T E C H N O L O G I E S
User Guide
NAS 2.0 Adapter
(NAS2XU2)
v5.1.11
Technical Support
If you need any assistance to get your unit functioning properly, please have your
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
I.
NAS2XU2 Hardware Installation
Access LED
System LED
Power LED
USB Mass
5V Power Jack
Reset Button
RJ45 Socket
Storage Device
USB Printer
1.
Connect external USB Storage device into USB port of the NAS
Adapter. Power on the USB Storage device.
2.
3.
Connect LAN cable via LAN switch and Router.
Connect 5V power adapter to power up the NAS adapter
NAS2XU2 connected directly to a computer’s NIC card
If you connect the NAS2XU2 to a computer directly, the will act as a DHCP server,
assigning itself an IP address automatically and will also assign an IP address to the
computer’s network card. This configuration will not enable you to see the drive on
the network.
NAS2XU2 connected to a Router or Switch
When the NAS2XU2 is connected to a LAN network with an active DHCP server, it
will obtain an IP address from DHCP server automatically. Or if your LAN network
does not have an active DHCP server, NAS2XU2 will immediately act as DHCP
server and assign itself an IP address for installation.
II.
Search NAS2XU2 using SDisk Utility
1.
Browse the CD enclosed in the product package. Copy and paste
“SDisk Utility” in to your computer then double click the icon to start
search.
Note: “SDisk utility” was written with JAVAscript, please make sure your computer
has installed JAVA before, if not please install the JAVA JRE from the CD drive.
Technical Support (M-F 8:30am - 6:00pm PST)
Phone: 408-453-6212
2.
When NAS2XU2 has been found, click “Connect” to enter web GUI
utility.
Open NAS2XU2 web GUI by using web browser.
1.
2.
Open web browser and type default host name “storage” in the
search bar.
Default login is “admin” for both User name and password. Click
“OK” to enter configurations.
Identification
You can change and modify your host, group name and password from this page.
Click “Apply” to save the setting.
Host name: This is used to identify your device on the network. If you prefer
a different name, type in the new name and click “Apply” to save setting.
Group Name: This should be the same as your workgroup. In general, the
default “WORKGROUP” will be OK. But if your workstation belongs to
different workgroup, type in the correct group name to modify.
For Window OS, right click on “My computer” and choose “Properties”, go to the
computer name tab to see your current workgroup.
If using a Mac OS system, to join a Windows workgroup, open the directory access
utility (under Applications-> utilities). Select SMB and click configure to modify the
settings (administrator access required to access this option.)
Note: We strongly suggest you to change the password as soon as you
logged in, to prevent unauthorized access.
Technical Support (M-F 8:30am - 6:00pm PST)
Phone: 408-453-6212
LAN Configuration
By default, “LAN Config” is set to “Automatic IP”. This will allow the NAS2XU2 to
obtain its IP address automatically. If you prefer setting it manually, select the static
IP option, enter your own value and click “Apply” to confirm the new setting.
Disk Utility
In this page, you can manage hard disk settings of the USB storage device.
Format: For first time installation, you need to format hard disk into FAT32
file system. Formatting the drive will erase all data on the hard drive.
Warning: For hard drives with data on it, create a backup before
proceeding to format the hard drive!
Tip: You can transfer back the backup data to the NAS Public folder for
sharing via the network or USB connection of the USB Storage device.
Scan Disk: After the scan, it will show file content information and health
status for the hard disk.
To access Samba PUBLIC folder of NAS2XU2 in Windows
Click on the Windows icon located on the bottom left corner of the screen, on the
“Search programs and files” \\ followed by the IP address.
Eg:\\192.168.1.121 and press Enter key to continue.
Technical Support (M-F 8:30am - 6:00pm PST)
Phone: 408-453-6212
Type “Guest” as username. Leave password empty. Click on OK.
This will direct you to the Public folder on the NAS drive.
Now you have set up the folder that you wish to share on your NAS . This folder can
be access from other computer on your local network.
Technical Support (M-F 8:30am - 6:00pm PST)
Phone: 408-453-6212
To list the NAS drive in Network Places
Go to Network Places in Windows XP, under Network Tasks, click on the “Set
up a home or small office network”. Follow the wizard and once completed,
reboot your system.
For Vista and Windows 7, enable file sharing when accessing the NAS over
the network.
To access Samba PUBLIC folder of NAS2XU2 in Ubuntu 8.04
First, using the console get the prerequisites for the samba file system:
$ sudo aptitude install samba smbfs
$ mkdir /mnt/NAS
$ sudo mount.cifs //NAS__IP_address/Public /mnt/NAS -o username=Guest
To access Samba PUBLIC folder of NAS2XU2 in Mac OS X
1.
2.
3.
4.
Start at the "Go" drop down menu at the top of your screen,
then click "Connect to server".
Type into the "Server Address" field 'smb://' followed by the
IP address of the NAS2XU2 you want to connect.
Click the "Connect" button in the bottom right corner of the
window.
Enter in a username and password. Click the "OK" button in
the bottom right hand corner of the window to finish.
Note: The workgroup name needs to be the workgroup the
PC belongs to. If you don't know the workgroup that the PC
belongs to you can find out by right clicking on the "My
Computer" desktop icon on the PC, selecting "Properties"
and then selecting the "Computer Name" tab. The work
group name is about half way down the window.
5.
Select the "share" you are after. This simply refers to a
particular group of shared files. Click "OK".
Technical Support (M-F 8:30am - 6:00pm PST)
Phone: 408-453-6212
CONTACT US
Phone:
Fax:
408-573-8580
408-573-8588
Email:
Technical Support (M-F 8:30am - 6:00pm PST)
Phone: 408-453-6212
|