ACCUSPLIT®EAGLE
AE120XLM
PEDOMETER
ACCUSPLIT, Inc.
6120 Stoneridge Mall Rd., Suite 210
Pleasanton, CA 94588 USA
800-965-2008 • 925-226-0888 • FAX 925-463-0147
Eat Right! Walk More! Live Well!
The ACCUSPLIT Lifestyle
970-083
Sept 07
Operating Instructions
Functions
Key Features
•
•
•
Step counter.
•
Built around the Japanese-made JW200 PedometerEngine™
Step Sensor, the current gold standard for accuracy.
Automatic ActivityTimer.
Trip andTotal memories for Steps, and ActivityTime.
•
•
Extra Large Digits.
The ACCUSPLIT exclusive case makes this the slimmest
available pedometer built around the JW200 Step Sensor.
For complete Function Specifications, go to page 29.
•
•
Chromed, Spring Steel clip resists breakage.
Case includes two leash slots, for attaching safety leash
on either side. Made from tough polycarbonate plastic.
•
•
Total Steps Memory counts to 10,000,000 steps!
Step filter, can be set from 0-5 steps to further increase
accuracy.
2
3
HOWTO OPENYOUR PEDOMETER
See diagrams at right.
USE IT NOW!
Your pedometer is preset with standardized settings
that allow you to use it now!You can customize the
settings later. Skip to pages 8-11 to use it now!
The cover must be closed for the
pedometer to work.
4
5
Getting Acquainted
Mode
indicator
•
•
•
Press the MODE button to cycle through the display
modes (Steps, ActivityTime).
DIGI-WALKERXL.COM
STEP TIME
See pages 11-12 and Specifications for details.
Steps
SET
M
Press MEMORY
button to switch back and forth
Counted
betweenTrip andTotal memory displays.
See pages 12-14 for a complete explanation.
The RESET button sets your counts back to zero.
See page 15 for details.
MODE Button
120
M
XL
MODES
JW200
S3-
S1,S2,S4
S3+
•
•
STEP: STEP mode shows step count.
TIME: AUTO ACTIVITYTIMER MODE shows total
activity time in min and sec.
MEMORY Button
RESET Button (yellow)
6
7
OTHER SETTINGS
The Step Filter setting is accessed through a special “deep
set” mode.
CHANGING STEP FILTER SETTING
While the JW200 PedometerEngine™ Step Sensor is extremely
accurate, some people like to have the ability to filter out false
steps. Therefore, the unit has a variable setting step filter, to
allow fine-tuning to your specific preferences.You can set the
value to any value from 0 – 5 steps. For example, if the filter is
set to “3”, the unit will wait to start counting steps until more
than three steps have been taken in less than five seconds.
ACCUSPLIT products use a common setting procedure
known as “S1- S2-S3-S4.” Here’s how it works:
Press S1 for 2 seconds: Enter the SET mode
Press S2: Change the field to be set
Press S3: Change the field value
Press and hold the S1 (MEMORY) button for 4 seconds.The
screen will display a single digit. Press S3+ (MODE) or S3–
(RESET) to change the Step Filter Setting. Press and hold S4
(Memory) for 2 seconds to exit Deep Set Mode.
Press S4 for 2 seconds: Exit the SET mode
Note: The unit will save any changes and exit set mode after
30 second unattended.
16
17
REPLACINGTHE BATTERY AND MASTER RESET
When the display starts to dim or goes blank, it is time to
replace the battery.
DIGI-WALKERXL.COM
STEP TIME
Can be set
from 0-5
steps
SET
If the display is not uniformly dim or blank, and appears to
display “erroneous data”, do a Master Reset by pressing all
3 buttons simultaneously for 3 seconds and then release.
The display should go blank, then turn all segments on, then
display 0 steps in Step Mode.
120
M
XL
Note: All the settings will return to their default setting values.
If you need to change the battery, the settings will also revert
to default settings.
JW200
S3-
S1,S2,S4
S3+
Set Step Filter set point
18
19
To replace the battery:
SPECIFICATIONS, FEATURES, and FUNCTIONS
Description of Functions
1. Insert a coin into the slot on the
bottom of the case, and twist to
loosen the faceplate. Remove
faceplate and set aside.
•
•
Counts Steps up to 99,999 then rollover.
Has aTotal Memory for Steps that counts up to 99,999,999
steps, then rollover.
2. Locate the battery holder as seen
on sketch. Pull out the old battery,
and push a new LR-44 battery into the holder,
with positive terminal (+) facing up.
•
CountsTime spent in step activity, up to 999 Min 59 sec,
then rollover. Automatically counts whenever step activity
is occurring.
Has aTotal Memory for ActivityTime that counts up to
99,999 minutes, then rollover.
Battery
•
•
3. Snap faceplate back into place, hooking the bottom
two tabs first, then closing by pressing together at the
top two tabs.
Adjustable Step Filter (default setting is 1 step, but can
be set from 0-5 steps) to increase step count accuracy.
20
21
INDEX
Email (preferred)
User
REGISTER NOW Please return
your AE120XLM Registration to
the Repair Center address in the
warranty, and we will let you know
about future products.
Battery, replacing . . . . . . . . . . . . . . . . . . 19-20
Current day’s results, viewing . . . . . . . . . . .11
Memory, resetting . . . . . . . . . . . . . . . . . . . 15
Open your pedometer . . . . . . . . . . . . . . . . . 4
Safety Leash . . . . . . . . . . . . . . . . . . . . . . . 9-10
Setting up pedometer. . . . . . . . . . . . . . . . 6-11
Step Filter Setting, change. . . . . . . . . . .16-18
TOTAL vsTRIP Memories . . . . . . . . . . . .12-13
Wearing pedometer . . . . . . . . . . . . . . . . . . . 8
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
NO-PROOF-OF-PURCHASE LIMITEDWARRANTY
Free service for first year of ownership;
$12 fee for service thereafter. See label inside unit for date.
22
23
|