Preface
This manual is designed to assist users in setting up and using the LCD Monitor. Information
in this document has been carefully checked for accuracy; however, no guarantee is given to
the correctness of the contents. The information in this document is subject to change
without notice. This document contains proprietary information protected by copyright. All
rights are reserved. No part of this manual may be reproduced by any mechanical, electronic
or other means, in any form, without prior written permission of the manufacturer.
FCC Statement Warning
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy, and if not installed and used in accordance
with the instruction, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the manufacturers may void the
user's authority to operate this equipment.
NOTE
A shielded-type signal cord is required in order to meet the FCC emission limits and also to
prevent interference to the radio and television reception. It is essential that only the supplied
signal cord be used.
Canadian DOC Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
2
Cet appareil numérique de la classe B repecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Important Safety Instructions
Please read the following instructions carefully. This manual should be retained for future
use.
1. To clean LCD Monitor screen;
-- Power off LCD Monitor and unplug the AC Cord.
-- Spray a non-solvent cleaning solution onto a rag.
-- Gently clean the screen with dampened rag.
2. Do not place the LCD Monitor near a window. Exposing the monitor to rain water,
moisture or sunlight can severely damage it.
3. Do not apply pressure to the LCD screen. Excess pressure may cause permanent damage to
the display.
4. Do not remove the cover or attempt to service this unit by yourself. Servicing of any nature
should be performed by an authorized technician.
5. Store LCD Monitor in a room with a room temperature of -20° ~ 60°C (or -4° ~ 140°F).
Storing the LCD Monitor outside this range could result in permanent damage.
6. If any of the following occurs, immediately unplug your monitor and call an authorized
technician.
*
*
*
Monitor to PC signal cable is frayed or damaged.
Liquid spilled into LCD Monitor or the monitor has been exposed to rain.
LCD Monitor or the case is damaged.
7. A certified line is required to connect this device to a power outlet. For a nominal current
up to 6A and a device weight above 3 kg, a line not lighter than H05VV-F, 3G, 0.75 mm2
must be used.
8. For use only with power supply type: Li-shin, LSE 9802A1240
3
Chapter 1 Installation
Unpacking
Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and
computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD
Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very
little power, some ventilation is needed to ensure that the Monitor does not become too hot.
After you unpack the LCD Monitor, make sure that the following items were included in the
box:
*
*
*
LCD Monitor
*
*
*
AC Adapter
1.8M Power Cord
Base
1.5M Monitor-to-PC signal Cable
User's Manual
If you find that any of these items is missing or appears damaged, contact your dealer
immediately.
Connecting the LCD Monitor and Base
When you open the box to take the base
and put on the desk first. Then connect
the LCD Monitor and base please.(See
fig.1-1 )
Figure 1-1
View ing Angle Adjustment
The LCD Monitor is designed to allow
users to have a comfortable viewing
angle. The viewing angle can be
adjusted from -5°to +35°.(See fig. 1-2)
Figure 1-2
Warning
Do not force the LCD Monitor over its maximum viewing angle settings as stated above.
Attempting this will result in damaging the Monitor and Monitor stand.
4
Detaching LCD Monitor from Its Stand
1. Unscrew screws of the hinge bracket
2. Remove the stand from LCD monitor
(See fig. 1-3)
Figure 1-3
Interface for Arm Applications
Before installing to mounting device, please
refer to Fig.1-3.
The rear of this LCD display has four
integrated 4 mm, 0.7 pitches threaded nuts,
as well as four 5 mm access holes in the
plastic covering as illustrated in Figure 1-4.
These specifications meet the VESA Flat
Panel Monitor Physical Mounting
Interface Standard (paragraphs 2.1 and
2.1.3, version 1, dated 13 November 1997).
Figure 1-4
Connecting the Display to your Computer
1. Power off your computer.
2. Connect one end of the signal cable to the
LCD Monitor's VGA port. (See Fig. 1-5)
3. Connect the other end of the signal cable
to the VGA port on your PC.
4. Make sure both connections are secure.
Figure 1-5
Attention
This device must be connected to an off-the-shelf video cable in order to comply with FCC
regulations. A ferrite-core interface cable is included in the LCD Monitor package.
This device will not be in compliance with FCC regulations when a non-ferrite-core video
cable is used.
5
Connecting the AC Pow er
1. Connect the power cord to the AC adapter.
(See Fig. 1-6)
2. Connect the AC adapter's DC output
connector to the DC Power Jack of the
monitor.
3. Connect the power cord to an AC power
source.
Figure 1-6
Warning
We recommand to install a "Surge Protector" device between the AC Adapter and the
electrical wall outlet for adding protection against power surges to prevent the effects of
sudden voltage variations from reaching the LCD Monitor. Sudden power surges may
damage your monitor.
Setting Up the LCD Monitor
1. Make sure the AC Adapter is connected to the LCD Monitor.
2. Turn on the LCD Monitor's power switch, located on the bezel of the monitor.
Pow er Management System
This LCD Monitor complies with the VESA DPMS (version 1.0) Power Management guidelines.
The VESA DPMS provides four power saving modes through detecting a horizontal or vertical
sync. signal.
When the LCD Monitor is in power saving mode, the monitor screen will be blank and the
power LED indicator will light yellow.
6
Chapter 2 Display Controls
User Controls
A brief description and the location of all LCD Monitor function controls and indicators:
Figure 2-1
1
2
DC Pow er Sw itch
Press the power switch to switch the monitor ON/OFF.
LED lights Green color --- Power is ON.
LED lights Yellow --- Monitor is in "Power Saving Mode".
LED is off --- Power is OFF.
DC Pow er-On
Indicator
Function Select
Buttons
Press either left or right control button for OSD (On Screen
Display) menu selection.
3
4
Adjustment
Control Buttons
Press the left button to decrease the OSD setting and press
the right button to increase the OSD setting.
Adjusting the Monitor's Display
The monitor has four function control buttons to select among functions shown on
OSD menu, designed for easy user-viewing environments.
OSD Function Menu
To access OSD Main menu, simply press
one of the Function Select control
buttons, and the menu diagram will
pop up on the screen as shown on Fig.
2-2:
Continue pressing the Function Select
buttons to scroll through the entire
menu items ,then press Adjustment
Control buttons to adjust content of
selected item.
Figure 2-2
Attention
Firmware revision may have been updated into a latest version while the version number
shown on all OSD menus in this manual will stay as Ver. 1.00.
7
Function Description
Icon
Function
Function Description
Brightness
This function increases or decreases the brightness of the image.
This function increases or decreases the difference between the
dark and light color.
Contrast
H-Position
V-Position
This function shifts the entire display image left or right.
This function shifts the entire display image up or down.
A total of 32 scales (0 to 31) are available to adjust the focus and
clarity of the display.
This function carries a frequency tracking feature that offers the
user to have better stability and clarity. Increasing Clock value can
be up to +50 scales. The number of decreasing Clock (minus) is
depend on the input timing.
Phase
Clock
This function will adjust the display size automatically to fit full
screen.
Auto Adjustment
OSD H-Position
OSD V-Position
This function moves the OSD menu window left or right.
This function moves the OSD menu window up or down.
This function is to choose a display that allows maximum graphics
text quality. The resolution selection can either be 640 x 400 or
720 x 400. Please refer to Chapter 3 “ Standard Timing” Table for
of different timing modes.
The recall function will return all adjusted parameters to factory
preset values.
Graph Text
Recall
Five OSD language options are available:
English, German, French, Spanish and Italian.
Press the left or right Adjustment Control button to select other
language.
Language
Hue:100 scales of hue are available to adjust hue from green to
red.
Saturation:100 scales of saturation are available to choose from 0
to 100. Color Temp.: Push the (+ -) button to select a different
color temperature. Please see the diagram below for function and
description.
Color
managemen
t
Save Exit
Saves the values of this setting and exits the OSD menu function.
Icon
Function
Description
CIE coordinated Color Temperature of
9300°K
Sets the CIE coordinate color
temperature to 9300°K
9300
6500
CIE coordinated Color Temperature of
6500°K
Sets the CIE coordinate color
temperature to 6500°K
8
Three colors (Red, Green, Blue) can be
adjusted from the OSD menu
Sets the settings to a by user defined
CIE Temperature.
User
9
Chapter 3 Technical Information
Specifications
LCD Panel
Size
Hannstar
15.0" (38 cm)
AU
15.0" (38 cm)
Display Type
Resolution
Active matrix color TFT LCD Active matrix color TFT LCD
1024 x 768
1024 x 768
Display Dot
1024 x (RGB) x 768
304 x 228 (H x V)
262K
1024 x (RGB) x 768
304 x 228 (H x V)
262K
Display Area (mm)
Display Color
Brightness
200 cd/m2 (typical)
200 cd/m2 (typical)
Contrast Ratio
Response Time
Lamp Voltage
Lamp Current
Viewing Angle
300: 1 (typical)
350: 1 (typical)
(15 + 35) ms (typical)
640 Vrms (typical)
6.0 mA rms. (typical)
Vertical: -45° ~ +40°
Horizontal: -60° ~ +60°
30 ms (Tr+Tf) (typical)
630 Vrms (typical)
6.5 mA rms. (typical)
Vertical: -60° ~ +40°
Horizontal: -60° ~ +60°
Display Colors
Video
16.7M with FRC or Dithering
Input Signal
Input Impedance
Polarity
Analog RGB 0.7Vp-p
75 Ohm ± 2%
Positive
Amplitude
0 - 0.7 ± 0.05 Vp
Multi-mode Supported
Horizontal Frequency: 24 ~ 61 KHz
Vertical Frequency: 56 ~ 75 Hz
Control
Power
On/Off switch with LED indicator
OSD
Brightness
Digital
Contrast
Digital
Horizontal Position
Vertical Position
Phase
Digital
Digital
Digital
Clock
Digital
Display Mode Setup
OSD Format
Use EEPROM to save settings in memory
20 characters x 9 rows
10
Pow er Management
Pow er
Mode
AC Input
LED Color
Consumption*
25W maximum
5W maximum
5W maximum
5W maximum
5W maximum
On
Standby
Suspend
Off
240 VAC
240 VAC
240 VAC
240 VAC
240 VAC
Green
Yellow
Yellow
Yellow
Dark
DC Power Off
Yellow: Standby, Suspend,
Off
Disconnected
5W maximum
240 VAC
Dark: DC Power off
* Meeting VESA DPMS requirements measured from AC Input end of AC adapter.
Sync Input
Separate TTL compatible horizontal and vertical
synchronization
Signal
Polarity
Positive and negative
Plug & Play
External Connection
Supports VESA DDC1 and DDC2B functions
Power Input (DC input)
Video Cable
+12 VDC / 2.5A min. input through AC/DC adapter
1.5M with 15-pin D-sub connector
Environment
Operating Condition:
Temperature
5°C to 40°C/41°F to 104°F
20% to 80%
Relative Humidity
Storage Condition:
Temperature
-20°C to 60° C/-4°F to140° F
5% to 85%
Relative Humidity
Pow er Supply (AC Adapter)
Input Voltage
Input Current
Single phase, 100 ~ 240VAC, 50 / 60 Hz
1.5 A maximum
Size and Weight
Dimensions
Net Weight
Gross Weight
349.6 (W) x 371.5 (H) x 158 (D) mm
3.2 ± 0.3 kg
4.7 ± 0.3 kg
11
Pin Assignment
6
Signal
Signal
Description
PIN
Description
PIN
1
2
3
4
5
6
7
8
Red
9
+5V
11
1
5
Green
10
11
12
13
14
15
NC
Blue
Digital GND
SDA
Digital GND
Digital GND
Red Rtn
Green Rtn
Blue Rtn
15
10
H. Sync.
V. Sync.
SCL
Standard Timing Table
If the selected timing is NOT included in table below, this LCD monitor will use the most
suitable available timing.
V. Freq.
(Hz)
H. Freq.
(KHz)
Pixel Freq.
(MHz)
H/V Sync.
Polarity
Resolution
Mode
VGA-350
640 x 350
640 x 400
31.469
24.830
70.087
56.420
25.175
21.050
+/-
-/-
NEC PC9801
VGA-400-GRAPH
NEC PC9821
640 x 400
31.469
70.087
25.175
-/+,-/-
VGA-480
640 x 480
640 x 480
640 x 480
720 x 400
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024x 768
1024x 768
1024x 768
1024x 768
31.469
37.861
37.500
31.469
35.156
37.879
48.077
46.875
49.725
48.363
53.964
56.476
60.023
59.940
72.809
75.000
70.087
56.250
60.317
72.188
75.000
74.55
25.175
31.500
31.500
28.322
36.000
40.000
50.000
49.500
57.2832
65.000
71.664
75.000
78.750
-/-
-/-
VESA - 480 - 72Hz
VESA - 480 - 75Hz
VESA-400-TEXT
SVGA
-/-
-/+
+/+
+/+
+/+
+/+
-/-
VESA-600-60 Hz
VESA-600-72 Hz
VESA-600-75 Hz
APPLE MAC-800
XGA
60.004
66.132
70.069
75.029
-/-
COMPAQ-XGA
VESA-768-70 Hz
VESA-768-75 Hz
+/+
-/-
+/+
12
Troubleshooting
This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the output
timing differences among various VGA cards in the market, users may initially experience an
unstable or unclear display whenever a new display mode or new VGA card is selected.
Attention
This LCD Monitor Supports Multiple VGA Modes.
Refer to the Standard Timing Table for a listing of modes supported by this LCD Monitor.
PROBLEM
Picture is unclear and unstable
The picture is unclear and unstable, please perform the following steps :
1. Enter PC to “Shut Down Windows” status while you’re in MS-Windows environment.
2. Check the screen to see if there’s any black vertical stripes appear. If there are, take
advantage of the “Clock” function in OSD menu and adjust (by increment or decrement
numbers) until those bars disappear.
3. Move to “Phase” function in OSD menu again and adjust the monitor screen to its most
clear display.
4. Click “No” on “Shut Down Windows” and back to the normal PC operating environment.
PROBLEM There is no picture on LCD Monitor
If there’s no picture on the LCD Monitor, please perform the following steps:
1. Make sure the power indicator on the LCD Monitor is ON, all connections are secured,
and the system is running on the correct timing. Refer to Chapter 3 for information on
timing.
2. Turn off the LCD Monitor and then turn it back on again. If there is still no picture, press
the Adjustment Control button several times.
3. If step 2 doesn’t work, connect your PC system to another external CRT. If your PC
system Functions properly with a CRT Monitor but it does not function with the LCD
Monitor, the output timing of the VGA card may be out of the LCD’s synchronous range.
Please change to an alternative mode listed in the Standard Timing Table or replace the
VGA card, and then repeat steps 1 and 2.
PROBLEM
There is no picture on LCD Monitor
If you have chosen an output timing that is outside of the LCD Monitor’s synchronous range
(Horizontal: 24 ~ 61 KHz and Vertical: 56 ~ 75 Hz), the OSD will display a “Out of Range”
message. Choose a mode that is supported by your LCD Monitor.
Also, if the signal cable is not connected to LCD monitor at all or properly, the monitor
screen will display a message “No Input Signal”.
13
|