Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
Item#: PY81988
Check that you have all the below parts for this model
before assembling the playard.
Playard (fully assemble) x 1
Mobile Lower Arm x 1
Mobile Arm Holder x 1
Mobile Upper Curved Arm x 1
Mobile Tri-shaped Arm x 1
Toy Animal x 3
Mattress x 1
Bassinet x 1
Metal Support Tubes (2 male, 2 female)
Diaper Stacker x 1
Travel / Storage Bag x 1
IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT,
PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT
1-800-328-7363 BETWEEN THE HOURS OF 8:00 A.M. AND 4:30 P.M. PACIFIC
STANDARD TIME FOR ASSISTANCE. PLEASE HAVE YOUR MODEL NUMBER AND
MANUFACTURING DATE AVAILABLE WHEN YOU CALL. THIS INFORMATION CAN BE
FOUND ON A SMALL STICKER UNDER THE PLAYARD.
*Toys and mobile may vary
Instruction Manual
Convenience through innovation and thoughtful design
10.09
Contact us by mail:
Baby Trend, Inc.
1607 S. Campus Ave., Ontario, CA 91761
Contact us by phone:
1-800-328-7363 (8:00am ~ 4:30pm PST)
Convenience through innovation and thoughtful design
PARTS
ASSEMBLY
TO ASSEMBLE PLAYARD
IMPORTANT!To ensure safe operation of your playard,
please follow these instructions carefully. Please keep these
instructions for future reference.
IMPORTANT! Before assembly and each use, inspect this
product for damaged hardware, loose joints, missing parts or sharp
edges. NEVER use if any parts are mssing or broken.
IMPORTANT!Adult assembly is required.
Mattress
Playard
Check the parts list on the back cover to make sure you have
all the parts for this model before assembling the playard.
ATTENTION:
Playard must be fully assembled and securely
locked before installing or using other accessories.
1. Unzip bag and remove Playard frame (Fig. 1).
Undo the three (3) Fasten straps and set the
Mattress aside.
Fig. 1
Mattress
2. DO NOT push center down yet.
3. Top rails must be fully erected before lowering
center. Pull up one rail at a time, hold one hand
on each side of the rail and pull up sharply, do
not pull from the middle where the center latch
release is located, make sure both tubes latch in
place and each rail is rigid. (Fig. 2).
Playard
Travel / Storage Bag
IMPORTANT: The center must be raised
while locking the rails. If one rail will lock
but the other side will not then, unlock the rail
by squeezing the release in the center and try
again.
Fig. 2
Diaper Stacker
Bassinet
4. Once all four (4) top rails are locked in place,
push down on the center handle (Fig. 3). The
center mechanism will rotate clockwise 90
degrees and automatically lock in place.
Metal Support Tubes
(2 male, 2 female)
Fixed Mobile*
*Toy type vary
Fig. 3
Copyright © 2009 - 2010, Baby Trend Inc., All Rights Reserved.
Copyright © 2009 - 2010, Baby Trend Inc., All Rights Reserved.
3
4
ASSEMBLY
ASSEMBLY
FOLDING PLAYARD
1. Release the three (3) Velcro® straps holding
the Mattress from underneath the Playard floor
or the Bassinet and set the mattress aside.
IMPORTANT: Test each top rail by pushing
down slightly to confirm each is rigid and
locked securely in place before use. (Fig. 4)
Rotate before
lifting
Fig. 9
2. Do not unlock top rails yet, center of floor must
be raised before top rails will unlock.
5. Place the Mattress on the floor of the Playard
with the padded side facing up. (Fig. 5)
Fig. 4
3. Rotate the center handle counter-clockwise
90 degrees and raise the center as high as the
top rails (Fig. 9). Gather the Legs and Wheels
together towards the center as close as possible
so that they nearly touch.
Latch
Tube
Tube
Release
PRESS TO
UNLOCK
6. Insert the three (3) Velcro® straps located on
the underside of the Mattress through the slots
in the floor of each end of the Playard (Fig.
6). Fasten the hook and loop straps to the
underside of the Playard floor to prevent the
Mattress from moving. (Fig. 7)
4. Locate the rail latch release in the center and
bottom side of each rail. Squeeze the lever
with two hands until the rail releases the
two tubes (Fig. 10), then push down (Fig.
11). NOTE: If the top rail(s) do not release
completely, DO NOT FORCE! Lift the center
of floor higher. Both tubes must be released
for the top rail to fold.
TOP RAIL
Fig. 10
Fig. 5
IMPORTANT: The handle located in the
center of the Playard floor MUST remain raised
(Approx. 45.7 cm or 18 inches) while locking
the side rails in place. If the center is not raised
the rails will NOT lock.
If you experience difficulty and one side of the
rail will lock but the other side will not then,
unlock the rail by squeezing the release in the
center and try again. If you still have difficulty,
contact our Customer Service Center at
1-800-328-7363 or visit us online at
Fig. 11
5. Gather four (4) corners and center all together
tightly (Fig. 12). Wrap Mattress around
Playard frame with padded side facing inward.
Secure the three (3) hook and loop straps by
feeding them through the loops on the end
of the Mattress and folding them back onto
themselves.
Fig. 6
6. Wrap Mattress around Playard frame with
padded side facing inward.
Fig. 12
7. To operate the brakes on the Wheels, press
downward on the brake levers. To release, lift
upward on the lever. (Fig. 8)
Fig. 7
7. Secure the three (3) hook and loop straps by
feeding them through the loops on the end
of the Mattress and folding them back onto
themselves. (Fig. 13)
ATTENTION:
To use as a bassinet, skip to page 8 for bassinet
installation instructions.
8. Place folded Playard into carry bag so that the
handle comes through the opening between
each side of the zipper.
Fig. 8
Fig. 13
Copyright © 2009 - 2010, Baby Trend Inc., All Rights Reserved.
Copyright © 2009 - 2010, Baby Trend Inc., All Rights Reserved.
5
6
WARNING
ASSEMBLY
ACCESSORIES
TO ASSEMBLE BASSINET
WARNING: Failure to follow these warnings and the
instructions could result in serious injury or death.
FALL HAZARD:To help prevent falls, do not use this
product when the infant begins to push up on hands and knees or
has reached the height of 25 in. (635 mm), weight of 15 lbs. (6.8 kgs)
or 4 months old, whichever comes first.
Metal Support Tubes
(2 male, 2 female)
Bassinet
SUFFOCATION HAZARD:Infants can suffocate
• In gaps between an extra pad and sides of the bassinet/cradle
• On soft bedding
ATTENTION:
Never add a mattress, pillow, comforter, or padding.
Playard must be fully assembled and securely
locked before installing or using the bassinet
feature. (See To Assemble Playard section)
Use only the pad provided by manufacturer.
Never use a water mattress with this product.
You will need to remove the mattress from the
bottom of the Playard to use inside your Bassinet.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be
placed on their back to sleep, unless otherwise advised by your physician.
• The playard, including side rails, must be fully erected prior to use. Make
sure each latch is secure.
• Strings can cause strangulation! NEVER place items with a string around
a child's neck such as hood strings or pacifier cords. NEVER suspend
strings over bassinet or attach strings to toys.
• Discontinue use of the bassinet or the changing table when child begins to
push up on hands and knees or has reached the height of 25 in. (635 mm),
weight of 15 lbs. (6.8 kgs) or 4 months old, whichever comes first.
• NEVER place product near a window where cords from blinds or drapes
can strangle a child.
• Always provide the supervision necessary for the continued safety of your
child. NEVER leave child unattended.
• NEVER use plastic shipping bags or other plastic film as mattress covers
not sold and intended for that purpose. They can cause suffocation.
1. Position the Bassinet over and down into the
fully assembled Playard. Secure in place by
pushing down firmly on each plastic support
clip until all are snapped into place (Fig. 14).
Fig. 14
Fig. 15
2. Assemble Mattress Support Tubes by
inserting the two (2) male tubes into the two
(2) female tubes (Fig. 15).
3. Insert both, assembled, Mattress Support
Tubes into the loops provided on the bottom
of the Bassinet (Fig. 16).
4. Place the Mattress into the Bassinet with the
padded side facing upward (Fig. 17)
NOTE: Fasten tabs underneath the Mattress
secure it in place.
• Use bassinet with only one child at at time.
• NEVER place a child under the bassinet.
Fig. 16
• NEVER store the bassinet in the playard while in use.
• The bassinet must be fully assembled and installed before using.
• STRANGULATION HAZARD: NEVER leave the changing table
in place when the child is in the bassinet or the playard. Always flip
changing table down while not in use.
• To prevent your child from falls and other injuries, always use safety belt
when child is on the changing table, always stay within arm's reach of
your child when using the changing table.
TO REMOVE BASSINET
1. Remove Mattress from Bassinet.
2. Remove Canopy.
3. Unsnap all clips and lift Bassinet.
• To help prevent heat build-up inside the playard and to avoid overheating
your child, when using the bassinet NEVER use an outdoor canopy.
Copyright © 2009 - 2010, Baby Trend Inc., All Rights Reserved.
Fig. 17
Copyright © 2009 - 2010, Baby Trend Inc., All Rights Reserved.
7
8
ASSEMBLY
ASSEMBLY
Contents:
PARENT ORGANIZER ASSEMBLY
(a) 1 Mobile Lower Arm
(b) 1 Mobile Arm Holder
(c) 1 Mobile Upper Curved Arm
(d) 1 Mobile Tri-shaped Arm
(e) 3 Toys (toys may vary)
(a)
(b)
Fig. 19
Diaper Stacker
1. Insert the Mobile Lower Arm (a) into the
Mobile Arm Holder (b) untill locked together
(Fig. 19).
(c)
(a)
Connect the Parent Organizer/Diaper Stacker to
the Playard by sliding the two (2) connecting clips
over an open portion of the top rail of the Playard.
(Fig. 18)
2. Insert the Mobile Upper Curved Arm (c) into
the Mobile Lower Arm (a, b) until locked
together (Fig. 20).
(b)
NOTE: The Parent Organizer/Diaper Stacker
can only be installed on open sides of the Playard
where the connecting clips can easily be attached
without interfering with other features.
Fig. 20
3. Snap the Mobile Tri-shaped Arm (d) onto the
end of the Upper Curved Arm (a, b, c)
(Fig. 21). Connect each of the three Toys (e)
to the Mobile by threading the string into the
slot at the end of each arm.
Fig. 18
(d)
MOBILE ASSEMBLY
(e)
ATTENTION:
A crib mobile is intened for visual stimulation and is not intended to be grasped by the child.
If attached to the crib or playpen, remove when baby begins to push up on hands and
knees. If so designed, mount on wall or ceiling clearly out of a standing baby's reach.
Always attach all provided fasteners (strings, straps, clamps, etc.) tightly to a crib or
playpen according to the instructions. Check frequently.
Fig. 21
4. Insert the bottom of the Mobile Arm into the
frame of the Playard (Fig. 22).
DO NOT add additional strings and straps to attach to a crib or playpen.
DO NOT attach the Mobile with child in Playard or Bassinet.
Fig. 22
(c)
(a)
(e)
(d)
(b)
Copyright © 2009 - 2010, Baby Trend Inc., All Rights Reserved.
Copyright © 2009 - 2010, Baby Trend Inc., All Rights Reserved.
9
10
|