SPECIAL APPLICATION
MANUAL PART NUMBER: 400-0442-006
DS801-111
INTERA® COMPUTER/COMPONENT
VIDEO+ STEREO AUDIO
TWISTED PAIR (UTP) RECEIVER
SPECIAL APPLICATION
1.4 FCC NOTICE
PRECAUTIONS / SAFETY WARNINGS
1
·
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference; and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Please read this manual carefully before using your
DS801-111. Keep this manual handy for future
reference. These safety instructions are to ensure
the long life of your DS801-111 and to prevent fire
and shock hazards. Please read them carefully and
heed all warnings.
1.1 GENERAL
·
This equipment has been tested and found to
comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference when the
·
Qualified ALTINEX service personnel or their
authorized representatives must perform all
service.
equipment is operated in
a
commercial
1.2 INSTALLATION
environment. This equipment generates, uses,
and can radiate radio frequency energy and if
not installed and used in accordance with the
instructions found herein, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.
·
To prevent fire or shock, do not expose this unit
to water or moisture. Do not place the
DS801-111 in direct sunlight, near heaters, or
heat-radiating appliances, or near any liquid.
Exposure to direct sunlight, smoke, or steam
can harm internal components.
·
·
Handle the DS801-111 carefully. Dropping or
jarring can damage the unit.
Do not pull any cables that are attached to the
DS801-111.
·
Any changes or modifications to the unit not
expressly approved by ALTINEX, Inc. could void
the user’s authority to operate the equipment.
1.3 CLEANING
·
Clean only with a dry cloth. Never use strong
detergents or solvents, such as alcohol or
thinner. Do not use a wet cloth or water to clean
the unit. Do not open the unit to clean.
400-0442-006
2
SPECIAL APPLICATION
ABOUT YOUR DS801-111
2
TECHNICAL SPECIFICATIONS
3
Specifications are subject to change.
DS801-111
Intera Twisted Pair (UTP) to Video +
Stereo Audio Receiver
FEATURES/
DS801-111
DESCRIPTION
The DS801-111 provides a means of receiving
computer video and audio signals over
Twisted Pair-type (CAT-5/6) cable when used
together with a compatible ALTINEX Twisted Pair
(UTP) video transmitter, such as the DS801-110 or
DA1930CT.
GENERAL
Inputs
Video+ Stereo Audio
Power
RJ-45 female (1)
2-pin terminal block (1)
The DS801-111 is compact and easy to use. The
DS801-111 is able to receive either computer video
or component video along with stereo audio
transmitted over the UTP cable from the
DS801-110 or an equivalent transmitter.
Output
Video
15-pin HD female (1)
3.5 mm female (1)
Stereo Audio
Compatibility
Signal Types
The DS801-111 provides both video and stereo
audio outputs. The DS801-111 offers a female
15-pin HD output for RGBHV/YPbPr signals with
native Plug & Play compatibility and a 3.5 mm jack
is used for the stereo audio output.
ALTINEX Standard for
Twisted Pair
VGA through UXGA
480p through 1080i
Video Signal
Resolutions
The unit also offers video equalization hardware for
long transmission lengths. There is also a Signal
Detect feature that shows when an input signal is
present.
VGA:
640x480@60Hz
900 ft (274 m)
Recommended Max.
Cable Lengths
Note: Measurements
made using ALTINEX
low-skew cable,
XGA: 1024x768@60Hz
700 ft (213 m)
The latest generation of Twisted Pair devices uses
an innovative, patented technology* developed by
ALTINEX. The new signal processing technology
allows transmitting and receiving fully equalized
computer video signals, stereo, and audio signals
over long distances.
SXGA: 1280x1024@60Hz
650 ft (198 m)
CB3150PV.
UXGA: 1600x1200@60Hz
600 ft (183 m)
Accessories Included
Power Adapter
(with 50 ft (15 m) cable)
* US Patent 7,065,190
+9 VDC, 500 mA
Table 1. DS801-111 General
400-0442-006
3
SPECIAL APPLICATION
MECHANICAL
Housing
DS801-111
0.036” Aluminum
0.035” Steel
ELECTRICAL
Input
DS801-111
Video/Sync/Audio Signals
ALTINEX Standard
Front Panel
Length
Video+ Stereo Audio
4.10 in (104 mm)
1.38 in (35 mm)
1.20 in (30 mm)
0.25 lb (0.11 kg)
10°C-50°C
Output
Width
Video Analog Signal
Video Sync Level
Audio Level
1.0 Vp-p max.
TTL
Height
Weight
0 dB +/- 0.5 dB at 1 KHz
T° Operating
T° Maximum
Humidity
Power Consumption
External Adapter: 9 VDC
75°C
410 mA (3.7 W) max.
90% non-condensing
38,000 hrs
Table 3. DS801-111 Electrical
MTBF (calc.)
Table 2. DS801-111 Mechanical
400-0442-006
4
SPECIAL APPLICATION
PRODUCT DESCRIPTION
4
VIDEO
EQUALIZATION
POWER/SIGNAL
PRESENT LED
VIDEO OUTPUT
AUDIO OUTPUT
4TP INPUT
POWER
400-0442-006
5
SPECIAL APPLICATION
APPLICATION DIAGRAMS
DIAGRAM 1: TYPICAL SETUPS
5
DS801-110
DS801-111
DS801-111
400-0442-006
6
SPECIAL APPLICATION
DIAGRAM 2: INTERNAL VIEW
DS801-111
POWER
2-PIN TERM. BLOCK
9 V, 500 mA
PS
LEFT
LP
LP
UNBAL.
AUDIO
STEREO
3.5mm
AUDIO
SEPARATOR
PAIR 4
RIGHT
SIGNAL
DETECT
POWER
4TP
RJ-45
V
SYNC
SEPARATOR
H
COMPUTER/
COMPONENT
VIDEO
PAIR 2
PAIR 3
PAIR 1
R/Pr
15-PIN HD
B/Pb
G/Y
H/W
EQ
400-0442-006
7
SPECIAL APPLICATION
INSTALLING YOUR DS801-111
6
OPERATION
7
Step 1. Determine the best location for the
DS801-111. Where possible, locate the
TP Transmitter as close to the video
source as possible and the DS801-111 as
close to the receiving component as
feasible.
The DS801-111 requires only one adjustment to be
made for optimal performance. The adjustment is
video equalization for long cable lengths.
7.1 VIDEO EQUALIZATION
Video equalization is provided to fine-tune the
displayed image on the remote display.
Typically, for short cable runs the equalization
will be set to near minimum.
Step 2. Apply power to the 2-pin terminal block on
the rear of the DS801-111.
The
Power/Signal Present LED should be on
and red.
Start by setting the equalization to minimum on
both units. Adjust the equalization on the
receiver first. This adjustment should at least
allow the receiving display to receive an image.
Then use the equalization on both units to
fine-tune the image for optimal quality.
Step 3. Connect the receiving display to the
output of the DS801-111 using
a
high-quality video cable.
Step 4. Connect the audio amplifier or speakers
to the audio jack on the DS801-111.
TROUBLESHOOTING GUIDE
8
Step 5. Run a UTP-type (CAT-5/CAT-5e) cable
from the 4TP INPUT on the DS801-111
Receiver to the 4TP OUTPUT on the TP
Transmitter.
We have carefully tested and have found no
problems in the supplied DS801-111. However, we
would like to offer suggestions for the following:
8.1 NO DISPLAY
NOTE: Ensure good signal transmission
by routing the cable to avoid any
sharp angles, creases, or bends.
Cause 1: The source has a problem.
Solution: Check the source and make sure
there is a signal present and all
source connections are correct. If
the source is working and there is
still no display, see Cause 2.
Step 6. Connect the TP Transmitter per its
installation instructions. In the case of the
DS801-111, when the TP signal from the
DS801-110 is applied, the Power/Signal
Present LED will turn from red to green
indicating a signal is present.
Cause 2: The path has a problem.
Solution: Connect the transmitter directly to
the receiver using a short UTP
patch cable. If the image is good,
there is a problem with the cable.
Otherwise, see Cause 3.
Step 7. The units are now operational.
Cause 3: Cable connections are incorrect.
Solution: Make sure that cables are properly
connected. Also, make sure that the
continuity and wiring are good. If
there is still no display present, see
Cause 4.
400-0442-006
8
SPECIAL APPLICATION
Cause 4: Video equalization required.
ALTINEX POLICIES
9
Solution: Adjust the VIDEO EQUALIZATION
on the DS801-111.
9.1 LIMITED WARRANTY/RETURN POLICIES
Please see the ALTINEX website at
www.altinex.com for details on warranty and
return policies.
Some monitors are very sensitive to
signal quality and this may prevent
the monitor from displaying an
image until the equalization is
adjusted. See the operation section
for adjustment details.
9.2 CONTACT INFORMATION
ALTINEX, Inc.
592 Apollo Street
Cause 5: The display has a problem.
Brea, CA 92821 USA
TEL: 714 990-2300
Solution: Make sure the display is powered
and is turned on. If there is still no
display, please call ALTINEX at
(714) 990-2300.
TOLL FREE: 1-800-ALTINEX
WEB: www.altinex.com
E-MAIL: [email protected]
8.2 NO SOUND
Cause 1: The source has a problem.
Solution: Check the source and make sure
that there is a signal present and all
source connections are correct. If
the source is working and there is
still no sound, see Cause 2.
Cause 2: The volume is too low.
Solution: Increase the gain at the source. If
there is still no sound present, see
Cause 3.
Cause 3: Cable connections are incorrect.
Solution: Make sure that cables are properly
connected. Also, make sure that the
continuity and wiring are good. If
there is still no sound, see Cause 4.
Cause 4: The receiving device has
problem.
a
Solution: Make sure the receiving device is
powered and is turned on. If there
is still no sound, please call
ALTINEX at (714) 990-2300.
400-0442-006
9
|