™
TTD-2400
Professional Turntable
USER INSTRUCTIONS
American Audio
4295 Charter St.
Los Angeles Ca. 90058
Revised 4/05
ELECTRICAL SAFETY PRECAUTIONS
I. Heat - The turntable should be situated
away from heat sources such as radiators, heat
registers, stoves, or other appliances (including
amplifiers) that produce heat.
WARNING: TO PREVENT FIRE OR ELECTRIC
SHOCK HAZARD, DO NOT EXPOSE THIS
UNIT TO RAIN, LIQUIDS, OR MOISTURE
2. Do not let insecticides, benzene, or thinner
come in contact with the surface of the unit.
3. Never disassemble or modify your unit in
any way, doing so will void your manufactures
warranty.
CAUTION: TO PREVENT ELECTRIC SHOCK
DO NOT USE THIS (POLARIZED) PLUG
WITH AN EXTENSION CORD, RECEPTACLE,
OR OTHER TYPE OF ELECTRICAL OUTLET
UNLESS THE WIDE BLADES CAN BE
CAREFULLY INSERTED INTO A MATCHING
WIDE SLOT.
4. Never plug this unit in to a dimmer pack
5. Do not attempt to operate this unit if it
becomes damaged in any way.
6. This unit is intended for indoor use only,
use of this product outdoors voids all warran-
ties.
ATTENTION: POUR PREVENIR LES CHOCS
ELECTRIQUES NE PAS UTILISER CETTE
FICHE POLARISEE AVEC UN PROLON-
GATEUR, UNE PRISE DE COURANT OU
UNE AUTRE SORTIE DE COURANT, SAUF
SI LES LAMES PEUVENT ETRE INSEREES A
FOND SANS EN LAISSER AUCUNE PARTIE A
DECOUVERT.
7. Always mount this unit in safe and stable
matter.
8. Disconnect from main power before making
any type of connection.
9. Cleaning - The turntable should be cleaned
only as recommended by the manufacturer.
Use a soft cloth to wipe down the outside of the
unit. For stubborn stains moisten a soft cloth
with class cleaner or other mild detergent to
wipe away any stains. Use a soft cloth to wipe
any residual cleaner. Never use volatile cleaners
such as benzene, solvent, or thinner to clean
your unit, these cleaners will damage the units
surface.
The serial and model number for this unit is
located on the rear panel. Please write down
the numbers here and retain for future refer-
ence.
Model No.______TTD-2400_______________
Serial No._____________________________
CAUTION:
1. Handle the power supply cord carefully. Do
not damage or deform; it may cause
electric shock or malfunction when used.
Hold plug attachment when removing from
wall outlet. Do not pull on the cord.
2. To avoid electric shock, do not open the
top cover when the unit is plugged in. If
problems occur with the unit, call American
Audio® customer support.
Purchase Notes:
Date of Purchase_______________________
Dealer Name__________________________
Dealer Address_________________________
_________________________________________
Dealer Phone_____________________________
3. Do not place metal objects or spill liquid
inside or on the turntable. Electric shock
or malfunction may occur.
©American Audio®
-
-
TTD-2400™ Instruction Manual Page 4
ELECTRICAL SAFETY PRECAUTIONS
ELECTRICAL PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product'senclosurethatmaybeofsufficientmagnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER (OR BACK).
THERE ARE NO USER SERVICEABLE PARTS
INSIDE REFER SERVICE TO YOUR AUTHORIZED
AMERICAN AUDIO® SERVICE TECHNICIAN.
IMPORTANT SAFETY INSTRUCTIONS
OBJECT AND LIQUID ENTRY - Never push objects of
READ INSTRUCTIONS — All the safety and operating
GROUNDING OR POLARIZATION
instructions should be read before the product is
operated.
•
Ifthisproductisequippedwithapolarizedalternating
current line plug (a plug having one blade wider than
theother), itwillfitintotheoutlet onlyoneway. This
isasafetyfeature.Ifyouareunabletoinserttheplug
fullyintotheoutlet, tryreversingtheplug. Iftheplug
should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
any kind into this product through openings as they
may touch dangerous voltage points or short-out
parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
RETAIN INSTRUCTIONS — The safety and operating
instructionsshouldberetainedforfuturereference.
HEED WARNINGS — All warnings on the product and
in the operating instructions should be adhered to.
FOLLOW INSTRUCTIONS — All operating and use
instructions should be followed.
SERVICING — Do not attempt to service this product
yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
CLEANING — The product should be cleaned only with
a polishing cloth or a soft dry cloth. Never clean with
furniture wax, benzine, insecticides or other volatile
liquids since they may corrode the cabinet.
•
If this product is equipped with
a
three-wire
DAMAGEREQUIRINGSERVICE - Unplugthisproduct
from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
groundingtypeplug,aplughavingathird(grounding)
pin, itwillonlyfitintoagroundingtypepoweroutlet.
Thisisasafetyfeature.Ifyouareunabletoinsertthe
plug into the outlet, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the grounding type plug.
•
•
When the power-supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into
the product.
ATTACHMENTS
—
Do not use attachments not
recommendedbytheproductmanufacturerasthey
may cause hazards.
WATER AND MOISTURE — Do not use this product
near water — for example, near a bathtub, wash
bowl,kitchensink,orlaundrytub;inawetbasement;
or near a swimming pool; and the like.
ACCESSORIES — Do not place this product on an
unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child or
adult, and serious damage to the product. Use only
•
•
If the product has been exposed to rain or water.
Iftheproductdoesnotoperatenormallybyfollowing
theoperatinginstructions.Adjustonlythosecontrols
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its
normal operation.
POWER-CORD PROTECTION - Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to cords at
plugs,conveniencereceptacles,andthepointwhere
they exit from the product.
OUTDOOR ANTENNA GROUNDING — If an outside
antennaorcablesystemisconnectedtotheproduct,
be sure the antenna or cable system is grounded so
astoprovidesomeprotectionagainstvoltagesurges
andbuilt-upstaticcharges.Article810oftheNational
ElectricalCode,ANSI/NFPA70,providesinformation
with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit,
connection to grounding electrodes, and
requirementsforthegroundingelectrode.SeeFigure
A.
LIGHTNING — For added protection for this product
duringalightningstorm,orwhenitisleftunattended
and unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product
due to lightning and power-line surges.
POWER LINES —An outside antenna system should
notbelocatedinthevicinityofoverheadpowerlines
or other electric light or power circuits, or where it
can fall into such power lines or circuits. When
installing an outside antenna system, extreme care
should be taken to keep from touching such power
lines or circuits as contact with them might be fatal.
OVERLOADING — Do not overload wall outlets,
extensioncords,orintegralconveniencereceptacles
as this can result in a risk of fire or electric shock.
•
•
If the product has been dropped or damaged in any
way.
When the product exhibits a distinct change in
performance — this indicates a need for service.
with
a
cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with
the product. Any mounting of the product should
follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the
manufacturer.
REPLACEMENT PARTS -- When replacement parts
arerequired,besuretheservicetechnicianhasused
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorizedsubstitutionsmayresultinfire,electric
shock, or other hazards.
SAFETY CHECK - Upon completion of any service or
repairs to this product, ask the service technician to
performsafetycheckstodeterminethattheproduct
is in proper operating condition.
WALL OR CEILING MOUNTING — The product should
not be mounted to a wall or ceiling.
HEAT —The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce
heat.
CART — A product and cart combination should be
moved with care. Quick stops, excessive force, and
uneven surfaces may cause the product and cart
combination to overturn.
VENTILATION — Slots and openings in the cabinet are
provided for ventilation and to ensure reliable
operation of the product and to protect it from
overheating, and these openings must not be
blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug,
or other similar surface. This product should not be
placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
POWER SOURCES —This product should be operated
only from the type of power source indicated on the
marking label. If you are not sure of the type of
power supply to your home, consult your product
dealer or local power company.
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
LOCATION – The appliance should be installed in a
stable location.
NONUSE PERIODS – The power cord of the appliance
should be unplugged from the outlet when left un-
used for a long period of time.
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Fig. A
NEC — NATIONAL ELECTRICAL CODE
©American Audio®
-
-
TTD-2400™ Instruction Manual Page 5
PRODUCT INFORMATION
Please carefully read and understand the
instructions in this manual thoroughly before
attempting to operate this unit. These instruc-
tions contain important safety information
regarding the use and maintenance of this unit.
Take special care to follow all warning symbols
and labels both on the unit and printed in this
manual. Also, Please keep this manual with the
unit, for future reference.
Customer Support: American Audio® pro-
vides a toll free customer support line, to pro-
vide set up help and to answer any question
should you encounter problems during your
set up or initial operation. You may also visit us
comments or suggestions. For service related
issue please contact American Audio®. Service
Hours are Monday through Friday 9:00 a.m. to
5:00 p.m. Pacific Standard Time.
LINE VOLTAGE SELECTION
Voice:
(800) 322-6337
Fax: (323) 582-2610
• The desired voltage may be set with the
VOLTAGE SELECTOR switch, located
under the platter. (use a flat head screw
driver).
E-mail:
To purchase parts online visit
• Do not force the VOLTAGE SELECTOR
switch as this may cause damage
• If the VOLTAGE SELECTOR switch does
not move smoothly, please contact a quali-
fied service technician.
Warning! To prevent or reduce the risk of
electrical shock or fire, do not expose this unit
to rain or moisture.
Caution! There are no user serviceable parts
inside this unit. Do not attempt any repairs
yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may
require service please contact customer sup-
port. Please do not return to your dealer with-
out first contacting customer support.
E
T
A
K
2
T
N A
110V-120V
220V-240V
119V
The shipping carton and packing materi-
als are constructed of recyclable material,
please recycle when ever possible.
0
Direct-Drive Professional Turntable
230V
Features:
WARRANTY REGISTRATION
• All Metal Tone Arm
The TTD-2400™ carries a ONE year (365 days)
limited warranty. This warranty covers parts
and labor. Please fill out the enclosed warranty
card to validate your purchase and warranty. All
returned service items whether under warranty
or not, must be freight pre-paid and accom-
pany a return authorization (R.A.) number. If
the unit is under warranty, you must provide a
copy of your proof of purchase invoice. Please
contact American Audio® customer support at
(800) 322-6337 for a R.A. number. All package
not displaying a R.A. number on the outside of
the package will be returned to the shipper.
• Platter Start/Stop Button
• 2 Speeds (33 & 45 RPM)
• 0% Pitch Quartz Lock
• Extra Stylus Holder
• Adjustable Feet for Leveling
• Adjustable Pitch Ranges +/- 10%
• Anti-Skating Tone Arm Adjustment
• Tone Arm Holder with Lock
• Built-in 45 Adapter& Holder
• User Selectable Operating Voltage
(115v~60Hz or 230v~50Hz)
©American Audio®
-
-
TTD-2400™ Instruction Manual Page 6
QUICK-START
Turntable Quick-Start:
1. Changing Platter Speed
Use the RPM selectors (10 & 11) to change the platter speeds. The 33-rpm (10) and 45-rpm (11) speed
selectors change the platter rotation respectively.
2. Starting and Stopping the Platter
Use the START/STOP BUTTON (6) to switch back and forth between platter rotation and pause
modes.
3. Pitch Control
1. The pitch adjustment is a fine adjustment to the platter's RPMs.
2. The pitch adjustment is variable and may be adjusted between -10% and +10% of the platter
selected speed.
3. The pitch is changed by sliding the Pitch Slider (12) in an up and down motion.
4. The STROBE INDICATORS (2) on the rim of the PLATTER (20) can be used to visual approxi-
mate the platter pitch. These indicators are lit by the STROBE INDICATOR PILOT LAMP (4) as
they pass by the POWER SWITCH (5). At different pitch levels each row of STROBE INDICATORS
(2) may appear stand still.
Note: The use of heavy fluorescent lighting directly above the turntable will defeat the STROBE
LAMP PILOT LAMP (4) affect indicator accuracy.
Product Service:
1. Clean the stylus periodically with a soft brush to prevent the accumulation of dust.
2. When sound becomes distorted or noisy, check the stylus. If the stylus is worn out, replace
it with a new one.
3. From time to time, the dust cover and turntable cabinet should be wiped down with a soft,
dry cloth.
4. Volatile materials should not be used, such as: alcohol, thinner, benzine etc. They may remove
the paint or damage the luster.
©American Audio®
-
-
TTD-2400™ Instruction Manual Page 6
SET-UP
Some assembly required before you can begin to use your new TTD-2400. Please follow the
assembly instruction below before attempting to use you new turntable.
ASSEMBLY:
Before you begin assembly please be sure all parts and accessories have arrived intact. Please use
the check list below to identify and order parts and accessories.
NOTES:
• Do not connect the AC power plug before assembly has been completed.
• Before turning the power on, make sure once again all the connections and power voltage
settings are correct. Always turn off the power when connecting or disconnecting.
• Read this manual carefully before using the unit. Be sure to store the manual in a safe place for
future reference.
• Attach a stylus cartridge to the HEADSHELL (7) before assembling the turntable unit.
Headshell Assembly:
When installing a cartridge, refer to the operating instructions of that cartridge. During installation,
attach the stylus protector to guard the stylus tip from damage.
Connect the HEADSHELL (7) lead wires to the cartridge terminals. The terminals of cartridges and the
HEADSHELL (7) lead wires are color coded. Connect each lead wire to the cartridge terminals of the
same color.
White (L+) .............……………...... Left channel +
Blue (L-) ....……………................ Left channel -
Red (R+) ..………….................... Right channel +
Green (R-) .......……………............ Right channel -
Turntable Assembly:
1. REMOVING FROM CARTON:
Carefully remove the main unit with the packing material intact from the box. Remove the packing
material once the unit has been removed from the shipping carton. Be sure to locate all the acces-
sories located in the packing material.
2. 45 ADAPTER (1):
Locate and remove the 45-rpm adapter from the packing material and place it in the 45 adapter cut
out on the top of the main unit.
3. TURNTABLE PLATTER (20):
Remove the turntable platter from the packing material and gently insert the platter into the CENTER
SPINDLE (3) on the base of the turntable unit.
4. SLIPMAT:
Remove the black slipmat from the packaging and place it on the PLATTER (20).
©American Audio®
-
-
TTD-2400™ Instruction Manual Page 7
SET-UP
5. HEADSHELL (7):
Insert the HEADSHELL (7) into the front end of the TONEARM ASSEMBLY (9). While holding
HEADSHELL (7) firmly into the front end of the tonearm assembly, turn the HEADSHELL LOCKING
NUT (8) counter-clockwise to firmly secure the HEADSHELL (7) to TONEARM ASSEMBLY (9).
HEADSHELL
TONEARM ASSEMBLY (9)
HEADSHELL LOCKING NUT (8)
6. COUNTERWEIGHT (16):
Locate and remove the tonearm COUNTERWEIGHT (16) from the packaging. Slide COUNTERWEIGHT
(16) onto the rear of the TONEARM ASSEMBLY (9). Turn it lightly and it will screw onto the rear shaft
of the tonearm.
TONEARM ASSEMBLY (9)
COUNTERWEIGHT (16)
Turntable Connections:
1. Connect the unit's stereo output leads to a receiver or mixer. The red phono terminal represents
the right output channel and the white terminal represents the left output channel.
2. The thin black wire with a spade connector is the ground lead. The ground lead must be connect
to the mixer (receiver) to avoid pops and clicks associated with magnetic pick-up system such as
turntables.
Output Leads
Mixer (Receiver)
L (White)
-----------------------------> L Channel
R (Red)
-----------------------------> R Channel
GND (Spade) ----------------------------> Ground
©American Audio®
-
-
TTD-2400™ Instruction Manual Page 8
SET-UP
3. Connect the power core to matching outlet for your area. Only connect the power cord after the
all other connections have been made.
NOTE: Be sure to connect the ground terminals firmly to the Mixer or receiver.
AMERICAN AUDIO
Phono ground lead
Stereo phono lead
Phono ground lead
Stereo phono lead
E
T
A
E
T
A
2
2
S
-
S
-
N A
N A
TTD-2400
Direct-Drive Professional Turntable
TTD-2400
Direct-Drive Professional Turntable
Turntable Installation:
1. Do not place the unit in a location where it will be exposed to direct sunlight or near any type of
heating appliance.
2. Do not place the unit in a location where there is high humidity or a lot of dust.
3. Cartridge may pick up slight sound pressure or vibrations of near by speakers. For best results,
do not install this unit too close to speakers.
4. Install this unit on a horizontal surface that is stable and vibration free.
5. The rubber feet have been specially designed to isolate the unit from excess vibration. The feet
may also be used to stabilize the main body horizontally. Adjust the height of the unit by turning the
feet in a clockwise or counter-clockwise direction.
Tonearm Balance and Stylus Pressure:
Adjustment of horizontal zero balance and stylus pressure:
1. Remove the stylus protective cover, if so equipped. Never touch the stylus tip during the adjust
ment.
2. Lower the TONEARM LEVER (13).
3. Release the tonearm clamp and release the tonearm from the arm rest.
4. Set the ANTI-SKATE (15) adjustment to zero.
5. Rotate the COUNTERWEIGHT (16) in either direction until the TONEARM (9) is perfectly balanced
©American Audio®
-
-
TTD-2400™ Instruction Manual Page 9
SET-UP
horizontally (floats freely).
6. Return the TONEARM (9) to the arm rest and lock it in place.
7. Hold the COUNTERWEIGHT (16) stationary with one hand and rotate only the stylus-pressure ring
to bring the number “0” of the ring into alignment with the center line on the tonearm rear shaft.
8. Rotate the COUNTERWEIGHT (16) clockwise until the scale value corresponding to the recom-
mended stylus pressure.
Note: The recommended stylus pressure of the optional cartridge that may have been included with
your unit is 2 grams. For all other cartridge systems please refer to the manufactures specification
included with the cartridge.
Anti-Skate:
The anti-skate adjustment prevents the TONEARM ASSEMBLY (9) from skipping across the record
from the centrifugal force that is caused spinning rotation of the PLATTER (20). The ANTI-SKATING
(15) control knob should be set to the same value as the stylus pressure. For example if your
COUNTERWEIGHT (16) is set to 2.5 grams the ANTI-SKATE (15) value should also be set to 2.5.
©American Audio®
-
-
TTD-2400™ Instruction Manual Page 10
CONTROLS AND FUNCTIONS
20
1918
17
1
16
15
3
E
T
2
S
-
N
1
2
3
14
13
12
4
5
6
TTD-2400Direct-Drive Professional rntable
7 8 9
10 11
This adapter allows you to play standard 7” EP vinyl
records with large center holes. Place the adapter on
the CENTER SPINDLE (3) 7" records.
1. EP ADAPTER -
The PLATTER (20) has four rows of indicators. These
indicators are used to visually detail various stages of
pitch. The indicators are illuminated by the STROBE
INDICATOR PILOT LAMP (4). Each row may appear to
stand still at different pitch levels.
2. STROBE INDICATORS -
Note: The use of heavy fluorescent lighting directly
above the turntable will defeat the STROBE LAMP
PILOT LAMP (4) affect indicator accuracy.
This spindle holds the turntable PLATTER (20) and
3. CENTER SPINDLE -
records stable and centered.
This is lamp specially designed to pulse a beam of
light at the STROBE INDICATORS (2) on the turntable
PLATTER (20). This will give the illusion that indicators
are not spinning at certain speeds.
4. STROBE INDICATOR PILOT LAMP -
This is a rotary power switch. To turn main power on
turn the switch in a clockwise direction. To turn main
power off turn the switch in counter-clockwise direc-
tion.
5. POWER SWITCH -
©American Audio®
-
-
TTD-2400™ Instruction Manual Page 11
CONTROLS AND FUNCTIONS
6. START/STOP BUTTON -
This over sized push button controls platter motion.
When the unit is turned on the platter will not auto-
matically begin to spin. Pressing the button once will
engage the high torque motor and spin the platter,
pressing this again will stop the platter.
The included HEADSHELL (7) is used to connect your
7. STYLUS HEADSHELL -
stylus with the tone arm.
After attaching the headshell to the tonearm, this
locking nut will securely hold the headshell to the
tonearm.
8. HEADSHELL LOCKING NUT -
The tonearm is the mechanism that holds the HEAD-
SHELL (7) and stylus allowing it to glide across a
record.
9. S-SHAPED TONE ARM -
Engaging this button will rotate the platter at 33 revo-
lutions per a minute (RPMs). A function LED will glow
when this function is activated.
10. 33-RPM SPEED SELECTOR BUTTON -
11. 45-RPM SPEED SELECTOR BUTTONS -
12. PITCH ADJUST SLIDER -
Engaging this button will rotate the platter at 45 RPMs.
A function LED will glow when this function is acti-
vated.
This slider is used to adjust the playback pitch per-
centage (platter speed). Use this slider to match the
BPM’s of this unit to that of another music source.
This lever is used to safely elevates the tone arm
above a record surface without endangering a records
surface.
13. TONEARM LEVER -
Use this rest to safely hold the tonearm in position
during non use and transportation.
14. TONEARM CLAMP AND REST -
15. ANTI-SKATE CONTROL -
The anti-skate applies inward force to the tonearm
to prevent outward skipping across the record due
to the centrifugal force cause by platter rotation. The
antiskate value should be equally to that of the stylus
counterweight pressure (see counterweight 16).
The counterweight adjustment applies the proper
downward pressure on the stylus.
16. COUNTERWEIGHT -
This cut out has been designed to safely store an
extra stylus headshell.
17. EXTRA STYLUS HOLDER -
18. RCA OUTPUT JACKS -
These jacks are used to send a low voltage "phono"
level output signal to a mixers "phono" input jacks.
Turntables should only be connected to “Phono”
inputs on a mixer. The red colored RCA jack repre-
sents the right channel input and the white repre-
sents the left channel input.
©American Audio®
-
-
TTD-2400™ Instruction Manual Page 12
CONTROLS AND FUNCTIONS
This ground connection is designed to reduce the
humming and popping noises associated with mag-
netic phono cartridges. Be sure to connect the turn-
table ground lead to any available ground terminal on
the same mixer the input signal leads are connected
to.
19. GROUND CONNECTOR -
This platter connects directly to the center spindle (3).
The platter and center spindle (3) holds a vinyl record
perfectly center. The platter also spins the record at a
consistent speed.
20. PLATTER -
©American Audio®
-
-
TTD-2400™ Instruction Manual Page 13
WARRANTY
1-YEAR LIMITED WARRANTY
A. American Audio® hereby warrants, to the original purchaser, American Audio® products to be
free of manufacturing defects in material and workmanship for a period of 1 Year (365 days) from
the date of purchase. This warranty shall be valid only if the product is purchased within the United
States of America, including possessions and territories. It is the owner’s responsibility to establish
the date and place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service, send the product only to the American Audio® factory. All shipping
charges must be pre-paid. If the requested repairs or service (including parts replacement) are
within the terms of this warranty, American Audio® will pay return shipping charges only to a desig-
nated point within the United States. If the entire instrument is sent, it must be shipped in its origi-
nal package. No accessories should be shipped with the product. If any accessories are shipped
with the product, American Audio® shall have no liability whatsoever for loss of or damage to any
such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modi-
fied in any manner which American Audio® concludes, after inspection, affects the reliability of the
product; if the product has been repaired or serviced by anyone other than the American Audio®
factory unless prior written authorization was issued to purchaser by American Audio®; if the prod-
uct is damaged because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning or peri-
odic check-up. During the period specified above, American Audio® will replace defective parts at
its expense, and will absorb all expenses for warranty service and repair labor by reason of defects
in material or workmanship. The sole responsibility of American Audio® under this warranty shall be
limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of
American Audio®. All products covered by this warranty were manufactured after January 1, 1990,
and bear identifying marks to that effect.
E. American Audio® reserves the right to make changes in design and/or improvements upon its
products without any obligation to include these changes in any products theretofore manufac-
tured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory
supplied with products described above. Except to the extent prohibited by applicable law, all
implied warranties made by American Audio® in connection with this product, including warranties
of merchantability or fitness, are limited in duration to the warranty period set forth above. And no
warranties, whether expressed or implied, including warranties of merchantability or fitness, shall
apply to this product after said period has expired. The consumer’s and or Dealer’s sole remedy
shall be such repair or replacement as is expressly provided above; and under no circumstances
shall American Audio® be liable for any loss or damage, direct or consequential, arising out of the
use of, or inability to use, this product.
G. This warranty is the only written warranty applicable to American Audio® Products and super-
sedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
©American Audio®
-
-
TTD-2400™ Instruction Manual Page 14
SPECIFICATIONS
GENERAL
Model:
American Audio® TTD-2400 - Direct Drive Phono Turntable
2-Speed Direct Drive Phono Turntable Table
17.72” (W) x 13.7” (D) x 5.4" (H)
450 (W) x 350 (D) x 139 (H) mm
Place on flat surface or mount in flat case
22 Lbs. / 9.5 Kgs
System:
Dimensions:
Installation:
Weight:
Power supply:
AC 115v~60Hz/230v~50Hz
Power consumption:
Environmental conditions:
9W
Operational Temperature: 5 to 35˚C (41 to 95˚F)
Operational Humidity: 45 to 85% RH (non-condensation)
Storage Temperature: -10 to 60˚C (4 to 140˚F)
Instruction Manual,
Accessories:
Headshell,
45 RPM Adaptor
TURNTABLE SECTION
Type:
2 Speed Fully Manual
8 Pole, 2 Phase, Brushless DC Motor
Direct Drive
Motor:
Driving Method:
Turntable Platter:
Speeds:
Wow and Flutter:
S/N Ratio:
Pitch Controls:
Starting Torque:
Braking System:
Starting Time:
Braking Time:
Time for Speed Change:
330 mm dia. Aluminum Diecast
33-1/3 and 45-rpm
Less than 0.15% WRMS (JIS WTD) with 331/3rpm
More than 50dB (DIN-B)
+/- 10%
More than 1 kgf.cm
Electronic brake
Less than 1 sec.
Less than 1 sec.
Less than 1 sec. from 33 to 45 rpm.
Less than 1 sec. from 45 to 33 rpm.
6~10 mm
High of Cue (first track):
Descend of Cue:
5 sec.
TONEARM SECTION
Type:
Static balanced straight shaped tonearm with detachable headshell
Effective Arm Length:
Overhang:
220mm
10mm
Less than 3 degree
Tracking Error Angle:
Tracking Force Adjustment Range: 3-4g
Applicable Cartridge Weight:
Anti-skating Range:
Output:
6-10g
0-7g
1.5-3.6mV at 1KHz 5cm/sec
20Hz - 20KHz
More than 15 dB
Within 2.5dB at 1KHz
2.5g
Frequency Response:
Channel Separation:
Channel Balance:
Needle Pressure range:
SPECIFICATION
DESCRIPTIONS
UNIT
dB
mv
Hz
NORMAL
2.3
LIMIT
Output Difference::
Output Level:
2.54
1.7~3.5
2.7K ,3.3K
2995~3005
0.13
1.5~3.6
2710 ,3290
2990~3010
0.15
Speed (Speed Range) +/- 10%
Speed (Center Range)
Wow and Flutter
Hz
%
dB
Channel separation
16
15
©American Audio®
-
-
TTD-2400™ Instruction Manual Page 15
©American Audio®
American DJ® Group of Companies World Headquarters:
4295 Charter Street Los Angeles, CA 90058 USA
Tel: 323-582-2650 Fax: 323-582-2610
|