User Guide
Keys
Fixed-length
antenna
Power key
Do not
attempt to
extend or
remove!
Earpiece
Current
function of
Navi™ key
Screen
Navi™ key
Menu
Scroll keys
Clear key
Number keys
Voice mail key
Emergency 9 key
Indicators and icons
You have an active call.
You have one or more new voice messages.
You have one or more new text messages.
Keyguard is on. Your phone will not accept any
keypresses. To turn it off, press Unlock, then
.
The alarm clock is set.
The ringing option is set to Silent.
Digital service is available.
The phone is ready for you to enter a response.
You are in predictive text mode.
Characters entered will be upper-case letters.
Press the
key to switch letter case.
Characters entered will be lower-case letters.
Press the key to switch letter case.
Characters entered will be numbers. (When entering
letters, switch to numbers by pressing and holding
the
key.)
You are in “special character” mode; select a
character, then press Use. (When entering letters,
switch to special characters by pressing the
key.)
Table of contents
i
Adding feature activation codes
Adding feature cancellation codes
to the menu . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Choosing your phone number
(NAM selection). . . . . . . . . . . . . . . . . . . . . . . . . .33
ii
iii
19. Index
83
iv
1. For your safety
Read these simple guidelines before using your phone.
Failure to comply with these guidelines may be dangerous
or illegal.
Road Safety Comes First
Don’t use a hand-held phone while driving; park the
vehicle first.
Switch Off In Hospitals
Follow any regulations or rules. Switch phone off near
medical equipment.
Switch Off On Aircraft
Wireless phones can cause interference. Using them on
aircraft is illegal.
Switch Off When Refueling
Don’t use phone at a refueling point. Don’t use near fuel or
chemicals.
Switch Off Near Blasting
Do not use the phone where blasting is in progress.
Observe restrictions, and follow any regulations or rules.
Interference
All wireless phones may get interference which could
affect performance.
Use Sensibly
Use only in the normal position (to ear). Don’t touch the
antenna unnecessarily.
Qualified Service
Only qualified service personnel must install or repair
equipment.
Accessories and Batteries
Use only approved accessories and batteries. Do not
connect incompatible products.
1
FCC/Industry Canada Notice
Your phone may cause TV or radio interference (for example,
when using a telephone in close proximity to receiving
equipment). The FCC or Industry Canada can require you
to stop using your telephone if such interference cannot
be eliminated. If you require assistance, contact your local
service facility.
This device complies with part 15 of the FCC rules. Operation is
subject to the condition that this device does not cause
harmful interference.
Using this Guide
The wireless phone described in this guide is approved for
use in TDMA and AMPS networks.
Network services
A number of features included in this guide are called
network services. They are special services provided by
wireless service providers. Before you can take advantage
of any of these network services, you must subscribe to
the service(s) from your home service provider and obtain
instructions for their use.
Updates
The latest version of this User Guide may be found on
Interactive manual
Now, Nokia has a great new way for you to learn how to use
access the Nokia Interactive User Guide. It provides an
interactive way to get step-by-step instructions for any of
your phone's features.
2
2. Battery installation and charging
Before you can use your new phone, you need to attach and
charge the battery.
Attaching the battery
To attach the battery, place it
on the back of the phone as
shown and slide it toward the
top of the phone until it clicks
into place.
Battery charging
Your phone is powered by a rechargeable NiMH or Li-Ion
battery. Note that a new NiMH battery’s full performance
is achieved only after two or three complete charge and
discharge cycles. For charging times, see ‘Charging times’ on
How to charge your battery
Connect the lead from the charger to the bottom of your
phone or to a charging stand. Then plug the charger into a
standard wall outlet.
When the battery is charging, the battery strength indicator
on the right side of the display scrolls.
Note: When you charge the battery for the first time, the
battery strength indicator will not scroll the entire time; this
is normal.
Problems charging
If your phone displays Not charging, charging is suspended.
Check that the battery is connected to an approved charging
device. If the battery is very hot or cold, wait for a while;
charging will automatically resume after the battery is
3
restored to its normal operating state. If charging still fails,
contact your dealer.
When is charging complete?
When the charge indicators stop scrolling, your
phone is considered fully charged. However, a
slight increase in charge may occur if you leave
your phone connected to the charger.
When is a good time to charge?
You can charge anytime, but remember that when your
phone displays Battery low, you only have a couple of
minutes of talk time left.
Can I make calls while charging?
Yes, but depending on the charger used, your battery may
not charge during a call.
Discharging NiMH batteries
For good operation times, discharge NiMH batteries from
time to time by leaving your phone switched on until it
turns itself off (or by using the battery discharge facility of
any approved accessory available for your phone). Do not
attempt to discharge the battery by any other means.
Removing the battery
Note: Switch off the phone before removing the battery!
1
2
3
Press and hold the
button at the top of the
battery.
Slide the battery
toward the bottom of
the phone.
Lift the battery off the
phone.
4
Important battery information
•
Note that a new battery’s full performance is achieved only after
two or three complete charge and discharge cycles!
•
The battery can be charged and discharged hundreds of times
but it will eventually wear out. When the operating time (talk
time and standby time) is noticeably shorter than normal, it is
time to buy a new battery.
•
•
Use only batteries approved by the phone manufacturer and
recharge your battery only with the chargers approved by the
manufacturer.
When a charger is not in use, disconnect it from the power source.
Do not leave the battery connected to a charger for longer than
a week, since overcharging may shorten its life. If left unused a
fully charged battery will discharge itself over time.
•
(NiMH batteries only) For good operation times, discharge the
battery from time to time by leaving your phone switched on
until it turns itself off (or by using the battery discharge facility
of any approved accessory available for your phone). Do not
attempt to discharge the battery by any other means.
•
Temperature extremes will affect the ability of your battery to
charge: allow it to cool down or warm up first.
•
•
•
Use the battery only for its intended purpose.
Never use any charger or battery which is damaged or worn out.
Do not short circuit the battery. Accidental short circuiting can
occur when a metallic object (coin, clip, or pen) causes direct
connection of the + and - terminals of the battery (metal strips
on the back of the battery), for example when you carry a spare
battery in your pocket or purse. Short circuiting the terminals
may damage the battery or the connecting object.
•
Leaving the battery in hot or cold places, such as in a closed car
in summer or winter conditions, will reduce the capacity and
lifetime of the battery. Always try to keep the battery between
59º F and 77º F (15º C and 25º C). A phone with a hot or cold
battery may temporarily not work, even when the battery is fully
charged. NiMH batteries’ performance is particularly limited in
temperatures below 14º F (-10º C). Li-Ion batteries’ performance
is particularly limited in temperatures below 32º F (0º C).
•
•
Do not dispose of batteries in a fire!
Dispose of used batteries in accordance with any local regulations.
5
3. About the phone, keys and menu
Power key
You can use the power key
to:
•
•
•
turn the phone on or off (press and hold)
turn the phone’s lights on for 15 seconds
is off and the phone is not connected to a headset or
handsfree car kit)
•
silence the ringing of an incoming call
Nokia Navi™ key
Your phone’s Navi™ key
appears
below the display. Its current function
is indicated by the word that appears
above it (for example, Menu). Simply
press the Navi™ key to perform the
function.
Throughout this guide, when you see “press Menu,” “press
Listen,” etc., press the Navi™ key when that word appears
above it.
Scroll keys
The scroll keys
are located to the right of the
Navi™ key. Use the scroll keys to:
•
•
•
•
•
browse menus
adjust the earpiece volume while in a call
access your phone book (press
from the start screen)
from the start
access the dialed calls list (press
screen)
6
Clear key
Use the clear key
to:
•
•
•
•
•
delete a character to the left of the cursor
clear all characters from the display (press and hold)
return to the previous menu level
return from the menu to the start screen (press and hold)
access the in-call menu while in a call
Lights
To turn your phone’s lights on for 15 seconds:
•
•
if Keyguard is off, press any key
if Keyguard is on, you must press the
key briefly
(this conserves battery power by keeping the lights
from turning on when the phone is in a pocket or purse)
For information about controlling your phone’s lights when
External antenna jack
At the back of the phone, below the antenna, there is a
connector for an external antenna. The connector may be
protected by a rubber cap. Remove the cap before connecting
an external antenna. After removing the antenna, replace
the cap.
Note: Keep the cap out of the reach of small children.
Start screen
The start screen appears when you first
turn on your phone. Menu appears
above the Navi™ key so you can access
your phone’s menu. Several features
can be used only when the phone is at
the start screen.
To get to the start screen, press and hold
for a second.
(If there are characters on the display this clears the
characters, then you must press and hold
again.)
7
Menu
Your phone’s menu allows you to easily access the many
powerful features in your phone.
Scroll bar
When you use your phone’s menu, a scroll bar
appears at the far right of the screen. This bar
indicates where you are in the menu; each tab
location on the bar represents a different menu
item.
For example, press Menu once. The scroll bar appears with
the first (top) tab displayed. A different tab appears each
time you press one of the scroll keys
.
Help text
Many menu items have brief help text. To view the help text,
scroll to the menu item and wait for about 10 seconds for
the text to appear. Press More or
to see the next page
of text,
to see the previous page, or to return to
the menu.
8
Menu shortcuts
When you select a menu item, numbers appear on
the display above the scroll bar. If you become
familiar with these numbers, you can use them as
shortcuts for accessing different menu items. For
example, to access the Phone settings menu, you
can simply press Menu 4 2. The phone displays the first item
in that menu, Touch tones.
Note: (1) Menu items in your phone vary depending on the
network and accessories used. (2) This is not a complete list;
see entries about individual features for more information.
1 Phone book
11 Search
12 Add new
13 Edit
3 Call log
31 Missed calls
32 Received calls
33 Dialed calls
34 Clear call lists
14 Erase
141 One by one
142 Erase all
341 All
342 Missed
343 Received
344 Dialed
15 Options
151 Scrolling view
152 Memory status
35 Call timers
351 Last call
352 All calls
353 Life timer
354 Clear timers
16 1-touch dialing
17 Send bus. card
2 Messages
21 Text messages
211 Inbox
212 Saved
213 Write message
214 Write e-mail
215 Outbox
216 Erase all
22 Voice messages
221 Listen to voice
messages
222 Voice mailbox number
23 Welcome note
9
4 Settings
8 My tones
41 Call settings
81 Ringing options
411 Emergency key 9
811 Ring
412 Automatic redial
413 Calling card
812 Ascending
813 Ring once
814 Beep once
815 Silent
414 Automatic answerh
42 Phone settings
82 Ringing tone
83 Ringing volume
421 Touch tones
422 Language
423 Restore factory settings
831 Level 1
832 Level 2
833 Level 3
834 Level 4
835 Level 5
424 Lightsc
43 Security settings
431 Restrict calls
432 Access codes
44 Network services
84 Message alert tone
441 Voice privacy
841 No tone
842 Standard
843 Special
844 Beep once
845 Long & loud
442 Network feature setting
443 Call forwardingm
444 Call waitingm
445 Send own numberm
45 Own number selection
85 Keypad tones
851 Off
5 System
51 Automatic
52 Manual
852 Level 1
853 Level 2
854 Level 3
86 Warning and game
53 New search
tones
861 On
862 Off
6 Games
61 Memory
62 Snake
63 Logic
87 Vibrating alertv
871 On
872 Off
7 Clock
71 Alarm clock
72 Clock settings
9 Keyguard
Prepaidp
721 Display/Hide clock
722 Adjust time
723 Time format
1
2
3
Check account
balance
Add money to
account
Save access phone
numbers
73 Auto update of time
731 On
732 Confirm first
733 Off
c
Visible only when used with car kit
h
Visible only when used with headset or car kit
Must be added to the menu manually; see ‘Network feature setting’ on page 29
Visible only when vibrating battery is attached
m
v
p
Visible only when Prepaid menu activated
10
Entering letters and numbers
Cursor
The cursor is a blinking vertical line that appears on the screen
when you are entering text or numbers. Characters you
enter appear to the right of the cursor. Pressing the
key deletes the character to the left of the cursor. Use the
scroll keys to move the cursor to the right
or left
.
ABC mode
When your phone is ready for you to enter text, such as a
name or message, it switches to ABC mode. The
shows that it is in ABC mode.
icon
When
is displayed, you can enter these characters by
pressing the indicated key repeatedly:
Key
1
Characters
. , ‘ ? ! @ - 1
ABC2
Key
7
Characters
PQRS7
2
8
TUV8
3
DEF3
9
WXYZ9
space, 0
4
GHI4
5
JKL5
6
MNO6
Changes letter case,
switches between
letters and numbers
Changing letter case
Press the
case letters. The
key to switch between upper- and lower-
icon switches to to indicate
that you are using lower case.
11
There is an extra feature in your phone called Predictive text
input. For more information on this special text writing feature,
see page 57.
Entering numbers
To enter numbers while in ABC mode, you can:
•
press and hold the corresponding key until the number
appears, or
•
switch between ABC mode and number mode by
pressing and holding the
key.
Special characters in names
In ABC mode you can press the
key to view the special
characters below. You can use these characters when saving
names in your phone book. Simply press or to
highlight the one you want, then press Use. The scroll keys
move the cursor forward and backward, while pressing
moves the cursor down.
. , @ ? ! : ; - + # * ( ) ‘ “ _ & $ % / < > =
Tip: To choose a character that appears near the end
of the list, immediately press
to go to the end of
the list.
Special characters in phone numbers
You can use special characters to dial or save phone numbers
of automated services such as bank account information.
When entering numbers, press the
you see the character you want.
key repeatedly until
Character
Use
*
This character is used to request services
from the network. Contact your service
provider for details.
+
This character is not currently used.
12
Character
p
Use
This character creates a pause. Digits to the
right of the p are sent as touch tones after a
2.5-second pause.
Use this character to save phone numbers of
automated services that require you to enter
a password or other information after the
call is answered. For example, if your voice
mail number at work is 555-1212 and you
need to enter your extension (1234) and then
a password (5678) in order to listen to your
messages, you could save this phone number
as 5551212p1234p5678.
w
This character creates a wait. It works similarly
to the pause character except that digits to
the right of the w are not sent until you press
Send.
Keyguard (locking the keypad)
The Keyguard feature allows you to
lock your phone’s keypad so that
accidental keypresses have no effect.
This is handy when your phone is in a
pocket or purse.
Note: Keyguard is not a security feature and will not prevent
unauthorized use of your phone.
To lock the keys
Press Menu 9 or Menu
.
To unlock the keys
Press Unlock
.
13
Notes about Keyguard
•
When Keyguard is on, the only way to answer a call is to
press Answer.
•
When Keyguard is on, calls may be possible to the emer-
gency number programmed into your phone (e.g. 911 or
other official emergency number). However, one-touch
emergency dialing (‘emergency key 9’) does not operate.
•
•
Keyguard is automatically turned off when the phone is
connected to a car kit.
Keyguard menu is replaced by Prepaid menu when
Prepaid is activated. Keyguard function is available.
14
4. Basic functions
Turning the phone on or off
Press and hold the
key for one second.
WARNING! Do not switch on the phone when wireless phone
use is prohibited or when it may cause interference or danger.
About the antenna
Your Nokia phone has a fixed-length antenna. Do not attempt
to extend or remove it.
Normal position
Hold the phone as you would any other telephone, with the
antenna pointed up and over your shoulder.
Tips on efficient operation
As with any other radio transmitting device, do not touch the
antenna unnecessarily when the phone is switched on. Contact
with the antenna affects call quality and may cause the phone
to operate at a higher power level than otherwise needed.
Checking signal strength
Your phone operates on radio waves. Radio signal coverage is
maintained by a wireless network, and the quality of calls on
your phone depends on the strength of the wireless radio signal.
Get a strong signal
a call, the strength of the radio signal is indicated
by the signal indicators on the left side of your
phone’s display. These indicators scroll as the
signal strength increases and decreases.
15
To improve your phone’s reception, try moving your phone
slightly. If you’re inside a building, move toward a window.
Making a call
1
Enter the area code and phone
number. (Menu changes to Call.)
2
Press Call and wait for the other
party to answer.
Volume adjustment (earpiece)
To adjust the earpiece volume, press
or
during a
call. If an accessory with its own loudspeaker is connected
to your phone, the scroll keys will adjust the volume for that
accessory.
Muting the microphone
When you are in a call, you can mute the phone’s microphone
by pressing
, pressing Options, and selecting Mute.
To unmute the microphone, press
, press Options, and
select Unmute.
Note: For more information about the in-call menu,
Ending a call
Press End.
Last number redial
The last 10 numbers you dialed are stored in the dialed calls
list. Use this list to redial a number you have called recently.
1
From the start screen, press
calls list.
to access the dialed
2
3
Scroll to the desired number.
Press Call.
16
Saving a name and number
Finding a name and number
1
2
Press
to access your phone book.
Scroll to the number you want. (To skip ahead quickly in
the list, press the number key that corresponds to the
first letter of the name.)
3
Press Call.
For other ways to find names and numbers, see ‘Finding
Answering a call
When someone calls, the phone will alert you (see ‘Tones’ on
call, press any key except
.
Note: To prevent accidental answering when the phone is in
a pocket or purse, the phone will not answer the call if you
press the key for longer than one second.
For information on setting your phone to answer incoming
Caller ID
Caller ID is a network service that can display the name and
phone number of the person calling you, if the information
is available. Contact your service provider for details.
If the caller can be identified, the
phone may display the caller's name
and phone number. The information
displayed depends on the information
available through the network and
your phone book. It is possible that only the name or the
number will appear.
17
5. Settings
This section describes some phone settings that allow you to
customize your phone to suit your preferences and that you
probably won’t change very often.
Automatic redial
Use Menu 4 1 2 to turn this feature on or off. When this
feature is on and the wireless network is busy, your phone
will redial a number up to three times. This feature will not
redial to a busy phone number.
To stop the call attempts, press Quit or
.
Calling card set-up
If you wish to use a calling card for
long distance calls, you must first save
your calling card information into your
phone. Your phone can save information
about two calling cards.
To learn how to make calling card calls, see ‘Calling card
For more information on Prepaid services, see page 59.
Saving calling card information
1
2
3
4
5
Press Menu 4 1 3.
Scroll to the desired calling card, then press Options.
Scroll to Edit, then press OK.
At Dialing sequence, press Select. Press
to choose
the dialing sequence your card uses, then press Select.
19
Dialing
sequence
Use for cards that
require you to:
Cards using
this sequence
Access no. Dial 1-800 access number, MCI, AT&T True
+ phone no. then phone number, then Choice, Sprint
+ card no. card number (+ PIN if
required)
Canada, Unitel
Access no. Dial 1-800 access number, networkMCI,
+ card no. then card number (+ PIN if WorldPhone
+ phone no. required), then phone
number
MCI
Prefix
Dial the prefix (any numbers GTE, PacBell,
+ phone no. that must precede the
+ card no. phone number) and phone
number you want to dial,
then card number (+ PIN if
required)
AT&T, Stentor
Note: The order of the following steps may vary, depending
on which dialing sequence your card uses.
6
7
8
Enter access number (usually the 1-800 number listed
on the back of the calling card), then press OK.
Enter your card number and/or PIN, then press OK. Your
phone will display Save changes? Press OK.
Press
to reach Card name, then press Select. Enter
the card name using your phone’s keypad, then press OK.
Note: This procedure might not work with all calling cards.
Please look at the back of your calling card or contact your
long distance company for more information.
Choosing a calling card to use
To select a calling card to use, press Menu 4 1 3, scroll to the
card you want, then press Options. Select is highlighted;
press OK. Enter your security code, then press OK.
20
Clock
Your phone has an internal clock that
can be displayed on the start screen.
The clock must be set in order for call
times to be recorded (see ‘Call log’ on
If you remove the battery for longer than a couple of seconds,
the time will be lost. The next time you turn on the phone,
you will be asked to enter the time.
For more information on automatic time update of the clock
Selecting time format
Use Menu 7 2 3 to set the clock’s format to 24-hour or
am/pm.
Setting the time
Use Menu 7 2 2 to enter the current time. Use two digits for
both hours and minutes (for example, enter 1:30 as 0130).
If the clock’s time format is set to am/pm, you will be asked
to choose am or pm.
Note: The
key does not work on this screen. If you make
a mistake, re-enter all four digits.
Displaying or hiding the clock
Press Menu 7 2 1 to display the clock on the phone’s screen
if it is currently hidden, or vice versa.
When the clock is displayed and the
3:15 a.m.
3:15 p.m.
03:15
03:15
time format is set to am/pm, a black
square will appear next to the time
indicating a.m. or p.m.
Language
Use Menu 4 2 2 to set the language of
your phone’s display. You can choose
from English, French, Spanish, and
Portuguese.
The shortcut for choosing English is to
press Menu 4 2 2 1.
21
Lights
If you’re using your phone with a car kit, use Menu 4 2 4 to
set your phone’s lights to On (lights stay on) or Automatic
(after 15 seconds, lights turn off until the next key is pressed,
phone rings, etc.).
For information about turning your phone’s lights on at any
time, see page 7.
Time update from the network
This feature updates your phone’s built-in clock from the
network. The phone can update its internal time if the time
on your phone is 2 minutes off or more the network time.
The feature is network dependent. Contact your service
provider for details.
Turning on automatic time update
When you turn on the automatic time update, the phone
automatically updates the time from the network when you
turn the phone on.
Note: You need display the clock on the phone’s screen before
•
Press Menu 7 3 1 to turn on the automatic time update.
Turning on confirm first with time update
When you turn on confirm first with the time update, your
phone asks for a confirmation before it updates the internal
time from the network. You can choose to accept or decline
the update.
Note: You need display the clock on the phone’s screen before
•
Press Menu 7 3 2 to turn on confirm first with time
update.
Turning off the time update
When you turn off the time update, the phone does not update
its internal time from the network. Instead, the phone uses the
time you have set. You need to set the time manually.
22
•
•
Press Menu 7 3 3 to turn off the time update.
Press Menu 7 2 2 to set the time on your phone.
Tones
Use Menu 8, My tones, to change the six sound settings in your
phone: ringing option, ringing tone, ringing volume, message
alert tone, keypad tones, and warning and game tones.
select a fixed combination of these settings to suit your
current environment.
Ringing option
Use Menu 8 1 to tell your phone how to notify you that you
have a call.
Note: If you choose Beep once or Silent, the alarm clock
will only sound a quiet beep.
Ring The phone rings normally using the currently selected
ringing tone.
Ascending The phone rings using the currently selected
ringing tone. The ringing volume starts low and increases
with successive rings.
Ring once The phone rings once using the currently
selected ringing tone.
Beep once The phone beeps once.
Silent The phone makes no sound when you receive a call.
The
icon appears at the start screen.
Ringing tone
Your phone plays a ringing tone when someone calls you
and the ringing option is set to Ring, Ascending, or Ring
once. Use Menu 8 2 to choose one of 30 ringing tones.
Scroll to a tone to hear how it sounds.
Note: If the ringing option is set to Silent or Beep once, the
phone won’t play sample tones.
For more information on downloading ringing tones, see
23
Ringing volume
Use Menu 8 3 to control the volume of
your phone’s ringing and of message
alert tones.
Note: If your phone does not ring
loudly enough at maximum volume, try
a different ringing tone; some tones are louder than others.
Message alert tone
Use Menu 8 4 to choose the tone played when you receive a
text message. Scroll to a tone to hear how it sounds.
Keypad tones
Use Menu 8 5 to adjust the volume of the tones your phone
makes when you press its keys.
Warning and game tones
Use Menu 8 6 to turn your phone’s warning and game tones
on or off. Warning tones are created by events such as
confirmations, errors, power on, battery low, and recharge
battery.
Vibrating alert
If your phone has a vibrating battery attached, use Menu 8
7 to set your phone to vibrate when you receive a voice call.
If you turn vibrating alert on, your phone will vibrate even if
its ringing option is set to Silent.
Note: The vibrating battery does not vibrate when your
phone is connected to or placed in any charging device.
Quick alert settings
You can quickly adjust your phone’s
sound settings when you go into a
meeting, go outdoors, etc. To choose a
quick alert setting, briefly press the
key, scroll to the setting you want,
then press OK.
24
Tip: Instead of using the scroll keys, you can press
the key repeatedly to scroll through this menu.
After you reach the setting you want, press and hold
the key.
Note: If you choose Silent or Quiet, the alarm clock will
only sound a quiet beep.
My tones Uses the settings you have made in Menu 8,
My tones.
Silent All sound is turned off.
Quiet Your phone beeps once when you receive a call or
text message. Other tones are turned off.
Loud Your phone rings loudly. Other tones are not affected.
Headset Automatically selected when your phone is
connected to a headset. Remembers any changes you make
to settings in Menu 8, My tones, and uses them the next
time you connect the phone to a headset.
Car Automatically selected when your phone is connected
to a car kit. Remembers any changes you make to settings in
Menu 8, My tones, and uses them the next time you connect
the phone to a car kit.
Note: If the Silent, Quiet, or Loud quick alert setting is
chosen and you change a setting in Menu 8, My tones, the
phone switches the current quick alert setting to My tones.
Voice mailbox number
If you have a voice mail subscription, use Menu 2 2 2 to save
the voice mailbox number given to you by your service provider.
This number may be up to 32 digits long. Once you save your
voice mailbox number, you can press and hold the
to dial your voice mailbox. (You can also press
and then press Call.)
key
briefly
For more information on voice mail, see page 44.
25
Voice privacy
Available only in digital networks, voice privacy encrypts the
voice channel so it is more difficult for anyone to eavesdrop
on your conversations. Use Menu 4 4 1 to turn voice privacy
on or off.
This feature may not be available in all areas; contact your
service provider for details. If voice privacy becomes inactive,
the phone beeps and displays Voice privacy not active.
Welcome note
Use Menu 2 3 to create or change the
welcome note for your phone. This
note is displayed briefly each time you
turn on your phone. It can be your
name, a reminder, etc. To save the
note, press Options, then Save. To erase the note, press
Options, then Erase.
26
6. Emergency calls
1
2
If the phone is not on, switch it on.
Press and hold the
the phone for calls.
key for several seconds to ready
3
4
Key in the emergency number for your present location
(e.g. 911 or other official emergency number). Emergency
numbers vary by location.
Press Call.
IMPORTANT!
This phone, like any wireless phone, operates using radio
signals, wireless and landline networks as well as user-
programmed functions which cannot guarantee connection
in all conditions. Therefore you should never rely solely
upon any wireless phone for essential communications
(e.g. medical emergencies).
Remember, to make or receive any calls the phone must be
switched on and in a service area with adequate signal
strength. Emergency calls may not be possible on all wireless
phone networks or when certain network services and/or
phone features are in use. Check with local service providers.
If certain features are in use (Keyguard, call restrictions, etc.),
you may first need to turn those features off before you can
make an emergency call. Consult this document and your
local cellular service provider.
When making an emergency call, remember to give all the
necessary information as accurately as possible. Remember that
your wireless phone may be the only means of communication
at the scene of an accident - do not cut off the call until given
permission to do so.
27
Emergency key 9
Use Menu 4 1 1 to turn on this feature. When this feature is
on, the phone attempts to make an emergency call when you:
•
•
press and hold the 9 key, or
press 9, then press Call.
Note: When Keyguard is active, the only way to make an
emergency call is to dial the emergency number, then press
Call.
Note: Official emergency numbers (for example, 911) vary
by location. Only one number is dialed automatically by
Emergency Key 9, and it might not be the proper number
in all circumstances.
IMPORTANT!
Emergency response teams are required to respond to all
emergency calls they receive, whether the caller is able to
speak to the dispatcher or not. Accidental dialing of 911 may
prevent an emergency team from responding to an actual
emergency.
When your phone is not in use, please activate Keyguard,
especially if the Emergency key 9 feature is enabled.
28
7. Advanced functions
Network feature setting
Call forwarding, call waiting, and send own number are
network services available through your service provider.
These features do not appear in your phone’s Network
services menu until you save the related feature code(s)
given to you by your service provider. After you save the
feature activation or cancellation code, the feature appears
in the phone’s menu and you can use the menu to turn the
feature on or off.
Note: Feature codes can be saved only when your primary
phone number (NAM 1) is selected. See page 33.
Adding feature activation codes to the menu
To save a feature activation code, press Menu 4 4 2. At the
Feature code prompt, enter the feature activation code,
then press OK. Scroll to the feature that the code applies to,
then press Select. (If the feature is call forwarding, choose
one of the four types of call forwarding.) Finally, scroll to
Activate, then press OK.
Activate will now appear in the menu for that feature.
Adding feature cancellation codes to the menu
To save a feature cancellation code, press Menu 4 4 2. At the
Feature code prompt, enter the feature cancellation code,
then press OK. Scroll to the feature that the code applies to,
then press Select. (If the feature is call forwarding, choose
one of the four types of call forwarding.) Finally, scroll to
Cancel, then press OK.
Cancel will now appear in the menu for that feature.
In-call menu
When you are in a call, the function of the Navi™ key is
End. However, your phone has an in-call menu that allows
you to perform several functions while in a call. To use the
29
in-call menu, press
while you are in a call, then press
Options. Press
to scroll to the first item in the menu, or
to scroll to the last item in the menu.
The in-call menu is:
Answer
answer a waiting call
Swap
End
switch between two calls
end all calls
New call
Connect all
Phone book
Menu
make a call when you have one in progress
connect all active calls
access the phone book
access your phone’s menu
send touch tones
Touch tones
Mute/End mute mute/unmute the phone’s microphone
Making/receiving multiple calls
Making a new outgoing call
While you are in a call, select New call from the in-call menu.
Enter the number (or press Search to locate the number in the
phone book), then press Call. The first call is automatically
put on hold while you are in your new call.
Note: This feature might not be supported in your network.
Contact your service provider for details.
Three-way calling
Note: This feature might not be supported in your network or
might work differently than described. For more information,
contact your service provider.
To create a three-way call, call the first person. Then select
New call from the in-call menu, enter or find the phone
number of the second person, press OK and then press Call.
The first person is put on hold. After the second person
answers, choose Connect all from the in-call menu. Now all
three of you can talk to each other at the same time.
Ending calls
Press End or select End from the in-call menu.
30
Note: The wireless network does not support ending individual
calls when more than one call is in progress.
Call waiting
Call waiting is a network service that allows you to receive
an incoming call when you’re already in a call. Contact your
service provider for details.
Answering a waiting call
Note: Call waiting is a network service that requires a
subscription from your service provider.
If you are in a call with someone and another person calls
you, the function of the Navi™ Key changes from End to
Options. Press Options. The in-call menu appears with
Answer selected. Press OK.
Swapping between calls
When you are in a call and you receive an indication of a
waiting call, select Answer from the in-call menu. Your first
call will be put on hold. To swap back to the first call, select
Swap from the in-call menu.
Cancelling call waiting: standard method
To cancel call waiting before making a call, you must get the
call waiting cancellation code from your service provider.
1
Dial the code for cancelling call waiting followed by the
phone number you want to call.
2
Press Call.
Example: If the code for cancelling call waiting is *810
and the number you want to call is (214) 555-1234, dial
*8102145551234, then press Call.
Cancelling call waiting: menu method
You can save the code for cancelling call waiting given by
your service provider and then use Menu 4 4 4 2 to cancel
call waiting. See ‘Adding feature cancellation codes to the
31
Call forwarding
Call forwarding is a network service that lets you forward
your incoming calls to another phone number. Check with
your service provider for details and feature codes.
Activating call forwarding
Standard method
To activate call forwarding, you must get the call forwarding
activation code from your service provider.
1
Dial the code for activating call forwarding followed by
the phone number to which you want to forward your
calls.
2
Press Call.
Example: If the call forwarding activation code is *71 and
the number you want to forward calls to is (214) 555-1234,
dial *712145551234, then press Call.
Menu method
You can save the code for activating call forwarding and
then use the menu to activate call forwarding. See ‘Adding
Cancelling call forwarding
Standard method
To cancel call forwarding, you must get the call forwarding
cancellation code from your service provider.
1
Dial the code for cancelling call forwarding (for example,
*710).
2
Press Call.
Menu method
You can save the code for cancelling call forwarding and
then use the menu to cancel call forwarding. See ‘Adding
32
1-touch dialing
This feature allows you to make phone calls quickly and
easily with the touch of a button. Once you have assigned a
phone number to a number key (2 through 8), you can press
and hold that key to dial the number. (You can also press the
number key briefly and then press Call.)
Note: Keys 1 and 9 are used exclusively for dialing your voice
mailbox and for attempting emergency calls, respectively
page 27).
Assigning numbers to keys
Before you can assign a phone number to a key, the phone
Then follow the steps below.
1
2
3
Press Menu 1 6.
Scroll to the desired key, then press Assign.
Press
or
to choose the name you want to assign
to the selected key, then press Select.
If a key already has a number assigned to it, you can press
Options and then view, change, or erase the number
assignment.
Making calls using one-touch dialing
Press and hold a number key (2 through 8) for a few seconds
to call the number assigned to it. Your phone finds the
phone number, displays it briefly, then dials it.
You can also enter the number of the 1-touch dialing key
(for example, 2) and press Call.
Choosing your phone number
(NAM selection)
Your service provider can set up your phone to have two phone
numbers that are activated in different service areas—for
example, one number for the Dallas area and one number
for the Chicago area.
33
A number assignment module, or NAM, consists of a phone
number and network information that the service provider
programs into your phone. When you select a NAM, you’re
not only selecting a phone number, you’re also selecting a
home system in which you will not be charged roaming fees.
The two NAMs are not equal. Some features, such as system
page 29), are available only when the primary NAM is
selected.
Use Menu 4 5 to select a NAM.
Send own number
This network service allows you to hide your phone number
from a person you are calling who has Caller ID. (If for some
reason your network prevents phone numbers from being
displayed, you may be able to use this feature to show your
number to the person you are calling.) Contact your service
provider for feature codes for showing/hiding your phone
number.
Standard method
1
Dial the feature code followed by the number you want
to call.
2
Press Call.
Example: If the feature code to hide your number is *67 and
the number you want to dial is (214) 555-1234, dial
*672145551234, then press Call.
Menu method
You can save the feature code given by your service provider
so that Send own number appears in your phone’s menu,
This feature must be activated before each call.
Yes displays your number to the person you are calling.
No prevents your number from being shown to the person
you are calling.
34
Calling card calls
Before you can make a call using a calling card, you have
to enter your calling card information into the phone.
To make a call using a calling card:
1
Enter the phone number, including any prefix (such as 0
or 1) that your calling card may require when you make
a calling card call. See your calling card for instructions.
2
3
4
Press and hold Call for a few seconds until your phone
displays Card call.
Your phone displays Wait for tone, then press OK.
Wait for the tone, then press OK.
Your phone displays Wait for tone, press OK again.
Wait for the tone again, then press OK.
System selection
Your phone is capable of working in residential, private, and
public systems. You can choose how your phone selects a
network to use.
This feature is Menu 5 in your phone. The default is Automatic,
which means your phone automatically searches for networks
available to you and chooses the appropriate one. Every time
you switch on your phone, Automatic is selected.
If you choose Manual, your phone displays a list of available
and unavailable networks. (You can’t use unavailable networks.)
Scroll through the choices and press OK when you reach the
one you want.
If you choose New Search, your phone begins a new search
for new private and residential systems. When it finds the
best new system, it displays it. You can then select it or start
another search by pressing Next.
Note: The Manual and New search features can be used
only when your primary phone number (NAM1) is selected.
35
To switch from private to public
If you are in a private system and want access to a public
system, press and hold Menu when you are not in a call.
Your phone will display Search public systems? Press OK
and your phone will use the public system for the next
outgoing call. After the call it will revert to Automatic
system selection.
Automatic answer
This feature is available only when your phone is connected
to a headset or to an approved handsfree car kit equipped
with the ignition sense option, with the ignition on.
When automatic answer is turned on, your phone answers
incoming voice calls after one ring. Use Menu 4 1 4 to turn
this feature on or off.
Note: if the ringing type is set to Silent or Beep once, the
automatic answer will not work.
Touch tones
Your phone can generate various sounds, called touch tones,
when the keys are pressed.
Touch tones can be used for many automated services such
as checking voice mail, movie times, and airline arrival/
departure times.
Note: Sending confidential information over the air using
touch tones is not recommended.
Setting manual touch tone length
Use Menu 4 2 1 1 to set the length of touch tones created
when you press a key:
Continuous means the tone sounds for as long as you press
and hold the key.
Fixed sets the tone length to one tenth of a second, regardless
of how long you press and hold the key.
Off turns off touch tones. No tones will be sent when you
press the keys.
36
Setting automatic touch tone length
Use Menu 4 2 1 2 to set the length of touch tones sent
automatically by the phone to Short (one tenth of a second)
or Long (half a second).
Saving touch tone strings
Touch tone strings can be used for sending and receiving
information with your phone. Save touch tone strings the
For example, you can save your office voice mailbox number
along with your password for easy access to your messages.
Sending touch tone strings
1
During a call, press
display.
to clear any numbers from the
2
3
4
Press Options.
Scroll to Touch tones, then press OK.
Enter or find the touch tone string, then press OK.
Restore factory settings
You can use Menu 4 2 3 to reset many of the settings in
your phone to their factory defaults (as in a new phone).
You will be required to enter the security code.
Note: The phone book, language setting, call timers, security
code, and lock code are not affected.
37
8. Phone book
Your phone allows you to save 100 phone numbers and
associated names so they are right at your fingertips for
easy dialing.
Saving names and numbers
Saving a name and number is easy!
Just enter the phone number, press
or
, then press Save. Enter a
name if you wish, then press OK.
Each name may consist of up to
16 characters and each phone number may consist of up to
32 characters.
Saving a number quickly
To save a number quickly, enter the phone number, press
or
, then press and hold Save. The number is saved
to your phone book and you can add a name to it later
Saving a name and number while in a call
To save a name and number while in a call:
1
2
3
4
5
6
Press
.
Press Options.
Scroll to Phone book, then press OK.
Scroll to Add new, then press Select.
Enter a name if you like, then press OK.
Enter the phone number, then press OK.
The entry is displayed in your phone list. Press Call to call
the number or
to clear the screen (the current call
will not be affected).
38
Notes about saving names
•
A name may appear only once in memory. If you try to
save a name that already exists in memory, the phone
asks if you want to replace the existing name.
•
If you try to save a phone number and your phone book
is full, you are given the option to replace an existing
entry. Scroll to the entry you want to replace and press
OK, or press
to cancel.
Finding names and numbers
There are several ways to find names and numbers in your
phone book.
From the start screen
Press
to access your phone book, then scroll to the
desired name/number.
Tip: You can also press the number key that corresponds
to the first letter of the name. The first matching entry
is displayed at the top of the screen.
Using the Phone book menu
Press Menu 1 1, enter the first few
letters of the name, then press OK.
Your phone displays the first matching
entry at the top of the screen.
While performing other functions
Say you want to forward your phone
calls to a number that is saved in your
phone book. When you are prompted
to enter the phone number, you can
find it instead—simply press Search to
access your phone book.
39
Editing names and numbers
To edit phone book entries, press Menu 1 3, scroll to the
entry you want to edit, then press Edit. Edit the name and
number as needed.
Erasing names and numbers
Use Menu 1 4 to erase entries from your phone book. One by
one lets you select one entry at a time to be erased. Erase
all erases your entire phone book (you will be required to
enter your security code first).
Scrolling view
Use Menu 1 5 1 to choose a scrolling view for your phone
book (Name list, Name+number, or Name only).
Tip: If your phone book’s scrolling view is set to
Name list or Name only, you can view the phone
number associated with a name by pressing and
holding the
key.
Checking available memory
Use Menu 1 5 2 to see how many memory locations are free
and how many are being used. (Each memory location holds
one phone number and associated name.)
40
9. Call log
For your convenience, the call log (Menu 3) saves a list of
phone numbers you have dialed, and can show you how
much time you have spent on the phone. If you subscribe to
the caller ID network service, the call log also records the
phone numbers of missed calls and received calls. Contact
your service provider for details.
The Options key
When you access Missed calls, Received calls, or Dialed
calls and press Options, a list of options appears on your
phone’s display.
Call dials the number.
Call time shows the time of the last call. (Your phone’s clock
Edit number allows you to edit the number.
Save allows you to enter a name for the number, edit the
number if needed, and save both to your phone book.
Erase erases the number from the call list.
View number displays the associated phone number if only
the name is currently displayed.
Missed calls
If you subscribe to the caller ID network service, your phone
automatically stores the last 10 numbers that have tried
unsuccessfully to reach you (as long as the caller allowed
his or her number to be shown to you).
When the display says Missed calls
Press List. If you have missed more than one call, you can
scroll through the list of numbers. To dial the displayed
number, press Options, then choose Call.
41
Viewing the missed calls list at any time
Use Menu 3 1 to view the missed calls list at any time.
To dial a number, press Options, then choose Call.
Received calls
If you subscribe to the caller ID network service, your phone
automatically stores the phone numbers of the 10 most
recent calls you’ve answered. Use Menu 3 2 to view the
received calls list. To dial a number, press Options, then
choose Call.
Dialed calls
Your phone automatically stores the last 10 numbers you’ve
dialed. From the start screen, press
to access the dialed
calls list. Scroll to the desired number, then press Call.
the dialed calls list by pressing Menu 3 3.
Clearing call lists
Use Menu 3 4 to clear the missed, received, and/or dialed
call lists.
Call timers
Use Menu 3 5 to see the amount of
time you’ve spent in calls. Times are for
the currently selected phone number;
your phone has a separate timer for
each phone number, or NAM
Note: The actual time invoiced for calls by your service provider
may vary, depending upon network features, rounding-off for
billing, and so forth.
Viewing call timers
Use Menu 3 5 to view the various call timers.
42
Last call is the duration of the last call, or current call if
applicable.
All calls is the duration of all calls since the timers were last
reset.
Life timer displays the duration of all calls for the life of
your phone and cannot be reset.
Setting timers back to 0
Use Menu 3 5 4 to clear call timers. You will be required to
enter your security code.
Displaying the current call timer during calls
1
2
3
4
Press Menu 3 5 1.
Press Details.
Press Select.
Scroll to On, then press OK.
During a call, the amount of time spent in that call will be
displayed.
43
10. Voice messages
Voice mail is a network service that allows callers to record
a message when you cannot be reached. You can then call
your voice mailbox and retrieve your messages.
Saving your voice mailbox number
When you subscribe to voice mail, your service provider will
give you a voice mailbox number. You should save this number
so you can call your voice mailbox by pressing and holding
the
key. See ‘Voice mailbox number’ on page 25.
Listening to new voice messages
When you receive a voice message, your phone may notify
you by beeping, displaying the voice message indicator
, and displaying New voice message. The phone may
display the number of messages if there is more than one.
Note: The method of notification depends on your service
provider.
When your phone notifies you that you have a new voice
message, press Listen. Your phone dials your voice mailbox
number, if you have saved it.
Calling your voice mailbox at any time
Once you have saved your voice mailbox number, you can
press and hold the
key to dial your voice mailbox.
44
11. Text messages
The text message network service allows you to write, send,
forward and reply to text messages. Also, you can receive
text messages from a variety of sources, such as a Web page
set up by your service provider.
Note: The availability of text messages may vary according to
your wireless service provider. Contact your service provider
for details.
Reading messages
When you receive a text message, the phone displays the
indicator, either Message received or New emergency
message (if an emergency message has been received), and
makes a sound (depending on the message alert tone; see
To read the message, press Read. This takes you to the
Inbox, with the new message selected. Press Read again.
If necessary, use the scroll keys to read the entire message.
After reaching the end of the message, use the scroll keys to
view the sender’s name or phone number, and the date and
time the message was received.
Options when reading messages
Several options are available while you’re reading a message.
Just press Options, scroll to the one you want, then press OK.
Read next allows you to read the next message.
Erase deletes the message. Press OK to confirm the deletion
(or
to cancel).
Save saves the message in the Saved folder.
Call back calls any displayed phone number included in the
message. If more than one number was included, a list of
numbers is displayed. Choose one and press Call.
Forward forwards the message to another person. That person
must have the appropriate message service.
45
Reply provides a screen where you can write a reply to a
message.
When you’ve seen the last new message, the
disappears.
indicator
About the Inbox
The Inbox holds text messages that have not been deleted or
saved. Use Menu 2 11 to access the Inbox at any time.
You will see a list of message headers. The
of the header indicates that a message has been read.
The icon indicates that a message has not been read.
icon in front
Scroll to the desired message, then press Read.
About the Saved folder
The Saved folder holds up to 30 saved text messages.
Use Menu 2 1 2 to access the Saved folder and read
saved messages.
Storage of incoming messages
When you have an incoming text message and your phone’s
memory is full, one or more low-priority messages, which
have been read, will automatically be deleted in order to
receive the new text message. Messages are usually deleted
from your Inbox, but an emergency message may cause
messages to be deleted from the Saved folder.
If the message memory is still full, your phone will display
No space: message waiting. You can clear this notification
by pressing OK. You should delete one or more old messages
to make room for the new message. The network will re-send
the message at a later time.
Erasing all text messages
Use Menu 2 1 6 to access the Erase all option for Text
messages. Erase all allows you to permanently erase all
messages from one of the following categories:
All read
Erases all read messages in the inbox
All in inbox Erases all messages in the inbox
46
All saved
Erases all messages stored in the Saved folder
All in outbox Erases all messages in the outbox
Writing and sending text messages
You can write a text message using your keypad. Once you
have written a message on your screen, you will have options
for sending your message.
Note: Your 5165 supports writing and sending text messages
in English, Hebrew, Portuguese and Spanish. Contact your
service provider for details of feature availability.
Writing a text message
1
Press Menu 2 1 3 and select Write message.
2
Write your text message by entering letters and numbers
from your keypad.
Your phone has a special feature for writing messages,
called Predictive text input. For more information, see
3
The function of the Navi™ key will change to Options.
Your Options menu is:
Send
send the message
Exit
return to the Text messages menu
clear all entered text from the screen
choose a setting for your message
store the text message to Saved
turn on/off the predictive text input
add a new word in the dictionary
Clear screen
Settings
Save
Dictionary
Spell moded
Insert numberd insert a number in a message
Insert symbold insert a special character in a message
Matchesd
check the spelling options in the
dictionary for a word you have written
d
Visible only when dictionary activated
47
Sending a text message
1
2
3
Write a text message and press Options.
To send the message, highlight Send and press OK.
Enter the phone number (or press Search to locate the
number in the phone book), then press Send.
Message settings
This network feature allows you to mark your text message
as urgent, place your number within the text message, or
request a read receipt. This is a network feature. Contact
your service provider for more information.
Message settings are located in the Write new options menu
as Settings. You may select or deselect the following settings
by pressing Mark or Unmark.
Urgent
notify recipient that your message is
important
Read receipt notify you that the recipient has opened your
message
Callback no. place your phone number within the message
Received Urgent messages are indicated with an exclamation
mark (!) in front of the message.
Note: Callback no. is the default setting for your phone.
About the Outbox
Use Menu 2 1 5 to access the Outbox. The Outbox stores
messages that were sent successfully as well as messages that
were sent unsuccessfully. The
heading shows that you have sent the message to the text
message center. The icon shows that you attempted to
icon in front of a message
send the message, but your attempt was unsuccessful.
Press Read to read the selected message.
Forwarding and replying to a message
You can forward or reply to messages which are located in
the Inbox, Saved folder or Outbox. Highlight the message
and press Read. The Options menu appears.
48
Forwarding a text message
1
2
3
4
5
Highlight the message that you want to forward.
Press Read, then press Options.
Scroll to Forward, press OK.
Scroll to either As message or As e-mail, press OK.
Send the message as you normally would.
Replying to a text message
1
2
3
4
5
Highlight the message that you want to reply to.
Press Read, then press Options.
Scroll to Reply, press OK.
Scroll to either As message or As e-mail, press OK.
Send the message as you normally would.
Sending and receiving business cards
You can send and receive electronic business cards. A business
card consists of a name, phone number and e-mail address.
You can save received business cards in your phone book.
Sending a business card
1
Press Menu 1 7.
2
Now you are in your phone book. Scroll to find the name
whose business card information you want to send.
3
4
Choose the name and press Send.
Enter the phone number to which you want to send the
business card (or press Search to locate the number in
the phone book) , and press Send.
Tip: Save your own business card in the phone book.
When you need to send one, it is ready.
Viewing a received business card
When you receive a business card, the phone displays the
text Business card received and sounds an alert (depending
Note: If you press
at any time before saving the
business card, the business card will be deleted!
49
1
When your phone displays Business card received, press
Options.
2
3
Select Show and Press OK.
Scroll through the available information.
Saving a viewed business card
1
2
3
After viewing the business card, press
, scroll to
Save, then press OK.
At the Name prompt, edit the name if you want to, then
press OK.
At the Number prompt, edit the number if you want to,
then press OK.
Deleting a viewed business card
•
After viewing the received business card, press
Business cards are saved in your phone book and you can
delete them the same way you delete phone book entries.
50
12. E-mail messages
You can use your phone to send and receive e-mail messages.
This means you no longer need to be at your computer to
send or receive messages.
Saving e-mail addresses
You can add an e-mail address to a name you already have
in your phone book. Or, you can add a name and address as
a new entry.
Save an e-mail address for an existing name
1
2
3
Press Menu and Select.
Scroll to Edit and press Select.
Scroll to the name you want to add an e-mail address to
and press Edit.
4
5
6
When prompted Name, press OK.
When prompted Number, press OK.
When prompted E-mail address, enter the e-mail
address.
To add special characters (@ and . ), press
to get to
the special character screen. Scroll to the character you
need and press Use.
7
Press OK.
For more information, see ‘Editing names and numbers’ on
Add a new e-mail address
1
2
3
Press Menu and Select.
Scroll to Add new and press Select.
When prompted Name, enter the name for the e-mail
address. Press OK.
4
When prompted Number, enter the phone number for
the e-mail address or press OK to leave it blank.
51
5
6
When prompted E-mail address, enter the e-mail address.
To add special characters (@ and . ), press to get to
the special character screen. Scroll to the character you
need and press Use.
Press Save.
For more information on saving, editing and erasing phone
book entries, see ‘Phone book’ on page 38.
Sending e-mail messages
Before you can send and receive e-mail messages, you need
to have the e-mail gateway number saved in your phone.
Contact your service provider for more information.
1
Press Menu 2 1 4
Note: Please contact your service provider in the event your
are prompted for the e-mail gateway number.
2
When prompted E-mail address, enter the e-mail
address or press Search to scroll through the e-mail
addresses in your phone book. Press OK to choose the
e-mail address and press OK to confirm the address.
3
When prompted Subject, enter a subject for your e-mail
message, or press OK to leave it blank.
The screen you see now has the
cursor is blinking after the e-mail
address and the subject text.
In the top right corner a number
shows the characters you have left
to use in your message.
Note: The maximum number of characters for message
length varies. Contact your service provider for details.
4
Write your message either using the standard text input
5
Press Options and scroll to Send. Press OK.
52
Options for a completed message
Send
Save
Erase
Exit
send the message
save the message in the saved folder
clear the message text
erase the message and return to the
Start screen
Dictionary
activate or deactivate the dictionary
add a new word in the dictionary
Insert numberd insert a number in the message
Spell moded
Insert symbold
Matchesd
insert a special character in the message
check the spelling options in the
dictionary for a word you have written
d
Visible only when dictionary activated
Forwarding and replying to e-mail
messages
1
2
3
4
5
If the message is not on the screen, press Menu 2 1 1
Scroll to the message you want to use and press Read.
Press Options, scroll to Forward or Reply, and press OK.
Scroll to As e-mail and press OK.
When prompted for the e-mail address, enter the address
or press Search to scroll through the list of e-mail addresses
in your phone book. Press OK to choose the address and
press OK to confirm the address.
6
7
Enter a subject line and press OK.
When the message box appears, write your reply or the
message to the forwarded e-mail.
8
Press Options, scroll to Send and press OK.
53
13. Extra features
Alarm clock
The alarm clock feature is based on
your phone’s internal clock and sounds
an alert at a time you specify.
Setting the alarm clock
Use Menu 7 1 to turn the alarm clock on or off.
Note that when you’re entering the alarm time, use two
digits for both hours and minutes (for example, enter 1:30
am/pm, you will be asked to choose am or pm.
Note: The
key does not work on this screen. If you make
a mistake, re-enter all four digits.
automatic time update, see page 22.
Alarm volume
The alarm volume is determined by the current ringing volume.
However, if you have manually set the ringing option (see
sounds a quiet beep.
When the alarm sounds
•
To shut off the alarm, press any key except Snooze.
•
If you press Snooze, the alarm sounds again in 10
minutes. To turn off the alarm before then, press Stop.
•
If you let the alarm sound for one minute without
pressing a key, it stops for 10 minutes, then starts again.
If you turn off the phone
If you turn off the phone and the alarm is set, the phone
switches itself on at alarm time, then the alarm sounds.
54
•
•
To shut off the alarm, press any key except Snooze.
The phone displays Keep the phone on? Press Yes to
keep it on or
to switch it off.
If you press Snooze, the phone turns itself off for 10
minutes, then the alarm sounds again.
REMEMBER! Do not switch on the phone when wireless phone
use is prohibited or when it may cause interference or danger.
Downloading ringing tones
You can download up to five ringing tones to replace the
Personal entries in your list of ringing tones. Contact your
service provider for details on feature availability.
Note: If you press
at any time before saving the ringing
tone, the ringing tone will be deleted!
Notification of received ringing tone
When you receive a downloaded ringing tone, your phone
displays Ringing tone received.
Listening to the received ringing tone
1
2
3
Press Options.
Scroll to Playback, then press OK.
Press Quit.
Saving the received ringing tone
1
When your phone displays Ringing tone received, press
Options.
2
3
4
Scroll to Save tone, then press OK.
Highlight the ringing tone you want to replace.
Press OK.
Deleting the received ringing tone
•
Scroll to Discard tone, then press OK.
The ringing tone is not saved in your list of ringing tones.
55
Games
Use Menu 6 to challenge yourself or a friend to the three
fun games in your phone. To pause a game, press
.
To resume, choose Continue.
REMEMBER! Your phone must be switched on to use this
function. Do not switch on the phone when wireless phone
use is prohibited or when it may cause interference or danger.
Memory
Reveal pictures to find pairs in as few tries as possible. Move
the cursor with the 2 (up), 4 (left), 6 (right), and 8 (down)
keys. Press the 5 key to reveal pictures. Once found, pairs
stay visible. Press the
revealed pictures or to move from the bottom right of the
screen to the top left. Press the key to jump to the left
key to jump to the right over
over revealed pictures or to move from the top left of the
screen to the bottom right.
Snake
Feed the snake with as many goodies as possible and watch
it grow. Use keys 2, 4, 6, and 8 to turn the snake toward
food. The longer the snake’s tail grows, the higher your
score. If the snake hits its own tail or the surrounding wall,
the game is over.
Logic
Find the secret combination of figures in a column. Possible
figures are shown at the top of the display. Press the 5 key
repeatedly to select a figure and the 2, 4, and 8 keys to move
the cursor. Once you think you have the right combination,
press the
key. The result appears as a set of marks above
the column. A correct figure in the right place gets a full
mark; a correct figure in the wrong place gets a half mark.
The game ends when the correct figures are in the right
place.
Tip: To copy a figure from the previous column, move
the cursor over it using the 2, 4, or 8 key, then press
the 5 key.
56
Predictive text input
This feature allows you to write text messages by pressing each
number key only once for each letter. Your phone has a built-in
dictionary that searches for the correct word. You can add
words (for example, the names that you use often) into the
dictionary.
Since the word shown on the screen changes after each key
stroke, try to disregard the word until you have keyed in all
the characters.
Turning on predictive text input
1
2
3
4
5
6
Press Menu 2 1.
Scroll to Write message, and press Select.
Enter a character using the keypad.
Press Options, scroll to Dictionary and press OK.
Scroll to the dictionary you want (for example, English).
Press OK.
T9 dictionary activated appears. (“T9” is the technical name
for predictive text input.) This means you can now use
predictive text input to enter messages.
The T9 icon
is also visible on your screen when the
feature is activated.
Turning off predictive text input
1
Repeat steps from 1 through 4 in “Turn on predictive
text input“.
2
Scroll to Dictionary off and press OK.
T9 dictionary deactivated appears.
Notes about predictive text input
If the word is correct
•
•
•
Insert a punctuation mark, if needed.
Press
to confirm the word and to enter a space.
Start writing the next word.
57
If the word is not correct
•
Press
then press
repeatedly until the desired word appears,
to confirm it.
OR
•
Press Options, scroll to Matches, then press OK. Scroll to
the correct word and press Use.
•
•
Press
to confirm the word and to enter a space.
Start writing the next word.
Add a desired word to the match list
If the ? character appears after a word, the word you intended
to write is not in the dictionary. You can add the word to
the dictionary.
1
Press Spell and enter the word(s) using standard text
input (press a key so many times that the correct character
appears on screen).
2
Press OK to save the word(s).
Insert symbols
1
Press and hold
.
OR
Press Options, scroll to Insert symbol and press OK.
The symbol screen appears, showing the special characters
available in your phone.
2
Scroll to the symbol you want and press Use.
Insert numbers
1
Press and hold
Enter the desired numbers, then press and hold
return to mode.
until
appears.
2
to
OR
1
Press Options, scroll to Insert number and press OK.
2
Enter the desired numbers, then press OK.
58
Prepaid service
Your service provider may offer prepaid service. This means
that you can sign up to become a prepaid customer and
obtain airtime by purchasing a Prepaid card which contains
a replenishment value. Contact your service provider for
details.
Note: Use of the Prepaid menu requires that your service
provider have access numbers available to check your
balance and replenish your account.
The prepaid menu makes it easy to manage your prepaid
account. You can easily check your account balance and
replenish (add money) to your account. Before you can
use the prepaid menu, you must activate it and enter your
access phone numbers.
Activating the Prepaid menu
You activate the Prepaid menu in the phone by contacting
your service provider. Once the menu is activated, the
confirmation screen Prepaid menu enabled appears.
The phone returns to the Prepaid menu. The Prepaid menu
is the last item in your phone’s menu listing. It is easy to
access by pressing Menu and
.
When the Prepaid menu is active, it replaces Keyguard as
Deactivating the Prepaid menu
You deactivate the Prepaid menu by contacting your service
provider. Once the menu is deactivated, the confirmation
screen Prepaid menu disabled appears and the phone returns
to the Start screen.
Saving access phone numbers
After you have activated the Prepaid menu, you need to save
the access phone numbers for checking the balance and for
adding money to your account. After saving these numbers,
you will be able to use these services through your Prepaid
menu. Contact your service provider for the access numbers.
59
1
2
3
Press Menu and
, then Select.
Select Save access phone numbers.
When prompted for the balance number, enter the phone
number given to you by your service provider.
4
5
Press OK.
When prompted for the replenish number, enter the
phone number given to you by your service provider.
6
Press OK.
Checking your Prepaid balance
1
2
3
Press Menu and
, then Select.
Select Check account balance.
Listen to the audio notification of the balance in your
Prepaid account.
4
Press End to end the call.
Adding money to your Prepaid account
To be able to add money to your Prepaid account, you need
a Prepaid card. Contact your service provider for Prepaid
card availability.
1
2
3
Press Menu and
, then Select.
Select Add money to account.
When prompted for the Prepaid card number, enter the
number on your Prepaid card.
4
5
Listen for message, then press OK.
Wait for notification, then press End.
If the operation was not successful, you need to restart from
step 2.
Low balance on your Prepaid account
A low balance on your Prepaid account is indicated by an
audio notification before or during your call. This message
from the service provider may be repeated several times.
Contact your service provider for details.
60
Zero balance on your Prepaid account
A zero balance on your Prepaid account during a call ends
your call.
A zero balance on your Prepaid account before a call prevents
both incoming and outgoing calls. You may hear an audio
notification about your zero balance when you try to make
a call.
Making calls using Prepaid service
1
Dial the number you want to call.
2
You may hear an audio notification of your Prepaid
account balance.
3
If the account is active with a positive balance, the call
is connected.
If the account is active with a zero balance, the call is
not connected. You may hear an audio notification that
you have a zero balance in your account.
4
5
At the end of the call, you may hear an audio notification
of the current balance in your account.
Press End to end the call.
61
14. Security features
Access codes overview
Access codes consist of the lock code and security code.
When you get your phone, you should change these codes
from their defaults, write down the new codes, and keep
them in a safe place away from the phone. Avoid using access
codes that are similar to emergency numbers, such as 911,
to prevent accidental dialing of the emergency number.
Lock code
Your phone’s lock code is used to lock and unlock your phone.
The default lock code is 1234. Use Menu 4 3 2 3 to change
the lock code.
When the phone requires the lock code, it displays Enter
lock code: Enter the code, then press OK.
If you enter a wrong lock code five times in succession, your
phone prompts you for the security code.
Security code
The security code is required to restrict calls and to restore
factory settings. The default security code is 12345.
Use Menu 4 3 2 4 to change the security code.
When the phone requires the security code, it displays
Security code: Enter the code, then press OK.
If you enter an incorrect security code five times in succession,
the phone will not accept any input for the next five minutes.
Restricting calls
Use Menu 4 3 1 to restrict outgoing or incoming calls.
This is handy if you want to lend your phone to someone but
don’t want them to make long-distance or other expensive
calls.
62
Restricting incoming calls
Choose Restrict incoming calls to prevent your phone from
receiving incoming calls. Enter your security code, then
press OK. Press Mark, then press
change (or to cancel).
. Press Yes to save this
Note: This feature requires the caller ID network service, and
the caller’s ID must be available to the phone in order for the
restriction to work.
Allowing incoming calls
To allow incoming calls once again, choose Restrict incoming
calls and enter your security code. Press Unmark, then press
. Press Yes to save this change (or
to cancel).
Restricting outgoing calls
You can create a list of numbers to which outgoing calls
cannot be made. A call restriction can consist of an entire
phone number, an area code, etc. When the restriction is
selected, calls cannot be made to any number beginning
with those digits. For example, entering 2145551234 will
block calls to (214) 555-1234 only. 1 will block all calls
starting with 1, including long distance calls and 1-800
calls. 1800 will block 1-800 calls only.
Adding numbers to the restricted outgoing calls list
To prevent your phone from making outgoing calls, choose
Restrict outgoing calls. Enter your security code, then press
OK. Continue with the steps illustrated below.
1
Add restriction is selected.
Press OK.
2
Enter the phone number, area code,
etc. to which you want to restrict
calls, then press OK.
63
3
If you want, give a name of up to
10 characters to the restriction
(such as Joey, Long dist, or 1-800
#s), then press OK.
The entry is added to your list of
restricted numbers.
Allowing calls to a number on the list
If you later decide to allow calls to a
restricted number, press Select to see
your list of numbers. Press Unmark to
remove the restriction. (The number
remains in the list so that you can
restrict it again later by pressing Mark.) When you’re done,
press
. Press Yes to save your changes (or
to cancel).
Making changes to the restricted outgoing calls list
To edit or completely erase an entry in the list, choose Edit
or Erase, select the entry you want to edit or erase, and
follow the instructions on the screen.
Phone lock
You can prevent unauthorized use of your phone by locking
it. When your phone is locked, only incoming calls and calls
to the unlocked phone number (see below) are allowed.
The memory and menu are unavailable.
Note: Calls may still be possible to emergency numbers.
How to lock your phone
press OK. Scroll to On, then press OK.
How to unlock your phone
Press Menu, enter the lock code, then press OK.
Answering a call when the phone is locked
Press Answer.
64
Saving the unlocked phone number
Use Menu 4 3 2 2 to save a number that may be called even
when your phone is locked. You will be required to enter the
lock code.
Calling the unlocked phone number
Press
or
, or manually enter the number exactly as it
is saved, then press Call.
65
15. Accessories
An extensive range of accessories
is available for your phone. You
can select the accessories that best
suit your specific communication
needs. For availability, see your
local authorized Nokia dealer.
A few practical rules for accessory
operation:
•
•
Keep accessories out of small children's reach.
When you disconnect the power cord of any accessory,
grasp and pull the plug, not the cord.
•
•
Check regularly that all wireless phone equipment in
your vehicle is mounted and operating properly.
Installation of complex car equipment must be
completed by qualified personnel only.
WARNING!
Use only batteries, chargers and accessories approved by
the phone manufacturer for use with this particular phone
model. The use of any other types may invalidate any
approval or warranty applying to the phone, and may be
dangerous.
Nokia Xpress-on™ color covers
Your phone’s Xpress-on™ cover is available in several
fashion colors. Extra covers may be purchased from your
authorized Nokia dealer.
You can use the new 5165 covers with the 5160 phones.
The new cover requires a matching keypad. Also, you can
use the 5160 covers with the 5165 phones.
Note: Always store the phone with cover attached.
66
Changing covers
When changing covers, don’t use the phone’s antenna as
leverage!
1
Switch off the power and disconnect the phone from
the charger or any other device.
2
Using a coin, depress the
colored tab on the top of
the phone and slide the
color cover forward.
3
Remove the cover.
4
Remove the rubber
keypad from the back of
the cover. Place it into
the back of the new
cover.
67
5
Place the bottom of the
cover against the bottom
of the phone. Make sure
all three sets of plastic tabs
line up with their respective
slots, as shown at left.
Close the cover and snap it
shut all the way around
the edge of the phone.
Batteries
Several batteries are available for your phone:
•
•
•
•
•
BPS-1 Ultra Slim Li-Polymer 600 mAh
BLS-2N Extended Li-Ion 900 mAh
BMS-2S Extended NiMH 900 mAh
BMS-2V Vibrating NiMH 900 mAh
BLS-4 Ultra Extended Li-Ion 1500 mAh
Charging times
The table below displays approximate battery charging times.
These charging times will charge your phone to about 80%
of its capacity, and the battery strength indicator will stop
scrolling. If you wish to obtain 100% battery capacity,
please allow another two hours for “maintenance” charge.
Standard
Rapid Travel
Charger
ACP-9U
Rapid Cig.
Lighter
Charger LCH-9
Travel
Charger
ACP-7U
Battery
BPS-1 Ultra Slim
Li-Polymer 600 mAh
2 hours,
30 minutes
1 hour, 20 minutes
BLS-2N Extended Li-Ion
900 mAh
2 hours
BMS-2S Extended NiMH
900 mAh
4 hours
1 hour, 30 minutes
3 hours, 30 minutes
BMS-2V Vibrating NiMH
900 mAh
BLS-4 Ultra Extended Li-Ion
1500 mAh
5 hours
68
Talk and standby times
The table below displays approximate talk and standby times.
Variations will occur depending on network settings and usage.
Talk Time
Standby Time
Digital Analog
66 - 20 -
Battery
Digital
Analog
BPS-1 Ultra Slim
1 hr, 20 min -
40 min -
Li-Polymer 600 mAh
2 hrs, 10 min 1 hr, 15 min
133 hrs
33 hrs
BLS-2N Extended
Li-Ion 900 mAh
BMS-2S Extended
NiMH 900 mAh
2 hrs -
1 hr -
100 -
200 hrs
30 -
50 hrs
3 hrs, 15 min 1 hr, 45 min
BMS-2V Vibrating
NiMH 900 mAh
BLS-4 Ultra Extended
Li-Ion 1500 mAh
1 hr, 30 min -
3 - 5 hrs
170 -
50 -
83 hrs
2 hrs, 45 min 335 hrs
Chargers and other accessories
WARNING!
This apparatus is intended for use when supplied with power
from the Standard Travel Charger (ACP-7U), Rapid Travel
Charger (ACP-9U), or Rapid Cigarette Lighter Charger
(LCH-9). Other usage will invalidate any approval given to
this apparatus and may be dangerous.
The following chargers and other accessories are available
for your phone; please see your dealer for details. Also, refer
to any accessory options manual that may have been included
in your sales package for the entire line of Nokia Original
Accessories.
Note: When a charger is not in use, disconnect it from the power
source. Do not leave the battery connected to a charger for
longer than a week, since overcharging may shorten its life.
If left unused, a fully charged battery will discharge itself over
time.
69
ACP-7U Standard Travel
Charger
Use this durable and economical
charger to charge all battery options.
Plug the charger into a wall outlet
and connect the connector to the
bottom of your phone.
Check the charging status on the phone display.
Calls can be made during charging, but charging will stop
for the duration of the call.
Note: If the battery is completely empty, you cannot use the
phone until it has enough charge to operate.
The Standard Travel Charger is available for different voltage
levels and can also be used with the DCH-9 Compact Desktop
Charging Stand.
ACP-9U Rapid Travel Charger
The extremely light, functionally
designed Rapid Travel Charger charges
your phone battery quickly.
Plug the charger into a wall outlet and
connect the connector to the bottom of
your phone. Check the charging status
on the phone display. You can use your
phone while charging.
Operating within a voltage range of 100V-240V AC (50Hz-
60Hz), the Rapid Travel Charger is practically voltage-
independent in normal office and household use. Like the
Standard Travel Charger, the Rapid Travel Charger is compatible
with all battery options. The Rapid Travel Charger can also
be used with the DCH-9 Compact Desktop Charging Stand.
70
LCH-9 Rapid Cigarette Lighter Charger
The multivoltage Rapid
Cigarette Lighter Charger
allows you to charge your
phone when you travel. The
small charger's functional
design fits well with most car
lighters and interiors.
Charging times are the same as for the Rapid Travel Charger
ACP-9U. Calls can be made during charging.
A green light indicates that the Rapid Cigarette Lighter
Charger is ready to charge. Check the charging status on the
phone display. The input voltage is 12 or 24 V DC, negative
grounding.
The Rapid Cigarette Lighter Charger can be used with all
accessories available for your phone.
Avoid prolonged charging with the Rapid Cigarette Lighter
Charger when the car engine is not running. This may cause
the battery of your car to drain.
Note: In some cars the cigarette lighter plug is not provided
with power when the ignition is switched off. Verify that the
green LED light is lit.
DCH-9 Compact Desktop Charging Stand
Compatible with all battery
options, the Compact Desktop
Charging Stand can be used
with the Standard Travel
Charger ACP-7U or the Rapid
Travel Charger ACP-9U. The
Compact Desktop Charging
Stand provides mounting for
both the phone and a spare battery. Plug the charger into a
wall outlet and connect the connector to the back of the
Compact Desktop Charging Stand. Place your phone and/or
a spare battery in the stand to begin battery charging.
71
When the phone is charging, no lights are displayed on the
stand; check the charging status of the phone battery on
the phone display.
Charging moves to the rear slot once the front battery is
100% charged.
When the spare battery is charging, check the status indicator
on the left side of the charging stand. A red light indicates
that the battery is charging; a green light indicates that the
battery is charged to at least 80% of its capacity.
DCH-9 Rear Slot Charging Times
Using ACP-7U
Using ACP-9U
Battery
Front slot Front slot Front slot Front slot
empty
occupied
empty
occupied
BPS-1 Ultra Slim
Li-Polymer 600 mAh
4 hours,
30 minutes 30 minutes
6 hours,
4 hours,
30 minutes
3 hours
BLS-2N Extended
Li-Ion 900 mAh
BMS-2S Extended
NiMH 900 mAh
6 hours,
8 hours,
4 hours,
5 hours,
30 minutes 30 minutes 30 minutes 30 minutes
BMS-2V Vibrating
NiMH 900 mAh
BLS-4 Ultra Extended
Li-Ion 1500 mAh
15 hours,
45 minutes
10 hours,
30 minutes
12 hours
8 hours
The phone has the built-in intelligence to maintain the
battery, so there is no need for a discharge feature on the
stand.
72
16. Reference information
Important safety information
Traffic safety
Do not use a hand-held telephone while driving a vehicle. If using a
hand-held phone park the vehicle before conversing. Always secure
the phone in its holder; do not place the phone on the passenger seat
or where it can break loose in a collision or sudden stop.
The use of an alert device to operate a vehicle’s lights or horn on
public roads is not permitted.
Remember, road safety always comes first!
Operating environment
Remember to follow any special regulations in force in any area and
always switch off your phone whenever it is forbidden to use it, or
when it may cause interference or danger.
When connecting the phone or any accessory to another device, read
its user’s guide for detailed safety instructions. Do not connect
incompatible products.
As with other mobile radio transmitting equipment, users are advised
that for the satisfactory operation of the equipment and for the
safety of personnel, it is recommended that the equipment should
only be used in the normal operating position (held to your ear with
the antenna pointing over your shoulder).
Electronic devices
Most modern electronic equipment is shielded from radio frequency
(RF) signals. However, certain electronic equipment may not be
shielded against the RF signals from your wireless phone.
Pacemakers
Pacemaker manufacturers recommend that a minimum separation of
6 inches (20 cm.) be maintained between a handheld wireless phone
and a pacemaker to avoid potential interference with the pacemaker.
These recommendations are consistent with the independent research
by and recommendations of Wireless Technology Research.
Persons with pacemakers:
•
Should always keep the phone more than 6 inches (20 cm) from
their pacemaker when the phone is switched on;
•
Should not carry the phone in a breast pocket;
73
•
•
Should use the ear opposite the pacemaker to minimize the
potential for interference.
If you have any reason to suspect that interference is taking
place, switch off your phone immediately.
Hearing aids
Some digital wireless phones may interfere with some hearing aids.
In the event of such interference, you may want to consult your
service provider.
Other medical devices
Operation of any radio transmitting equipment, including cellular
phones, may interfere with the functionality of inadequately
protected medical devices. Consult a physician or the manufacturer
of the medical device to determine if they are adequately shielded
from external RF energy or if you have any questions. Switch off your
phone in health care facilities when any regulations posted in these
areas instruct you to do so. Hospitals or health care facilities may be
using equipment that could be sensitive to external RF energy.
Vehicles
RF signals may affect improperly installed or inadequately shielded
electronic systems in motor vehicles (e.g. electronic fuel injection
systems, electronic anti-skid (anti-lock) braking systems, electronic
speed control systems, air bag systems). Check with the manufacturer
or its representative regarding your vehicle. You should also consult
the manufacturer of any equipment that has been added to your
vehicle.
Posted facilities
Switch your phone off in any facility where posted notices so require.
Potentially explosive atmospheres
Switch off your phone when in any area with a potentially explosive
atmosphere and obey all signs and instructions. Sparks in such areas
could cause an explosion or fire resulting in bodily injury or even death.
Users are advised to switch off the phone while at a refueling point
(service station). Users are reminded of the need to observe restrictions
on the use of radio equipment in fuel depots (fuel storage and
distribution areas), chemical plants or where blasting operations are
in progress.
Areas with a potentially explosive atmosphere are often but not
always clearly marked. They include below deck on boats; chemical
transfer or storage facilities; vehicles using liquefied petroleum gas
(such as propane or butane); areas where the air contains chemicals
or particles, such as grain, dust or metal powders; and any other area
where you would normally be advised to turn off your vehicle engine.
74
Vehicles
Only qualified personnel should service the phone, or install the
phone in a vehicle. Faulty installation or service may be dangerous
and may invalidate any warranty which may apply to the unit.
Check regularly that all wireless phone equipment in your vehicle is
mounted and operating properly.
Do not store or carry flammable liquids, gases or explosive materials
in the same compartment as the phone, its parts or accessories.
For vehicles equipped with an air bag, remember that an air bag
inflates with great force. Do not place objects, including both installed
or portable wireless equipment, in the area over the air bag or in the
air bag deployment area. If in-vehicle wireless equipment is improperly
installed and the air bag inflates, serious injury could result.
Switch off your phone before boarding an aircraft. The use of wireless
telephones in an aircraft may be dangerous to the operation of the
aircraft, disrupt the wireless telephone network and may be illegal.
Failure to observe these instructions may lead to the suspension or
denial of telephone services to the offender, or legal action, or both.
Emergency calls
IMPORTANT!
This phone, like any wireless phone, operates using radio signals,
wireless and landline networks as well as user- programmed
functions which cannot guarantee connection in all conditions.
Therefore, you should never rely solely upon any wireless phone for
essential communications (e.g. medical emergencies).
Remember, to make or receive any calls the phone must be switched
on and in a service area with adequate signal strength. Emergency
calls may not be possible on all wireless phone networks or when
certain network services and/or phone features are in use. Check
with local service providers.
Making an emergency call
1
If the phone is not on, switch it on.
2
Press and hold the
the phone for calls.
key for several seconds to ready
3
4
Key in the emergency number for your present location
(e.g. 911 or other official emergency number). Emergency
numbers vary by location.
Press Call
75
If certain features are in use (Keyguard, call restrictions, etc.), you may
first need to turn those features off before you can make an emergency
call. Consult this document and your local cellular service provider.
When making an emergency call, remember to give all the necessary
information as accurately as possible. Remember that your wireless
phone may be the only means of communication at the scene of an
accident - do not cut off the call until given permission to do so.
Radio frequency (RF) signals
Your wireless handheld portable telephone is a low power radio
transmitter and receiver. When it is ON, it receives and also sends
out radio frequency (RF) signals.
In August, 1996, the Federal Communications Commission (FCC)
adopted RF exposure guidelines with safety levels for handheld
wireless phones. Those guidelines are consistent with safety standards
previously set by both U.S. and international standards bodies:
ANSI C95.1 (1992)*, NCRP Report 86 (1986)*, ICNIRP (1996)*.
Those standards were based on comprehensive and periodic evaluations
of the relevant scientific literature. For example, over 120 scientists,
engineers, and physicians from universities, government health
agencies and industry reviewed the available body of research to
develop the ANSI Standard (C95.1).
The design of your phone complies with the FCC guidelines (and
those standards).
*American National Standards Institute, National Council on Radiation
Protection and Measurements; International Commission on Non-
Ionizing Radiation Protection.
76
Care and maintenance
Your phone is a product of superior design and craftsmanship and
should be treated with care. The suggestions below will help you to
fulfill any warranty obligations and allow you to enjoy this product
for many years. When using your phone, battery, charger, OR any
accessory:
•
•
•
•
Keep it and all its parts and accessories out of small children’s
reach.
Keep it dry. Precipitation, humidity and liquids contain minerals
that will corrode electronic circuits.
Do not use or store it in dusty, dirty areas as its moving parts can
be damaged.
Do not store it in hot areas. High temperatures can shorten the
life of electronic devices, damage batteries, and warp or melt
certain plastics.
•
Do not store it in cold areas. When the phone warms up (to its
normal operating temperature), moisture can form inside the
phone, which may damage the phone's electronic circuit boards.
•
•
•
Do not attempt to open it. Non-expert handling of the device
may damage it.
Do not drop, knock or shake it. Rough handling can break
internal circuit boards.
Do not use harsh chemicals, cleaning solvents, or strong
detergents to clean it. Wipe it with a soft cloth slightly
dampened in a mild soap-and-water solution.
•
•
Do not paint it. Paint can clog the device’s moving parts and
prevent proper operation.
Use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications or attachments could
damage the phone and may violate regulations governing radio
devices.
•
If the phone, battery, charger, or any accessory is not working
properly, take it to your nearest qualified service facility.
The personnel there will assist you, and if necessary, arrange for
service.
77
17. Technical information
Transmitting power: Up to 600 mW nominal
Operating voltage:
Frequency band:
3.6 V nominal
lowband 824.04 - 848.97 MHz (TX)
869.04 - 893.97 MHz (RX)
highband 1850.04 - 1909.92 MHz (TX)
1930.08 - 1989.96 MHz (RX)
Number of channels: 832 lowband
1997 highband
Number of NAMs
Memory locations:
Memory capacity:
2
100
16 characters per name
32 characters per number
Part No. 9353008
Printed in Canada
09/00
Nokia, Connecting People and the Original Accessories logos are
trademarks of Nokia Corporation and/or its affiliates.
The information contained in this User Guide was written for Nokia
phone NSW-1NX.
The right to make changes and improvements to any of the products
described in this guide without prior notice is reserved.
Phase 5 Issue 2 © 2000 Nokia Mobile Phones. All rights reserved.
US Patent No 5818437 and other pending patents. T9 text input
software Copyright © 1999. Tegic Communications, Inc. All rights
reserved.
These commodities are authorized by the U.S. Government for export
only to Canada, Mexico, or the United States. They may not be
resold, diverted, transferred, or otherwise disposed of in any other
country, either in their original form or after being incorporated
through an intermediate process into other end-items, without the
written approval of the U.S. Department of State.
Para obtener un manual del usuario en español favor de
llamar o enviar un fax al teléfono 1-888-NOKIA2U
(1-888-665-4228), fax 813-249-9619.
For alternate formats of this user guide, call our Customer
Care center at 1-888-665-4228 (NOKIA2U).
78
18. NOKIA One-Year Limited
Warranty
Nokia Mobile Phones, Inc. (“NMP”) warrants that this cellular phone
(“Product”) is free from defects in material and workmanship that
result in Product failure during normal usage, according to the
following terms and conditions:
1. The limited warranty for the Product extends for ONE (1) year
beginning on the date of the purchase of the Product.
2. The limited warranty extends to the original purchaser of the
Product (“Consumer”) and is not assignable or transferable to any
subsequent purchaser/end-user.
3. The limited warranty extends only to Consumers who purchase the
Product in the United States.
4. During the limited warranty period, NMP will repair, or replace, at
NMP's option, any defective parts, or any parts that will not properly
operate for their intended use with new or factory rebuilt replacement
items if such repair or replacement is needed because of product
malfunction or failure during normal usage. No charge will be made to
the Consumer for any such parts. NMP will also pay for the labor
charges incurred by NMP in repairing or replacing the defective parts.
The limited warranty does not cover defects in appearance, cosmetic,
decorative or structural items, including framing, and any non-
operative parts. NMP's limit of liability under the limited warranty
shall be the actual cash value of the Product at the time the Consumer
returns the Product for repair, determined by the price paid by the
Consumer for the Product less a reasonable amount for usage. NMP
shall not be liable for any other losses or damages. These remedies are
the Consumer’s exclusive remedies for breach of warranty.
5. Upon request from NMP, the Consumer must prove the date of the
original purchase of the Product by a dated bill of sale or dated
itemized receipt.
6. The Consumer shall bear the cost of shipping the Product to NMP
in Melbourne, Florida. NMP shall bear the cost of shipping the
Product back to the Consumer after the completion of service under
this limited warranty.
7. The Consumer shall have no coverage or benefits under this
limited warranty if any of the following conditions are applicable:
a) The Product has been subject to abnormal use, abnormal conditions,
improper storage, exposure to moisture or dampness, unauthorized
modifications, unauthorized connections, unauthorized repair, misuse,
neglect, abuse, accident, alteration, improper installation, or other acts
which are not the fault of NMP, including damage caused by shipping.
79
b) The Product has been damaged from external causes such as
collision with an object, or from fire, flooding, sand, dirt, windstorm,
lightning, earthquake or damage from exposure to weather conditions,
an Act of God, or battery leakage, theft, blown fuse, or improper use of
any electrical source, or damage caused by the connection to other
products not recommended for interconnection by NMP.
c) NMP was not advised by the Consumer in writing of the alleged
defect or malfunction of the Product within fourteen (14) days after
the expiration of the applicable limited warranty period.
d) The Product serial number plate or the accessory data code has
been removed, defaced or altered.
e) The defect or damage was caused by the defective function of the
cellular system or by inadequate signal reception by the external
antenna.
8. If a problem develops during the limited warranty period, the
Consumer shall take the following step-by-step procedure:
a) The Consumer shall return the Product to the place of purchase for
repair or replacement processing.
b) If “a” is not convenient because of distance (more than 50 miles)
or for other good cause, the Consumer shall ship the Product prepaid
and insured to:
Nokia Mobile Phones, Inc.
Attn: Repair Department
795 West Nasa Blvd.
Melbourne, FL. 32901
c) The Consumer shall include a return address, daytime phone
number and/or fax number, complete description of the problem,
proof of purchase and service agreement (if applicable). Expenses
related to removing the Product from an installation are not covered
under this limited warranty.
d) The Consumer will be billed for any parts or labor charges not
covered by this limited warranty. The Consumer will be responsible
for any expenses related to reinstallation of the Product.
e) NMP will repair or authorize the repair of the Product under the
limited warranty within 30 days after receipt of the Product by NMP
or an NMP authorized service center. If NMP cannot perform repair
covered under this limited warranty within 30 days, or after a
reasonable number of attempts to repair the same defect, NMP at its
option, will provide a replacement Product or refund the purchase
price of the Product less a reasonable amount for usage.
80
f) If the Product is returned to NMP during the limited warranty
period, but the problem with the Product is not covered under the
terms and conditions of this limited warranty, the Consumer will be
notified and given an estimate of the charges the Consumer must
pay to have the Product repaired, with all shipping charges billed to
the Consumer. If the estimate is refused, the Product will be returned
freight collect. If the Product is returned to NMP after the expiration
of the limited warranty period, NMP's normal service policies shall
apply and the Consumer will be responsible for all shipping charges.
9. The Product consists of newly assembled equipment that may
contain used components that have been reprocessed to allow
machine compliance with Product performance and reliability
specifications.
10. ANY IMPLIED WARRANTY OF MERCHANTABILITY, OR FITNESS
FOR A PARTICULAR PURPOSE OR USE, SHALL BE LIMITED TO THE
DURATION OF THE FOREGOING LIMITED WRITTEN WARRANTY.
OTHERWISE, THE FOREGOING LIMITED WARRANTY IS THE
CONSUMER'S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED. NMP SHALL NOT BE
LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES,
INCLUDING BUT NOT LIMITED TO, LOSS OF ANTICIPATED BENEFITS
OR PROFITS, LOSS OF SAVINGS OR REVENUE, PUNITIVE DAMAGES,
LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT,
COST OF CAPITAL, COST OF ANY SUBSTITUTE EQUIPMENT OR
FACILITIES, DOWNTIME, THE CLAIMS OF ANY THIRD PARTIES,
INCLUDING CUSTOMERS, AND INJURY TO PROPERTY, RESULTING
FROM THE PURCHASE OR USE OF THE PRODUCT OR ARISING FROM
BREACH OF THE WARRANTY, BREACH OF CONTRACT, NEGLIGENCE,
STRICT TORT, OR ANY OTHER LEGAL OR EQUITABLE THEORY, EVEN IF
NMP KNEW OF THE LIKELIHOOD OF SUCH DAMAGES. NMP SHALL
NOT BE LIABLE FOR DELAY IN RENDERING SERVICE UNDER THE
LIMITED WARRANTY, OR LOSS OF USE DURING THE PERIOD THAT THE
PRODUCT IS BEING REPAIRED.
11. Some states do not allow limitation of how long an implied
warranty lasts, so the above one-year warranty limitation may not
apply to you (the Consumer). Some states do not allow the exclusion
or limitation of incidental and consequential damages, so certain of
the above limitations or exclusions may not apply to you (the
Consumer). This limited warranty gives the Consumer specific legal
rights and the Consumer may also have other rights which vary from
state to state.
12. NMP neither assumes nor authorizes any authorized service
center or any other person or entity to assume for it any other
obligation or liability beyond that which is expressly provided for in
this limited warranty including the provider or seller of any extended
warranty or service agreement.
81
13. This is the entire warranty between NMP and the Consumer, and
supersedes all prior and contemporaneous agreements or understandings,
oral or written, and all communications relating to the Product, and
no representation, promise or condition not contained herein shall
modify these terms.
14. This limited warranty allocates the risk of failure of the Product
between the Consumer and NMP. The allocation is recognized by the
Consumer and is reflected in the purchase price of the Product.
15. Any action or lawsuit for breach of warranty must be commenced
within eighteen (18) months following delivery of the Product.
16. Questions concerning this limited warranty may be directed to:
Nokia Customer Care Center, USA
Nokia Mobile Phones, Inc.
7725 Woodland Center Boulevard, Suite #150
Tampa, FL 33614
Telephone: 1-888-NOKIA2U (1-888-665-4228)
Facsimile: (813) 249-9619
TTY Users: 1-800-24NOKIA (1-800-246-6542)
17. The limited warranty period for NMP supplied attachments and
accessories is specifically defined within their own warranty cards
and packaging.
© Nokia is a registered trademark of Nokia Corporation.
82
call forwarding
activating 32
cancelling 32
19. Index
A
call log 41
access codes 62
accessories 66
batteries 68
clearing lists 42
dialed calls 42
missed calls 41
Options key 41
received calls 42
see restricting calls
call timers 42
call waiting 31
answering a waiting call 31
cancelling 31
caller ID 17
showing/hiding number 34
calling card
making calls 35
set-up 19
calls
answering 17
answering automatically
answering with call
waiting 31
ending 30
forwarding 32
initiating a second 30
making 16
silencing an incoming call
chargers 69
covers 66
address
e-mail 51
alarm clock 54
alternate formats of User
Guide 78
answering a call 17
automatic answer 36
antenna 15
external jack 7
automatic answer 36
automatic redial 19
automatic time update 22
confirm first 22
turn off 22
turn on 22
B
batteries 68
attaching 3
charging 3
discharging 4
removing 4
calls
switching between 30
three-way calling 30
care and maintenance 77
chargers 69
business cards 49
receiving 49
sending 49
C
choosing own number 33
clear key 7
calls
83
clearing call lists 42
clock 21
alarm clock 54
automatic time update 22
displaying/hiding 21
setting 21
time format 21
way calling
I
Inbox 46
in-call menu 29
Interactive User Guide 2
K
Keyguard 13
keypad lock
emergency key 9 13
keypad tones 24
keys
covers, changing 66
clear key 7
Navi(TM) key 6
power key 6
scroll keys 6
D
dialed calls 42
downloading ringing tones 55
L
E
language 21
lights 7
editing names/numbers 40
e-mail messages 51
e-mail gateway number 52
forwarding 53
in car kit 22
lock code 62
locking the keypad 13
locking your phone 64
Logic (game) 56
replying 53
saving e-mail addresses 51
sending 52
emergency key 9 28
erasing names/numbers 40
external antenna jack 7
M
making a call 16
calling card 35
prepaid service 61
memory 40
F
Memory (game) 56
menu 8
factory settings, restoring 37
shortcuts 9
message alert tone 24
messages
voice mail 44
missed calls 41
G
game tones 24
games 56
gateway number
e-mail messages 52
H
help text 8
84
deactivating 59
making calls 61
saving access phone
numbers 59
settings
N
NAM selection 33
names
editing 40
erasing 40
saving 38
network feature setting 29
new call 30
numbers
editing 40
entering 12
erasing 40
saving 38
showing/hiding your own
Q
quick alert settings 24
R
reading text messages 45
received calls 42
redial
automatic 19
last number 16
restore factory settings 37
restricting calls 62
ringing option 23
ringing tone 23
downloading 55
ringing volume 24
O
on/off 15
one-touch dialing 33
S
safety information 73
scroll keys 6
P
phone book 38
available memory 40
scrolling view 40
phone lock 64
scrolling view 40
security code 62
security features 62
send own number 34
signal strength 15
silencing an incoming call 18
Snake (game) 56
special characters 12
dialing
start screen 7
system selection 35
NAM selection
power key 6
predictive text input 57
notes about 57
turn off 57
turn on 57
prepaid service 59
activating 59
adding money into
account 60
checking account balance 60
85
T
V
technical information 78
text messages 45
business cards 49
forwarding 48
vibrating alert 24
view own number 33
voice mail messages 44
voice mailbox number 25
voice privacy 26
volume
Inbox 46
predictive text input 57
reading 45
earpiece 16
replying 49
ringing 24
storage 46
writing 47
three-way calling 30
timers 42
W
warning and game tones 24
warranty 79
web
Interactive User Guide 2
User Guide latest version 2
welcome note 26
writing text messages 47
predictive text input 57
tones 23
keypad 24
message alert 24
quick alert settings 24
ringing option 23
ringing tone 23
ringing volume 24
warning and game 24
touch tones 36
saving touch tone strings 37
setting automatic length 37
setting manual length 36
U
unmuting the microphone
86
|