendo amplificadores)
que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo
descrito en el instructivo de operación, o como se indique en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del
equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean
pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo
particular atención a los contactos y receptáculos donde salen del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones
del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de
energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por
un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados
sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
3
Model AC1030A
Contents
1. Introduction ..............................................................................page 5
1.1 General ................................................................................page 5
1.2 Features ...............................................................................page 6
2. Installation .................................................................................page 7
3. Operation...................................................................................page 8
4. Troubleshooting.........................................................................page 9
4.1 FAQ......................................................................................page 9
4.2 Calling Black Box................................................................page 9
4.3 Shipping & Packaging..........................................................page 9
5. Specifications...........................................................................page 10
4
2-Channel Component Video Splitter/Switch
1. Introduction
1.1 General
The Model AC1030A is a versatile dual-purpose unit that can function
as either a Video Splitter (1 in x 2 out) or a Switcher (2 in x 1 out). Its
mode of operation is set via a convenient front panel switch. The device
is compatible with analog Component Video (YCbCr, or YPbPr) and
RGB (sync-on-green) signals. It supports all RGB, TV, and HDTV
resolutions up to 1080i.
Figure 1 – Rear and Front of the AC1030A
The AC1030A features 3 BNC connectors per channel and comes with
RCA-to-BNC adapters for all connections allowing the use of either 3-
BNC or 3-RCA cables.
Figure 2 – BNC to RCA Adapters
5
Model AC1030A
1.2 Features
•
•
•
•
•
•
•
•
Dual-purpose unit; can work as a splitter or as a switch
Perfect for high quality video
Supports all resolutions including 720p and 1080i
LED Indicators
Compact and Economical
Installs in minutes
Includes BNC-to-RCA adapters to allow use of either cable
Universal Power Supply
6
2-Channel Component Video Splitter/Switch
2. Installation
1. Your package includes the Splitter/Switch box, a power supply, 9
pieces of RCA-to-BNC adapters, and this Manual. No cables are
included with this device, if you need to purchase Component
cables for inputs and outputs please contact Black Box.
2. Prior to applying the power supply to the unit, decide if the
application calls for a Splitter (1 in x 2 out) or a Switch (2 in x 1
out) and set the mode of operation via the front panel switch. Once
power is applied, if the unit is acting as a splitter both LED’s on the
front panel (labeled A and B) will be on, and when acting as a
switch, only one LED (the selected port) will be lit.
Figure 3- Front Panel
3. Plug the input and output cables to the unit
4. Plug the power supply into the unit.
5. Turn on the monitor(s) and the video source.
Figure 4 – Rear Panel
7
Model AC1030A
3. Operation
When the AC1030A is configured as a Splitter, both LED’s on the front
panel (labeled A and B) will be lit and the push-button switches are
disabled.
Alternatively, if the unit is acting as a Switch, only on of the LED’s on
the front panel will be lit. Use the push-buttons on the front panel to
select the input channel to be routed to the output. By default, upon
power-on reset, channel 1 is selected.
Note that the unit can also be used for Composite Video signals, which
only require one connection for each port. In this case, we recommend
that you use the Y connector on each port.
8
2-Channel Component Video Splitter/Switch
4. Troubleshooting
4.1 FAQ
No Sync or Color Distortion
Most common problem can be attributed to incorrect cable
connection to the unit. The Component video and RGB signals
have 3 components each. This means that each port has 3
connections and their proper usage is imperative. In general use
the following guidelines:
G or Y à green cable
B or Pb à blue cable
R or Pr à red cable
4.2 Calling Black Box
If you determine that your unit is malfunctioning, do not attempt to
repair the unit. Contact Black Box Tech. Support at 724-746-5500.
Before you do, make a record of the history of the problem. We will be
able to provide more efficient and accurate assistance if you have a
complete description, including:
• The nature and duration of the problem;
• The components involved in the problem—that is, what type of
cable, makes and models of computers and monitors, etc.
• The results of any testing you’ve already done.
4.3 Shipping and Packaging
If you need to transport or ship your Splitter:
• Package it carefully. We recommend that you use the original
container.
• Before you ship the unit back to Black Box for repair or return,
contact us to get a Return Authorization (RA) number.
9
Model AC1030A
5. Specifications
Analog Component Video YPbPr or YCbCr and RGB
signals with sync-on-green.
Standards
Resolutions
All Standard TV, HDTV and PC resolutions Including:
640 X 480, 720 X 480, 720 X 576, 800 X 600, 1024 X
768, 1280 X 720, 1280 X 768, 1280 X 1024, 1600 X
1200, 1920 X 1080
Temperature Operating: 32 to 122°F (0 to 50°C);
Storage: –40 to +185°F (–40 to +85°C)
Enclosure
MTBF
Steel
90,000 hours (calculated estimate)
Power
From utility-power (mains) outlet, through included
external power supply. Output Voltage: 6v DC Center-
Positive. Average Power Consumption: 1 Watt
Size (hxwxd) 1.38”H X 8.38”W X 3.00”D
Weight
1.2 lbs
10
2-Channel Component Video Splitter/Switch
11
© Copyright 2005. Black Box Corporation. All rights reserved.
1000 Park Drive Lawrence, PA 15055-1018 724-746-5500
Fax 724-746-0746
|