ATN PS-22
NIGHT VISION ATTACHMENT
u s e r ` s g u i d e
Important Export Restrictions! Commodities, prod-
ucts, technologies and services contained in this manual
are subject to one or more of the export control laws and
regulationsoftheU.S. Governmentandtheyfallunderthe
control jurisdiction of either the US Department of State
or the US BIS-Department of Commerce. It is unlawful
and strictly prohibited to export, or attempt to export or
otherwise transfer or sell any hardware or technical data
or furnish any service to any foreign person, whether
abroad or in the United States, for which a license or writ-
ten approval of the U.S. Government is required, without
first obtaining the required license or written approval
from the Department of the U.S. Government having
jurisdiction. Diversion contrary to U.S. law is prohibited.
APPLICATION
The PS-22 is attachment for daytime riflescopes with 1x-6x (2.5x-4x are optimal) magnification that
converting scope into a high quality, very accurate night vision weapon sight.
The PS-22 mounts in front of daytime scope. Re-zeroing of scope not required. PS-22 comes standard
with 7/8” weaver mount. There is also Adapter for ARMS quick release mount. Optional Ring Adapters
allows to mount unit onto the objective of the day scope (25...58mm diameter). The IR illuminator can be
mounted onto the optional Picatinny Rail.
The PS-22 utilizes a 2nd Gen.+ or 3rd Gen. Image Intensifier Tube. This ingenious setup allows the
shooter to go from day to night in less then 30 seconds without tools, without changes in eye relief and
remain zeroed all around the clock.
The PS-22 is a complex optical-electronic system. The device contains an image intensifier tube as-
sembly with an integrated high voltage power source and the three volt battery housing.
Objective lens protective cover is intended to protect objective lens from dust, scratches and high-level
illumination. The pinhole in cover allows the user to check the operation ability of the device in highlight
conditions.
The device has a built in Automatic Brightness Control. This system automatically adjusts the bright-
ness of Image Intensifier Tube to the optimal level.
The Automatic Highlight Protective System analyzes light exposure. If high light exposure is kept more
than 10 seconds the device automatically will off.
NOTE: The automatic highlight protective system and automatic brightness control system do not pro-
tect a sight from damage by bright light sources (a fire, headlights of the automobile, lanterns, etc.). Do
not point the device at a bright light source.
FEATuRES
• Easily changes daytime scope to Night Vision
• Mounts in front of daytime scope, no re-zeroing required
• Available in 2nd + and 3rd generation
• Multi-coated all glass optics
• Fast catadioptic front lens system
• Large 40mm eyepiece/output window
• Light weight and rugged
• Comes standard with 7/8” weaver mount
• Adapter for ARMS quick release mount included
• Optional adapters for mountinng onto the objective of the day scope (25...58mm diametr)
SPECIFICATIONS
Magnification...................................................................................................................1X
Intensifier Tube.................................................................................. 2nd Gen+ or 3rd Gen
Lens System............................................................................................... F1:1.44, 80mm
FOV ................................................................................................................................13°
Power Supply ..........................................................................one 3 Volt Battery(CR123A)
Range Of Focus ............................................................................................10m to Infinity
Battery Life............................................................................................................50 hours
Operating Temperature...............................................................................-40°C to +50°C
Waterproof................................................................................................... 10m for 30min.
Dimensions .................................................................................139mm X 80mm X 72mm
Weight ........................................................................................................................ 0.6kg
2
MOuNTING
Mounting onto the Weaver rail with 7/8”
Weaver Mount
1) Mount the 7/8” Weaver Mount onto the body of
PS-22 with 2 screws M4x7 from set.
2) Unscrew the protective back cap from PS-22.
3) Screw the Light Screen into the thread in back
side of unit.
4) Slightly loosen the fixing screws of mount.
5) Place the PS-22 on the weaver rail of the fire
arm before objective of daytime scope on the
minimal distance from it. The optical axes of PS-
22 and daytime scope must have divergence not
more than 3mm. High of optical axe of the PS-22
under weaver rail is 40mm with standard mount
and corresponded ATN 3.5x26 scope.
6) Tighten the fixing screws.
NOTE: Fixing screws may need to be tightened
after continuous shooting.
Mounting onto the Weaver rail with A.R.M.S.
Mount
1) Mount the Adapter onto the body of PS-22 with
2 screws M4x7 from set.
2) Mount the PS-22 with Adapter onto the
A.R.M.S.#10 or A.R.M.S.#19 ACOG with 2
screws M5x8.
3) Unscrew the protective back cap from PS-22.
4) Screw the Light Screen into the thread in back
side of unit.
5) Slightly loosen the fixing screws or levers of
mount.
6) Place the PS-22 on the weaver rail of the fire
arm before objective of daytime scope on the
minimal distance from it. The optical axes of PS-
22 and daytime scope must have divergence not
more than 3mm. High of optical axe of the PS-22
under weaver rail is 49mm with A.R.M.S.#19
ACOG.
7) Tighten the fixing screws or levers of mount.
NOTE: Fixing screws may need to be tightened
after continuous shooting.
Mounting onto the objective of the day scope
with Optional Ring Adapters
1) Unscrew the protective back cap from PS-22.
2) Screw the Ring Adapter into the thread in back
side of unit.
3) Slightly loosen the fixing screws of Ring
Adapter.
4) Put the Insert into the Adapter
3
5) Slide the PS-22 with Adapter onto the objective of day scope.
6) Tighten hard the fixing screws of the Ring Adapter.
7) Mount the Picatinny Rail Adapter onto the body of PS-22 with 2 screws M4x7 from set.
8) Place the IR Illuminator onto the Picatinny Rail.
Optional Ring Adapters allows to mount unit onto the objective of the day scope
(25...58mm diameter)
Ring Adapter #
1
Diametr of scope lens
(insert size)
Examples of scops
25.4
30
Leupold 1,5-5x20 PR
Leupold 1,5-5x20 MR/T M2,
Zeiss 1,1-4x24 T
2
3
38
42
Meopta Artemis 2000 4x32
Leupold 3-9x36,
Kahles 4x36
46.5
48
Leupold 3,5-10x40
Zeiss1,5-6x42,
Swarovski PV-N 2,5-10x42
fro 48.7 to 49.0
Meopta Artemis 3000 3-9x42
Meopta Artemis 3000 4-12x40
Schmidt@Bender 10x42 PMII
Zeiss 2,5-10x50
49.5
50
4
56
57
Schmidt@Bender 3-12x50
Leupold 4,4-14x50
58.4
OPERATION
• Place the PS-22 before objective of daytime scope.
• Put power switch in OFF-position.
• Install the battery into the housing with the polarity order as shown on the devices body. The bat-
tery is 3 volt lithium battery (CR123A).
• Turn the devise on by rotation the power switch into the ON-position. The greenish-lit screen of
the image tube (when looking through the eyepiece) means that the image tube is powered.
Do not turn the unit on in the daytime without the protective lens cap on.
• Next, remove the lens cap.
• Observe the scene and adjust the focusing of PS-22 by rotation the focusing ring. Also focusing
daytime scope for optimal clarity.
• Turn on the illumination of day scope reticle (if it present) and adjust the brightness.
• Put power switch in OFF-position for turn PS-22 off.
4
WARNINGS AND CAuTIONS
• Always remember to turn off the PS-22 when it is not in use. If you do not plan on using your unit for
a period of more than 10 days, you should remove the batteries.
• Keep lens cap on when not in use.
• Avoid contact with dust, steam, and gas.
• The PS-22 is not harmful to the user or the environment.
• Do not disassemble: it will void your warranty.
• Never use in daylight without the lens cap on.
• Never point the PS-22 at a bright light source. If the scope shuts off automatically after directing it
at a bright light source, turn the unit off and wait 1 - 2 minutes before turning the unit back on.
• Adverse atmospheric conditions such as fog, smog, or haze and a lack of ambient light (moon or
starlight) may diminish the effective viewing distance. All technical data for this unit was compiled
in a controlled environment.
TROubLE SHOuTING
Q: Flashes, flickers or clicking occur while operating
S: If it occurs within the first five minutes of inserting new batteries, it is normal and the device will
resume normal operation soon thereafter. If it occurs for more than 10 minutes, contact for service
instructions.
Q: Dark spots on screen.
S: These are either cosme tic blemishes in the intensifier tube or dust particles.
Q: Screen becomes darker than at previous use.
S: Replace batteries. If problem persists, contact your dealer or other authorized service representa-
tive for service instructions.
Q: Image not clear.
S: Adjust objective lens, and/or the eyepiece.
5
ATN LIMITED LIFETIME WArrANTy
LIMITATIoN oF LIAbILITy
ATN Limited Lifetime Warranty is limited to the
product being free of manufacturer defects
in materials and workmanship. In regards to
night vision products the image intensifier
tube is warranted to be free from manufacturer
defects for a period of 2 years (defects do not
include minor black spots or blemishes in view-
ing area). ATN will repair or replace said prod-
ucts or part thereof which upon inspection by
ATN are found to be defective in materials or
workmanship. As a condition to the obligation
of ATN to repair or replace said product, the
product must be returned to ATN together with
proof-of-purchase satisfactory to ATN. This
warranty does not cover damages caused by
misuse or improper handling. This warranty is
null and void if modification or maintenance is
provided by parties other than ATN Corp. In the
event a defect that is covered by the foregoing
warranty occurs during the applicable period
stated above, ATN, at its option, will either re-
pair or replace the product, and such action on
the part of ATN shall be the full extent of ATN’s
liability, and the Customer’s sole and exclu-
sive remedy. This warranty does not cover a
product (a) used in other than its normal and
customary manner; (b) subjected to misuse;
(c) subjected to alterations, modifications or
repairs by the Customer of by any party other
than ATN without prior written consent of ATN;
(d) special order or “close-out” merchandise
or merchandise sold “as-is” by either ATN or
the ATN dealer; or (e) merchandise that has
been discontinued by the manufacturer and
either parts or replacement units are not avail-
able due to reasons beyond the control of ATN.
ATN shall not be responsible for any defects or
damage that in ATN’s opinion is a result from
the mishandling, abuse, misuse, improper
storage or improper operation, including use
in conjunction with equipment which is electri-
cally or mechanically incompatible with or of
inferior quality to the product, as well as fail-
ure to maintain the environmental conditions
specified by the manufacturer. CuSTOMER
IS HEREbY NOTIFIED THAT OPERATION
OF THE EQuIPMENT DuRING DAYLIGHT
HOuRS OR uNDER ANY EXCESSIVE LIGHT
CONDITIONS MAY PERMANENTLY DAM-
AGE THE INTERNAL COMPONENTS OF
THE uNIT AND SAID DAMAGE WILL NOT
bE COVERED uNDER THIS WARRANTY.
This warranty is extended only to the original
purchaser. Any breach of this warranty shall be
waived unless the customer notifies ATN at the
address noted below within the applicable war-
ranty period.
ATN will not be liable for any claims, actions,
suits, proceedings, costs, expenses, dam-
ages or liabilities arising out of the use of this
product. Operation and use of the product are
the sole responsibility of the Customer. ATN’s
sole undertaking is limited to providing the
products and services outlined herein in ac-
cordance with the terms and conditions of this
Agreement. The provision of products sold and
services performed by ATN to the Customer
shall not be interpreted, construed or regard-
ed, either expressly or implied, as being for the
benefit of or creating any obligation toward any
third party of legal entity outside ATN and the
Customer; ATN’s obligations under this Agree-
ment extend solely to the Customer. ATN’s li-
ability hereunder for damages, regardless
of the form or action, shall not exceed the
fees or other charges paid to ATN by the
customer or customer’s dealer. ATN shall
not, in any event, be liable for special, indi-
rect, incidental or consequential damages,
including, but not limited to, lost income,
lost revenue or lost profit, whether such
damages were foreseeable or not at the
time of purchase, and whether or not such
damages arise out of a breach of warranty,
a breach of agreement, negligence, strict li-
ability or any other theory of liability.
PRODuCT WARRANTY REGISTRATION
In order to validate the warranty on your prod-
uct, ATN must receive a completed Product
Warranty Registration Card for each unit.
Please complete the form below and immedi-
ately mail it to our Service Center: ATN Corp. ,
20 S. Linden Ave. Suite 1B, South San Francis-
co, CA 94080. Products qualifying for warranty
repair will be either repaired or replaced within
10 business days of receipt of merchandise un-
less the customer is notified otherwise.
ObTAINING WARRANTY SERVICE
To obtain warranty service on your unit, take
or send the product, postage paid, with a copy
of your sales receipt to our service center, ATN
Corporation at the address noted above. All
merchandise must be fully insured with the
correct postage; ATN will not be responsible
for improper postage or, missing or damaged
merchandise during shipment.
The customer understands and agrees that ex-
cept for the foregoing warranty, no other war-
ranties written or oral, statutory, expressed or
implied, including any implied warranty of mer-
chantability or fitness for a particular purpose,
shall apply to the product. All such implied war-
ranties are hereby and expressly disclaimed.
6
For customer service and technical support, please contact
American Technologies Network Corp.
North American Office
20 S. Linden Ave. Suite 1B, South San Francisco, CA 94080
phone: 800-910-2862, 650-875-0130; fax: 650-875-0129
European Office
phone: 44(0)870-0111286, fax: 44(0) 845-3349142
The following countries can use our
toll free number 00 800 9102-8620
Austria, France, Germany, Holland, Italy, Spain, Sweden, Switzerland
©2006 ATN Corporation
|