R
AVD 400T
C
2004 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y.11788
128 - 7109
A . Welcome
H. Specification
Thank you for choosing the AVD400T DVD Player. The AVD400T is
designed to optimize the enjoyment of your favorite DVDs in the mo-
bile environment. This DVD Player is constructed to provide years of
reliable, trouble-free service. Please read this manual thoroughly prior to
operating the player and save it for future reference.
Supported media
Signal format system
DVD Video format
DVD / CD / MP3/ JPEG CD-R
NTSC/PAL
Horizontal 720 pixel,
vertical 480 pixel
1.0 Vp-p/75 Ohm
Video output
Audio output
1.2 V to 1.8 V
More than 60 dB
B. Precautions
Signal-to-noise ratio
Harmonic distortion
Dynamic range
Wow and flutter
Power source
Less than 60 dB
More than 70 dB
EXPLANATION OF GRAPHIC SYMBOLS
Beyond measurable Limits
DC 12 V Regulated
Less than 1W in stand-by mode;
and less than 12W in use
0 C (32 F) to +40 C (104 F)
-20 C (-4 F) to +60 C (140 F)
5% to 95%
Power consumption
Operating temperature
Storage temperature
Operating humidity
CAUTION: TO REDUCE THE RISK OFELECTRIC SHOCK, DO
NOT REMOVE COVER OR BACK. NO USER -SERVICEABLE
PARTS INSIDE. REFERSERVICING TO QUALIFIED PERSONNEL.
Dimensions (W x H x D)
7 x 2 x 7.3 inches
(178 x 50 x 186 mm)
3 lbs (1.6 kg)
The lighting flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
dangerous voltage within the products enclosure that may be
of sufficient magnitude to constitute risk of electric shock to
persons.
Weight
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and main-
tenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS DEVICE TO MOISTURE.
20
1
IMPORTANT NOTICE
HOW TO WATCH TV
An LCD panel and/or video monitor may be installed in a motor vehicle and
visible to the driver if the LCD panel or video monitor is used for vehicle
information, system control, rear or side observation or navigation. If the
LCD panel or video monitor is used for television reception, video or DVD
play, the LCD panel or video monitor must be installed so that these features
will only function when the vehicle is in"park" or when the vehicle's parking
brake is applied.
Press the Mode button to go to the TV mode. Active channels can be auto stored
B
by pressing STOP ( MEMORY) button.
C
Select the channels you want by pressing NEXT (CH+) button or PREVIOUS
D
(CH-) button (see page 14 remote controller picture).
Note: Channels may not be selectable if in a bad RF signal area.
An LCD panel or video monitor used for television reception, video or DVD
play that operates when the vehicle is in gear or when the parking brake is
not applied must be installed to the rear of the driver s seat where it will
not be visible, directly or indirectly, to the operator of the motor vehicle.
ADD/DEL
Use this function to delete or memorize a channel you want.
Select the channel you want by pressing the number buttons and add or
1. OBJECT AND LIQUID
Do not insert objects of any kind into the system through its openings;
do not spill or spray liquid on or into the system (this may result in a
fire or electric shock). Do not place heavy objects on the unit. To ensure
proper ventilation and proper operation, never cover or block the slots
and openings.
A
erase the channel by pressing ENTER (ADD/DEL) button.
Remote Control:
2. DISASSEMBLE
A
Do not attempt to disassemble the unit. There is a risk of electric shock
and/or exposure to Laser Radiation. Contact qualified service personnel
if your system is in need of repair.
Enter
/Add
B
C
/CH+
D
/CH-
3. CLEANING UNIT
When cleaning, make sure the system is unplugged from the power
source. Do not use any solvents or cleaning materials. Clean the DVD
player using a lightly dampened lint free cloth to wipe the unit.
2
19
4) Select Rating by using the LEFT/RIGHT buttons, press ENTER
to enter the Rating set up page.
4. DISC
Do not use irregularly shaped discs such as heart or star-shaped discs
as they may cause the unit to malfunction. Do not stick paper ,tape or
glue on the disc. Do not expose the disc to direct sunlight or heat sou-
rces. Do not touch the surface of the disc. Handle the disc by its edges.
Clean the disc by wiping the disc from the center out with a soft lint free
cleaning cloth. Remove the disc from the unit and store it in its case after
playing. Some playback operations of discs may be intentionally fixed
by software producers .The AVD400T plays discs according to the disc
contents the software producers designed therefore some playback
features may not be available. Refer to the instructions supplied with the
discs.
Load Factory
----
&. Asult
Reset
Rating Display
Select Password using the UP/DOWN buttons. For first time use
the default password 3308 to unlock the unit. Select Rating using
the UP / DOWN buttons and press ENTER to enter the submenu.
Select the rating level you desire by repeatedly pressing the ENTER
button .Use the UP button to return to Password and input either
the default password or any new 4 digit password and press ENTER.
5. Powering the DVD Player
This system MUST be powered from switched (Accessory) power as
indicated on the marking label. Power should be applied to the unit when
the ignition key is in the Run and/or Accessory position. Use only the
supplied power cable provided with this set to avoid electric hazards.
6. Operation
Rating:1.Kid Safe 2.G 3.PG 4.PG-13
5.PG-R 6.R 7.NC-17 8.Adult
When the temperature rises dramatically from a very low temperature,
moisture may condense inside the AVD400T and cause the DVD player
to malfunction. If the AVD400T does not operate properly under these
conditions leave the AVD400T turned on for at least 30 minutes for the
moisture to evaporate.
NOTE: For 1st time use the default password is 3308.
NOTE: The Default Password is 3308. This password is always
effective even after you have selected your own password and
changed it. To avoid the possibility of others using the default
password to set the parental level and change the password, you
can record this default password in another area and delete it
from this manual. Some discs can be limited depending on the
age of users while some discs can not.
Restore Default: To restore all of the options to the default settings
select RESTORE DEFAULT using the UP/DOWN buttons and
press ENTER . This will return all of the settings except parental to
the default settings.
18
3
Lpcm 48k DS Display
C. Contents
1. 1 Main Unit
b. Select ' LPCM ' using the UP/DOWN buttons, then press ENTER
to enter the submenu. Select the digital output you desire using the
UP/DOWN buttons, then press ENTER to confirm the setting.
2. 1 Remote control with one Battery (CR2025)
3. 1 12VDC Power Harness
4. 2 Brackets with 4 Screws
5. 1 Remote IR Receiver
6. 1 AV cable (RCA to RCA)
Language
Video
Audio
Rating
Digital out
Lpcm 48k DS
RAW
Off
Off
On
7. 1 AV cable (1/8 to RCA)
8. 1 Owner's Manual
9. 4 Stick-on Rubber Feet
1
9
2
3
4
5
6
7
8
D. Controls
Main Unit (Refer to Figure 1)
1. Power Button
2. Previous Button
12
10
11
18
3. Next Button
4. Mode Button
17
5. Remote Control Sensor
6. Stop /Play /Pause Button
7. A/V 2Audio Input Jack
8. A/V 2 Video Input Jack
9. Eject Button
16
15
14
13
19
10. IR Input
11.A/V 1 Input Jacks
12. Digital Audio Output
13. Audio R Output Jack
14. Audio L Output Jack
15. Video Output Jack
16. S-Video Output Jack
Figure1
17. DC In/Out 12V Power Supply Connector
18. DC In/Out 12V Power Supply Connector
19. TV-RF Input Jack
4
17
b. Select TV System using the UP/DOWN buttons, then press ENTER
to enter the submenu. Select the TV System you desire using the UP/
DOWN buttons, then press ENTER to confirm the setting.
E. Remote Control View (Refer to Figure 2)
Language
Video
Audio
Rating
1) MODE Button
TV Shape
Wide
2) POWER Button
3) MENU Button
4) UP/DOWN/
TV System
NTSC
NTSC
PAL
Auto
LEFT/RIGHT Button
5) ENTER/PLAY Button
6) VOLUME +/- Buttons
Enter
/Add
TV System Display
3) Select AUDIO using the LEFT/RIGHT buttons, press ENTER to enter
the AUDIO setup page.
7) NUMERIC KEYPAD
8) 10+ Button
9) TITLE Button
/CH+
/CH-
10) AUDIO Button
11) REPEAT Button
Language
Video
Audio
Rating
Digital out
Lpcm 48k DS
RAW
Off
Off
On
12) SUBTITLE Button
13) DISPLAY Button
14) EJECT Button
15) SETUP Button
16) PAUSE/Step Button
17) STOP/Memory Button
18) NEXT/Channel Up Button
19) PREVIOUS/Channel Down Button
20) SCAN FORWARD Button
21) SCAN REVERSE Button
22) MUTE Button
AUDIO Display Menu
a. Select Digital out using the UP/DOWN buttons, then press ENTER to
enter the submenu. Select the digital output you desire using the UP /
DOWN buttons, then press ENTER to confirm the setting.
Language
Video
Audio
Rating
Figure 2
23) GOTO Button
24) ZOOM Button
25) A-B REPEAT Button
26) ANGLE Button
27) SLOW Button
Digital out
Lpcm 48k DS
RAW
Off
PCM
RAW
AC3 Display Menu
16
5
F. Connections
2) Select Video by using the LEFT/RIGHT buttons, press ENTER
to enter the Video set up page.
White Audio In
Red Audio In
Language
Video
Audio
Rating
Yellow Video In
12DC
IN/OUT
Remote control
receiver
TV Shape
Wide
Normal/PS
Normal/LB
Wide
TV System
NTSC
S-video out
Digital Out
Video Display
TV ANTENNA
a. Select TV Shape using the UP / DOWN buttons, then press
ENTER to enter the submenu. Select the TV shape you desire
using the UP/DOWN buttons, then press ENTER to confirm the
setting.
Yellow Video out
Red Audio out
(GND)Black
(ACC+)Red
White Audio out
Language
Video
Audio
Rating
TV Shape
Wide
Normal/PS
Normal/LB
Wide
Figure 3
1. Powering your DVD Player ( Refer to Figure 3)
TV System
NTSC
Connect the black wire (-) to the vehicle ground. Connect the red
wire (+) to a switched (Accessory) 12VDC source. Plug the other
end into the 12VDC input jack on the back of the unit.
2. Remote IR Receiver ( Refer to Figure 3)
Plug the 1/8 plug on the remote IR cable into the IR IN jack on
the back of the DVD player. Place the IR receiver anywhere in the
vehicle to allow remote control from any location.
3. Connecting to a Monitor
TV Shape Display
* Normal/PS: When the player is connected to a normal TV, and a
wide picture is shown on the full screen.
a. Match the color - coded plugs to the A/V OUTPUT jacks on the
back of the DVD Player A/V OUTPUT jacks: Yellow (video) to
Yellow, White (left audio) to White, and Red (right audio) to Red.
4. Connecting an External Video Source
* Normal/LB: When the player is connected to a normal TV, and a
wide picture is shown on the screen with a black strip at both the
top and bottom of the screen.
* Wide: When the player is connected to a wide screen TV, a wide
picture is shown on the full screen.
To connect a video game or another audio/video source, plug the
A/V cable into either the A/V input jacks on the front or rear of the
DVD player.
6
15
b. Select Subtitle using the UP/DOWN buttons, then press ENTER
to enter the submenu. Select the Subtitle language you desire
using the UP/DOWN buttons, then press ENTER to confirm the
setting.
G. Playing
After connecting power to the unit, press the power button on the main unit
momentarily. Insert the disc into the slot on the front of the unit, the unit will
load the disc and start playing automatically: If there is a disc inside the unit,
press the POWER button, the unit will start playing automatically.
Language
Video
Audio
Rating
1. BASIC OPERATION
OSD Menu
Subtitle
Audio
English
English
English
English
English
Chinese
French
Spanish
German
Dutch
Turn the unit on/off
Eject/load the disc
POWER
EJECT
PLAY
DVD Menu
Start Play/Execute item or setting
Play at 1/2, 1/4, 1/6 or 1/7 times speed
Still Picture
(1 time) Stop at the present playing point /
(2 times) Stop playing
Go to the next chapter, track or scene during
play back
Go back to the preceding chapter, track or
scene during play back
Scan forward at 2, 4, 8 or 20 times normal
speed
Scan backward at 2, 4, 8 or 20 times normal
speed
Used for Menu Navigation
Execute item or setting
Select item or setting
Auto
Off
SLOW
PAUSE
STOP
Subtitle Display
c. Select Audio using the UP/DOWN buttons, then press ENTER
to enter the submenu. Select the audio language you desire using
the UP/DOWN buttons, then press ENTER to confirm the setting.
NEXT
PREVIOUS
Language
Video
Audio
Rating
FAST FORWARD
FAST REVERSE
OSD Menu
Subtitle
Audio
English
English
English
English
English
Chinese
French
Spanish
German
Dutch
DVD Menu
UP/DOWN/LEFT/RIGHT
ENTER
NUMBERS
RETURN
MENU
Return
Display the root menu of the disc
Repeat playing title, chapter, or track
Display information (title, chapter, track, time,
etc.).
Change the angles of a scene
Select the subtitle language
Select the audio language
Enlarge an image to 2, 3, or 4 times the
original
Audio Display
REPEAT
DISPLAY
d. Select DVD Menu using the UP/DOWN buttons, then press ENTER
to enter the submenu. Select the DISC Menu language you desire
using the UP/DOWN buttons, then press ENTER to confirm the
setting.
ANGLE
SUBTITLE
AUDIO
Language
Video
Audio
Rating
ZOOM
OSD Menu
Subtitle
Audio
English
English
English
English
English
Chinese
French
Spanish
German
Dutch
For DVD playback Setup press stop and then
press Setup to select and set items, and exit
the setup menu.
SETUP
DVD Menu
DVD Menu Display
14
7
12. SETUP
2. MENU
Press SETUP to display the Main screen of the SETUP Menu on
the screen. Press SETUP again to exit the SETUP Menu and the
unit will resume last playback mode.
A DVD is divided into sections called titles and chapters. When you play
a DVD, a root menu of the disc will appear on the screen of your TV or
Monitor. Contents of the menu will vary depending on the disc content.
Press MENU during playback to display the main menu. Some DVDs
only allow you to select disc playback options using the DVD root menu.
3. DISPLAY
Language
Video
Audio
Rating
1) Display mode
During playback press DISPLAY once to display items 5, and 7. Press
DISPLAY twice to display the current disc playback information. Press
display again to remove the display.
1
2 3
4
5
6
7
Main SETUP Menu Screen
1) Select language using the LEFT/RIGHT buttons, press ENTER to
enter the LANGUAGE setup page.
DVD
00:00:35 00:03:53
1 / 1
8
9
Title 1/1
Audio
Subtitle
Chapter 1 / 8 Angle
10
1/2
1/2 CHI
6Ch ENG
Language
Video
Audio
Rating
11
12
Bitrate 8.448 Mbps
OSD Menu
Subtitle
Audio
English
English
English
English
English
Francais
Espa~nol
DVD Menu
Deutsch
17
13 14
15
16
Nederlands
Display Mode
Language Display Menu
a. Select OSD Menu using the UP/DOWN buttons, then press
ENTER to enter the submenu. Select the OSD language you desire
using the UP/DOWN buttons, then press ENTER to confirm the
setting.
1. The type of disc.
11. The number of total audio
languages.
2. The number of current title.
3. The number of total titles.
4. The number of current chapter.
5. The elapsed time of title.
6. The number of total chapters.
7. The remaining time of title.
12. The number of current subtitle
language.
Language
Video
Audio
Rating
13. The number of total subtitle
languages.
14. Current subtitle language.
OSD Menu
Subtitle
Audio
English
English
English
English
English
Francais
Espa~nol
8. The number of the current angle. 15. Dolby audio mode.
DVD Menu
Deutsch
9. The number of total angles.
10. The number of the current audio 17. Current Bitrate
language.
16. Current audio language selected.
Nederlands
OSD Display Menu
8
13
USING THE REPEAT FEATURE
The default mode for the Repeat feature is OFF. Pressing REPEAT
consecutively changes the repeat options:
4) ANGLE
During playback press ANGLE to change the current angle of discs
containing multi-angles. (You can see item 8 in the display change) If
the disc has only one angle, you will see on the screen when pressing
ANGLE indicating that no other angles are available.
5) SUBTITLE
Repeat Single (repeat playback of a song)
Repeat All (repeat playback of the entire folder)
Off (normal playback)
During disc playback press SUBTITLE* to select the desired subtitle
language. (You can see item 14 change)
Pressing REPEAT a 3rd time will resume normal playback. As you toggle
through the options, the repeat option changes. Selected repeat option
loops repeatedly until you turn it off.
6) AUDIO
During disc playback press AUDIO* to select the desired audio language.
(You can see item 10 in Picture 1 change) *NOTE: Some DVD's only
allow access to these functions through the DVD menu.
7) ZOOM
NOTICE
DVD
00:00:35 00:03:53
Title 1/1
Audio
Subtitle
Chapter 1 / 8 Angle
1/2
1/2 CHI
1 / 1
6Ch ENG
Sign in front of a file name indicates that this is a folder, not
a Mp3 file.
Bitrate 8.448 Mbps
Mp3
Sign in front of a file name indicates that this is a MP3 file.
During MP3 playback, you cannot access ' PLAY MODE ', folders
or songs.
2
Zoom in Display Mode
11. Playing a JPEG file
1) Insert the JPEG Disc into tray.
2
2) You can preview the JPEG file by pressing the MENU Button.
3) Press PLAY to playback the JPEGs in order.
4) Press PAUSE to STOP on a picture.
Zoom Display
During playback press ' ZOOM ' to enlarge the picture by 1x, 2x or 3X
with the current zoom multiple displayed.
DVD
00:00:35 00:03:53
1 / 1
8) REPEAT
Title 1/1
Audio
Subtitle
Chapter 1 / 8 Angle
1/2
1/2 CHI
6Ch ENG
Bitrate 8.448 Mbps
Repeat Chapter
12
9
As you toggle through the options, the repeat option changes. The selected
repeat option loops repeatedly until its turned off.
10. PLAYING MP3 DISCS
Repeat Chapter
MP3 is a digital audio format. An audio CD-quality song is compressed
into the MP3 format with no significant loss of audio quality. CD-R /RW
discs that have been encoded in MP3 format are compatible with this
device.
Repeat Display
Insert an MP3 Disc, the DVD player will initialize the disc and the
directory (folder) will be shown on the monitor screen.
During playback press Repeat once to repeatedly play the current
chapter, press a 2nd time to repeat the current title, press a 3rd time and
the repeat function is cancelled and normal playback resumes. Repeat
mode sequence : Repeat Chapter/Repeat Title/Off.
CD-R
MENU
ROOT
0
--
9. PLAYING AUDIO CDS
Track 01
Track 02
Track 03
Track 04
Track 05
Track 06
--
When playing an audio CD the display will automatically display the disc
playback information. The options below show you what information is
displayed. Press the DISPLAY button to remove the display.
1. The current track.
2. The number of total tracks.
3. Playing time of the disc.
4. Remaining time of the disc.
Mode Folder Normal
MENU Screen Display
CD
Track 1 / 18
00:01:58
01:12:54
When an MP3 disc is inserted into the unit, the menu screen appears
automatically. You can use the menu screen to change folders and songs.
The system plays the songs in the order they were recorded onto the disc.
1
2
3
4
1. Press the
the left side of the screen.
or
button to choose a folder from the folder list on
Display in Playing CD
USING THE REPEAT FEATURE
2. Press ENTER to select the highlighted folder. All songs available
under the selected folder will be listed.
3. Use
or
ENTER to play the selected song.
button to choose a song from the list then press
The default mode for the Repeat feature is OFF. Pressing REPEAT
consecutively changes the repeat options:
Repeat Single- repeats the track that is playing.
Repeat All- repeats the disc that is playing.
Off
Use the ( NEXT )button to move to the next song. Press the
(PREVIOUS) button to move to the beginning of the song.
10
11
|