Mini P180 / Mini P180 White
User’s Manual
Manuel de l’utilisateur
Anwenderhandbuch
Manuale per l’operatore
Manual del usuario
পᡅ䂀ᯢ
Ё᭛Փ⫼
ݞ Installing the Motherboard
This manual does not cover CPU, RAM, or expansion card installation. Please consult
your motherboard manual for specific mounting instructions and troubleshooting.
1. Lay the case down, with the open side facing up. The drive cages and power
supply area should be visible.
2. Make sure you have the correct I/O panel for your motherboard. If the panel
provided with the case isn’t suitable, please contact your motherboard
manufacturer for the correct I/O panel.
3. Line up the motherboard with the standoff holes. Determine which holes line
up and remember where they are. Not all motherboards will match with all of
the provided screw holes, and this is not necessary for proper functionality.
Some standoffs may be pre-installed for your convenience.
4. Remove your motherboard by lifting it up.
5. Install standoffs as needed and put the motherboard back in.
6. Screw in your motherboard to the standoffs with the provided Philips-head
screws. Your motherboard is now installed.
Cable Organizer
Instead of running all the power cables into the upper chamber, they can be organized
between the motherboard and right side panel.
1. Remove both side panels.
2. Choose the cables you would like to pass through the holes behind
the motherboard tray and pull them out of the power supply chamber towards
the right side of the case.
3. Route them up through the gap in the bar and use the cable ties to hold them
in place.
4. Feed the cables back through the insertion point nearest the destination of
the cable. Connect the cable and then pull the slack back to the right side of
the case.
5. When finished, secure all cables with ties and put the right panel back in place.
Connecting the Ports and LEDs
1. Connect the Reset switch (labeled RESET SW) to your motherboard at the
RST connector. Polarity (positive and negative) does not matter for switches.
2. Power Switch (labeled POWER SW) connects to the PWR connector on
the motherboard.
3. Power LED (labeled POWER LED) connects to the PWR header on
the motherboard. For LEDs, colored wires are positive (+). White or black
wires are negative (–). If the LED does not light up when the system is powered
on, try reversing the connection. For more info on connecting LEDs to your
motherboard, see your motherboard manual.
4. Hard Drive LED (labeled HDD LED) connects to the hard drive activity header.
Connecting the USB Ports
You will find a single 10-pin connector on a cable attached to the front USB ports.
This Intel standard connector is keyed so that it can’t be accidentally reversed, as
long as it is connected to a proper Intel standard motherboard header. Connect the
10-pin connector to your motherboard headers so that the blocked pin fits over the
missing header pin.
2
Note: Please check your motherboard manual for your USB header pin layout and
make sure it matches the table below.
Motherboard Pin Layout
1
2
Pin
1
Signal Names
USB Power 1
Pin
2
Signal Names
USB Power 2
Negative Signal 2
Positive Signal 2
Ground 2
Negative Signal 1
Positive Signal 1
Ground 1
3
4
5
6
7
8
Key (No Connection)
Empty Pin
9
10
9 10
Connecting the eSATA Port
This case comes with an eSATA port in the front of the case to connect to your
external SATA devices. You will find a SATA connector on a cable attached to the
front eSATA ports. Connect it to a SATA connector on your motherboard.
Connecting the Audio Ports (AC’97 and HDA)
There is an Intel standard 10-pin AC’97 connector and an Intel 10-pin HDA (High
Definition Audio) connector, you can connect either of them to your motherboard
depending on the specification of the motherboard. See instruction below:
Pin Assignment for Audio Ports (HDA and AC’97)
Signal Names
(HDA)
Signal Names
(AC’97)
Pin
Pin
1
2
MIC2 L
AGND
1
2
MIC In
GND
3
MIC2 R
3
MIC Power
NC
10 6 4 2
9 7 5 3 1
4
AVCC
4
5
FRO-R
5
Line Out (R)
Line Out (R)
NC
6
MIC2_JD
F_IO_SEN
Key (no pin)
FRO-L
6
7
7
8
8
Key (no pin)
Line Out (L)
Line Out (L)
9
9
10
LINE2_JD
10
Note: Please check your motherboard manual for your audio header pin layout and
make sure it matches the table. Even if your system supports both audio standards,
you may only connect one connector, not both.
Installing the Drives
With the front bezel facing you, swing the front door out. It can swing 270
degrees so the door will be parallel with the side of the case. You can see one
5.25” external drive bay at the top and two 5.25” drive bays at the bottom of the
3
case. Inside the case there are two 3.5” drive cages located in the upper chamber,
which can house up to five hard drives.
Note: We recommend using the top 5.25” drive bay for your main 5.25” device.
5.25” Device Installation
There are three 5.25” drive bays that need a pair of drive rails for each drive. The
top 5.25” bay has a depth limitation of 170mm. Most new CD/DVD drives are not
longer than 170mm, but older bigger drives will have to be installed in one of the
lower two bays.
1. Carefully remove the plastic drive bay cover and the metal plate covering the
drive bay. There is a hole in the metal plate that will allow you to insert a
standard or Phillips screwdriver and rock the plate back and forth to break the
connector points.
2. Mount the drive rails onto the sides of the 5.25” device. Make sure the metal
portion is angled towards the outside of the case.
3. Slide the device into the drive bay until you hear a click.
4. Mount the other devices accordingly.
5. Hook up an appropriate connector from the power supply to the power connector
on each of the devices.
Upper HDD Installation
1. Remove the thumbscrew holding the upper HDD cage.
2. Pull the HDD cage from its position by pulling the ring towards you.
3. You can mount three hard drives inside the cage. They are mounted vertically
with the silicone grommets sitting at both sides.
4. Mount your hard drive into the drive cage with the special screws provided.
Don’t over-tighten the screws, as this will reduce the vibration and noise
dampening ability of the silicone grommets.
Note: Always mount the HDD with the thicker side of the silicone grommets
facing up.
5. Slide the cage back into the case and fasten the thumbscrew.
6. Find the right connector on the power supply and connect it to the hard drive.
7. Repeat the same procedure for the other drives.
Lower HDD Installation
1. Remove the thumbscrew holding the lower HDD cage.
2. Pull the HDD cage from its position by pulling the ring towards you.
3. There are two HDD trays inside the cage. Squeeze the metal clips on each
side of the tray and slide the tray out.
4. Mount your hard drive into the drive tray with the special screws provided.
Don’t over-tighten the screws as this will reduce the vibration and noise
dampening ability of the silicone grommets.
Note: Always mount the HDD with the thicker side of the silicone grommets
facing up.
5. Slide and lock the tray back into the cage.
6. Slide the cage back to the case and fasten the thumbscrew.
7. Find the right connector on the power supply and connect it to the hard drive.
8. Repeat the same procedure for the other drives.
4
Cooling System
The Rear 120mm TriCool™ fan:
This case comes with one 120mm TriCool rear fan installed. This fan has a three-speed
switch that lets you choose the speed that best suits your needs. The default
setting is Low. See the following specifications.
120mm TriCool Fan
Size:
120 x 120 x 25.4mm TriCool Fan
DC 12V
10.2V ~ 13.8V
Rated Voltage:
Operating Voltage:
Input
Current
Static
Air Flow
Input
Power
Acoustical
Noise
Speed
Pressure
High
2000 RPM
0.24A
(Max.)
2.24 m³ / min
(79 CFM)
2.54 mm-H2O
(0.10 inch-H2O)
30 dBA
28 dBA
25 dBA
2.9 W
2.4 W
1.6 W
Medium
1600 RPM
1.59 m³ / min
(56 CFM)
1.53 mm-H2O
(0.06 inch-H2O)
0.2A
Low
1200 RPM
1.1 m³ / min
(39 CFM)
0.92 mm-H2O
(0.04 inch-H2O)
0.13A
The Top 200mm TriCool™ Fan
The Mini P180 comes with a 200 x 30mm TriCool fan. This fan has a three-speed
switch that lets you choose the speed that best suits your needs. The default setting is
Low. See the specification below:
200mm TriCool Fan
Size:
200 x 200 x 30mm TriCool Fan
DC 12V
10.2V ~ 13.8V
Rated Voltage:
Operating Voltage:
Input
Current
Static
Air Flow
Input
Power
Acoustical
Noise
Speed
Pressure
High
800 RPM
0.3A
(Max.)
3.799 m³ / min
(134.11CFM)
0.688 mm-H2O
(0.027 inch-H2O)
29.4 dBA
3.6 W
Medium
600 RPM
3.07 m³ / min
0.397 mm-H2O
0.17A
0.08A
26.5 dBA
23.6 dBA
2.04 W
0.96 W
(108.493 CFM) (0.016 inch-H2O)
2.34 m³ / min 0.197mm-H2O
(82.612 CFM) (0.008 inch-H2O)
Low
400 RPM
The External fan Control:
There are two external fan switches on the rear of the case near the top. They allow
you to adjust the speed of these two fans without having to open the case.
Note: The minimum voltage to start these fans is 5V. We recommend our users to
set the fan speed to High if you choose to connect the fan to a fan control device
or to the Fan-Only connector found on some Antec power supplies. A fan-controller
regulates the fan speed by varying the voltage to it. The voltage may start as low
as 4.5V to 5V. Connecting a TriCool set on Medium or Low to a fan-control device
5
may result in the fan not being able to start. The already lowered voltage from the
fan controller will be further reduced by the TriCool circuitry below 5V.
We recommend setting these fans to Low speed to maximize quiet computing.
The Optional Fans
There are two optional 120mm fan mounts at the front of the case inside the HDD
cages. These two fan mounts are designed to enhance the CPU or VGA card cooling.
However, you will need to remove the HDD cage (as a result of sacrificing two or
three HDD bays depending on which cage to be removed) should you choose to
use the fan mount in it. In order to build a quieter system we recommend NOT
installing the optional fans.
The Washable Air Filters
There are two filters located behind the front grills and one filter inside the lower
chamber. From time to time it will be necessary to wash the installed air filters.
Not washing the air filters will result in higher system temperatures and possible
stability problems. We recommend checking the air filters at least once a month
initially. The frequency will depend on system usage (users whose systems run
24/7 will likely have to check/wash more often than those who don’t use their
systems every day) and on environmental conditions.
To remove the front filters:
1. Push one of the fan grills at the right middle edge to open the grill .
2. There are two tabs on the filter. To remove the filter use both your hands,
grip the tabs and slide it towards the center, tag it outwards and lift out.
To remove the bottom filter:
1. Grasp the locking tab and gently push it towards the center of the filter.
2. Tug the filter away from the case and then slide it out.
For more useful suggestions and advice on building this case please visit Antec’s
6
Antec, Inc.
47900 Fremont Blvd.
Fremont, CA 94538
USA
tel: 510-770-1200
fax: 510-770-1288
Antec Europe B.V.
Stuttgartstraat 12
3047 AS Rotterdam
The Netherlands
tel: +31 (0) 10 462-2060
fax: +31 (0) 10 437-1752
Customer Support:
US & Canada
1-800-22ANTEC
Europe
+31 (0) 10 462-2060
© Copyright 2008 Antec, Inc. All rights reserved.
All trademarks are the property of their respective owners.
Reproduction in whole or in part without written permission is prohibited.
Printed in China.
|