Quick Start Guide
NI-700 NetLinx Integrated Controller
For more detailed installation, configuration, programming, file transfer, and
operating instructions, refer to the NetLinx Integrated Controllers Instruction
NI-700 Specifications (Cont.)
Rear Panel:
•
•
RS-232/422/485 (Ports 1 & 2): Two RS-232/422/485 control ports
using DB9 (male) connectors with XON/XOFF (transmit on/transmit
off), CTS/RTS (clear to send/ready to send), and 300-115,200 baud.
IR RX (Port 5): This single port is used to connect one or more
(8 maximum) IRX-SM+ swivel mount or IRX-DM+ Decora mount IR
receivers.
The IR RX port functions using AMX IR codes (38 KHz and 455 KHz)
and works ONLY with AMX IR Receivers such as the IRX-DM+ and
IRX-SM+.
Digital I/O (Port 4): Four-channel binary I/O port for contact closure
with each input being capable of voltage sensing. Input format is
software selectable with interactive power sensing for IR ports.
IR/Serial (Port 3): This single port is capable of generating IR with the
use of an IR emitter (while in IR mode). This port can support
high-frequency carriers of up to 1.142 MHz and can also generate IR
with no carrier frequency.
(front)
(rear)
•
•
•
•
AXlink LED: One green LED indicates the state of the AXlink port.
AXlink port: 4-pin 3.5 mm mini-Phoenix (male) connector provides data
and power to external control devices.
•
Ethernet port: LEDs show communication activity, connections,
speeds, and mode information:
L/A-link/activity - Green LED lights On when the Ethernet cables are
connected and terminated correctly and blinks when receiving
Ethernet data packets.
FIG. 1 NI-700 NetLinx Integrated Controller (front and rear views)
SPD-speed - Yellow LED lights On when the connection speed is
100 Mbps and turns Off when the speed is 10 Mbps.
•
Power port: 2-pin 3.5 mm mini-Phoenix (male) connector
Overview
Included
Accessories:
•
•
•
•
•
•
NI-700 Quick Start Guide (93-2105-03)
The NI-700 unit (FG2105-03) is geared to meet the specific control and
automation needs of a single room environment, where both price and
functionality are the driving requirement. This product is configured to control a
limited number of video players, projectors, lighting, thermostats, and other
electronic equipment. The NI-700 provides support for 1 IR/Serial Output port,
2 RS-232/RS-422/RS-485 ports, 4 Digital Input/Output ports, and 1 IR RX port.
One 6-pin 3.5 mm mini-Phoenix female I/O connector (41-5063)
One 4-pin 3.5 mm mini-Phoenix female AXlink connector (41-5047)
One 2-pin 3.5 mm mini-Phoenix female PWR connector (41-5025)
One CC-NIRC IR Emitter (FG10-000-11)
OpenSSL Warranty and Licensing Information (93-2105-05)
Optional
Accessories:
•
•
•
•
•
•
•
•
•
•
2-pin Black Male Phoenix Connector (3.5mm) (41-5026)
AC-RK Accessory Rack Kit (FG515)
CC-NIRC IR cables (FG10-000-11)
CC-NSER IR/Serial cables (FG10-007-10)
CSB Cable Support Bracket (FG517)
PSN2.8: Power supply (FG423-17)
PSN4.4: Power supply(FG423-45)
PSN6.5: Power supply (FG423-41)
STS, Serial To Screw Terminal (FG959)
Surface Mount Bracket Accessory (FG525)
ATTENTION!
When working with the NI-700 Integrated Controller, verify you are using the
latest version of NetLinx Studio v 2.2 build 78 or higher (available for download
NI-700 Specifications
Port Assignment and Functionality
NetLinx Port Assignments
Dimensions (HWD):
•
•
1.58" x 5.54" x 5.12" (4.01 cm x 14.10 cm x 13.00 cm)
1 rack unit high
Port
ICSP Port #
Power:
•
280 mA @ 12 VDC
Serial Port 1
Serial Port 2
IR Port
1
2
3
4
5
Memory:
•
•
•
•
32 MB SDRAM
16 MB Flash chip
512 Kb of Non-volatile SRAM
Refer to the NetLinx Integrated Controllers Instruction Manual for more
information.
I/O Port
Microprocessor:
Weight:
•
•
•
•
304 MIPS using a PowerPC™ processor
1.30 lbs (0.59 kg)
IR RX Port
Enclosure:
Front Panel:
Metal with black matte finish
Ethernet Ports used by the NI Controller
Ethernet Port Usage
Program Port: RS-232 DB9 connector (male) can be connected to a
DB9 port on a PC. This port can be used with both Serial and NetLinx
commands.
Configuration DIP Switch: Use this DIP switch to set the communication
parameters for the Program port.
IR RX LED: Red LED lights to indicate when IR data is being received
via the rear IR RX port.
IR LED: Red LED lights to indicate transmission of IR or Serial data
via the rear IR port.
I/O LEDs: Four yellow LEDs light when the rear I/O channels 1-4 are
active. LED indicator for each I/O port reflects the state of that
particular port.
Serial LEDs: Two sets of red and yellow LEDs light to indicate the rear
DB9 Ports 1 & 2 are transmitting or receiving RS-232, 422, or 485
data. These LEDs do not reflect changes in either the RTS or CTS
when hardware handshaking is used.
LINK/ACT: Green LED lights when the Ethernet cable is connected and
an active link is established. This LED also blinks when receiving
Ethernet data packets.
Status: Green LED lights to indicate that the system is programmed
and communicating properly.
Output: Red LED lights when the Controller transmits data, sets
channels On and Off, sends data strings, etc.
•
•
•
•
Port type
Description
Standard Port #
ICSP
Peer-to-peer protocol used for both Master-to-Master and
Master-to-device communications.
1319 (UDP/TCP)
Telnet
HTTP
The NetLinx Telnet server provides a mechanism to
configure and diagnose a NetLinx system.
23 (TCP)
The Master has a built-in web server that complies with the 80 (TCP)
HTTP 1.0 specification and supports all of the required
features of HTTP v1.1.
•
•
HTTPS
FTP
The Master has a built-in SSL protected web server.
443 (TCP)
The on-board Master has a built-in FTP server that
conforms to RFC959.
21/20 (TCP)
•
•
•
•
Internet Inside The Internet Inside feature the Master uses, by default, is
port 10500 for the XML based communication protocol.
This port is connected to by the client web browser’s JVM
when Internet Inside control pages are retrieved from the
on-board Master’s web server.
10500 (TCP)
Input: Yellow LED lights when the Controller receives data from button
pushes, strings, commands, channel levels, etc.
ID Pushbutton: Sets the NetLinx ID (Device only) assignment for the
device.
|