Dell™ P1130 Color Monitor
Quick Setup Guide
Safety Instructions
Observe the following safety guidelines when connecting and using your monitor:
•
•
•
Be sure that your monitor is electrically rated to operate with the AC power available in your location.
Locate your monitor near an easily accessible electrical outlet.
Place the monitor on a solid surface and treat it carefully. The screen can be damaged if dropped, sharply hit, or touched
with a sharp or abrasive implement.
•
•
Put your monitor in a location with low humidity and a minimum of dust.
Never use your monitor if the power cable has been damaged. Do not allow anything to rest on the power cable, and
keep the cable away from where people could trip over it.
•
•
•
•
Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock.
To avoid electric shock, never touch the inside of the monitor. Only a qualified technician should open the monitor’s case.
Be sure to hold the plug, not the cable, when disconnecting the monitor from an electrical outlet.
Openings in the monitor cabinet are provided for ventilation. To prevent overheating, these openings should not be
blocked or covered. Also, avoid using the monitor on a bed, sofa, rug, or other soft surface. Doing so may block the
ventilation openings in the bottom of the cabinet. If you put the monitor in a bookcase or some other enclosed space,
be sure to provide adequate ventilation.
•
•
Do not expose the monitor to rain or use it near water. If the monitor accidentally gets wet, unplug it and contact an
authorized dealer immediately. You can clean the exterior of the monitor with a damp cloth when necessary, but be sure
to unplug the monitor first.
If your monitor does not operate normally-in particular, if there are any unusual sounds or smells coming from it-unplug
the monitor immediately and contact an authorized dealer or service center.
Quick Specifications
AC input voltage/frequency
Current
Operating Temperature
Dimensions
100 – 240 V ~ 50 – 60 Hz
1.6 A (RMS) at 120 VAC and 0.9 A (RMS) at 220 VAC
0° to 40°C (32° to 104°F)
502 mm × 497 mm × 485 mm (height × width × depth)
(19.8 × 19.6 × 19.1 inches)
Weight (monitor only)
30.5 kg (67 lbs 4 oz)
Other accessory items in the package
CD-ROM User’s Guide, AC Cord, video signal cable
Connecting Your Monitor to a Computer
2
1
AC IN
1
2
Turn off your computer(s) and unplug its power cable(s).
Connect your first computer to video input 1(HD15) using the supplied HD15 video signal cable. If you have a second
computer, connect it to video input 2 (HD15) using another HD15 video signal cable (not supplied).
Connect the other end(s) of the HD15 video signal cable(s) to the video output(s) of your computer(s).
Connect the power cable for your monitor to the power port on the back of the monitor.
Plug the power cables of your computer(s) and your monitor into a nearby outlet.
Turn on your monitor and computer(s). If the monitor does not display an image, refer to the troubleshooting section of
this guide.
3
4
5
6
Dell P1130 Color Monitor Quick Setup Guide
1
Microsoft® Windows® 2000 Operating System
To manually install or update the driver, perform the following steps:
1. Click Start--> Settings--> Control Panel and then double-click Display.
2. In the Display Properties window, click the Settings tab, and then click Advanced.
3. Click the Monitor tab, and then click Properties--> Driver--> Update Driver.
4. When the Update Device Driver Wizard dialog box appears, choose “Search for a suitable driver for my device,” and
click Next>.
5. Insert the monitor CD into the CD-ROM drive, type d:\ (change the drive letter to match your CD-ROM drive if it is not
drive D) in the Copy manufacturer’s files from: box, and click Next> and then Finish to complete the installation.
6. Close the Display Properties window.
Microsoft® Windows® 98 Operating System
Windows 98 automatically detects the new monitor and displays the Add New Hardware Wizard dialog box if the monitor
driver is not already installed.
1. Insert the monitor CD into the CD-ROM drive, and click Next> twice when the Add New Hardware Wizard dialog box
appears.
2. Click the CD-ROM drive box to install the drivers from the CD and then click Next>.
3. Confirm that the driver was found on the CD, and click Next> twice to install the driver.
4. Click Finish to exit the Add New Hardware Wizard dialog box.
To manually install or update the driver, perform the following steps:
1. Click Start--> Settings--> Control Panel and then double-click Display.
2. In the Display Properties window, click the Settings tab, and then click Advanced.
3. Click the Monitor tab, and then click Change.
4. When the Update Device Driver Wizard dialog box appears, follow the steps in the previous paragraph.
Setting Display Resolution
For optimal monitor performance while using Microsoft® Windows® XP, Windows® 2000, Windows® 98 or Windows NT®,
set the display resolution to 1280 × 1024 as follows:
1. Click Start--> Settings--> Control Panel.
2. Double-click the Display icon in the Control Panel window, and the click the Settings tab.
3. In the Desktop area, move the slidebar to 1280 × 1024 pixels. Then click OK.
Accessing the User’s Guide Online or via CD
To view the latest monitor User’s Guide, access the SUPPORT section of the Dell Web site (http://support.dell.com).
If you do not have Internet access, you can access the guide on the monitor CD:
1. Insert the monitor CD into your CD-ROM drive.
A start-up document should launch automatically; however, if the start-up document does not launch automatically,
click Start--> Run, type D:\monitor.htm, and click OK. (Substitute the correct CD-ROM drive letter if it is not the D
drive.)
2. Click the appropriate icon to open the User’s Guide in the desired language.
NOTE: All applicable warranty and regulatory information regarding your monitor is contained in the User’s Guide on your
CD.
Dell P1130 Color Monitor Quick Setup Guide
3
Troubleshooting Tips
Monitor Has No Power
If the monitor’s power indicator is off and no image appears on the display, perform the following checks:
•
•
•
•
Ensure that the power cable is fully inserted in the monitor’s power port and the electrical outlet.
Test the electrical outlet by plugging in a working electrical device such as a lamp.
Ensure that the power button has been depressed, and wait for the power indicator to light.
Try another power cable on the monitor. Use the computer’s power cable and turn on the monitor with the signal cable
disconnected. If the monitor is working correctly, a self-test pattern appears.
No Image Is Displayed on the Monitor
If the monitor power indicator is on but no image appears on the display, perform the following checks:
•
•
•
•
•
Ensure that the video connector is seated properly. Tighten the connector screws securely with your fingers.
Ensure that the computer is on.
Increase brightness and contrast controls.
Turn off the monitor and unplug the signal cable. Check the cable connector for bent or broken pins.
With the signal cable still disconnected, turn on the monitor. If the monitor is working correctly, a self-test pattern
appears.
•
Perform a monitor reset or recall.
IMPORTANT!
Before contacting Dell for technical assistance, refer to the Troubleshooting section in the User’s Guide on
your monitor CD. This section contains detailed information for resolving most monitor problems.
Information in this document is subject to change without notice.
© 2001 Dell Computer Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly
forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Computer Corporation; Microsoft and Windows
are registered trademarks of Microsoft Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and
names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other
than its own.
October 2001
4
Dell P1130 Color Monitor Quick Setup Guide
|