User’s Manual
Version 1.0 August 2003
TRUTH B2030P/B2031P
TRUTH
High-Resolution, Ultra-Linear Reference Studio Monitor
s
s
s
s
High-resolution, passive 2-way 100-Watt (B2030P) / 150-Watt (B2031P) nearfield monitor
Ultra-linear frequency response from 75 Hz to 21 kHz (B2030P) / 55 Hz to 21 kHz (B2031P)
Extremely high-resolution, ferrofluid-cooled tweeter
Long-throw 6 ¾" woofer (B2031P: 8 ¾") with special polypropylene diaphragm and deformation-resistant
aluminum die-cast chassis
s
Controlled dispersion characteristics and extremely large “sweet spot” through BEHRINGER’s wave
guide technology
s
s
s
s
s
Phase-optimized, low-distortion frequency crossover for accurate reproduction
Magnetically shielded for placement near computer monitors
Delivered as “matched pairs”
Low-vibration, environment-friendly E1 MDF cabinet
Designed in Germany. Manufactured under ISO9000 certified management system
3
TRUTH B2030P/B2031P
FOREWORD
TABLE OF CONTENTS
Dear Customer,
1. INTRODUCTION ......................................................... 4
welcome to the team of
BEHRINGER users, and
thank you very much for
expressing your confi-
dence in us by pur-
chasing this studio
monitor.
1.1 Before you get started ................................................... 5
1.1.1 Shipment ............................................................... 5
1.1.2 Initial operation...................................................... 5
1.1.3 Warranty .............................................................. 5
2. CONTROL ELEMENTS ............................................... 5
Writing this foreword
for you gives me great
pleasure, because it
3. APPLICATION ............................................................ 5
3.1 Connection ...................................................................... 5
3.1.1 The truth about speaker cables ........................... 6
3.1.2 Power amp ........................................................... 6
3.1.3 Protecting your TRUTH......................................... 6
3.2 Speaker placement suggestions .................................... 6
3.3 Adapting the TRUTH to the room acoustics................... 7
represents the culmi-
nation of many months
of hard work delivered
by our engineering team
to achieve a very ambi-
tious goal: to present
two outstanding near-
field monitors, whose
neutral sound makes
4. SPECIFICATIONS ....................................................... 7
5. WARRANTY ................................................................ 8
them ideal for studio use. The task of designing our new B2030P
and B2031P certainly meant a great deal of responsibility, which
we assumed by focusing on you, the discerning user and
musician. Meeting your expectations also meant a lot of work
and night shifts. But it was fun, too. Developing a product usually
brings a lot of people together, and what a great feeling it is
when all who participated in such a project can be proud of
what they’ve achieved.
1. INTRODUCTION
Congratulations! With our new BEHRINGER TRUTH you have
purchased one of the best high-resolution passive studio
monitors available. It is a tool that reproduces your program
material with highest fidelity and balance, positioning sound
sources accurately on the stereo basis.
It is our philosophy to share our enjoyment with you, because
you are the most important member of the BEHRINGER team.
With your highly competent suggestions for new products you’ve
made a significant contribution to shaping our company and making
it successful. In return, we guarantee you uncompromising quality
as well as excellent technical and audio properties at an extremely
reasonable price. All of this will enable you to give free rein to
your creativity without being hampered by budget constraints.
The TRUTH speakers stand out thanks to their toughness and
extremely neutral and authentic sound rendition. In the bass
range, they operate with polypropylene membranes and smooth
suspension. Their scope is broadened downward by using a
special bass reflex system. In the upper frequency range, a
specially developed ferrofluid-cooled aluminum tweeter provides
for subtle signal reproduction. The TRUTH is magnetically shielded,
so you can use it near computer monitors or TV sets. The audio
signal is separated using a low-distortion crossover that creates
a phase-optimized frequency separation.
We are often asked how we manage to produce such high-
quality devices at such unbelievably low prices. The answer is
quite simple: it’s you, our customers! Many satisfied customers
mean large sales volumes enabling us to get better purchasing
terms for components, etc. Isn’t it only fair to pass this benefit on
to you? Because we know that your success is our success
too!
We recommend that you experiment with your TRUTH away
from the pressures of a recording session, in order to get a feel
for it. It will be a good idea to listen to your favorite CD’s over the
TRUTH, so that you can get an impression of the neutral sound
this speaker produces—which might be somewhat unusual at
first!
I would like to thank all of you who have made the TRUTHs
possible. You have all made your own personal contributions,
from the developers to the many other employees at this company,
and to you, the BEHRINGER user.
+
The following user’s manual is intended to
familiarize you with the unit’s control elements,
so that you can master all the functions. After having
thoroughly read the user’s manual, store it at a safe
place for future reference.
My friends, it’s been worth the effort!
Thank you very much,
Uli Behringer
ATTENTION!
+
The TRUTH is capable of producing extreme
volumes. Please bear in mind, that high sound
pressures do not only temporarily damage your
sense of hearing, but can also cause permanent
damage. Be careful to select a suitable volume.
4
1. INTRODUCTION
TRUTH B2030P/B2031P
This is the terminal clamp for the minus cord of your speaker
cable.
1.1 Before you get started
1.1.1 Shipment
This is the terminal clamp for the plus cord of your speaker
cable.
The B2030P/B2031P were carefully packed at the factory to
assure secure transport. Should the condition of the cardboard
box suggest that damage may have taken place, please inspect
the unit immediately and look for physical indications of damage.
The connection terminal of your TRUTH is recessed. This way,
you can place it in the vicinity of walls.
+
Always power down your amp before connecting it
to the TRUTH.
+
Damaged units should NEVER be sent directly to us.
Please inform the dealer from whom you acquired
the unit immediately as well as the transportation
company from which you took delivery of the unit.
Otherwise, all claims for replacement/repair may
be rendered invalid.
SERIAL NUBMER. Please take a few minutes and send to
us a completely filled out warranty card within 14 days of
the original date of purchase. Otherwise, warranty claims
may be rendered invalid. Or fill out the warranty information
1.1.2 Initial operation
The TRUTHs must be placed on a flat and stable surface.
3. APPLICATION
1.1.3 Warranty
3.1 Connection
Please take a few minutes and send us the completely filled
out warranty card within 14 days of the date of purchase. You
needed for the registration is located on the rear of the unit.
Failure to register your product may void future warranty claims.
2. CONTROL ELEMENTS
The control elements described in the following are the same
on both speakers.
Fig. 3.1: Connecting an amplifier
Please follow these steps to connect your TRUTHs to a power
amp: Loosen the plus screw (red ring with a “+”) and the minus
screw (black ring with a “-”). Now insert the plus cord of the
speaker cable connecting the amp to your TRUTH into the plus
opening. Then, connect the minus cable into the minus opening.
Tighten the screws. Do the same to connect the other TRUTH.
+
Make sure that all connections are done properly.
Speaker cables are color-coded to help avoid
confusion. You’ll know that the signal is inverted
(i.e. you’ve mixed up the connections) when you
notice that bass frequencies are getting lost and
when the stereo characteristic of the signal is
majorly worse.
+
Always make sure that bare wire ends never touch
the open end of another speaker cable, speaker
connectors or metal parts of your amp.
Fig. 2.1: Rear panel connectors
3. APPLICATION
5
TRUTH B2030P/B2031P
The BEHRINGER TRUTH B2030P/B2031P is a so-called near-
field monitor, which means that the impact of the room acoustics
on the sound will be reduced considerably owing to the short
distance between speaker and listener.
3.1.1 The truth about speaker cables
Carefully approach the choice of what cables you use. Which
cables you use can have a major influence on your sound.
Cables of various lengths and diameters affect the resistance
value—causing a loss in power.
On the other hand, that doesn’t mean that you should be buying
high-end cables that cost as much as your speakers. Simply use
the following rule of thumb: Whenever possible, use cables with
large diameters (gauge) and keep the cable length to a minimum.
The screw clamps on your TRUTH can accept cable thickness
of up to 7 mm² (9 AWG).
3.1.2 Amp
The power rating of the amp you use should be roughly twice
the load capacity of your TRUTH. Consequently, the B2030P
should be operated with an amp with a load capacity of 2 x 200
Watts, and the B2031P with an amp with a load capacity of
2 x 300 Watts.
Fig. 3.2: Incorrect speaker setup
This illustration shows how you shouldn’t do it: you can clearly
see that a portion of the sound bounces back from the walls
before it reaches the listener’s ears. Thus, direct and reflected
sound waves overlap which results in a coloration of the sound.
Also, you should keep in mind the impedance of your TRUTH in
order to guarantee optimal power delivery. The B2031P’s
impedance is 4 Ω, whereas the B2030P’s is 8 Ω. Use an amp
whose power rating roughly corresponds to the values
recommended in the table. The impedance should correspond to
the values listed in the table:
TRUTH
B2030P
B2031P
Amp power rating
200 W into 8 Ohm
300 W into 4 Ohm
Tab. 3.1: Recommended amp power ratings
Of course, you can use amps with higher power ratings.
However, make sure not to exceed the load capacity of your
TRUTH. Damage to speaker components caused by exceeding
their load capacity is not covered by the warranty.
Fig. 3.3: Correct speaker setup
3.1.3 Protecting your TRUTH
To ensure that your B2030P/B2031P last for years to come,
you should definitely keep the following in mind:
This effect can be reduced by turning the speakers towards
the listener. To make reflections from ceiling or floor less likely,
the tweeters should be on the same height as your ears. Please
note that the TRUTH should be operated vertically. Where this is
impossible, place it horizontally as shown in the illustration (i.e.
woofers closer to each other), to allow for an improved stereo
image.
s
Always turn the volume down on your amp before
switching it on or off.
s
When powering your equipment up/down, the amp should
always be the last one to be powered up and the first one
to be powered down. This way, you avoid loud crackling
noise that occurs when you turn studio equipment on or
off.
s
s
Always make sure your audio signal level is optimally set.
Avoid overdriving your amp.
Do not push your studio monitors beyond their physical
limitations. Even though your TRUTH has sufficient power
overhead, you can still damage it if you drive it too much or
crank the volume all the way up for longer periods of time.
Fig. 3.4: TRUTH setup horizontally
Not only the physical location of speakers but also the acoustic
characteristics of the room have a substantial effect on the way
your TRUTH sounds. Make sure that the room neither sounds too
hall-like nor too dull—basically, neither like a bathroom nor totally
without an echo. You can alter the room acoustics easily by
installing or removing carpets, curtains or furniture. Fabric
covering on the wall opposite the speakers might be a good idea
if the room is too reflective. The next chapter describes how to
adapt the TRUTH to the room acoustics, once it has been set up
properly.
3.2 Speaker placement suggestions
Since the sound of a speaker depends to a great extent from
its surroundings, placing your TRUTH correctly is very important.
Please try to follow these suggestions through. Your efforts will
be rewarded with better sound and higher resolution.
Both speakers are built identically. There is no need to concern
yourself with which speaker should be placed left and which
speaker should be placed right. Place the TRUTHs on a flat and
stable surface, if possible use a dedicated speaker stand. In this
way, the speaker is acoustically decoupled and won’t induce
vibrations in nearby objects, which would affect the bass
response. If you cannot use a stand, put the TRUTHs on spikes
or damping foam material. Another aspect is the distance between
speaker and wall: keep the speaker away from the wall, as this
would emphasize the bass response, particularly in corners,
where two walls form an angle.
6
3. APPLICATION
TRUTH B2030P/B2031P
3.3 Adapting the TRUTH to the room acoustics
4. SPECIFICATIONS
To acoustically adapt your TRUTH to your control room, in
cases when the speakers are located in unusual places or when
you have specific sound requirements, you may have to use an
external equalizer. It should be connected in the signal path
between your mixing console and your amp.
CONNECTORS
Type
Binding posts
SYSTEM SPECIFICATIONS
B2030P
Power rating
Impedance
Frequency response 75 Hz to 21 kHz
Sound pressure level 89 dB (1 W/1 m)
100 watts
8 Ω
The BEHRINGER ULTRACURVE PRO DEQ2496 has proven its
usefulness in practice, as it is not only a simple equalizer but
also features a real-time analyzer. You can use our measuring
microphone ECM8000 to automatically adapt the TRUTH to your
room or modify its frequency response.
B2031P
Power rating
Impedance
Frequency response 55 Hz to 21 kHz
Sound pressure level 89 dB (1 W/1 m)
As a general rule, you should set up and adjust the TRUTH
with great care. Above all, you should take your time: unlike hi-fi
speakers, the TRUTH is tuned to produce a neutral sound, which
can be confusing when you are working for the first time with
such a high-quality speaker. Don’t try to adjust the TRUTH with
an equalizer to produce a “bombastic” sound that impresses you
or other listeners. To get a feeling for the TRUTH’s sound, you
should listen to as many records as possible that were produced
in other studios. We also recommend that you listen to your own
recordings over as many other systems as possible, for example,
your car system. If you find that your mixes are somewhat “dull”
in their overall sound, the reason might be too much treble from
your TRUTH. On the other hand, if you set the bass level too
high, you will find that your mixes lack bass power. Tuning a
speaker can take several days’ time, so once again: take your
time!
150 watts
4 Ω
COMPONENTS
B2030P
Tweeter
Woofer
¾" dome, ferrofluid-cooled
6 ¾" polypropylene diaphragm
B2031P
Tweeter
Woofer
1" dome, ferrofluid-cooled
8 ¾", polypropylene diaphragm
CROSSOVER
B2030P
Crossover frequency 2.3 kHz
B2031P
Crossover frequency 2 kHz
DIMENSIONS/WEIGHT
B2030P
Dimensions (H x W x D) 12 1/2" (317 mm) x 8 2/5" (214 mm)
x 8 3/10" (211 mm)
Weight
15 1/3 lbs. (7.0 kg)
B2031P
Dimensions (H x W x D) 15 4/5" (401 mm) x 10 1/10" (257 mm)
x 10 1/2" (267 mm)
Weight
25 1/3 lbs. (11.5 kg)
BEHRINGER is constantly striving to maintain the highest professional
standards. As a result of these efforts, modifications may be made from
time to time to existing products without prior notice. Specifications and
appearance may differ from those listed or illustrated.
4. SPECIFICATIONS
7
TRUTH B2030P/B2031P
5. WARRANTY
§ 1 WARRANTY CARD/ONLINE REGISTRATION
3. Free inspections and maintenance/repair work are expressly
excluded from this warranty, in particular, if caused by improper
handling of the product by the user. This also applies to defects
caused by normal wear and tear, in particular, of faders,
crossfaders, potentiometers, keys/buttons, tubes and similar
parts.
To be protected by the extended warranty, the buyer must
complete and return the enclosed warranty card within 14 days
of the date of purchase to BEHRINGER Spezielle Studiotechnik
GmbH, in accordance with the conditions stipulated in § 3. Failure
to return the card in due time (date as per postmark) will void any
extended warranty claims. Based on the conditions herein, the
buyer may also choose to use the online registration option via
4. Damages/defects caused by the following conditions are
not covered by this warranty:
s improper handling, neglect or failure to operate the unit in
compliance with the instructions given in BEHRINGER user
or service manuals.
§ 2 WARRANTY
1. BEHRINGER (BEHRINGER Spezielle Studiotechnik GmbH
including all BEHRINGER subsidiaries listed on the enclosed page,
except BEHRINGER Japan) warrants the mechanical and
electronic components of this product to be free of defects in
material and workmanship for a period of one (1) year* from the
original date of purchase, in accordance with the warranty
regulations described below. If the product shows any defects
within the specified warranty period that are not excluded from
this warranty as described under § 3 and 4, BEHRINGER shall, at
its discretion, either replace or repair the product using suitable
new or reconditioned parts. In the case that other parts are used
which constitute an improvement, BEHRINGER may, at its
discretion, charge the customer for the additional cost of these
parts.
s connection or operation of the unit in any way that does not
comply with the technical or safety regulations applicable in
the country where the product is used.
s damages/defects caused by force majeure or any other
condition that is beyond the control of BEHRINGER.
5. Any repair or opening of the unit carried out by unauthorized
personnel (user included) will void the warranty.
6. If an inspection of the product by BEHRINGER shows that
the defect in question is not covered by the warranty, the
inspection costs are payable by the customer.
7. Products which do not meet the terms of this warranty will
be repaired exclusively at the buyer’s expense. BEHRINGER will
inform the buyer of any such circumstance. If the buyer fails to
submit a written repair order within 6 weeks after notification,
BEHRINGER will return the unit C.O.D. with a separate invoice
for freight and packing. Such costs will also be invoiced
separately when the buyer has sent in a written repair order.
2. If the warranty claim proves to be justified, the product will
be returned to the user freight prepaid.
3. Warranty claims other than those indicated above are
expressly excluded.
§ 3 RETURN AUTHORIZATION NUMBER
§ 5 WARRANTY TRANSFERABILITY
1. To obtain warranty service, the buyer (or his authorized
dealer) must call BEHRINGER (see enclosed list) during normal
business hours BEFORE returning the product. All inquiries must
be accompanied by a description of the problem. BEHRINGER
will then issue a return authorization number.
This warranty is extended exclusively to the original buyer
(customer of retail dealer) and is not transferable to anyone
who may subsequently purchase this product. No other person
(retail dealer, etc.) shall be entitled to give any warranty promise
on behalf of BEHRINGER.
2. Subsequently, the product must be returned in its original
shipping carton, together with the return authorization number to
the address indicated by BEHRINGER.
§ 6 CLAIM FOR DAMAGES
Failure of BEHRINGER to provide proper warranty service shall
not entitle the buyer to claim (consequential) damages. In no
event shall the liability of BEHRINGER exceed the invoiced value
of the product.
3. Shipments without freight prepaid will not be accepted.
§ 4 WARRANTY REGULATIONS
1. Warranty services will be furnished only if the product is
accompanied by a copy of the original retail dealer’s invoice.
Any product deemed eligible for repair or replacement under the
terms of this warranty will be repaired or replaced.
§ 7 OTHER WARRANTY RIGHTS AND NATIONAL LAW
1. This warranty does not exclude or limit the buyer’s statutory
rights provided by national law, in particular, any such rights
against the seller that arise from a legally effective purchase
contract.
2. If the product needs to be modified or adapted in order to
comply with applicable technical or safety standards on a national
or local level, in any country which is not the country for which
the product was originally developed and manufactured, this
modification/adaptation shall not be considered a defect in
materials or workmanship. The warranty does not cover any
such modification/adaptation, irrespective of whether it was
carried out properly or not. Under the terms of this warranty,
BEHRINGER shall not be held responsible for any cost resulting
from such a modification/adaptation.
2. The warranty regulations mentioned herein are applicable
unless they constitute an infringement of national warranty law.
* Customers in the European Union please contact BEHRINGER
Germany Support for further details.
The information contained in this manual is subject to change without notice. No part of this manual may be reproduced or
transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for any
purpose, without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH.
BEHRINGER is a registered trademark.ALL RIGHTS RESERVED.
© 2003 BEHRINGER Spezielle Studiotechnik GmbH.
BEHRINGER Spezielle Studiotechnik GmbH, Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Münchheide II, Germany
Tel. +49 2154 9206 0, Fax +49 2154 9206 4903
8
5. WARRANTY
|