™
TIPS
TION
APPLICA
owners
manual
model no.
45-02153-131
100 lB.Tow
BroaDCasT sPreaDer
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
Assembly
Operation
Maintenance
Repair Parts
PRINTED IN U.S.A.
FORM NO. 40537 (REV. 10/25/07)
5. Assemble the two hitch braces to the hitch tube using a
1/4" x 1-1/2" hex bolt and a 1/4" nylock nut. See figure
3. Do not tighten at this time.
8. Place the drive wheel onto the end of the axle that has
an indent. The long end of the hub goes to the inside.
See figure 5.
6. Tighten all loose hex nuts and bolts attached to hitch
tube and hitch braces. Do not collapse tubes when
tightening.
9. Place a hub cap onto the end of the axle. Using a small
hammer, lightly tap the hub cap until it is snug against
the wheel. See figure 5.
HITCH
TUBE
INDENT
1/4" x 1-1/2"
HEX BOLT
1/4" NYLOCK
NUT
HUB CAP
HITCH BRACE
HITCH BRACE
FIGure 5
FIGure 3
7. Assemble a spacer and then a 1/2" flat washer onto
10. Place the wheel (long end of hub first) onto the end of
the axle that has no indents. See figure 6.
each end of the axle. See figure 4.
11. Place a 1/2" flat washer onto the axle and then lightly
tap a hub cap onto the axle until it is snug against the
washer and wheel hub. See figure 6.
AXLE
END WITH NO
INDENT
SPACER
1/2" DIA.
FLAT WASHER
1/2" FLAT
WASHER
FIGure 4
HUB CAP
FIGure 6
3
12. Position the flow control mounting bracket (figure 7).
a. Push on flow control arm until it locks in "OFF"
position.
oPeraTIon
How To useYour sPreaDer
b. Slide flow control mounting bracket along tube until
closure plate in bottom of hopper just closes.
c. Snug the 1/4" lock nuts just enough to hold flow
control mounting bracket in place.
seTTInG THe Flow ConTrol
(Refer to figure 7 on page 4.)
d. Set adjustable stop at "5". Pull flow control arm
against stop. Verify that closure plate has opened
about half way.
e. If closure plate does not open half way, it may be
closedtoofarat"OFF".Adjustpositionofflowcontrol
mounting bracket until closure plate will open about
half way at "5" and still close when arm is locked in
"OFF". Tighten 1/4" lock nuts.
1. Loosen the nylon wing nut, set the adjustable stop to
the desired flow rate setting and retighten the wing nut.
The higher the setting number, the wider the opening
in the bottom of the hopper.
2. Refer to the application chart on page 5 and to the
instructions on the fertilizer bag to select the proper
flow rate setting.
3. Pull the flow control arm against the adjustable stop
for the on position and toward the hopper for the off
position.
OFF
ON
usInGYour sPreaDer
We do not recommend the use of any powdered lawn
chemicals, due to difficulty in obtaining a satisfactory or
consistent broadcast pattern.
FLOW
CONTROL
ARM
OFF
ON
1. Determine approximate square footage of area to be
covered and estimate amount of material required.
2. Before filling the hopper make sure the flow control arm
is in the off position and the closure plate is shut.
3. Break up any lumpy fertilizer as you fill the hopper.
4. Set the adjustable stop with the flow control arm still in
the off position. Refer to the application chart on this
pageandtotheinstructionsonthefertilizerbagtoselect
the proper flow rate setting.
1
2
3
4
5
6
7
8
9
1
0
5. The application chart is calculated for light to heavy
application at a vehicle speed of 3 mph, or 100 ft. in 23
seconds.A variation in speed will require an adjustment
oftheflowratetomaintainthesamecoverage.Thefaster
you drive, the wider the broadcast width.
AJDUSTABLE
STOP
SETTING "5"
6. Alwaysstartthetractorinmotionbeforeopeningclosure
plate.
FIGure 7
7. Always shut the closure plate before turning or stopping
the tractor.
8. Iffertilizerisaccidentallydepositedtooheavilyinasmall
area, soak the area thoroughly with a garden hose or
sprinkler to prevent burning of the lawn.
9. To insure uniform coverage, make each pass so that the
broadcast pattern slightly overlaps the pattern from the
previous pass as shown in figure 8. The approximate
broadcast widths for different materials are shown in
the application chart on this page.
10. When broadcasting weed control fertilizers, make sure
the broadcast pattern does not hit evergreen trees,
flowers or shrubs.
11. Heavy moisture conditions may require a cover over
the hopper to keep contents dry. The vinyl cover acts
as a wind and moisture shield, but should not be used
as a rain cover.
4
CleanInG
4. Rinse inside of hopper and exterior of spreader and dry
off before storing.
luBrICaTe (See figure 9.)
5. Lightlyapplyautomotivegreaseasneededtothesprocket
REFER
TO
CHARTS
and gear.
6. Oilthenylonbushingsontheverticalsprocketshaftandon
the axle at least once a year, or more often as needed.
7. Oil right hand (idler) wheel bearing at least once a year or
more often as needed.
OVERLAP
OIL
FIGure 8
ImPorTanT: Applicationratesshowninthechartareaffected
by humidity and by the moisture content of the material
(granular and pellet). Some minor setting adjustments may
be necessary to compensate for this condition.
OIL
GREASE
FIGure 9
aPPlICaTIon CHarT (sHIelD uP)
TYPe
maTerIal
sPreaD
wIDTH
sToraGe
Flow seTTInG
FerTIlIZer
Powder
Granular
Pelleted
Organic
Grass seeD
Fine
1. Rinse inside of hopper and exterior of spreader and dry
off before storing.
2. Store in a clean, dry area.
3 - 5
3 - 5
3 - 5
6 - 8
3' - 4'
8' - 10'
10' - 12'
6' - 8'
serVICe anD aDJusTmenTs
3 - 4
4 - 5
6 - 8
6' - 7'
8' - 9'
10' - 12'
1. If the axle, slotted gear and sprocket assembly is
disassembled, mark down the positions of the parts as
theyareremoved.Thedrivewheelandsprocketpositions
in relation to the slotted gear determine which direction
thespreaderplatewillspin.Besuretoreassemblethem
in their original positions. (Refer to figure 5 on page 3.)
Use shim washers (Ref. no. 21 on pages 6 and 7) as
needed for minimum backlash. Add grease to gear and
sprocket.
Coarse
ICe melTer
oPeraTInG sPeeD - 3 MPH. (100 ft. in 23 seconds)
maInTenanCe
CHeCK For loose FasTeners
1. Before each use make a thorough visual check of the
spreader for any bolts and nuts which may have loosened.
Retighten any loose bolts and nuts.
2. If the agitator hairpin becomes damaged or worn it can
be replaced. See figure 10.
SPROCKET
SHAFT
CHeCK For worn oF DamaGeD ParTs
2. Checkforwornordamagedpartsbeforeeachuse.Repair
or replace parts if necessary.
CHeCKTIre InFlaTIon
3. Check if tires are adequately inflated before each use.Do
not inflate beyond maximum recommended pressure.
AGITATOR
HAIRPIN
CauTIon: Do noT inflate tires beyond the
maximum recommended pressure printed
on side of tire.
FIGure 10
5
rePaIr ParTs For BroaDCasT sPreaDer moDel 45-02153-131
49
15
4
1
A
12
40
31
7
9
13
40
9
9
5
39
50
11
33
3
35
34
6
2
B
26
46
40
9
A
12
11
28
25
22
48
27
11
10
24
9
23
4
44
7
37
32
B
8
42
39
39
D
E
9
45
40
9
32
36
33
19
19
9
9
7
7
23
39
9
32
24
22
21
32
32
20
21
18
43
11
E
17
41
38
35
9
14
D
47
22
11
51
16
22
50
6
rePaIr ParTs For BroaDCasT sPreaDer moDel 45-02153-131
reF ParT no. QTY DesCrIPTIon
reF ParT no. QTY DesCrIPTIon
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
44624
46055
62482
40469
23753
23758
43661
24857
47189
44591
43648
1509-69
44566
44586
40539
40540
23687
23781
44665
44672
44137
1
1
1
1
1
1
5
1
Hopper
27
28
29
31
43850
44468
C-9M5732
48934
1
1
2
1
9
2
1
2
1
1
1
Pin, Spring 1/8" Dia. x 5/8" Lg.
Sprocket, 6 Tooth
Pop Rivet (not shown)
Hairpin Agitator
Washer, 5/16 SAE
Bushing, Delrin
Rod, Flow Control
Brace, Hitch
Support, Shaft
Nylon Wing Nut, 1/4-20 Thd.
Bolt, Carriage 1/4-20 x 3/4" Lg.
Pin, Spring 1/8" Dia. x 1" Lg.
Ass'y, Guide Closure
Tube, Frame
Slide Gate Angle Bracket
Slide Gate Bracket
Bolt, Hex 1/4-20 x 1" Lg.*
Flow Control Link
32 R19111116
33
34
35
36
37
38
39
40
41
42
43
44
45
44285
44469
23525
23780
47141
44950
1543-69
43088
24858
24855
46885
24859
44101
23533
47623
43848
40883
44663
43343
40537
22 Nylock Nut, 1/4-20
1
9
7
1
1
1
1
1
1
2
1
6
4
2
2
1
1
Tube, Crossover
Bolt, Hex 1/4-20 x 1-1/2" Lg.
Bolt, Hex 1/4-20 x 1-3/4"
Spring, Torsion
Tube, Hitch
Drive Wheel
Wheel
Bracket, Hitch
Shaft, Axle
10 Washer, Nylon
16 Washer, Flat 1/4" Std.
1
1
1
1
1
1
1
1
1
2
1
1
Adjustable Stop
Bracket, Flow Control Mount
Gear
Flow Control Arm
Cotter Pin 3/32" x 3/4" Lg.*
Plate, Closure
Pin, Spring 5/32" Dia. x 1-1/4" Lg. 46
Bushing, Axle Shaft
Washer, Shim 1/2"
Washer, Flat 1/2"
Bearing, Flange
Tube, Spacer
47
48
49
50
51
Hitch Pin
Grip, Flow Control Arm
Vinyl Hopper Cover
Hub Cap
Hair Cotter Pin, #4 1/8"
Owner's Manual
22 R19171616
23
24
25
26
47963
46501
25305
04367
Shaft, Sprocket
Spreader Plate
7
rePaIr ParTs
Agri-Fab, Inc.
809 South Hamilton
Sullivan, IL. 61951
217-728-8388
© 2007 Agri-Fab, Inc
|