ACCUSPLIT®
ALLIANCE™ 625M8D
3. Press A to start countdown timing
MULTIMODETIMER/STOPWATCH
4. Press E to show the time from start ( )
5. Press E again to return to countdown timing ( )
6. Press A again to stop counting
OPERATING INSTRUCTIONS
7. Press B to return to the original setting
8. When time is up, the unit will beep once, then start
counting again.The number of cycles completed is
recorded in brackets in upper left of display.
RECALL
UP/DOWN
E
B
A
RESET/SPLIT
START/STOP
DUAL DISPLAY COUNTDOWNTIMER
1. Press C to move the cursor to point to
DUAL
2. Press E to change the dual display timer mode (SU
or Id or UP)
3. Press D to adjust the timer on the lower display
Press D again to adjust the timer on the upper display
C MODE
•
•
•
Press B to set hours, E to set minutes, A to set seconds
Press A & B at the same time to reset digits to zero
Press D again to complete the settings
4. SU -Two countdown timers work simultaneously
•
•
•
Press A to start
Press A to stop (STOP: flashes)
Press B to reset to the original settings
ROTARY
SWITCH
D
SET
Id -Two countdown timers work independently
•
•
•
Press A to start/stop lower display
Press B to start/stop upper display
Press A & B at the same time to reset to the original
settings
UP -Two count up timers work independently
INTRODUCTION
•
•
•
Press A to start/stop lower display (STOP: flashes
when stopped)
Press B to start/stop upper display (STOP: flashes
when stopped)
This unit has five modes: Stopwatch, Auto Repeat Countdown
Timer, Dual Display CountdownTimer, Pacer, and Preset
CountdownTimer.
Press C (MODE) to change between modes. Note:Timing must
be stopped and reset to zero to change modes.
Press A & B at the same time to reset to zero
PACERWITH COUNT UPTIMER
1. Press C to move the cursor to point to
2. Press D to adjust the frequency
MEMORY STOPWATCH
PACE
SPLITTIMING
1. Press C to move the cursor to point to
2. Press A to start stopwatch
3. Press B repeatedly to remember the last 8 splits
•
•
Press A to increase the digits
Press B to decrease the digits
3. Press A to start pacer
4. Press A again to the stop
5. Press B to reset to zero
6. Press E to turn the pacer’s beep ON or OFF
and the symbol (((•))) will appear or disappear
7. Upper display shows count up timer
•
•
Lower display shows cumulative split and upper
display shows lap split
After 5 seconds, the unit will unlock splits to display
current running split time
4. Press E to recall the last 8 splits
5. Press A to stop counting
6. Press B to reset to zero
16 PRESET COUNTDOWNTIMER
1. Press C to move the cursor to point to (1-60)
2. Turn the rotary switch to the desired minutes (1-60)
3. Press A to start countdown timing
4. Press A again to stop countdown timing
5. Alarm Sounds
START-STOPTIMING
1. Press C to move the cursor to point to
2. Press A to start counting
3. Press A repeatedly to remember the last 8 time-cuts
4. Press E to recall the last 8 times-outs
5. Press A to stop counting
6. Press B to return to the original setting
6. Press B to reset to zero
To Show Count Up Timing
1. When the time is not up.
a. Press E to check elapsed time ( )
b. Press E again to return to countdown ( )
2. When the time is over,
AUTO REPEAT COUNTDOWNTIMER
1. Press C to move the cursor to point to AUTO
2. Press D to enter set mode
a. Press E to check the time from start ( flashes)
b. Press E again to show overtime ( flashes)
•
•
Press B to set hours, E to set minutes, A to set seconds
Press A & B at the same time to reset digits to zero
|