Automatic
washing machine
WME 7267 W
WME 7267 S
TABLE OF CONTENTS
Programme selection and consumption
table . . . . . . . . . . . . . . . . . . . . . . . . . 18
Auxiliary functions . . . . . . . . . . . . . . . 19
Time screen. . . . . . . . . . . . . . . . . . . . 19
Starting the programme. . . . . . . . . . . 20
Progress of programme. . . . . . . . . . . 20
Changing the selections after the
programme has started . . . . . . . . . . . 21
Child-proof lock. . . . . . . . . . . . . . . . . 21
Ending the programme through
1 Your Washing Machine
4
Overview . . . . . . . . . . . . . . . . . . . . . . . 4
Specifications . . . . . . . . . . . . . . . . . . . 5
2 Warnings
6
General Safety. . . . . . . . . . . . . . . . . . . 6
First Use . . . . . . . . . . . . . . . . . . . . . . . 6
Intended use . . . . . . . . . . . . . . . . . . . . 6
Safety instructions . . . . . . . . . . . . . . . . 7
If there are children in your house... . . . 7
cancelling . . . . . . . . . . . . . . . . . . . . . 22
Programme in rinse hold mode . . . . . 22
End of programme . . . . . . . . . . . . . . 22
3 Installation
8
Removing packaging reinforcement. . . 8
Opening the transportation locks. . . . . 8
Appropriate installation location . . . . . . 8
Adjusting the feet. . . . . . . . . . . . . . . . . 8
Connecting to the water supply. . . . . . 9
Connecting to the drain . . . . . . . . . . . . 9
Electrical connection . . . . . . . . . . . . . 10
Destroying the packaging material. . . 10
Disposing of the old machine. . . . . . . 10
6 Quick instructions for
daily use
23
25
7 Cleaning and care
Detergent drawer. . . . . . . . . . . . . . . . 25
The door and the drum . . . . . . . . . . . 25
Outer cabinet and control panel. . . . . 25
Inlet water filters. . . . . . . . . . . . . . . . . 25
Draining any remaining water and
4 Initial preparations for
cleaning the pump filter . . . . . . . . . . . 26
washing
11
8 Solution suggestions for
problems
Sorting the laundry . . . . . . . . . . . . . . 11
Preparing clothes for washing . . . . . . 11
Correct load capacity . . . . . . . . . . . . 11
Loading door. . . . . . . . . . . . . . . . . . . 12
Detergents and softeners . . . . . . . . . 12
28
34
35
9 Guarantee
10 Service
5 Selecting a programme and
operating your machine
14
Control panel. . . . . . . . . . . . . . . . . . . 14
Display symbols. . . . . . . . . . . . . . . . . 15
Turning the machine on. . . . . . . . . . . 15
Programme selection. . . . . . . . . . . . . 15
Additional programmes . . . . . . . . . . 16
Special programs . . . . . . . . . . . . . . . 16
Temperature selection. . . . . . . . . . . . 17
Spin Speed selection. . . . . . . . . . . . . 17
EN
3
1 Your Washing Machine
Overview
3
4
1
2
5
6
1 - Detergent Drawer
2 - Door
4 - Control Panel
5 - Filter Cap
3 - Top Lid
6 - Height-adjustable feet
EN
4
Specifications
Models
WME7267S
WME7267W
Maximum dry laundry capacity (kg)
Height (cm)
7
7
84
84
Width (cm)
60
54
60
54
Depth (cm)
Net Weight (kg)
Electricity (V/Hz.)
Total Current (A)
Total Power (W)
Spinning cycle (rpm max.)
74
74
230 V / 50Hz
10
230 V / 50Hz
10
2200
1600
2200
1600
Specifications of this appliance may change without notice to improve the quality of
the product. Figures in this manual are schematic and may not match your product
exactly.
Values stated on the machine labels or in the documentation accompanying it are
obtained in laboratory in accordance with the relevant standards. Depending on
operational and environmental conditions of the appliance, values may vary.
EN
5
2 Warnings
Please read the following information.
Otherwise, there may be the risk of
personal injury or material damage.
Moreover, any warranty and reliability
commitment will become void.
may be caused by the software.
Press “Start/Pause/Cancel” button
for 3 seconds to cancel the program
set in your machine before calling
the authorized service.
General Safety
First Use
•
Never place your machine on a
carpet covered floor. Otherwise,
lack of airflow from below your
machine may cause electrical
parts to overheat. This may cause
problems with your washing
machine.
•
To prepare your machine for
washing, carry out your first washing
process without loading your
machine and with detergent under
“Cottons 90°C” program.
•
•
•
Ensure that the cold water
connections has been made
correctly when installing your
machine.
•
•
If the power cable or mains plug is
damaged you must call Authorized
Service for repair.
Check water hoses for wear. Do
not use old/used water inlet hoses.
These may cause stains on your
laundry.
Fit the drain hose into the waste
water system securely to prevent
any water leakage and to allow
machine to take in and discharge
water as required. It is very
If the current fuse or circuit breaker
is less than 15 Amperes, please
have a qualified electrician install a
15 Ampere fuse or circuit breaker.
To make your machine ready for
use, please be sure that the tap
water supply and water drainage
systems are appropriate before
calling the authorized service. If they
are not, call a qualified plumber to
have any necessary arrangements
carried out.
•
important that the water intake
and drain hoses are not folded,
squeezed, or broken when the
appliance is pushed into place after
it is installed or cleaned.
Your washing machine is designed
to continue operating when the
power restores after a power
interruption. You cannot cancel any
program by pressing the “On/Off
button.” The machine will resume its
program when the power restores.
Press the “Start/Pause/Cancel”
button for 3 seconds to cancel
the program (See, Cancelling a
Program)
Intended use
•
This product has been designed for
home use.
The appliance may only be used for
washing and rinsing of textiles that
are marked accordingly.
•
•
•
•
Only detergents, softeners and
supplements suitable for washing
machines may be used.
Observe the care instructions
labelled on textile products and
any other instructions given by
companies that produce detergents
for your machine.
•
•
There may be some water in your
machine when you receive it. This is
from the quality control process and
is normal. It is not harmful to your
machine.
Safety instructions
•
This appliance must be connected
to an earthed outlet protected by a
fuse of suitable capacity.
Some problems you may encounter
EN
6
•
•
The supply and draining hoses must
always be securely fastened and
remain in an undamaged state.
Fit the draining hose to a washbasin
or waste system securely before
starting up your machine. There may
be a risk of being scalded due to
high washing temperatures!
Never open the door or remove the
filter while there is still water in the
drum. Otherwise, there may be the
risk of flooding and possible injury
due to the hot water.
Never force open the locked door!
The door will be ready to open just a
few minutes after the washing cycle
comes to an end.
Unplug the machine when it is not in
use.
Never wash down the appliance
with a water hose! There is the risk
of electric shock! Always disconnect
from the mains by unplugging before
cleaning.
Never touch the plug with wet
hands. Never unplug by pulling
on the cable, always pull out from
the plug only. Do not operate the
machine if the power cord or plug is
damaged.
Never attempt to repair the machine
yourself. Otherwise, you may be
putting yours and other’s lives in
danger.
For malfunctions that cannot
be solved by information in the
operating manual:
•
•
Store all detergents in a safe place
out of reach of the children.
Use Child/Keylock to prevent
children altering the settings
Electrical connection
Make sure that you have an earthed
power outlet socket rated at 13 amps
(minimum).
•
•
Attention!
If you place your machine under a
worktop, the socket must be reachable
after installation, or a separate switch
(which can disconnect the two poles)
must be used in the installation.
Connect the power cord to the
appropriate electrical socket with an
equivalent current rating indicated on the
rating plate at the front of the machine
behind the kick plate.
•
•
After removing the plug from its transit
position, please insert the plug seal
to prevent water spillage entering the
machine.
•
Electrical requirements
Before you insert the plug into the wall
socket make sure that the voltage and
the frequency shown in the rating label
corresponds to your electricity supply.
We recommend that this appliance be
connected to the mains supply via a
suitable switched and fused socket in a
readily accessible position.
•
•
Should the mains lead of the appliance
become damaged or need replacing
at any time, it must be replaced by a
special purpose made mains lead which
can only be obtained from a Authorised
Service Agent.
Turn off the machine, unplug it, turn
off the water tap and contact an
authorized service agent.
If there are children in your
house...
B This appliance must be earthed
If the fitted moulded plug is not suitable
for your socket, then the plug should be
cut off and an appropriate plug fitted.
Destroy the old plug, which is cut off as
a plug with a bared cord could cause a
shock hazard if inserted into a socket
elsewhere in the house.
•
Electrical appliances may be
dangerous for the children. Keep
children away from the machine
when it is operating. Do not let them
tamper with the machine.
•
Close the door when you leave the
area where the machine is located.
EN
7
The moulded plug on this appliance
incorporates a 13A fuse. Should the fuse
need to be replaced an ASTA approved
BS1362 fuse of the same rating must
be used. Do not forget to refit the fuse
cover. In the event of losing the fuse
cover, the plug must not be used until a
replacement fuse cover has been fitted.
Colour of the replacement fuse cover
must be the same colour as that visible
on the pin face of the plug. Fuse covers
are available from any good electrical
store.
Important
Fitting a different plug
As the colours of the wires in the
mains lead of this appliance may not
correspond with the coloured markings
identifying the terminals on your plug,
proceed as follows:
1
Connect the green - yellow or green
(earth) wire to the terminal in the
plug marked ‘E’ or with the symbol
f or coloured green and yellow or
green.
2
3
Connect the blue (neutral) wire to
the terminal in the plug marked ‘N’
or coloured black.
Connect the brown (live) wire to the
terminal in the plug marked ‘L’ or
coloured red.
With the alternative plugs a 13A fuse must
be fitted either in the plug or adaptor or in the
main fuse box. If in doubt contact a qualified
electrician.
EN
8
3 Installation
3. Fit the covers (supplied in the bag
with the Operation Manual) into the
holes on the rear panel. (“P”)
Removing packaging
reinforcement
Tilt the machine to remove the
packaging reinforcement. Remove the
packaging reinforcement by pulling the
ribbon.
C Keep the transportation safety
bolts in a safe place to reuse when
the washing machine needs to be
moved again in the future.
C Never move the appliance without
the transportation safety bolts
properly fixed in place!
Appropriate installation
location
Install the appliance in environments
which have no risk of freezing, in a
stable and level position.
C The floor must be capable of
carrying the load on it!
Opening the transportation
locks
C Transportation safety bolts must
be removed before operating the
washing machine! Otherwise, the
machine will be damaged!
C If the washing machine and a drier
are placed on top of each other,
their approximate weight together
may reach 180 kg when they are
full.
1. Loosen all the bolts with a spanner
Important:
until they rotate freely (“C”)
•
•
•
Do not place the appliance on top of
the power cable.
Keep at least 1cm distance from the
edges of other furniture.
Place the machine on a firm surface;
do not position it on a long pile rug
or such like surfaces.
2. Remove transportation safety bolts
by turning them gently.
Adjusting the feet
C Do not use any tools to loosen the
lock nuts. Otherwise, they can be
damaged.
1. Manually (by hand) loosen the lock
nuts on the feet.
2. Adjust them until the machine
stands level and firm.
3. Important: Tighten all lock nuts up
again.
EN
9
•
Open the taps completely after
making the hose connection to
check if there is any water leakage
at the connection points. Turn off
the tap and remove the nut in case
of any leakage. Retighten the nut
carefully after checking the seal.
To prevent any water leakage and
any other damage to be caused by
it, keep the taps closed when the
machine is not in use.
Connecting to the water
supply.
Important:
•
The water supply pressure required
to run the machine must be 1-10
bar (0,1 – 1 MPa). (Practically, it is
necessary to have 10 – 80 liters
of water flowing from the tap in
one minute to have your machine
run smoothly.) Attach a pressure-
reducing valve if the water pressure
is higher.
•
Models with a single water inlet
should not be connected to the
hot water tap. Laundry may be
damaged or the appliance may
switch to protection mode and not
work.
•
Connect the special hose supplied
with the machine to the water intake
valves on the machine.
When returning the appliance to its
place after maintenance or cleaning,
care should be taken not to fold,
squeeze or block the hoses.
Connecting to the drain
The water discharge hose can be
attached to the edge of a washbasin
or waste water system. The drain hose
should be firmly fitted into the drain as
to not loosen in its housing.
•
In order to prevent water leakage
that may occur at the connection
points, there are rubber seals (4
seals for the models with double
water inlet and 2 seals for other
models) attached to the hoses.
These seals should be used at the
tap and machine connection ends of
the hoses. The plain end of the hose
fitted with a filter must be attached
to the tap and the elbowed end
must be attached to the machine.
Tighten the nuts of the hose well by
hand; never use wrenches to tighten
the nuts.
Important:
•
The end of the drain hose can
be directly connected to the
wastewater drain or to the
washbasin. The fitting must be
secured in all types of connections.
Your house may be flooded if the
hose falls out of its housing during
water discharging.
•
The hose should be attached to a
height of at least 40 cm, and 100
cm at most.
EN
10
national regulations.
•
•
Power cord plug must be within
easy reach after installation.
The voltage and the allowed fuse
protection are specified in the
section “Technical Specifications”.
The specified voltage must be equal
to your mains voltage.
•
•
Connection via extension cords or
multi-plugs should not be made.
B A damaged power cable must be
replaced by a qualified electrician.
B A faulty appliance must not be
operated whilst faulty until it has
been repaired! There is the risk of
electric shock!
•
•
In case the hose is elevated
after laying it on the floor level or
close to the ground (less than
40 cm above the ground), water
discharge becomes more difficult
and the laundry may come out wet.
Therefore, the heights described in
the figure should be followed.
To prevent dirty water refilling the
machine, and to allow for easy
discharge, the end of the hose
must not be submerged in the drain
water. The end of the hose must be
able to take in air. The hose should
be pushed into the drainage for
more than 15 cm. If it is too long
you may have it shortened.
Destroying the packaging
material
Packaging material can be dangerous to
children. Keep the packaging materials
out of reach of children or dispose
them by classifying according to waste
directives. Do not dispose of them
together with normal domestic waste.
Packaging materials of your machine are
manufactured from recyclable materials.
•
•
The end of the hose should not be
bent, it should not be stepped on
and it must not be folded between
the drain and the machine.
Disposing of the old machine
Dispose of your old appliance in an
environmental friendly manner.
•
You may refer to your local agent or
solid waste collection center in your
municipality to learn how to dispose
of your machine.
The length of the hose is too short,
you may add an extension hose
to the original section. The length
of the hose must not be longer
than 3.2 m after coming out of the
machine. To avoid water leakage
failures, the connection between the
extension hose and the drain hose
of the product must be fitted well
with an appropriate clamp as not to
come off and leak.
Before disposing of your old washing
machine, cut off the mains plug and
make the door lock unusable.
Electrical connection
Connect the machine to an earthed
outlet protected by a fuse of suitable
capacity.
Important:
•
Connection should comply with
EN
11
4 Initial preparations for washing
•
Empty pockets and remove all
Sorting the laundry
foreign objects such as coins, pens
and paper clips. If possible, turn
pockets out and brush.
•
Sort the laundry according to type
of fabric, color, and degree of soiling
and permissible water temperature.
Always follow the advice on the
garment labels.
•
Place small items like infants’
socks and nylon stockings, etc.
in a laundry bag, pillow case or
something similar. This will also save
your laundry from getting lost.
Place curtains in the machine with
care. Remove curtain rails and
pullers.
•
Non machine
washable
Washing water
Wash with
temperature sensitive, short
programs.
Do not wash
•
•
Fasten zippers, sew loose buttons
and mend rips and tears.
Wash “machine washable” or “hand
washable” labelled products only
with an appropriate program.
Do not wash colours and whites
together. New, dark coloured
cottons may release a lot of dye.
Wash them separately.
Bleach can be Do not use
Dry-cleanable
Do not
dry-clean
used
bleach
•
•
•
Tough stains must be treated
properly before washing. If you are
not sure, check with a dry cleaner.
Use only dyes/colour changers and
lime removers suitable for machine
wash. Always follow the instructions
on the packaging.
Suitable for
drier
Do not dry
with drier
Dry
Dry on a
hanger
horizontally
Hang without Can be ironed
spinning
Can be
Do not iron
with hot iron ironed with
warm iron
•
•
Wash trousers and delicate clothes
turned inside out.
Keep laundry items made of Angora
wool in the freezer for a few hours
before washing. This will reduce
pilling.
Preparing clothes for washing
Laundry items with metal attachments
such as, bras, belt buckles and metal
buttons will damage the machine.
Remove metal attachments or place the
items in a clothing bag, pillow case, or
something similar.
Correct load capacity
•
The maximum load capacity
depends on the type of laundry, the
degree of soiling and the washing
program you wish to use.
C The machine adjusts the amount of
water according to the amount of
laundry placed inside.
C Please follow the information in the
"Program Selection Table". Washing
results will degrade when the
machine is overloaded.
EN
12
Following weights are given as
examples.
Detergent, softener and other
cleaning agents
Add detergent and softener before
starting the washing program.
Never open the detergent dispenser
drawer while the washing program is
running!
When using a program without pre-
wash, no detergent should be put
into the pre-wash compartment
(Compartment no. I).
A program without pre-wash should
be selected if a detergent bag or a
dispensing ball is going to be used.
You can place the detergent bag or
the dispensing ball directly among the
laundry in your machine.
Laundry type
Bathrobe
Napkin
Weight (gr.)
1200
100
700
500
200
250
200
200
100
600
200
500
100
Duvet cover
Bed Sheet
Pillowcase
Tablecloth
Towel
Evening gown
Underclothing
Men’s overalls
Men’s shirt
Men’s pyjamas
Blouse
Choosing the detergent type
The type of detergent to be used
depends on the type and colour of
fabric.
Loading door
The door is locked during program
operation. The door can be opened after
some time following the program end.
•
•
•
Use different detergents for coloured
and white clothes.
Wash woolens with a special
detergent specifically for woolens.
Use only detergents manufactured
specifically for automatic washing
machines.
•
•
Open the door.
Place laundry items loosely in the
machine.
•
Push the door until it clicks into
place tightly. Ensure that no items
are caught in the door.
Detergent quantity
Detergents and softeners
Detergent drawer
The amount of washing detergent to
be used depends on the amount of
laundry, the degree of soiling and water
hardness.
The detergent drawer is composed of
three compartments:
The detergent dispenser may be in two
different types according to the model of
your machine.
•
Do not use amounts exceeding
the quantities recommended on
the package to avoid problems
of excessive foam, poor rinsing,
financial savings and finally,
environmental protection.
- (I) for prewash
- (II) for main wash
- (III) siphon
– ( ) for softener
•
•
Use small amounts of detergent at a
suitable measure for small amounts
of laundry or for only slightly soiled
laundry.
Use exact measures for highly
concentrated detergents.
EN
13
follow the instructions on the
package.
Detergent
quantity
for prewashing
for main washing
1/2 measure
1 measure
an additional 1/2
measure
with hard water
Softener
Put the softener into the softener
compartment of the detergent
dispenser.
•
Use the proportions recommended
on the packet.
•
Never exceed the (> max <) level
marking; otherwise, the softener will
be wasted without being used.
If the softener has lost its fluidity,
dilute dense softener with water
before placing it in the detergent
drawer.
•
Liquid detergent
When using liquid or gel washing
detergents, please note the following:
•
•
The liquid detergent may leave
stains on your laundry if time delay
feature is selected.
Do not use liquid detergent if you
want to wash using the time delay
feature.
•
•
Do not use liquid detergent for the
main wash in a cycle with pre-wash.
Use the detergent manufacturer’s
measuring cup and follow the
instructions on the package.
Starch
•
Add liquid starch, powder starch
or the fabric dye into the softener
compartment as instructed on the
package.
•
•
Never use fabric softener and starch
together in the same washing cycle.
Wipe the inside of the drum after
using starch.
Eliminating lime formation
•
When required, use only appropriate
lime removers developed specifically
for washing machines and always
EN
14
5 Selecting a programme and operating your machine
Control panel
Figure 1
1
2
3
4
5
6
7
8
1 - Spin Speed Adjustment Button
2 - Display
3 - Temperature Adjustment Button
4 - Programme Selection Knob
5 - On / Off Button
6 - Time Delaying Button (+/-)
7 - Auxiliary Function Buttons
8 - Start/Pause/Cancel Button
EN
15
Display symbols
Figure 2
appear. Press “Start/Pause/Cancel”
button (Figure 1-8) to start the
programme.
Main programmes
Depending on the type of textile, the
following main programs are available:
Each of these main programs comprise
of a complete washing process,
including washing, rinsing and, if
required, spin cycles.
C Sort the laundry according to type
of fabric, color, degree of soiling and
permissible water temperature while
choosing a programme.
C Always select the lowest required
temperature. Higher temperature
means higher power consumption.
C For further programme details, see
“Programme Selection Table”
2.a - Spin Speed Indicator
2.b – Temperature Indicator
2.c – Spinning Symbol
2.d – Temperature Symbol
2.e – Remaining Time and Delaying Time
Indicator
2.f – Programme Indicator Symbols
(prewash/mainwash/rinsing/softener/
spinning)
2.g – Economy Symbol
2.h – Time Delaying Symbol
2.i – Door Locked Symbol
2.j – Start Symbol
2.k – Pause Symbol
2.l – Auxiliary Function Symbols
• Cottons
You can wash your durable clothes
at this programme. Your laundry shall
be washed with intense washing
movements during a longer washing
cycle. It is recommended for your
cotton clothes (such as bed sheets,
duvet and pillowcase sets, bathrobes,
underclothing, etc.).
Turning the machine on
Plug in your machine. Turn the tap on
completely. Check if the hoses are
connected tightly. Place the laundry
in the machine. Put in detergent and
softener. Press the “On/Off” button
(Figure 1-5).
• Synthetics
You can wash your less durable clothes
at this programme. Lighter washing
movements and shorter washing
cycle is used compared to “Cottons”
programme. It is recommended for
your synthetic clothes (such as shirts,
blouses, synthetic/cotton blended
garments, etc.). For curtains and veils, it
is recommended to use “Synthetic 40˚C”
programme with prewash and anti-
creasing functions selected. Detergent
should not be put in the prewash
Programme selection
Select the appropriate programme from
the programme table according to type,
amount and soiling degree of the laundry
and washing temperatures.
Bring the Programme Selection Knob
(Figure 1-4) to the programme mode
that you wish to wash your laundry at.
The recommended temperature and
spin speed for the selected programme
EN
16
compartment. Less detergent should be and at low temperature. We recommend
put in the main wash compartment as
the veil foams too much because of its
meshed structure.
you to use liquid detergent or woolen
shampoo for dark coloured laundry.
• Mixed Fabrics
• Woollens
You can use this program to wash
cottons and synthetics together without
needing to sort them.
You can wash your machine-washable
woollen garments at this programme.
Wash by selecting the proper
temperature according to the labels of
your clothes. It is recommended to use
appropriate detergents for woolens.
• Intensive
You can wash your durable and heavily
soiled clothes at this programme. In this
programme, your clothes will be washed
for a longer time and an extra rinsing
will be made compared to “Cottons”
programme. You can use it for your
heavily soiled clothes that you wish to be
rinsed sensitively.
Additional programmes
For special cases, there are also extra
programs available:
C Additional programs may differ
according to the model of your
machine.
Economy symbol
Shows energy saving programs and
temperature selections.
As “Intensive” and “Baby” programs are
long programs with higher temperature
selections to ensure hygiene, “Economy”
Symbol (Figure 2-2g) will not light up.
• Baby+Toddler Clothing
Increased hygiene is provided by a
longer heating period and an additional
rinse cycle. It is recommended for baby
clothes and clothes worn by allergic
people.
• Hand Wash
You can wash your woollen/delicate
clothes that bear “not machine-
washable” labels for which hand wash
is recommended at this programme.
It washes the laundry with very tender
washing movements without wearing
your clothes out.
Special programs
e
• Daily Quick
For specific applications, you can select
any of the following programs:
• Rinse
This programme is used when you want
to rinse or starch separately.
• Spin and drain
This programme is used to quickly
wash a small number of lightly soiled
cotton garments. E.g.: bathrobes, duvet
covers, sport wears, daily clothes and
etc. used only once.
• A Class 40
This program is used to apply an
additional spin cycle for the laundry or to
drain the water in the machine.
Before starting this program, select the
desired spin sped and press “Start/
Pause/Cancel” button. Your machine
drains the water after spinning at the set
spin speed.
If you only want to drain the water
without spinning your laundry, select
“Spin and drain” program, and then
select no spin function with spin speed
This programme washes for a longer
period at 40°C and gives the same result
as the “Cottons 60°C” programme, thus
it saves energy. It is suitable for clothes
for which you cannot use the “Cotton
60°C” programme.
• Darkcare
Use this programme to wash your
dark coloured laundry, or the coloured
laundry that you do not want them get
faded. This programme washes your
laundry with low mechanical movements
EN
17
selection button. Press “Start/Pause/
Cancel” button.
Spin Speed selection
Whenever a new programme is
selected, the maximum spin speed of
the selected programme is displayed on
the spin speed indicator (Figure 2-2a).
To decrease the spin speed, press
the “Spin” button (Figure 1-1). Spin
speed decreases gradually. Then, rinse
hold and no spin options are shown
respectively.
A You should use a lower spin speed
for delicate laundries.
Temperature selection
Whenever a new programme is
selected, the temperature anticipated
for that programme appears on the
temperature indicator (2b).
To change the temperature, press
the temperature button (Figure 1-3).
Temperature falls with 10° decrements.
Cold selection is shown with “-” symbol.
e
Rinse hold is shown with “ ” and no
spin is shown with “ ” symbols.
If you do not want to unload your
clothes immediately after the
programme, you may use the rinse hold
function in order to prevent your clothes
become wrinkled in an anhydrous
condition. With this function, your
laundry is kept in the final rinsing water.
If you want to spin your laundry after the
rinse hold function:
When the “Temperature” button is
pressed after coming to the Cold
selection, the maximum temperature of
the programme you have selected will
be displayed.
To decrease the temperature, press the
“Temperature” button again.
-
Adjust the spin speed.
Normally soiled, white
-
Press Start/Pause/Cancel Button.
Programme resumes. Your
machines drains the water and
spins your laundry.
cottons and linens. (Ex.:
90˚C
60˚C
coffee table covers,
tablecloths, towels, bed
sheets)
You can use no spin function in order to
drain the water without spinning at the
end of the programme.
Normally soiled, fade proof
colored linens, cottons
or synthetic clothes
(Ex.: shirts, nightgowns,
pajamas) and lightly soiled
white linen clothes (Ex.:
underwear)
For delicate clothes (Ex.: veil
curtains), blended clothes
including synthetics and
woolens.
40˚C
30°C
Cold
EN
18
Programme selection and consumption table
EN
2
Auxiliary functions
Programme
Cottons
90
7
7
7
7
7
3
3
54 2.70 max.
52 1.19 max.
64 0.72 max.
66 1.40 max.
66 2.70 max.
45 1.00 1000
45 0.45 1000
•
•
•
•
•
•
•
•
•
*
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
90-Cold
90-Cold
90-Cold
60-40
Cottons
60**
40
Cottons
Intensive
60
Baby&Toddler Clothing
Synthetics
Synthetics
Mixed Fabrics
Woollens
90
*
90-30
60
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
60-Cold
60-Cold
40-Cold
40-Cold
40
40
40 3.5 45 0.55 1000
40 1.5 56 0.30 600
A Class 40
Hand Wash
40
30
7
1
52 0.90 max.
40 0.25 600
30-Cold
max.
60 2.00
***
Daily Quick
Daily Quick
Daily Quick
90
60
7
7
•
•
•
•
•
90-Cold
90-Cold
max.
60 1.15
***
max.
70 0.20
***
30
40
7
3
•
90-Cold
40-Cold
Darkcare
82 0.55 800
*
• Selectable
* Automatically selected, not cancellable.
** Energy Label programme (EN 60456)
*** : Refers to 1400 rpm in machines with a highest spin speed above 1400 rpm.
Refers to the highest spin speed in machines with a highest spin speed below 1400
rpm.
Water and power consumption and programme duration may differ from the table
shown, subject to changes in water pressure, water hardness and temperature,
ambient temperature, type and amount of laundry, selection of auxiliary functions, and
fluctuations in the supply voltage.
“” programme may be selected instead of “Cotton 60” programme during
A Class 40
winter in areas where the input water temperature is low and/or in areas with low
supply voltage.
C The auxiliary functions in the table may differ according to the model of your
machine.
C Programme duration will be displayed on the screen of your machine according to
your selection.
EN
19
shortened. “F2” symbol will light up on
the display.
Auxiliary functions
Auxiliary function selection keys
•
Use this function for smaller
amounts or slightly soiled laundries.
• Extra Rinse
This function allows your machine to
perform an extra rinsing in addition to
the rinsing cycles performed by your
machine after main washing cycle.
Thus, the risk for sensitive skins (babies,
allergic skins and etc.) to be effected by
the minimal detergent remnants on the
laundry is reduced. “F3” symbol will light
up on the display.
11a
11b 11c
11d
• Anti- Crease
•
•
•
•
Depending on the programme,
you can select the desired auxiliary
function by pressing the buttons.
Select the required auxiliary
functions before starting the
programme.
Some combinations cannot be
selected together. (Ex.: Prewash
and Quick Wash.
Symbol of the selected auxiliary
function (Figure 2-2l) will light up.
With this function, boiler movement will
be lessened to prevent creasing and
spinning speed is limited. In addition,
washing is carried out at a higher water
level. “F4” symbol will light up on the
display.
•
Use this function for delicate
laundries that crease easily.
C Whenever you select this auxiliary
function, load your machine with
half of the maximum laundry amount
specified in the programme table.
Auxiliary function selection
If an auxiliary function that should not
be selected together with a previously
selected function is chosen, the first
selected function will be cancelled and
the last auxiliary function selection will
remain active.
Time screen
The display shows the time remaining
for the programme to complete while a
programme is running. Time is displayed
in hours and minutes as “01:30”.
(Ex.: If you want to select prewash first
and then quick wash, prewash will be
cancelled and quick wash will remain
active.
Auxiliary function that is not compatible
with the programme cannot be selected.
(see, “Programme Selection Table”)
• Prewash
When you select this function, the
display will indicate “F1” symbol.
Time delay
•
A prewash is only required with
heavily soiled laundry. Without
prewash you save energy, water,
detergent and time.
With the “Time delay” function you can
delay the programme start up to 24
hours. Setting can be made in intervals
of 30 minutes.
•
Prewash without detergent is
recommended for veils and curtains.
1. Open the loading door, place the
laundry inside and fill with detergent.
2. Set the washing programme,
temperature, spin speed and,
• Quick Wash
With this programme, the wash time is
EN
20
if required, select the auxiliary
functions.
2. Start symbol (Figure 2-2j) will fade.
The standby symbol (Figure 2-2k)
and the time delaying symbol (Figure
2-2h) will flash.
3. Press time delaying button “-”
(Figure 1-6) to decrease the desired
time delay. Programme duration
after 30 minutes shall be displayed.
4. Press “Start/Pause/Cancel Button”
to start the programme.
3. Press “Time delaying” buttons “+”
and “-” (Figure 1-6) to set your
desired time delay. Time delaying
symbol (Figure 2-2h) will flash.
4. Press “Start/Pause/Cancel” button
(Figure 1-8). Then the time delay
starts to count down. Time delaying
symbol (Figure 2-2h) will light up.
Start symbol (Figure 2-2j) will light
up.
Starting the programme
1. Press “Start/Pause/Cancel” button
(Figure 1-8) to start the programme.
2. The start symbol (Figure 2-2j) which
indicates that the programme has
started will light up.
3. The door locks and the door locked
symbol (Figure 2-2i) will light up.
4. Symbol of the relevant step
(prewash, main wash, rinse, softener
and spin) that the programme has
started from will light up (Figure
2-2f).
The “:” in the middle of the displayed
time delay will start flashing.
•
More laundry may be loaded or
taken out during the time delay
period. At the end of the time delay
countdown process, time delaying
symbol (Figure 2-2h) fades and the
washing starts as the programme
duration is displayed.
Changing the delay time
If you want to change the time during
the countdown:
1. Press “Start/Pause/Cancel” button
(Figure 1-8). “:” in the middle of the
screen will stop flashing. Standby
symbol (Figure 2-2k) will light up.
Time delaying symbol (Figure 2-2h)
will flash. Start Symbol (Figure 2-2j)
will fade.
2. Press “Time delaying” buttons “+”
and “-” (Figure 1-6) to set your
desired time delay.
3. Press “Start/Pause/Cancel” button.
Time delaying symbol (Figure 2-2h)
will light up. Standby symbol (Figure
2-2k) will fade. Start symbol (Figure
2-2j) will light up.
4. The “:” in the middle of the displayed
time delay will start flashing.
Progress of programme.
The progress of a running programme is
shown through a number of symbols on
the screen.
•
At the beginning of each programme
step, the relevant symbol in the
series of symbols will light up and
thus, at the end of the programme,
all symbols will remain lit up. The
symbol that is lit up at the far right of
the series of symbols indicates the
step that is being carried out.
Prewash
When “Prewash” auxiliary function is
selected, prewash symbol will light up to
indicate the beginning of prewash step.
Main wash
Cancelling the time delay
If you want to cancel the time delay
countdown and start the programme
immediately:
1. Press “Start/Pause/Cancel” button
(Figure 1-8). The “:” in the middle
of the displayed time delay will stop
flashing.
Main wash symbol will light up to
indicate that the main wash cycle has
started.
Rinse
Rinse symbol lights up at the beginning
of the rinse step.
EN
21
Softener
Adding/taking out laundry in standby
mode
Softener symbol lights up at the
beginning of softener step.
Spin
The door can be opened if the water
level is suitable. The door locked symbol
Spin symbol will light up at the beginning (Figure 2-2i) will light up until the door
of the final spin, during “Spin” and
“Pump” special programs.
is suitable for opening. This symbol will
fade out as soon as the door is allowed
to open. Laundry may be added / taken
out by opening the door.
•
If the machine is not spinning,
the programme may be in rinse
hold mode or the automatic
spin correction system has been
activated because of the excessive
unbalanced distribution of the
laundry in the machine.
Door lock
Door Locked Symbol (Figure 2-2i) lights
up when the loading door is locked. This
symbol will flash until the door is allowed
to open. Do not force the door at this
stage. This symbol will fade out as soon
as the door is allowed to open. You may
open the door after the symbol fades
out.
Changing the selections after
the programme has started
The selected spin speed and
programme temperature fade out. An
empty frame appears.
Child/key lock
When the “Programme selection” button
is brought to the appropriate position,
rpm and temperature data reappear.
You can protect the appliance from
being tampered or by accidental
operation by children of this lock. In this
case, no change can be made in the
running programme.
Switching the machine to standby
mode
C Your machine can be turned on
and off with On/Off button while the
child-proof lock is activated. In this
case, your machine will resume its
programme with child-proof lock
activated.
The machine is switched to child-lock
by pressing the 2nd and 4th auxiliary
functions for 3 sec. “C:on” (Child lock is
activated) label appears on the screen.
Machine is switched to standby mode
by pressing “Start/Pause/Cancel” button
(Figure 1-8) for a short time. Standby
symbol (Figure 2-2k) which indicates that
the machine is in standby mode lights
up and the start symbol (Figure 2-2j) that
shows the programme has started and
is still continuing fades out.
Selecting or cancelling an auxiliary
function in standby mode
Auxiliary functions can be cancelled or
selected in accordance with the step the
programme is at.
The same symbol will also be displayed
on the screen whenever any button
is pressed while the machine is child-
locked.
EN
22
To deactivate the child-proof lock,
press the 2nd and 4th auxiliary function
buttons for 3 sec.
“C:OFF” (Child lock is deactivated) label
appears on the screen.
(Figure 1-8). Standby symbol (Figure
2-2k) will fade. Start symbol (Figure 2-2j)
will light up. The programme continues
and only pumps out the water.
End of programme
When the programme is finished, the
symbols of the relevant steps will remain
lit up and the auxiliary function, spin
and temperature data selected at the
start-up of the programme will remain
selected. “End” label will appear on the
screen.
Ending the programme
through cancelling
“Start/Pause/Cancel” button (Figure
1-8) is pressed for 3 seconds to cancel
the programme. Start symbol (Figure
2-2j) will flash during cancellation.
After cancellation, the symbol of the
corresponding step at which the
cancellation was made will remain lit and
“End” label will appear on the screen.
Programme in rinse hold
mode
•
This process is shown with the
flashing Spin Symbol (Figure 2-2c)
and the lit up Standby Symbol
(Figure 2-2k).
If you wish to spin when the machine is
in this mode:
Adjust the spin speed. Press “Start/
Pause/Cancel” button (Figure 1-8).
The programme continues, pumps out
the water and spins. Standby Symbol
(Figure 2-2k) fades out and Start Symbol
(Figure 2-2j) lights up.
If you want to discharge the water only
without spinning:
Press “Start/Pause/Cancel” button
EN
23
6 Quick instructions for daily use
Preparation
programme starts). At the beginning
1. Turn the tap on completely. Check
that the hose is connected tightly.
2. Place the laundry in the machine.
3. Add detergent and softener.
of a washing cycle (machine allows
adding more laundry during a future
step only if the water level is low
enough to open the loading door or
if the temperature in the machine is
low).
Starting
In order to add laundry after the
start-up of the programme:
1. Press the “On/Off” button.
2. Select the programme and the
temperature.
1. Press “Start/Pause/Cancel” button.
2. Open the loading door and put in
more laundry.
3. If desired (according to your
machine’s model):
3. Close the loading door.
4. Press “Start/Pause/Cancel” button.
–
–
–
select any auxiliary function,
adjust the spin speed,
set the time delay,
4. Close the loading door.
Programme is in rinse hold mode
C This process is shown with the
flashing spin symbol and the
standby symbol which is lit up.
If you wish to spin when the machine is
in this mode:
5. Press “Start/Pause/Cancel” button.
The display shows the time remaining
for the programme to complete if time
delay is not set.
The display shows the time remaining
for the programme to start if the time
delay is set.
6. Check if the Door Locked Symbol
lights up on the screen.
The Door Locked Symbol (Figure 3-2i)
will light up if time delay is not set.
The Door Locked Symbol (Figure 3-2i)
will fade if time delay is set.
1. Adjust the spin speed.
2. Press “Start/Pause/Cancel” button.
The programme continues, pumps
out the water and spins.
3. The standby symbol fades out and
the start symbol lights up.
If you want to discharge the water
without spinning:
1. Press “Start/Pause/Cancel” button.
2. The standby symbol fades out and
the start symbol lights up.
Cancelling a programme
1. Press and hold the “Start/Pause/
Cancel” button for about 3 seconds; 3. The programme continues and only
the Start symbol will start flashing.
2. The machine can discharge all
the water or can take in water for
3 times at most to cool down the
clothes and complete discharging
process.
pumps out the water.
Re-spinning the laundry
The control system for an unbalanced
load can pause the spinning in cases
when the distribution of the laundry in
the drum is not balanced.
Adding more laundry
If you want to re-spin the clothes:
1. Distribute the laundry in your
machine for a balanced load.
2. Select the spin programme.
3. Adjust the spin speed.
•
This is only possible under the
following conditions:
–
during time delay,
C You may add or remove laundry
during the time delay (until the
EN
24
After the programme is finished
Programme indicator symbols on
the screen will remain lit after the
programme is finished. “End” will appear
on the screen.
1. Open the loading door and take out
the laundry when the door locked
symbol on the display fades out.
2. Press the “On/Off” button.
3. Turn the water tap off.
4. Remove any folds in the rubber seal
on the loading door and check for
debris.
5. Leave the loading door and
detergent drawer open to dry.
EN
25
7 Cleaning and care
C Foreign metal substances in your
machine can cause rust stains. In
such cases:
Detergent drawer
Remove any powder residue buildup in
the drawer. To do this;
Clean the drum with a stainless steel
cleaning agent. Never use steel wool
or wire wool.
1. Press the dotted point on the
siphon in the softener compartment
and pull towards you until the
compartment is removed from the
machine.
Outer cabinet and control
panel
When necessary:
•
Wipe the exterior panels of your
machine with soapy water or mild
detergent. Dry it with a soft cloth.
Use only a soft and damp cloth to
clean the control panel.
•
C Never use a sponge or scrubbing
material. These will damage the
painted and plastic parts.
C If more than a normal amount of
water and softener mixture starts to
gather in the softener compartment,
the siphon must be cleaned.
2. Wash the dispenser drawer
and the siphon with plenty of
lukewarm water in a washbasin.
Wear protective gloves or use an
appropriate brush to avoid touching
the residues in the drawer when
cleaning.
Inlet water filters
There is a filter at the end of each
water intake valve at the back side of
the machine and also at the end of
each water intake hose where they
are connected to the tap. These filters
prevent the foreign substances and dirt
in the water to enter into the machine.
Filters should be cleaned as they get
dirty.
3. Replace the drawer into its housing
after cleaning. Check if the siphon
is in its original location.
•
Close the taps.
The door and the drum
After each wash:
•
Check if there are any foreign
substances in the drum.
Open the hole in the bellow with the
aid of a toothpick if it is clogged.
•
•
Remove the nuts of the water intake
hoses to clean the surfaces of the
filters on the water intake valves with
an appropriate brush.
EN
26
•
•
If the filters are very dirty, you can
pull them out by means of pliers and
clean them.
Take out the filters on the flat
ends of the water intake hoses
together with the gaskets and clean
thoroughly under streaming water.
Replace the gaskets and filters
carefully and tighten the hose nuts
by hand.
3- An emergency drain hose is supplied
with some of our models. Others are not
supplied with this item.
If your product is supplied with an
emergency drain hose, do the following
as shown in the figure below:
•
Draining any remaining water
and cleaning the pump filter
Filter system in your machine prevents
solid items such as buttons, coins and
fabric fibers clogging the pump propeller
during discharging of the washing water.
•
•
Pull out the pump outlet hose from
its housing.
•
If your machine fails to drain the
water, the pump filter may be
clogged. You may have to clean
it every 2 years or whenever it is
blocked plugged. Water must be
drained off to clean the pump filter.
Place a large container at the end of
the hose. Drain the water off into the
container by pulling out the plug at
the end of the hose. If the amount
of water to be drained off is greater
than the volume of the container,
replace the plug, pour the water out,
then resume the draining process.
After draining process is completed,
replace the plug into the end of the
hose and fit the hose back into its
place.
In addition, water may have to be
drained off completely in the following
cases:
•
•
before transporting the machine
(e.g. when moving house)
•
when there is the danger of frost
In order to clean the dirty filter and
discharge the water;
If your product is not supplied with an
emergency drain hose, do the following
as shown in the figure below:
1- Disconnect or unplug the machine
from the power supply.
A There may be water at 90°C in the
machine. Therefore, the filter must
be cleaned only after the inside
water is cooled down to avoid
hazard of scalding.
2- Open the filter cap. The filter cap is
composed of one piece, hold it from
both sides and open it by pulling out.
•
•
Place a large container in front of
the filter to receive water flowing
from the filter.
Loosen pump filter (anticlockwise)
until water starts to flow out of it.
Direct the flowing water into the
container you have placed in front
of the filter. You can use a piece of
cloth to absorb any spilled water.
EN
27
•
•
•
When there is no water left, turn the
pump filter until it is completely loose
and remove it.
Clean any residues inside the filter
as well as fibers, if any, around the
propeller region.
If your product has a water jet
feature, be sure to fit the filter into
its housing in the pump. Never force
the filter while replacing it into its
housing. Fit the filter fully into its
housing; otherwise, water may leak
from the filter cap.
4- Close the filter cap of your product by
fitting the tabs on the bottom into their
positions and pushing the upper part of
it.
EN
28
8 Solution suggestions for problems
Cause
Explanation / Suggestion
Program cannot be started or selected.
Machine may have switched to
self protection mode due to an
infrastructure problem (such as line
voltage, water pressure, etc.).
Bring your machine to factory settings by turning
the program selection knob. (see, Ending the
program through canceling)
Water in the machine.
There may be some water in your
machine when you receive it. This is
from the quality control process and is
normal.
It is not harmful to your machine.
There is water coming from the bottom of the machine.
- Make sure that the seals of the water inlet hoses
are securely fitted.
There might be problems with hoses or
the pump filter.
- Tightly attach the drain hose to the tap.
- Make sure that the pump filter is completely
closed.
Machine does not fill with water
- Tap may be turned off.
- Open the inlet water taps fully.
- Flatten the water intake hose.
- Clean the water intake filter.
- Close the loading door.
- Water inlet hose might be bent.
- Water inlet filter might be clogged.
- The loading door may be ajar.
Machine does not discharge water.
- Water outlet hose might be clogged
or twisted.
- Pump filter may be clogged.
- Clean or flatten the hose.
- Clean the pump filter.
Machine vibrates or shakes.
- Machine feet might not be adjusted.
- Transportation safety bolts might
have not been removed.
- Adjust the machine feet.
- There may be a small amount of
laundry in the machine.
- Remove the transportation safety bolts.
- Add more laundry to the machine.
- Reduce the amount of laundry in the machine or
balance the load by hand.
- The machine may be overloaded
or the clothes may be distributed
unevenly.
- There machine might be touching a
solid surface.
- Ensure that nothing touches the machine.
Machine stops shortly after the program starts.
Machine can stop temporarily due to
low voltage.
It will resume operating when the voltage is back
to the normal level.
The water being taken in is directly discharged.
Connect the water draining hose as described in
the operation manual.
Improper position of the drain hose.
No water can be seen in the machine during washing.
This is not a problem. The water level
is not visible from the outside of the
machine.
EN
29
The door is jammed.
- Water level might be above the lower
level of the door.
- Machine might be heating up the
water or it may be at the spinning
cycle.
- Due to an electrical mechanism,
the door can only be opened a
few minutes after the program has
stopped.
- Run either the “Pump” or “Spin” program.
- Wait until the process is over.
- Wait until the process is over.
Machine fills with water when a process is cancelled.
For safety reasons, water should be cycled in and
out a couple times.
Inside of machine may be hot.
It continuously spins. Remaining time does not count down. (On models with display)
- The automatic spin correction system might have
been activated due to the unbalanced distribution
of the laundry in the drum.
- The laundry in the drum may be clustered
There may be an imbalance of laundry
(bundled laundry in a bag). Laundry should be
in the machine.
rearranged and re-spun.
- No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
Washing time takes longer than the time specified in the manual
- The machine will wait until there is sufficient
amount of water, which will lengthen the washing
time to avoid poor washing results due to
insufficient water.
- Washing time is extended to avoid poor washing
results when the supply voltage is low.
- Water pressure may be low.
- Supply voltage may be low.
- Input temperature of water may be
low.
- Cycle time is extended to heat up the water when
the input water is cold. Also, washing time can be
lengthened to avoid poor washing results.
- The automatic spin correction system might have
been activated due to the unbalanced distribution
of the laundry in the drum.
- There may be an imbalance of
laundry in the machine.
- Number of rinses and/or amount of
rinse water might have increased.
- The laundry in the drum may be clustered
(bundled laundry in a bag).
- Laundry should be rearranged and re-spun.
- No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
- Water amount is increased to obtain a better
rinse and a rinse cycle is added when necessary.
EN
30
It continuously washes. Remaining time does not count down.
- The machine will wait until there is sufficient
In the case of a paused countdown
while taking in water:
amount of water to avoid poor washing results due
to lack of water. Then the timer will start to count
down.
- Timer will not countdown until the
machine is filled with the correct
amount of water. (On models with
display)
- Time will not count down until the selected
temperature for the program is attained.
- The automatic spin correction system might have
been activated due to the unbalanced distribution
of the laundry in the drum.
- The laundry in the drum may be clustered
(bundled laundry in a bag). Laundry should be
rearranged and re-spun.
- No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
- Time might have gotten stuck during
heating step. (On models with display)
In the case of a paused countdown at
the spinning step:
There may be an imbalance of laundry
in the machine. (On models with
display)
It did not spin.
- The automatic spin correction system might have
been activated due to the unbalanced distribution
of the laundry in the drum.
- There may be an imbalance of
laundry in the machine. Therefore, the
program might have been completed
without spinning.
- The machine will not spin if the water
has not completely drained.
- The laundry in the drum may be clustered
(bundled laundry in a bag). Laundry should be
rearranged and re-spun.
- No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
- Check the filter.
- Check the drain hose.
Washing performance is poor: Laundry turns grey
- Using insufficient amount of
detergent for a long time,
- Washing at low temperatures for a
long time,
- Use the recommended amount of detergent
appropriate for water hardness and the laundry.
- Select the proper temperature for the laundry to
be washed.
- Using insufficient amount of
- If the water hardness is high, using an insufficient
detergent for hard waters (soil can stick amount of detergent can cause laundry to turn
to the laundry),
- Using excessive amount of detergent - It is difficult to eliminate such greyness once it
(detergent can stick to the laundry). occurs.
grey over time.
Washing performance is poor: Stain could not be removed, not cleaned. Laundry could not
be whitened.
- Insufficient amount of detergent used.
- Use recommended amount of detergent
- Excessive laundry loaded into
appropriate for the laundry.
machine
- Do not load the machine in excess.
- Wrong program and temperature
- Select the proper program and temperature for
might have been selected.
the laundry to be washed.
- Improper detergent may have been
- Put the detergent in the correct compartment.
used.
- Do not mix detergent with bleaching agents.
- Wrong type of detergent used.
EN
31
- Washing performance is poor: Oily stains appear on laundry.
- Washing performance is poor: Bad odour
- Such odours and bacteria layers are formed on
the drum as a result of continuous washing at
lower temperatures and/or in short programs.
- Leave the detergent dispenser drawer as well
as the loading door of the machine ajar after each
washing. Thus, a humid environment favorable for
bacteria cannot be created inside the machine.
- Machine must be operated empty either at 60°C
or 90°C program with detergent every 6 months.
- Oily accumulations on the drum may
have stuck to the laundry.
- Oily accumulations on the drum may
have stuck to the laundry.
Colour of the clothes faded.
- Do not load the machine in excess
- Store detergent in a closed and dry location.
- Do not keep them under high temperatures.
- Select the proper program and temperature
according to the type and soiling degree of the
laundry.
- Excessive laundry loaded into
machine.
- Detergent may have gotten damp.
- A higher temperature might have
been selected.
It does not rinse well.
- Store detergent in a closed and dry location. Do
not keep them under high temperatures.
- If detergent is put in the prewash compartment
although prewash cycle is not selected, machine
can take this detergent during rinsing or softener
- The amount, brand and storage
conditions of the detergent used might step.
not be appropriate.
- Check the filter.
- Detergent might have been put in the - Check the drain hose.
wrong compartment.
- There may be an imbalance of laundry in the
- Machine filter may be clogged.
- Drain hose may be folded.
- Intermediate spins may be skipped.
machine.
- The laundry in the drum may be clustered
(bundled laundry in a bag). Laundry should be
rearranged and re-spun.
- No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
Clothes stiffened.
- If the water hardness is higher, using insufficient
amount of detergent can cause the laundry to
become stiff in time. Use appropriate amount of
- Insufficient amount of detergent used. detergent according to the water hardness.
- The detergent may have been
placed into the wrong compartment;
the detergent may be mixed with the
softener.
- If detergent is put in the prewash compartment
although prewash cycle is not selected, machine
can take this detergent during rinsing or softener
step.
- Do not mix the softener with detergent when
putting in the compartment.
- Wash and clean the drawer with hot water.
EN
32
Clothes do not smell like the softener.
- If the water hardness is higher, using insufficient
amount of detergent can cause the laundry to
become stiff in time. Use appropriate amount of
detergent according to the water hardness.
- If detergent is put in the prewash compartment
although prewash cycle is not selected, machine
can take this detergent during rinsing or softener
step.
- Insufficient amount of detergent used.
- The detergent was placed into the
wrong compartment; the detergent
was mixed with the softener.
Do not mix the softener with detergent when
putting in the compartment.
Wash and clean the drawer with hot water.
Detergent residue in the dispensing drawer.
- Dry the detergent drawer before putting in
- Detergent may have been put in wet
dispenser drawer.
detergent.
- Store detergent in a closed and dry location.
- Do not keep them under high temperatures.
- The detergent dispenser outlet (holes) may have
a problem.
- There might be problems with the detergent
dispenser valves.
- Do not mix the softener with detergent when
putting in the compartment.
- Detergent may have gotten damp.
- Water pressure might be low
- The detergent in the main wash
compartment might have gotten wet
while taking in the prewash water..
- Detergent might be mixed with the
bleaching agent.
There is detergent left on the laundry.
- Excessive laundry loaded into
machine.
- Wrong program and temperature
might have been selected.
- Wrong detergent may have been
used.
- Do not load the machine in excess.
- Select the proper program and temperature for
the laundry to be washed.
- Use wool detergents for woolens.
There is too much foam
.
- Use only automatic washing machine detergents
in your washing machine.
- You may not be using proper
detergent for automatic washing
machines.
- Use only sufficient amount of detergent.
- Use only sufficient amount of detergent.
- Store detergent in a closed and dry location.
- Do not store in excessively hot places.
- Use smaller amounts of detergent for lace items.
- If you put detergent in the prewash
- Excessive amount of detergent may
have been used.
- Too much detergent may have been
used for a small amount of lightly soiled
laundry.
compartment although you have not selected
a prewash cycle, the machine can take this
detergent during rinsing or softener step.
- Too much softener was put in.
- Detergent may have been stored
improperly.
- Type of material being washed (lace
items will cause excessive foam due to
their meshed structure).
The detergent dispenser is problematic. Water
is siphoned (pulling the softener into the washer
early) during the fill or rinse cycles.
- Detergent might have been put in the
wrong compartment.
Valves are problematic.
- Softener being released early.
EN
33
Machine does work. Nothing is displayed on the screen.
The plug might not be plugged in the
mains outlet.
Check the plug.
Fuse may have blown.
Electricity may be cut off.
The “On/Off” button might have not
been pressed.
Check the fuse.
Check the supply power.
Press this button.
The machine did not start after the program was selected and the «Start/Pause/Cancel»
button was pressed.
The front door may be ajar.
The Rinse Symbol amongst the Program Indicator Symbols is flashing. (Subject to the
model of your machine, water cut-off symbol may light up too)
You can restart your machine by pressing the
Water may have been cut off.
«Start/Pause/Cancel» button for a short time after
ensuring that the water is not cut off.
EN
34
9 Guarantee
Your new Beko product is guaranteed
against the cost of breakdown repairs
for twelve months from the date of the
original purchase.
domestic household premises.
The product must be correctly
installed, located and operated in
accordance with the instructions
contained in the User Instructions
Booklet provided.
Professional installation by a
qualified Electrical Domestic
Appliance Installer is recommended
for all Washing Machines,
Dishwashers and Electric Cookers
Gas Cookers must only be installed
by a CORGI (or BORD GAIS)
registered Gas Installer.
The guarantee is given only within
the boundaries of the United
Kingdom and the Republic of
Ireland.
The guarantee is applicable only to
new products and is not transferable
if the product is resold.
•
•
What is covered?
•
Repairs necessary as a result
of faulty materials, defective
components or manufacturing
defect.
•
•
The cost of functional replacement
parts, but excluding consumable
items.
The labour costs of a Beko
approved repairer to carry out the
repair.
•
•
What is not covered?
•
Transit, delivery or accidental
damage or misuse and abuse.
Cabinet or appearance parts,
including knobs, flaps, handles or
container lids.
•
•
•
•
Beko disclaims any liability for
incidental or consequential
damages.
The guarantee does not in anyway
diminish your statutory or legal
rights.
•
•
Accessories or consumable items
including but not limited to, ice trays,
scrapers, cutlery baskets, filters and
light bulbs.
Repairs required as a result of
unauthorised repair or inexpert
installation that fails to meet the
requirements contained in the user
instruction book.
Should you experience any difficulty in
obtaining service please contact the
Beko Customer Help-Line.
Tel: 0845 600 4911
e-mail:[email protected]
•
•
Repairs to products used on
commercial or non-residential
household premises.
Loss of frozen food in freezers
or fridge/freezers. (Food loss
insurance is often included within
your household contents insurance
policy, or may be available
separately from your retailer).
Important notes.
•
Your Beko product is designed and
built for domestic household use
only.
The guarantee will be void if the
product is installed or used in
commercial or non-residential
•
Download from Www.Somanuals.com. AElNl Manuals Search And Download.
35
10 Service
Please keep your purchase receipt
or other proof of purchase in a safe
place; you will need to have it should
the product require attention under
guarantee.
agreement document. Otherwise please
call the appropriate number above
where service can be obtained at a
charge.
Should you experience any difficulty in
obtaining service please contact the
Beko Customer Help-Line.
Tel: 0845 600 4911
e-mail:[email protected]
You should also complete the details
below; it will help us assist you when
requesting service. (The model number
is printed on the Instruction Booklet
and the serial number is printed on the
Rating Label affixed to the appliance)
Model No:
Serial No:
Retailer:
Date of purchase:
For service under guarantee simply
telephone the appropriate number below
UK Mainland & Northern Ireland
Fridges & Freezers
Electric Cookers
Gas &
0845 600 4903
0845 600 4902
0845 600 4905
Dual Fuel Cookers
Washing Machines &
Dishwashers
0845 600 4906
Republic of Ireland
All Refrigeration,
All Cookers
01 862 3411
Washing Machines & Dishwashers
Before requesting service please
check the trouble-shooting guide in the
Operating Instructions as a charge may
be levied where no fault is found even
though your product may still be under
guarantee.
Service once the manufacturers
guarantee has expired.
If you have purchased an extended
guarantee please refer to the instructions
contained within the extended guarantee
Download from Www.Somanuals.com. AEllNManuals Search And Download.
36
|