Acu Rite Clock Radio 13024 User Manual

Instruction Manual  
Atomic Dual Alarm Clock  
model 13024  
CONTENTS  
Unpacking Instructions ........... 2  
Package Contents .................. 2  
Product Registration ............... 2  
Features & Benefits................. 3  
Clock Setup........................... 5  
Atomic Clock......................... 6  
Set the Time & Date ............... 6  
Placement Guidelines ............. 7  
Using the Clock...................... 8  
USB Charging........................ 8  
Troubleshooting ..................... 9  
Care & Maintenance.............10  
Specifications........................10  
FCC Information ...................10  
Customer Support.................11  
Warranty..............................11  
Questions? Contact Customer Support at  
(877) 221-1252 or visit www.AcuRite.com.  
SAVE THIS MANUAL FOR FUTURE REFERENCE.  
 
Features & Benefits  
FRONT OF CLOCK  
1
1. Snooze Button/Night Light  
2. Alarm #1 ON/OFF Switch  
3. Alarm #1 Setup Button  
INDOOR  
4. UP, DOWN & SET Buttons  
for setup preferences.  
6. Alarm #2 Setup Button  
7. Alarm #2 ON/OFF Switch  
2
3
4
5
6
7
8
9
BACK OF CLOCK  
ALARM  
8. + Brightness Button  
+
+
Increases display brightness.  
-
-
DIMMER  
VOLUME  
9. +/— Alarm Volume  
Adjusts alarm volume.  
10. — Brightness Button  
Decreases display brightness.  
11. USB Charging  
for compatible smartphones.  
CHARGE  
USB DEVICE  
DC 4.5 v  
12. DC 5v Power Input  
10  
11  
12  
14  
13  
15  
BOTTOM OF CLOCK  
(inside battery compartment)  
13. RCC ON/OFF Switch  
Controls synchronization with  
the atomic signal.  
14. ºF/ºC Temperature Units  
15. Zone Button  
Press to select time zone.  
3
 
Features & Benefits  
1
2
3
9
INDOOR  
4
5
7
6
8
1. Date  
6. Alarm #2 Time  
7. Alarm #2 Days Active  
2. Atomic Clock  
Sets itself to the correct time and  
automatically updates for Daylight  
Saving Time.  
Indicates weekday, weekend or every  
day alarm.  
8. Alarm Volume  
3. Atomic Signal Strength  
4. Alarm #1 Time  
9. Indoor Temperature  
5. Alarm #1 Days Active  
Indicates weekday, weekend or every  
day alarm.  
4
 
Clock Setup  
Plug in Power Adapter  
Install or Replace Backup  
Batteries  
2
1
For the best performance, plug  
in the power adapter as the main  
power source for this product.  
1. Remove the battery  
compartment cover.  
2. Insert 3 x AA alkaline  
batteries into the battery  
compartment, as shown.  
Follow the polarity  
(+/-) diagram in the battery  
compartment.  
3. Replace the battery cover.  
Plug in Power  
1
Adapter  
(on back of unit)  
Install or  
2
Replace Backup  
Batteries  
3 AA alkaline  
batteries  
IMPORTANT: Batteries are a backup power source to preserve records in the event of a  
power outage. Power adapter recommended as the primary power source to enjoy the full  
functionality of the product.  
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE  
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.  
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be  
used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used  
batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire,  
as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge  
non-rechargeable batteries. DO NOT short-circuit the supply terminals.  
5
 
Atomic Clock (RCC)  
AcuRite atomic clocks use a radio-controlled signal (RCC) to synchronize to the  
correct time broadcast by the National Institute of Standards and Technology  
(NIST) Radio Station WWVB, located near Fort Collins, Colorado. WWVB  
broadcasts the current time and date with split-second accuracy.  
The atomic clock and calendar will maintain the correct time and date, and  
automatically update for daylight saving time to provide the most accurate  
timekeeping standard possible.  
When the RCC button, located under the battery compartment cover, is set to  
ON, the clock will automatically search for the atomic clock signal.  
To manually search for the atomic signal, make sure the RCC button is set to  
ON, then press AND HOLD the “ “ button.  
Please note: Signal reception is normally better at night and when the weather  
is clear. The atomic signal generally takes a few hours to synchronize, so it is  
important to manually set the time and date after powering on the clock.  
Set the Time & Date  
Press and hold the “  
” button, located on the front of the clock, to enter SET  
MODE. Once in SET MODE the preference you are currently setting will blink  
on the clock.  
To adjust the currently selected (flashing) item, press and release the “ ” or  
“ buttons (press and HOLD to fast adjust).  
To save your adjustments, press and release the “  
preference. The preference set order is as follows:  
” button to adjust the next  
TIME ZONE (PST MST CST EST AST HAST AKST)  
AUTO DST ON/OFF*  
CLOCK HOUR  
CLOCK MINUTE  
CALENDAR MONTH  
CALENDAR DATE  
CALENDAR YEAR  
You will automatically exit SET MODE if no buttons are pressed for 5 seconds.  
Enter SET MODE at any time by pressing the “ ” button.  
*If you live in an area that observes daylight saving time, DST should be set to  
ON, even if it is not currently Daylight Saving Time.  
6
 
Alarm Clock Placement  
Place alarm clock in a dry area free of dirt and dust. To help  
ensure an accurate indoor temperature measurement, be sure to  
place the clock away from heat sources or vents.  
INDOOR  
Important Placement Guidelines  
• To ensure accurate temperature measurement, place out of direct  
sunlight and away from any heat sources or vents.  
• To maximize atomic signal reception, place unit away from large metallic  
items, thick walls, metal surfaces, or other objects that may limit radio  
communication.  
• To prevent wireless interference, place unit at least 3 ft (.9 m) away  
from electronic devices (TV, computer, microwave, radio, etc.).  
7
 
OPERATION  
Using the Clock  
Set the Alarm Time  
Slide Alarm #1 and/or Alarm #2 switch ON (alarm time cannot be adjusted if  
the alarm is OFF).  
1
Press and release the “  
MODE.  
” or the “  
” button to enter ALARM SET  
2
To adjust the currently selected (flashing) item, press and release the “ ” or  
“ buttons (press and HOLD to fast adjust).  
To save your adjustments, press and release the “  
1” or “  
“ button to  
2
adjust the next preference. The preference set order is as follows:  
ALARM CLOCK HOUR  
ALARM CLOCK MINUTE  
ALARM EVERY DAY or WEEKDAY ONLY or WEEKEND ONLY  
You will automatically exit ALARM SET MODE if no buttons are pressed for 5  
seconds. Enter ALARM SET MODE at any time by pressing the “ ” or  
“ button.  
1
2
Backlight  
During power adapter use, press the Snooze button for momentary backlight  
at 100% brightness. During battery-powered use, press any button for  
momentary backlight.  
The backlight MAY turn off at 2:00AM and 3:00 AM to acquire the atomic  
clock (RCC) signal.  
USB Charging  
Charge your mobile device by plugging your device’s USB power cord (not  
included) into the USB charging port on the back of the clock.  
USB charging is only available during power adapter use; USB charging is not  
active when operating on battery power only.  
ALARM  
+
+
Note: Follow the manufacturer’s instructions for your  
mobile device(s) to determine compatibility with the USB  
charging feature on this product. Some devices may not  
support USB charging or may require a higher power  
rating than this product provides. Observe the charging  
status on your device. Ensure your device is working  
properly before attempting to charge.  
-
-
DIMMER  
VOLUME  
CHARGE  
USB DEVICE  
DC 4.5  
v
8
 
Troubleshooting  
• The backlight may automatically turn off for 10 minutes  
at 2:00am and 3:00am to acquire the atomic clock  
signal.  
• Verify power adapter is plugged in.  
• Check that the batteries are installed correctly. Batteries  
may need to be replaced.  
• Increase brightness using +/– buttons, located on the  
back of the clock.  
• The optimum viewing angle for this product is from  
slightly above it.  
Clock is too dark, hard  
to read or doesn’t  
work  
• Reset the unit by unplugging the power supply from the  
wall outlet and remove any batteries that are installed.  
This will reset the alarm to the original factory settings.  
Time and date will need to be entered after a reset.  
• Make sure the clock is placed out of direct sunlight and  
away from any heat sources or vents  
(see page 7).  
Inaccurate  
temperature  
For additional troubleshooting, please visit:  
Atomic signal or time  
syncing problems  
If your AcuRite product does not operate properly after trying  
(877) 221-1252 for assistance.  
9
 
Care & Maintenance  
Clock Care  
Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep  
away from dust, dirt and moisture. Clean ventilation ports regularly with a  
gentle puff of air.  
Specifications  
TEMPERATURE RANGE  
POWER  
32ºF to 99ºF, 0ºC to 37ºC  
5v power adapter  
3 x AA alkaline batteries (for backup only)  
FCC Information  
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:  
1- This device may NOT cause harmful interference, and  
2- This device must accept any interference received, including interference that may cause undesired operation.  
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the  
user’s authority to operate the equipment.  
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC  
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-  
ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. However, There is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning  
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and the receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.  
Such modifications could void the user authority to operate the equipment.  
This device complies with Industry Canada licence-exempt RSS standard(s).  
Operation is subject to the following two conditions:  
(1) This device may not cause interference, and  
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.  
10  
 
Customer Support  
AcuRite customer support is committed to providing you with best-in-  
class service. For assistance, please have the model number of this  
product available and contact us in any of the following ways:  
(877) 221-1252  
24/7 support at www.AcuRite.com  
Installation Videos  
Instruction Manuals  
Replacement Parts  
Register your Product  
Support User Forum  
Submit Feedback & Ideas  
PRODUCT MUST BE REGISTERED  
TO RECEIVE WARRANTY SERVICE  
IMPORTANT  
PRODUCT REGISTRATION  
Register online  
to receive 1 year  
warranty protection  
www.AcuRite.com  
Register a Product  
Limited One Year Warranty  
warranty will not be breached, and Chaney will give no credit  
for products it manufactures which have received normal wear  
and tear, been damaged (including by acts of nature), tampered,  
abused, improperly installed, damaged in shipping, or repaired  
or altered by others than authorized representatives of Chaney.  
At AcuRite, we proudly uphold our commitment  
to quality technology. Chaney Instrument Co.  
warrants that all products it manufactures to  
be of good material and workmanship, and to  
be free of defects when properly installed and  
operated for a period of one year from the date  
of purchase.  
The above-described warranty is expressly in lieu of all other  
warranties, express or implied, and all other warranties are  
hereby expressly disclaimed, including without limitation the  
implied warranty of merchantability and the implied warranty  
of fitness for a particular purpose. Chaney expressly disclaims  
all liability for special, consequential or incidental damages,  
whether arising in tort or by contract from any breach of this  
warranty. Some states do not allow the exclusion or limitation  
of incidental or consequential damages, so the above limitation  
or exclusion may not apply to you. Chaney further disclaims all  
liability from personal injury relating to its products to the extent  
permitted by law. By acceptance of any of Chaney’s products,  
the purchaser assumes all liability for the consequences arising  
from their use or misuse. No person, firm or corporation is  
authorized to assume for Chaney any other liability in connection  
with the sale of its products. Furthermore, no person, firm or  
corporation is authorized to modify or waive the terms of this  
paragraph, and the preceding paragraph, unless done in writing  
and signed by a duly authorized agent of Chaney. This warranty  
gives you specific legal rights, and you may also have other  
rights which vary from state to state.  
We recommend that you visit us at  
your product. However, product registration  
does not eliminate the need to retain your  
original proof of purchase in order to obtain  
warranty benefits.  
Chaney Instrument Co. warrants that all products it manufactures  
to be of good material and workmanship, and to be free of  
defects when properly installed and operated for a period of  
one year from the date of purchase. Remedy for breach of this  
warranty is limited to repair or replacement of the defective  
item(s). Any product which, under normal use and service, is  
proven to breach the warranty contained herein within ONE  
YEAR from date of sale will, upon examination by Chaney,  
and at its sole option, be repaired or replaced by Chaney.  
Transportation costs and charges for returned goods shall  
be paid for by the purchaser. Chaney hereby disclaims all  
responsibility for such transportation costs and charges. This  
For in-warranty claims: Chaney Instrument Co.  
965 Wells St., Lake Geneva, WI 53147  
11  
 
Weather  
Stations  
Temperature  
& Humidity  
Weather  
Alert Radio  
Kitchen  
Thermometers  
& Timers  
Clocks  
It’s more than accurate, it’s  
AcuRite offers an extensive assortment of precision instruments,  
designed to provide you with information you can depend on to  
Plan your day with confidence.  
www.AcuRite.com  
©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark  
of the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and  
copyrights are the property of their respective owners. AcuRite uses patented  
Printed in China  
13024 INST 091713  
 

3Com Network Router 111 User Manual
Advantech Computer Hardware PCM 9587 User Manual
AEG Dishwasher 5071 User Manual
AEG Range Ovens User Manual
Agri Fab Spreader 45 02113 User Manual
Aiphone Car Video System KB MV2 User Manual
Aiphone Intercom System 514426 A 0611YZ User Manual
Alpine GPS Receiver NVE M300 User Manual
Audiovox Automobile Electronics CA 5150 User Manual
Bacharach Carbon Monoxide Alarm R 600a User Manual