™
OwNERS MANUAL
Model No.
45-0382
45-0405
125 LB. PUSH
BROADCAST SPREADER
• Safety
• Assembly
• Operation
• Maintenance
• Parts
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
PRINTED IN USA
FORM NO. 49905 (REV. 11/06)
HARDwARE PACKAGE CONTENTS (Shown full size except where noted)
Key
Qty.
Description
Key
Qty.
Description
I
J
K
L
M
N
O
P
Q
1
ꢀ
1
1
1
ꢀ
1
ꢀ
1
Cotter Pin, 5/3ꢀ x ꢀ in.
Cotter Pin, 9/64 x 1-1/ꢀ in.
Cotter Pin, 1/8 x 3/4 in.
Spring
Wing Nut, 1/4-ꢀ0 Nylon
Spacer
Adjustable Stop
Handle Grip
Flow Control Lever Grip
A
B
C
D
E
F
3
8
1
1
1ꢀ
3
Hex Bolt, 1/4-ꢀ0 x ꢀ-1/ꢀ in. Long
Hex Bolt, 1/4-ꢀ0 x 1-1/ꢀ in. Long
Hex Bolt, 1/4-ꢀ0 x 3/4 in. Long
Carr. Bolt,1/4-ꢀ0 x 3/4 in. Long
Nylock Nut, 1/4-ꢀ0
Washer, 1/4 in. SS
Washer, Nylon
Washer, 5/8 ID x 1 in. OD
G
H
1
6
FULL SIZE
E
D
C
A
B
H
G
F
I
J
K
L
N
O
M
P
Q
(Not Shown Full Size)
(Not Shown Full Size)
3
ENGLISH
ASSEMBLY INSTRUCTIONS
9/64 x 1-1/2 in.
COTTER PIN (J)
5/32 x 2 in.
COTTER PIN (I)
TOOLS REQUIRED FOR ASSEMBLY
(1) Pliers
(ꢀ) 7/16 in. open or boxed end wrenches
5/8 in. FLAT
WASHER (H)
1. Removethespreader, theloosepartsandthehardware
package from the carton. Lay out parts and hardware
and identify using the illustrations on pages ꢀ and 3.
ꢀ. With the spreader resting upside down on the top of the
hopper, assemble a 5/8 in. flat washer, a spacer and
a second 5/8 in. flat washer onto each end of the axle.
See figure 1.
SPACER (N)
FIGURE 2
5/8 in. FLAT WASHER (H)
6. Install an upper handle to each lower handle using four
1/4 x 1-1/ꢀ in. bolts and nylock nuts. Do not tighten at
this time. See figure 3.
1/4-20 x 1-1/2 in.
HEX BOLT (B)
FIGURE 1
3. Place a wheel onto each end of the axle.The long end
of the hub goes to the inside. See figure 2.
4. Assemble a 5/3ꢀ x ꢀ in. cotter pin through the hole in
one wheel hub and the axle. See figure 2.
5. Place a 5/8 in. flat washer onto each end of the
axle and secure with a 9/64 x 1-1/ꢀ in. cotter pin.
See figure 2.
1/4-20 NYLOCK
NUT (E)
FIGURE 3
4
7. For the standard setup, use the holes shown in
the illustration. Other hole combinations allow
different handle heights and hopper angles. Do
not use holes in stand that are farthest apart as a
combination - flow gate may not close completely.
Attach the stand to the hopper frame tube using two
1/4 x 1-1/ꢀ in. bolts and nylock nuts. Attach the stand
to the lower handle using two 1/4 x 1-1/ꢀ in. bolts and
nylock nuts. Tighten all four bolts to secure the stand.
See figure 4.
9. Install a handle grip on each handle. See figure 6.
10. Attach the flow control lever to the bracket using one
1/4 x 3/4 in. bolt, nylon washer and nylock nut. Tighten
carefully to allow the lever to move freely. Install the
vinyl grip. See figure 6.
HANDLE
GRIP (P)
1/4-20 x 3/4 in.
HEX BOLT (C)
1/4-20 NYLOCK
NUT (E)
USE
MIDDLE
HOLE
LEVER
GRIP (Q)
1/4 in. NYLON
WASHER (G)
1/4-20 NYLOCK
LEVER
NUT (E)
FIGURE 6
1/4-20 x 1-1/2 in.
HEX BOLT (B)
USE THIS
HOLE
FIGURE 4
11. Attach the spring to the stainless steel pattern plate as
shown. Attach the opposite end of the spring to the 1/8
in. hole in the flow control rod. Rotate the end of the rod
into the flow control link. See figure 7.
8. Attach the two upper handles together with
the flow control bracket as shown using three
1/4 x ꢀ-1/ꢀ in. bolts and nylock nuts. Do not tighten
two bolts in flow control bracket. Tighten third bolt in
upper handles. See figure 5.
1/4-20 x 2-1/2 in.
HEX BOLT (A)
SPRING
ANCHOR
HOLE
SPRING (L)
1/8 in. HOLE
FLOW
CONTROL
LINK
1/4 in. WASHER (F)
1/4-20 NYLOCK
NUT (E)
FIGURE 5
FIGURE 7
5
12. Insert the end of the flow control rod through the slot in
the flow control mounting bracket and through the hole
in the flow control lever. Secure with a 1/8 in. x 3/4 in.
cotter pin. See figure 8.
14. Adjust the position of the flow control mounting bracket
(figures 10 and 11):
a. Set the adjustable stop at “5.” Latch the flow control
lever against the stop. Verify that the closure plate
has opened about halfway. See figure 10.
1/8 x 3/4 in.
COTTER PIN (K)
b. Ifclosureplateis notopenhalfway,adjusttheposition
of the flow control mounting bracket until the closure
plateisopenabouthalfwayat“5”andstillclosedwhen
the lever is in the “OFF” position. Carefully tighten
the 1/4 in. nylock nuts. Do not deform the slots in the
flow control mounting bracket.
c. Push the flow control lever to the “OFF” position
and ensure the closure plate closes completely.
See figure 11.
FLOW
CONTROL
ROD
FLOW
CONTROL
LEVER
POSITION 5
ADJUSTABLE
STOP
FIGURE 8
1/4 in. NYLOCK NUTS
13. Install the adjustable stop on the slot in the top of
the flow control mounting bracket. Secure with the
1/4 in. x 3/4 in. carriage bolt, a nylon washer, a 1/4 in.
flat washer and the nylon wing nut. See figure 9.
FIGURE 10
1/4-20 WING NUT (M)
1/4 in. WASHER (F)
ADJUSTABLE
STOP
OFF
ADJUSTABLE
STOP (O)
1/4-20 x 3/4 in.
CARRIAGE BOLT (D)
FIGURE 11
FIGURE 9
6
15. Place the hopper screen down into the hopper, sliding
the ends into the clips in the hopper. The screen helps
break up clumpy material and prevents large clumps
from reaching the bottom of the hopper and clogging
the opening. See figure 12.
1. To adjust the flow to be heavier to the left side,
tighten the thumbscrew so the plate is pushed inward.
See figure 13
2. To adjust the flow to be heavier to the right side,
loosen the thumbscrew so the plate is pulled outwards.
See figure 13
HOPPER
SCREEN
THUMB SCREW
FIGURE 13
FIGURE 12
16. Lubricate the spreader following the instructions in the
USINGYOUR SPREADER
MAINTENANCE section on page 9.
The use of powdered lawn chemicals is not recommended,
due to difficulty in obtaining a satisfactory or consistent
broadcast pattern.
OPERATION
1. Determine approximate square footage of area to be
covered and estimate amount of material required.
HOw TO USEYOUR SPREADER
SETTING THE FLOw CONTROL
2. Beforefillingthehopper,makesuretheflowcontrollever
(Refer to figure 10 on page 6.)
is in the “OFF” position and the closure plate is shut.
3. Break up any lumpy fertilizer as you fill the hopper.
1. Loosen the nylon wing nut, set the adjustable stop to
the desired flow rate setting and retighten the wing nut.
The higher the setting number, the wider the opening
in the bottom of the hopper.
4. Set the adjustable stop with the flow control lever still
in the “OFF” position. Refer to the Application Chart on
page 8 and to the instructions on the fertilizer bag to
select the proper flow rate setting.
ꢀ. Refer to the Application Chart on page 8 and to the
instructions on the fertilizer bag to select the proper
flow rate setting.
5. The Application Chart on page 8 is calculated for light-
to-heavy application at a walking speed of 3 mph, or
100 ft. in ꢀ3 seconds. A variation in speed will require
an adjustment of the flow rate to maintain the same
coverage.The faster you walk, the wider the broadcast
width.
3. Pulltheflowcontrolleverbackandlatchtotheadjustable
stop for the “ON” position. Unlatch and push toward the
hopper for the “OFF” position.
USING THE PATTERN ADJUSTMENT PLATE
6. Always start the spreader in motion before opening the
closure plate.
The pattern adjustment plate is used to adjust the flow of
material being spread to the left or right side. The pattern
adjustment plate is located between the gate opening and
the spreader plate.
7. Always shut the closure plate before turning or stopping
the spreader.
8. Iffertilizerisaccidentallydepositedtooheavilyinasmall
area, soak the area thoroughly with a garden hose or
sprinkler to prevent burning of the lawn.
The adjustment of the pattern plate is sensitive and it is
recommended to test your spread pattern in a small area
first.
7
9. To insure uniform coverage, make each pass so that the
broadcast pattern slightly overlaps the pattern from the
previous pass as shown in figure 14. The approximate
broadcast widths for different materials are shown in
the Application Diagram figure 14.
IMPORTANT: Application rates shown in the chart are
affected by humidity and by the moisture content of
the material (granular and pellet). Some minor setting
adjustments may be necessary to compensate for this
condition.
10. When broadcasting weed control fertilizers, make sure
the broadcast pattern does not hit evergreen trees,
flowers or shrubs.
APPLICATION CHART
MATERIAL
TYPE
FLOW SETTING
3 MPH
(100 FT. IN ꢀ3 SEC.)
SPREAD
WIDTH IN
FEET
FERTILIZER
Powder
Granular
Pelleted
APPLICATION DIAGRAM
3-5
3-5
3-5
6-8
3-4
8-10
10-1ꢀ
6-8
Organic
GRASS SEED
Fine
Coarse
3-4
4-5
6-8
6-7
8-9
10-1ꢀ
8' to
10'
ICE MELTER
OPERATING SPEED - 3 MPH. (100 ft. in ꢀ3 seconds)
OVERLAP
FIGURE 14
8
MAINTENANCE
CHECK FOR LOOSE FASTENERS
GREASE
1. Before each use, make a thorough visual check of
the spreader for any bolts and nuts which may have
loosened. Retighten any loose bolts and nuts.
OIL
CHECK FOR wORN OR DAMAGED PARTS
ꢀ. Check for worn or damaged parts before each use.
Repair or replace parts if necessary.
CHECK TIRE INFLATION
3. Check if tires are adequately inflated before each use.
Do not inflate tires beyond maximum recommended
pressure on tire.
HAIRPIN
HAIRPIN
FIGURE 15
CAUTION: DO NOT inflate tires beyond the
maximum recommended pressure printed
on side of tire.
STORAGE
1. Rinse inside of hopper and exterior of spreader and
CLEANING
allow to dry before storing.
4. Rinse inside of hopper and exterior of spreader and
allow to dry before storing.
ꢀ. Store in a clean, dry area.
LUBRICATE (See figure 15)
SERVICE AND ADJUSTMENTS
5. Remove one small and two large hairpins and separate
the gearbox housings.
1. If the axle and gear assembly is disassembled, mark
down the positions of the parts as they are removed.
The drive wheel and large gear positions, in relation
to the small gear, determine which direction the
spreader plate will spin. Be sure to reassemble them
in their original positions. (Refer to parts exploded
view on page 10). Ensure washer (Refer to item ꢀ5
on page 10 and 11) is in place when assembling the
axle components. Add grease to gears.
6. Lightly apply automotive grease as needed to the
sprocket and gear.
7. Oil the nylon bushings on the vertical sprocket shaft.
Apply grease to the axle at least once a year, or more
often as needed.
8. Oil (idler) wheel at least once a year or more often as
needed.
ꢀ. If the agitator hairpin becomes damaged or worn, it
can be replaced. Remove old agitator hairpin from
hole in sprocket shaft and replace with new agitator
hairpin. See figure 16.
9. Install gearbox housings and secure with hairpins.
SPROCKET
SHAFT
AGITATOR
HAIRPIN
FIGURE 16
9
REPAIR PARTS FOR BROADCAST SPREADER
MODEL 45-0382 AND 45-0405
55
9
8
7
6
9
12
8
1
6
31
47
30
7
44
50
45
18
20
41
46
43
52
37
19
20
27
29
28
7
10
13
6
17
10
11
49
16
48
22
33
54
10
24
14
25
32
33
15
56
27
36
3
4
25
42
34
53
2
25
39
23
26
39
40
35
10
32
4
21
5
36
48
10
38
25
35
39
4
25
21
40
5
10
3
25
54
10
4
10
10
REPAIR PARTS FOR BROADCAST SPREADER
MODEL 45-0382 AND 45-0405
Ref.
No.
Part
No.
Qty. Description
Ref.
No.
Part
No.
Qty.
Description
ꢀ9
30
31
3ꢀ
33
34
35
36
37
38
47ꢀ05
4367
1
1
1
ꢀ
ꢀ
1
ꢀ
ꢀ
1
1
1
8
ꢀ
ꢀ
1
3
1
1
1
1
1
ꢀ
1
1
1
1
ꢀ
1
1
1
Gear, Small
Impeller
Agitator, Hairpin
1
ꢀ
44466
4884ꢀ
4884ꢀSS
ꢀ5755
ꢀ5755SS
741-0ꢀ49
49910
1543-69
49890
ꢀ567ꢀ
4989ꢀ
49891
65457
49894
44ꢀ85
49895
ꢀ5757
ꢀ3533
ꢀ5917
4388ꢀ
ꢀ5758
40199
49798
ꢀ5759
47ꢀ09
47ꢀ04
49899
43659
46055
49896
1
1
1
ꢀ
ꢀ
4
ꢀ
7
7
ꢀ
6
19
1
4
1
4
1
1
1
ꢀ
1
ꢀ
ꢀ
1
1
1
7
1
3
1
Hopper, Spreader (1ꢀ5 lb.)
Tube, Frame (45-038ꢀ)
Tube, Frame (45-0405)
Handle, Lower (45-038ꢀ)
Handle, Lower (45-0405)
Bearing, Flanged
Spacer, Axle Tube ss
Washer, Nylon
Washer, 1/4 in. Std. ss
Clip
Bolt, Hex 1/4-ꢀ0 x 1-3/4 ss
Nut, Hex 1/4-ꢀ0 Nylock ss
Weldment, Guide Closure
Bolt, Slot Truss 10-3ꢀ x 1/ꢀ in. ss
Bushing, Hopper
Hex Nut, 10-3ꢀ Nylock ss
Pattern, Plate
Closure, Plate
48934
47ꢀ1ꢀ
49897
49898
49930
49907
4990ꢀ
ꢀ576ꢀ
ꢀ576ꢀSS
49909
ꢀ5761
ꢀ5761SS
ꢀ4855
49908
ꢀ5760
43848
ꢀ5763
49903
47141
49904
49931
49901
14ꢀ
Housing, Large Gear
Hairpin, Clip Large
Hairpin, Clip Small
Spacer, Tube
Wheel, Poly 5/8 in. ID x 13-5.00
Flow Control Rod
Tube Stand (45-038ꢀ)
Tube Stand (45-0405)
Bolt, Hex 1/4-ꢀ0 x 1-1/ꢀ in.
Handle, Upper (45-038ꢀ)
Handle, Upper (45-0405)
Flow Control Bracket
Bolt, Hex 1/4-ꢀ0 x ꢀ-1/ꢀ in. ss
Lever, Flow Control
Grip, Control Arm
Stop, Adjustable ss
Bolt, Carr. 1/4-ꢀ0 x 3/4 in.
Nut, Wing 1/4-ꢀ0 Nylon
Grip, Handle
3
4
5
6
7
8
9
39
40
10
11
1ꢀ
13
14
15
16
17
18
19
ꢀ0
ꢀ1
ꢀꢀ
ꢀ3
ꢀ4
ꢀ5
ꢀ6
ꢀ7
ꢀ8
41
4ꢀ
43
44
45
46
47
48
49
50
5ꢀ
53
54
55
56
Slide Gate Angle Bracket ss
Rivet, POP ss 3/16 in.
Link, Flow Control ss
Bolt, Hex 1/4-ꢀ0 x 3/4 in. ss
Fitting. Grease 1/4 in.
Shaft, Axle Spreader ss
Gear, Large
Screw, Thumb 1/4-ꢀ0 x 1-1/4 in.
Spring, ss
Pin, Cotter 1/8 x 3/4 in.
Pin, Cotter 5/3ꢀ x ꢀ in.
Pin, Cotter 9/64 x 1-1/ꢀ in.
Screen, Spreader
40ꢀ49
49911
47441
405ꢀ0
49905
Yoke, Large
Washer, Flat 5/8 in. ID x 1 in. OD
Spring, Pin, 3/16 x 1 in.
Spring, Pin 1/8 x 1 in.
Shaft, Impeller ss
Nut, Nylon
Owners Manual (Not Shown)
11
REPAIR PARTS
Agri-Fab, Inc.
809 South Hamilton
Sullivan, IL 61951
ꢀ17-7ꢀ8-8388
© ꢀ006 Agri-Fab, Inc.
|