User’s Guide
MiniSCSI 1350
Parallel Port to SCSI Adapter
APA-1350
R
▼ ▼ ▼ ▼
MiniSCSI 1350
Parallel Port to SCSI Adapter
User’s Guide
R
Introduction
Thank you for purchasing the Adaptec MiniSCSI 1350. The
MiniSCSI 1350 is the ideal solution for Plug & Play SCSI connections
to CD-ROMs, Scanners, Hard Disks, SyQuest, Iomega, Tape, MO
drives and other peripherals. It’s fast, easy installation adds full
SCSI flexibility to your Portable or Desktop PC without the hassle
and cost of plug-in host adapters. Simply plug it into your PC’s
parallel port and you’re set.
Contents of Kit
■ MiniSCSI 1350 Parallel Port to SCSI Adapter
■ User’s Guide
■ Registration Card
■ Windows 95 Setup Diskette
System Requirements
■ Supports 486 and Pentium based portable or desktop systems.
■ Operates on Standard, Unidirectional, Bidirectional, PS/ 2, EPP
and ECP (IEEE 1284) parallel ports.
1
MiniSCSI 1350 User’s Guide
Installing the MiniSCSI 1350
Follow the steps below to install the MiniSCSI 1350 and connect
of a typical installation.
1
2
3
Connect the 50-pin interface plug to the SCSI interface socket
on your peripheral device.
Plug the 25-pin interface plug into a parallel-printer connector
on your computer.
Optional: If a printer cable is already attached to the connector,
unplug it and connect it to the 25-pin socket on the MiniSCSI
1350.
Note: This is a pass-through printer connection that
will allow printing while your SCSI peripheral is in
use.
4
Ensure that your SCSI peripheral is properly terminated and
then switch on power to your SCSI peripheral. The green
power indicator on the MiniSCSI 1350 will now be illuminated
and you are ready to install the software.
2
Installing the MiniSCSI 1350
Note: For the pass-through function to operate, your
SCSI peripheral must be connected and powered up
because the MiniSCSI 1350 uses the power on the SCSI
bus.
25-Pin Interface Plug
Printer
Laptop
25-Pin Socket
SCSI Device
50-pin Interface Plug
Figure 1. Typical Installation
3
MiniSCSI 1350 User’s Guide
Software Installation
To use your MiniSCSI 1350, you have to install software drivers on
your computer. This one time process is described below.
Note: Before you begin, we recommend that you make
copies of the diskettes that came with your MiniSCSI 1350.
Before you begin, close any application you may have running
before installing the MiniSCSI 1350 software drivers.
Windows 95 Software Installation
1
Start Windows 95.
2
Insert the diskette labeled APA-1350 Setup Diskette into floppy
drive A.
3
4
5
Double-click on the My Computer icon.
Double-click on the Floppy Drive A.
Double click on the SETUP icon. The installation process will
begin. Follow the on-screen instructions until the installation
is complete. At the end of the installation process, a text file
called README.TXT will be displayed. This file contains
additional installation instructions, a troubleshooting section,
and un-install instructions.
Note: README.TXT can also be viewed at any later
time using Notepad. It will be copied to the folder on
the hard disk where the APA-1350 drivers have been
installed. The default directory is C:\ MINISCSI.
After installation the devices can be accessed through Microsoft
Windows 95’s My Computer or Explorer applications. Audio CDs
can be played using CD-Player in the Multimedia group of the
Accessories section of the Program menu.
4
Software Installation
Printers
In most cases and with most printers, printing via the printer pass-
through connector should not be any different than printing via the
computer’s own printer port. The printer pass-through connector
on the MiniSCSI 1350 can be used to connect a printer or any
peripheral device that normally connects to a parallel-printer
connector.
Note: The printer pass-through connector will only work
when the SCSI peripheral is attached and powered ON.
5
MiniSCSI 1350 User’s Guide
Uninstalling the Drivers
To uninstall the MiniSCSI 1350 drivers from your system
1
2
Go to the Control Panel and double-click on Add/Remove
Programs icon.
Highlight the MiniSCSI 1350 driver entry and click
Add/Remove. The drivers will be removed from your system.
3
4
Re-boot the system to reflect the change.
Follow the instructions below to prevent the MiniSCSI 1350
from loading on bootup automatically. First, determine which
version of Windows 95 you have installed. To do this check in
the System Properties dialog box in the Control Panel.
Windows 95 OSR2 will be displayed as Windows 95 4.00.950 B.
Windows 95 Standard will be displayed as Windows 95 4.00.950.
Windows 95 Standard
a
Go to the Control Panel and double-click on the System
icon.
b
c
Click the Device Manager tab.
Double-click the MiniSCSI 1350 device entry under SCSI
controllers.
d
Uncheck the box next to Original Configuration in the Device
Usage field. The MiniSCSI 1350 will not load. This can be
verified by the red "X" that will be displayed alongside the
MiniSCSI 1350 entry in the Device Manager.
Windows 95 OSR2
a
Go to the Control Panel and double-click on the System
icon.
b
c
Click the Device Manager tab.
Double-click the MiniSCSI 1350 device entry under SCSI
controllers.
d
Check the first box — Disable in this hardware profile. The
MiniSCSI 1350 will not load. This can be verified by the red
"X" that will be displayed alongside the MiniSCSI 1350 entry
in the Device Manager.
6
Understanding SCSI
Understanding SCSI
SCSI (pronounced “scuzzy”) stands for Small Computer Systems
Interface. SCSI is an industry standard computer interface for
connecting SCSI devices (such as hard disk drives, CD-ROM drives,
and scanners) to a common SCSI bus.
A SCSI bus is an electrical pathway consisting of a SCSI adapter
(such as the SlimSCSI adapter) installed in a computer and one or
more SCSI devices. SCSI cables are used to connect the devices to the
SCSI card. For the SCSI bus to function properly, SCSI IDs must be
assigned to the SCSI devices and the SCSI adapter, and the SCSI bus
must be properly terminated.
SCSI IDs
Each device attached to the MiniSCSI 1350 adapter, as well as the
adapter itself, must be assigned a unique SCSI ID number from 0 to
6. A SCSI ID uniquely identifies each SCSI device on the SCSI bus
and determines priority when two or more devices are trying to use
the SCSI bus at the same time.
■ The MiniSCSI 1350 adapter is preset to SCSI ID 7, which gives
it the highest priority on the SCSI bus.
■ In Windows 95, you can use the Device Manager to view the
SCSI ID and other information about each installed SCSI
device.
7
MiniSCSI 1350 User’s Guide
Terminating the SCSI Bus
To ensure reliable communication on the SCSI bus, terminators must
be installed (or enabled) on the devices at the physical ends of the
SCSI bus. The terminators on all devices between the physical ends
must be removed (or disabled). Termination on the MiniSCSI 1350 is
permanently enabled, since it is always at one end of the SCSI bus.
There are various methods for terminating disk drives and other
SCSI devices. Read the device documentation if you are not sure
how to do this. Here are some general guidelines for termination:
■ Termination is usually controlled by installing or removing a
SCSI terminator. On some SCSI devices, termination is
controlled by setting a switch on the back of the device.
■ Most SCSI devices come from the factory with termination
enabled.
Obtaining SCSI Cables
You will need additional SCSI cables if you connect more than one
SCSI device to your MiniSCSI 1350. It is important to use high-
quality cables to ensure that data is read and written correctly.
Adaptec provides high-quality SCSI cables designed specifically for
use with the MiniSCSI 1350. (To order Adaptec SCSI cables, call
1-800-442-7274, Monday to Friday, from 6 a.m. to 5 p.m. Pacific
Time).
8
Understanding SCSI
Connector Types
Several different types of SCSI connectors are used on SCSI devices,
and each type requires a different kind of cable. The following
diagrams illustrate the different kinds of SCSI connectors:
SCSI-2 High-density 50-pin Connector
Standard MiniSCSI 1350 Connector for SCSI Perirpherals
Typically used with high-performance CD-ROM drives, hard disk drives, Jaz drives, and Plug
and Play devices.
If you have a SCSI device with a DB25 pin or low density 50-pin
(SCSI-2) connection, you can order converters from Adaptec's web
site.
DB25 Connector
Used with Iomega ZIP drives, Syquest EZFlyer, etc.
SCSI-1, Low-density Centronics 50-pin Connector
Used with many CD-ROM drives, hard disk drives, SCSI tape drives, and scanners
9
MiniSCSI 1350 User’s Guide
Troubleshooting
Most problems with the MiniSCSI 1350 result from errors in
preparing and connecting the SCSI devices to it. So, if you have
problems, check the General Hardware Troubleshooting tips first. If the
problem still remains, refer to one or more of these sections:
Formatting your Hard Disk Drives
in DOS or Windows 95..................................page 13
General Hardware Troubleshooting
■ Be sure all connectors are firmly connected
■ Be sure all SCSI cables and power cables are properly
connected and all SCSI devices are powered
■ Be sure last SCSI device (or only) is terminated
■ Be sure at least one SCSI device connected to the
MiniSCSI 1350 supplies termination power to the SCSI bus.
Otherwise, the SCSI devices will not work correctly.
Note: Some devices have a switch to enable or disable
termination power. See the device documentation for
more information.
10
Troubleshooting
WINDOWS 95 Troubleshooting
■ I can read from my CD-R or CD-RW but Easy CD Pro doesn’t
recognize the drive, therefore I’m unable to write to the CD?
Please check the revision of Easy CD Pro. Adaptec has fixed
problems in their latest revision (2.11C). This is found on their
website:
http:/ / www.adaptec.com/ support/ files/ upgrades.html
The file you need is Easy2up.exe, and is found under the
section CD recordable software upgrades PC.
■ In the Device Manager under SCSI controllers the MiniSCSI
1350 controller is recognized but the CD drive isn’t listed
under CD-ROM.
Please check that you are using the very latest installer from
Adaptec. Also, check the SCSI ID of the CD ROM, make sure it
is not ID 7, 1 or 0.
■ Can I use FDISK to prepare my hard disk?
In order to partition a hard disk drive with the FDISK
command, Int 13h support has to be enabled. For instructions
■ My EPST connection is running in Nibble mode, what
should I do?
At present EPST doesn’t support the parallel mode ECP
properly. If you change the port mode to EPP you will find a
performance increase.
11
MiniSCSI 1350 User’s Guide
Improving Overall Performance
Following are some tips on improving the performance of the
MiniSCSI 1350:
■ Ensure that the CMOS setting configuration for the parallel
port and the setting in the Device Manager are the same.
■ Ensure that there are no Port Base and IRQ clashes with other
installed devices such as Sound Cards.
■ If the parallel port supports EPP, ensure that the parallel port
mode in the system CMOS is set for EPP.
■ To step up the system performance, in the Control Panel, select
System, select the Performance tab, click on File System, ensure
that the Performance is set to Full.
■ Select the Trouble Shooting tab and ensure that the Write
Behind Cache is enabled. These are usually the default
settings.
■ The MiniSCSI 1350s are programmed to give maximum
performance for the following parallel port Port Base and IRQ
combinations: 378h and 3BCh and IRQ 7 Port Base and IRQ
combinations other than these are likely to slow down the
performance.
■ Ensure that the total cable length does not exceed 3 meters and
that no more than 7 devices are attached. For optimum
performance we recommend attaching only 4 devices.
12
Troubleshooting
Formatting your hard disk drives in Windows 95
If a hard disk drive is used that has not been formatted for Windows
95 systems, you will need to prepare the Disk for its first use with
the FDISK and FORMAT commands in the DOS directory of your
system disk. Before you can use these commands you must enable
Int 13 support for the drive.
Follow these steps to enable Int 13 support:
1
2
3
4
5
Go to the Control Panel.
Double-click on the System icon.
Click on the Device Manager tab.
Double-click on Disk drives.
Double-click on the icon for the Disk attached to your
MiniSCSI 1350.
6
7
8
Click on the Settings tab.
Click on the Int 13 Unit field in the Options section.
Reboot for the change to take effect.
Once you have completed initialization of the disk, you can repeat
the above procedure to disable the Int 13 support of your Disk. This
may improve performance.
❒
13
Contacting Adaptec
Contacting Adaptec
If you have questions about installing or using your Adaptec
product, check this User’s Guide first—you will find answers to most
of your questions here. If you need further assistance, please contact
us. We offer the following support and information services:
Electronic Support
Technical information, including product literature, answers to
commonly asked questions, information on software upgrades and
other topics is available electronically through the following:
■ Adaptec World Wide Web (WWW) site at
■ File Transfer Protocol (FTP) server at ftp.adaptec.com
■ Adaptec USA Bulletin Board Service (BBS); supports up to
28,800 bps (bits per second), 8 data bits, 1 stop bit, no parity.
No product literature is available on the Adaptec BBS.
USA: (408) 945-7727
Belgium: (32) 2-352-3454
Germany: (49) 89-45640618
France: (33) 1-3060-9539
UK: (44) 1276-684184
■ Interactive Fax System available 24 hours a day, 7 days a week.
USA: 408-957-7150
Europe: (32) 2-352-3869
15
MiniSCSI 1350 User’s Guide
Technical and Product Support
■ For technical support and information about many of
Adaptec’s electronic support services, call 800-959-7274 or
408-945-2550, 24 hours a day, 7 days a week.
■ To use the Adaptec Interactive Support System, call
800-959-7274 or 408-945-2550, 24 hours a day, 7 days a week.
The system prompts you with questions regarding your
problem and then provides step-by-step troubleshooting
instructions.
■ To speak with a product support representative, call
408-934-7274, M–F, 6:00 A.M. to 5:00 P.M., Pacific Time. After
hours, on weekends, and on holidays, product support is also
available for a fee at 800-416-8066.
■ To speak with a product support representative in Europe call:
French: (32) 2-352-3460
English: (32) 2-352-3470
German: (32) 2-352-3480
Sales and Ordering Information
■ For sales information, call 800-959-7274 or 408-945-2550, M–F,
6:00 A.M. to 5:00 P.M., Pacific Time.
■ To order Adaptec software and SCSI cables, call 800-442-7274
or 408-957-7274, M–F, 6:00 A.M. to 5:00 P.M., Pacific Time.
■ To request additional documentation for Adaptec products,
call 800-934-2766 or 510-732-3829, M–F, 6:00 A.M. to 5:00 P.M.,
Pacific Time.
■ For sales information in Europe call:
France: (33) 1-34-523434
Germany: (49) 89-4564060
UK: (44) 1276-854500
16
Contacting Adaptec
Copyright
© 1998 Adaptec, Inc. All rights reserved. No part of this publication
may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical, photocopying,
recording or otherwise, without the prior written consent of
Adaptec, Inc., 691 South Milpitas Blvd., Milpitas, CA 95035.
Trademarks
Adaptec, the Adaptec logo, AIC, APA, SlimSCSI, EZ-SCSI, and
SCSIExplorer are trademarks of Adaptec, Inc. which may be
registered in some jurisdictions. Windows, Windows NT, and
Windows 95 are registered trademarks of Microsoft Corporation in
the U.S. and other countries used under license. All other
trademarks are owned by their respective owners.
Changes
The material in this document is for information only and is subject
to change without notice. While reasonable efforts have been made
in the preparation of this document to assure its accuracy, Adaptec,
Inc. assumes no liability resulting from errors or omissions in this
document, or from the use of the information contained herein.
Adaptec reserves the right to make changes in the product design
without reservation and without notification to its users.
Disclaimer
IF THIS PRODUCT DIRECTS YOU TO COPY MATERIALS, YOU
MUST HAVE PERMISSION FROM THE COPYRIGHT OWNER OF
THE MATERIALS TO AVOID VIOLATING THE LAW WHICH
COULD RESULT IN DAMAGES OR OTHER REMEDIES.
17
MiniSCSI 1350 User’s Guide
Federal Communications Commission Radio Frequency Interference Statement
WARNING: Changes or modifications to this unit not expressly approved by the party responsi-
ble for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no guaran-
tee that interference will not occur in a particular installation. However, if this equipment does
cause interference to radio or television equipment reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/ television technician for help.
Use a shielded and properly grounded I/ O cable and power cable to ensure compliance of this
unit to the specified limits of the rules.
This device complies with part 15 of the FCC rules. Operation is subject to the following two con-
ditions: (1) this device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Adaptec, Inc.
MiniSCSI 1350
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
Canadian Compliance Statement
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matérial
brouilleur du Canada.
18
Contacting Adaptec
Adaptec Software License Agreement
In return for acquiring a license to use the software (“Software”) and related documentation, you
agree to the following terms and conditions:
1
License: This Agreement grants you, the Licensee, a license to:
a
b
use the Software on a single computer system which incorporates an Adaptec SCSI
Card, or in the case of a multi-user or networked system which permits access to
the Software by more than one user at the same time, at a single working location.
make one copy of the Software in machine readable form solely for back-up pur-
poses provided you reproduce Adaptec’s copyright notice and any proprietary
legends.
2
3
Restrictions: You may not distribute copies of the Software to others or electronically
transfer the Software from one computer to another over a network. You may not use
the Software from multiple locations of a multi-user or networked system at any one
time. The Software contains trade secrets and in order to protect them you may not
decompile, reverse engineer, disassemble, or otherwise reduce the Software to a
human-perceivable form. YOU MAY NOT MODIFY, ADAPT, TRANSLATE, RENT,
LEASE, LOAN, RESELL FOR PROFIT, DISTRIBUTE, NETWORK OR CREATE
DERIVATIVE WORKS BASED UPON THE SOFTWARE OR ANY PART THEREOF.
Ownership of Software: As Licensee, you own the media upon which the software is
fixed, but Adaptec retains title and ownership of the Software recorded on the original
media and all subsequent copies of the Software regardless of the form or media in
which or on which the original and other copies may exist. This license is not a sale of
the Software or any copy.
4
5
Confidentiality: You agree to maintain the Software in confidence and to not disclose
the Software to any third party without the express written consent of Adaptec. You
further agree to take all reasonable precautions to preclude access of unauthorized
persons to the Software.
Term: This license is effective until January 1, 2042, unless terminated earlier. You may
terminate the license at any time by destroying the Software (including the related
documentation) together with all copies or modifications in any form. Adaptec will
have the right to terminate your license immediately if you fail to comply with any
term or condition of this Agreement. Upon any termination, including termination by
you, you must destroy the Software (including the related documentation) together
with all copies or modifications in any form.
6
Limited Warranty: Adaptec warrants only that the media upon which the Software is
furnished will be free from defects in material or workmanship under normal use and
service for a period of thirty (30) days from the date of delivery to you. ADAPTEC
DOES NOT AND CANNOT WARRANT THE PERFORMANCE OR RESULTS YOU
MAY OBTAIN BY USING THE SOFTWARE OR DOCUMENTATION. THE FOREGO-
ING STATES THE SOLE AND EXCLUSIVE REMEDIES ADAPTEC WILL PROVIDE
FOR BREACH OF WARRANTY. EXCEPT FOR THE FOREGOING LIMITED WAR-
RANTY, ADAPTEC MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AS TO
NONINFRINGEMENT OF THIRD PARTY RIGHTS, MERCHENTABILITY OR FIT-
NESS FOR A PARTICULAR PURPOSE. Some states do not allow the exclusion of
implied warranties or limitations on how long an implied warranty may last, so the
above limitations may not apply to you. This warranty gives you specific legal rights
and you may also have other rights which vary from state to state.
7
8
Limitation of Liability: IN NO EVENT WILL ADAPTEC BE LIABLE TO YOU FOR
ANY SPECIAL DAMAGES, INCLUDING ANY LOST PROFITS, LOST SAVINGS OR
OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF ADAPTEC
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY
CLAIM BY ANY OTHER PARTY. Some states do not allow the exclusion or limitation
of special, incidental, or consequential damages, so the above limitation or exclusion
may not apply to you.
Limitation of Remedies: Adaptec’s entire liability and your exclusive remedy shall be:
19
MiniSCSI 1350 User’s Guide
a
b
the replacement of any media not meeting Adaptec’s limited warranty which is
returned to Adaptec; or
if Adaptec or its distributor is unable to deliver replacement media which is free of
defects in materials or workmanship, you may terminate this Agreement by
returning the Software and your money will be refunded.
9
Export: You acknowledge that the laws and regulations of the United States restrict
the export and re-export of the Software. You agree that you will not export or re-
export the Software or media in any form without the appropriate United States and
foreign government approval.
10 U.S. Government Restricted Rights Legend for Units of the DoD: Use, duplication or
disclosure by the Government is subject to restrictions as set forth in subparagraph
(c)(1)(ii) of the Rights in Technical Data and Computer Software clause at 252.227-
7013. Adaptec, Inc., 691 South Milpitas Boulevard, Milpitas, California 95035.
11 U.S. Government Restricted Rights Legend for Civilian Agencies: Use, reproduction
or disclosure is subject to restrictions as set forth in subparagraphs (a) through (d) of
the Commercial Computer Software - Restricted Rights clause at 52.227-19 and the
limitations set forth in Adaptec, Inc.’s standard commercial agreement for this soft-
ware. Unpublished - rights reserved under the copyright laws of the United States.
12 General: You acknowledge that you have read this Agreement, understand it, and that
by opening the package you agree to be bound by its terms and conditions. You fur-
ther agree that it is the complete and exclusive statement of the agreement between
Adaptec and you which supersedes any proposal or prior agreement, oral or written,
and any terms of this Agreement or any different terms will be enforceable against
Adaptec unless Adaptec gives its express consent, including an express waiver of the
terms of this Agreement, in a writing signed by an officer of Adaptec. You assume full
responsibility for the use of the Software and agree to use the Software legally and
responsibly. This Agreement shall be governed by California law except as to copy-
right matters which are covered by Federal law. This Agreement is deemed entered
into at Milpitas, California by both parties. Should any provision of this Agreement be
declared unenforceable in any jurisdiction, then such provision shall be deemed to be
severable from this Agreement and shall not affect the remainder hereof. All rights in
the Software not specifically granted in this Agreement are reserved by Adaptec.
Should you have any questions concerning this Agreement, you may contact Adaptec by
writing to: Adaptec, Inc., Legal Department, 691 South Milpitas Boulevard, Milpitas,
California 95035.
20
Contacting Adaptec
Limited 5-Year Warranty
Adaptec, Inc. (“Adaptec”) warrants to the purchaser of this product that it will be free from
defects in material and workmanship for a period of five (5) years from the date of purchase. If the
product should become defective within the warranty period, Adaptec, at its option, will repair or
replace the product, or refund the purchaser’s purchase price for the product, provided it is deliv-
ered at the purchaser’s expense to an authorized Adaptec service facility or to Adaptec.
Repair or replacement parts or products will be furnished on an exchange basis and will either be
new or reconditioned. All replaced parts or products shall become the property of Adaptec. This
warranty shall not apply if the product has been damaged by accident, misuse, abuse or as a result
of unauthorized service or parts.
Warranty service is available to the purchaser by delivering the product during the warranty
period to an authorized Adaptec service facility or to Adaptec and providing proof of purchase
price and date. The purchaser shall bear all shipping, packing and insurance costs and all other
costs, excluding labor and parts, necessary to effectuate repair, replacement or refund under this
warranty.
For more information on how to obtain warranty service, write or telephone Adaptec at 691 South
Milpitas Boulevard, Milpitas, CA 95035, (800) 959-7274.
THIS LIMITED WARRANTY DOES NOT EXTEND TO ANY PRODUCT WHICH HAS BEEN
DAMAGED AS A RESULT OF ACCIDENT, MISUSE, ABUSE, OR AS A RESULT OF UNAUTHO-
RIZED SERVICE OR PARTS.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES WHICH NOW OR
HEREAFTER MIGHT OTHERWISE ARISE RESPECT TO THIS PRODUCT. IMPLIED WARRAN-
TIES, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NON-INFRINGEMENT SHALL (A) HAVE NO GREATER DURATION THAN 5 YEARS
FROM THE DATE OF PURCHASE, (B) TERMINATE AUTOMATICALLY AT THE EXPIRATION
OF SUCH PERIOD AND (C) TO THE EXTENT PERMITTED BY LAW BE EXCLUDED. IN THE
EVENT THIS PRODUCT BECOMES DEFECTIVE DURING THE WARRANTY PERIOD, THE
PURCHASER’S EXCLUSIVE REMEDY SHALL BE REPAIR, REPLACEMENT OR REFUND AS
PROVIDED ABOVE. INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING WITH-
OUT LIMITATION LOSS OF DATA, ARISING FROM BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY ARE NOT THE RESPONSIBILITY OF ADAPTEC AND, TO THE EXTENT PERMIT-
TED BY LAW, ARE HEREBY EXCLUDED BOTH FOR PROPERTY DAMAGE, AND TO THE
EXTENT NOT UNCONSCIONABLE, FOR PERSONAL INJURY DAMAGE.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, AND SOME STATES DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION OR EXCLUSIONS MAY NOT APPLY TO YOU.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
21
|
