47060 rev2 25/6/07 12:37 Page 1
10/12 cup filter coffee maker
Please read and keep these instructions
Models Covered
47060- Manual Interface
47061- Digital Interface
47062- Manual Interface & Thermal carafe
47063- Digital Interface & Thermal carafe
Getting the best from your new coffee maker...
Warning: Hot water and steam
Safety first
Caution must be used when handling hot water,
coffee or steam.
Run water through your machine before first use
It is important to run water through your coffee maker
in order to rinse the machine. You can also run water
through to warm your coffee machine.
Descale as appropriate for the hardness
of the water in your area
It is important to descale as the performance of your
coffee maker may be impaired by limescale and other
impurities in the water supply.
CM47060 Rev2
For replacement parts, help with using your Morphy Richards product,
problems and lots more, contact us by phone or through our website.
UK Helpline: 0870 060 2610
Replacement parts: 0870 167 6641
Ireland 1800 409119
47060 rev2 25/6/07 12:37 Page 3
Personal safety
Treating scalds
•
•
Ensure the lid of the glass
jug is securely in place
before pouring.
•
•
Run cold water over the
affected area immediately.
Do not stop to remove
clothing, get medical help
quickly.
Take care to pour hot
coffee slowly and carefully
without tipping the glass
jug too fast.
Choice of coffee
Choose a finely ground
espresso coffee to use with
this machine.
•
Do not fill above the
capacity mark of the water
level gauge marked on the
jug.
NOTE: Avoid blends that
are very powdery. When
the coffee is too finely
ground it may block the
filter.
•
•
Do not use the glass jug in
a microwave.
Milk should not be
reheated, only heat it when
required.
ELECTRICAL
•
When heating milk, please
use the stainless steel jug
provided.
REQUIREMENTS
Check that the voltage on
the rating plate of your
appliance corresponds
with your house electricity
supply which must be A.C.
(Alternating Current).
•
•
•
Do not fill the milk jug
above the MAX mark.
Do not touch metal parts
until the unit has cooled.
If the socket outlets in your
home are not suitable for
the plug supplied with this
appliance the plug should
be removed and the
This appliance is not
intended for use by
persons (including children)
with reduced physical,
sensory or mental
appropriate one fitted.
capabilities, or lack of
experience and knowledge,
unless they have been
given supervision or
instruction concerning use
of the appliance by a
person responsible for their
safety.
WARNING: The plug
removed from the
mains lead, if severed,
must be destroyed as a
plug with a bared
flexible cord is
hazardous if engaged
into a live socket
outlet.
Children
Should the fuse in the 13
amp plug require changing,
a 13 amp BS1362 fuse
must be fitted.
•
•
Children do not understand
the dangers associated
with operating electrical
appliances. Never allow
children to use this
WARNING: This
appliance must be
earthed.
appliance.
Children should be
supervised to ensure that
they do not play with the
appliance.
3
2
UK Helpline 0870 060 2610 Replacement Parts 0870 167 6641 Ireland Helpline 1800 409119
47060 rev2 25/6/07 12:37 Page 4
Product features
Á
⁄
¤
›
Ë
‹
fi
‰
Â
È
Í
Í
‚
/„
‡
/·
fl
fl
Ê
Î
· 8/10 cups steel thermal
Ë Plug storage
È Anti drip
Features
coffee jug
⁄ Measuring spoon storage
area
‚ Manual interface (see
overleaf)
Í Lid release
Î Hot plates
¤ Water re-fill point
„ Digital interface (see
‹ Measuring spoon
overleaf)
› Filter holder and
‰ Frother control
permanent mesh filter
 Milk hot plate switch
fi Lid opening push button
Ê Illuminated water level
fl Milk frother steel jug
indicator
‡ 12/15 cups glass coffee
Á Coffee strength control
jug
3
4
47060 rev2 25/6/07 12:37 Page 5
Ì
Ó
Ï
Ô
ÚÒ
‚ Manual interface version
Auto keep warm indicator
Ò Milk frother device ON indicator
Ú Milk hot plate ON indicator
Ï Function selector
Ì
1
/2 carafe indicator
Ó 1 carafe indicator
Ô Brewing ON indicator
Û
ı
Ù
˘
35
36
˜
Ú
Ò
ˆ
◊
¯
34
„ Digital interface version
Auto keep warm indicator
Ò Milk frother device ON indicator
Ú Milk hot plate ON indicator
ˆ Hour function push button
˜ Minute function push button
¯ Cup selector push button
˘ Quality and brew indicator
◊ Programming mode indicator
Û Power ON/OFF selection push
button
34
Automatic timer function
indicator
Ù Programme selection push
button
Cup selection indicator
24 hour clock
35
36
ı Auto function push button
Milk hot plate ON pilot light
Milk frother device ON pilot light
Milk frother device off pilot light
Auto keep warm light
1
/2 carafe light
Power ON/OFF
1 carafe light auto
4
5
UK Helpline 0870 060 2610 Replacement Parts 0870 167 6641 Ireland Helpline 1800 409119
47060 rev2 25/6/07 12:37 Page 6
A
OPERATING THE
APPLIANCE
MANUAL INTERFACE
‚
VERSIONS
BEFORE USE
Making coffee
Before using your coffee maker
for the first time or if you have
not used it for some time, rinse
the machine by running water
through. Follow the procedure
for making coffee, without coffee
in the filter holder.
1
2
Press the push button fi to
open the hinged lid. The lid will
automatically rise.
Using a jug, fill the water
reservoir ¤ with the required
amount of water using the level
indicator Ê as a guide. Both the
jug and water level indicator are
marked in cups A.
B
The product that you have
purchased is available in four
different versions:
3
Spoon ‹ the required amount
of ground filter coffee into the
mesh filter › spreading evenly.
We suggest one level measuring
spoon for every cup. Ensure the
filter is sitting properly in the
filter holder B.
•
•
•
Manual version - Glass carafe
Manual version -Thermal carafe
24 hour automatic timer version
- Glass carafe
•
24 hour automatic timer version
-Thermal carafe
4
5
Close the lid. Ensure the lid is
closed and latched properly C,
otherwise the machine will not
function correctly.
C
For the complete understanding
of how to use your machine
please refer to the specific
Slide the jug ‡/· into the
coffee maker ensuring it sits
correctly on the hot plate D.
The jug lid must be in place
during the brewing process;
otherwise the non drip valve will
not open, causing the filter to
flood.
section related to your version.
Please note not all variants are
available in all countries, please
contact your retailer for more
information.
D
5
6
47060 rev2 25/6/07 12:37 Page 7
E
•
Thermal Carafe Variant
We suggest consuming your
coffee within two hours, after
this time we suggest brewing
another jug of fresh coffee.
Note:Thermal carafe versions
have no hot plate. Please ensure
the jug sits correctly on the base
recess.
WARNING: The coffee maker
and hot plates are hot and
remain hot for some time
after switching off.
•
Ensure the jug · lid is fully
closed by turning the lid
clockwise, this ensures the
maximum temperature is
maintained in the jug. To ensure
the coffee is kept as warm as
possible we advise you rinse
your thermal carafe in hot water
before use.
NOTE:
F
•
Remember to turn off the
machine when you have
finished.
•
•
Allow the unit to cool.
•
Please note the jug lid must be
in place during the brewing
process; otherwise the non-drip
valve will not open, causing the
filter to flood.
Remove the permanent filter and
empty the used coffee grounds.
Wash the filter immediately and
dry thoroughly.
6
7
Select the required strength of
coffee using the strength
selector on the lid E.
•
Thermal Carafe Variants
•
When the brewing process is
complete the product remains
on, we recommend you switch
off your coffee maker as soon as
brewing is complete.
Plug the filter coffee maker in at
the wall socket and switch on,
the water gauge Ê will
illuminate. Rotate the dial Ï to
select one of the two on
•
•
The thermal carafe · will keep
the coffee warm in the jug for up
to four hours.
positions available: 1/2 carafe or a
full carafe,F depending on the
number of cups required. Refer
to ‘Cup selection function’ page
11 for further information.
The anti drip valve È will
prevent any remaining coffee
dripping onto the base recess
during serving.
8
•
The cup selection indicator
Ì/Ó and the brewing on
indicator Ô will light up. The hot
water will start to flow through
the coffee grounds and into the
jug as coffee for you to enjoy.
•
We suggest consuming your
coffee within two hours, after
this time we suggest brewing
another jug of fresh coffee.
Glass Carafe Variant
•
WARNING: The coffee maker
and hot plates are hot and
remain hot for some time
after switching off.
When the brewing process is
complete the product will
automatically switch to keep
warm; the auto keep warm
indicator will light up.
NOTE:
•
Remember to turn off the
machine when you have
finished.
The automatic keep warm
function will keep the coffee
warm in the carafe until the
product is switched off.
•
•
Allow the unit to cool.
The anti-drip valve È will
prevent any remaining coffee
dripping onto the hot plate
during serving. Ensure that the
jug is replaced on the hot plate
after serving.
Remove the permanent filter and
empty the used coffee grounds.
Wash the filter immediately and
dry thoroughly.
6
7
UK Helpline 0870 060 2610 Replacement Parts 0870 167 6641 Ireland Helpline 1800 409119
UK Helpine 0870 060 2614 Repacement Parts 0870 157 6645 Ireland Helpine 1800 409119
47060 rev2 25/6/07 12:37 Page 8
G
H
DIGITAL INTERFACE
•
Thermal Carafe Variant
„
VERSIONS
Note:Thermal carafe versions
have no hot plate. Please
ensure the jug sits correctly on
the base recess.
Set the clock
When the machine is plugged
in, the display will flash 12:00
dimly.
•
•
•
Ensure the jug · lid is fully
closed by turning the lid
clockwise, this ensures the
maximum temperature is
maintained in the jug. To ensure
the coffee is kept as warm as
possible we advise you rinse
your thermal carafe in hot water
before use.
To set the time press the hour
button ˆ and minute buttons
˜ to reach the desired time.
NOTE:The clock is a 24 hour
clock.
The clock will be reset, each
time the product is unplugged
at the wall.
•
Please note the jug lid must be
in place during the brewing
process; otherwise the non-drip
valve will not open, causing the
filter to flood.
I
Making coffee
1
2
Press the push button fi to
open the hinged lid. The lid will
automatically rise G.
6
7
Select the required strength of
coffee using the strength
selector on the lid L.
J
Using the jug, fill the water
reservoir ¤ with the required
amount of water using the level
indicator Ê as a guide. Both
the jug and water level indicator
are marked in cups H.
Press the power ON/OFF
selection button Û. The display
lights up brightly and the cup
selection indicator will flash 35
showing the previous selection.
NOTE: If the machine has been
unplugged from the wall socket
since the last operation the
previous selection will be
cleared, the default setting will
be applied (1 full carafe).
3
Spoon ‹ the required amount
of ground filter coffee into the
mesh filter › spreading evenly.
We suggest one level measuring
spoon for every cup. Ensure the
filter is sitting properly in the
filter holder I.
K
8
Press the cup selection button
¯ to select one of the available
options, 1/2 carafe or full carafe
M depending on the number of
cups required. Refer to ‘Cup
selection function’ page 11 for
further information. The
selection indicator will stop
flashing, if no buttons are
pressed for 2 seconds the
machine will begin the brewing
process.
4
5
Close the lid. Ensure the lid is
closed and latched properly,J
otherwise the machine will not
function correctly.
L
Slide the jug ‡/· into the
coffee maker ensuring it sits
correctly on the hot plate K.
The jug lid must be in place
during the brewing process;
otherwise the non drip valve will
not open, causing the filter to
flood.
9
The brewing indicator ˘ will
start to illuminate from left to
right indicating that brewing is in
progress, hot water will start to
flow through the coffee grounds
and into the jug as coffee ·.
M
7
47060 rev2 25/6/07 12:37 Page 9
•
Glass Carafe Variant
•
Thermal Carafe Variant
When the brewing process is
complete the product will
When the brewing process is
complete the product remains
on, the brewing indicator ˘ will
stop illuminating from left to
right, all segments will remain
solidly illuminated, the indicator
has now changed from a
automatically switch to keep
warm ; the brewing indicator
˘ will stop illuminating from left
to right. All segments will remain
solidly illuminated indicating the
machine is in keep warm state.
The indicator has now changed
from a brewing indicator to a
quality indicator. Refer to ‘Coffee
Quality indicator’ page 11 for
further information.
brewing indicator to a quality
indicator. Refer to ‘Coffee
Quality indicator’ page 11 for
further information.
If the coffee is to be consumed
immediately we recommend
switching off your coffee maker
as soon as brewing is complete.
The automatic keep warm
function will keep the coffee
warm in the carafe until the
product is switched off.
NOTE: If you switch off your
coffee maker the coffee quality
indicator will turn off and reset.
For safety reasons the coffee
maker will automatically switch
off after two hours.
The thermal carafe will keep the
coffee warm in the jug for up to
four hours.
The anti-drip valve È will
prevent any remaining coffee
dripping onto the hot plate
during serving. Ensure that the
jug is replaced on the hot plate
after serving.
For safety reasons the coffee
maker will automatically switch
off after two hours.
The anti drip valve will prevent
any remaining coffee dripping
onto the base recess during
serving.
We suggest consuming your
coffee within two hours, after
this time we suggest brewing
another jug of fresh coffee.
We suggest consuming your
coffee within two hours, after
this time we suggest brewing
another jug of fresh coffee.
WARNING: The coffee
maker and hot plates are
hot and remain hot for some
time after switching off.
WARNING: The coffee
NOTE:
maker and hot plates are
hot and remain hot for some
time after switching off.
•
Remember to turn off the
machine when you have
finished.
NOTE:
•
•
Allow the unit to cool.
•
Remember to turn off the
machine when you have
finished.
Remove the permanent filter and
empty the used coffee grounds.
Wash the filter immediately and
dry thoroughly.
•
•
Allow the unit to cool.
Remove the permanent filter and
empty the used coffee grounds.
Wash the filter immediately and
thoroughly.
UK Helpline 0870 060 2610 Replacement Parts 0870 167 6641 Ireland Helpline 1800 409119
9
8
47060 rev2 25/6/07 12:37 Page 10
Set the automatic
timer function
If setting the automatic timer
function during the brewing
process, wait until the process is
complete before pressing the
AUTO button.
NOTE:The timer function can be
set when the coffee maker is
brewing or when it is in standby.
6
7
Press the AUTO button ı again
to cancel the automatic function,
the timer function indicator will
disappear. The machine will keep
in the memory the cup selection
setting and the start time until it
is unplugged from the mains
socket.
1
Press the programme button Ù.
The display will change to show
the previous set time and cup
selection flashing. If no previous
setting has been made or the
machine has been unplugged
from the socket since the last
setting the default setting will be
shown; 12:00 and full carafe.
To change the start time and the
number of cups repeat steps
1-5.
2
3
Select ¯ the desired number of
cups that want to be brewed, 1/2
or full carafe (see cup selection
function on page 11). The cup
selector indicator will stop
flashing.
WARNING: Remember to fill
the water tank with water
and the filter with coffee
before activating the auto
function.
Press the hour and minute ˜
buttons to set the desired time.
The start time will stop flashing.
NOTE:The clock is a 24 hour
clock.
NOTE:The programming mode
indicator continues to flash to
show the display is still in
programming mode.
If no buttons are pressed, the
display will revert to the time
display within 5 seconds.
4
If the programme button Ù is
pressed again or if no buttons
are pressed within 5 seconds
the cup selection setting and the
start time are memorised.
5
To activate the automatic timer
function press AUTO button ı.
•
The display will change to show
the programmed time and cup
selection setting for 5 seconds.
The display will then change to
show the time, the automatic
timer function indicator will
illuminate to show the automatic
timer function is set.
•
With the automatic function
activated the coffee maker will
turn on at the desired time and
start to brew the coffee.
NOTE: If the AUTO button ı is
pressed during the brewing
process the machine will switch
off and the automatic timer
function will be activated.
9
47060 rev2 25/6/07 12:37 Page 11
N
Frothing milk
Pour the coffee into the cups
and then gently pour or
preferably spoon the milk onto
the coffee.
It is advised to start heating your
milk ready for frothing when you
start making the coffee. This
helps to ensure the milk reaches
its optimum frothing
WARNING: The stainless
steel jug and the hotplate
will remain hot for
sometime after switching
the machine off.
temperature.
1
2
Fill the stainless steel jug fl with
the required amount of milk. Do
not exceed the maximum level.
O
NOTE:The milk frother jug and
lid can be disassembled for easy
cleaning.
Place the jug on the hot plate Î
N and push the frother hot
plate  ON/OFF switch to the
‘ON’ O position, the hot plate
indicator will light up.
It is recommended that you
disassemble and clean the milk
frother jug and its components
immediately after use, as dried
milk can be difficult to remove.
3
4
Once the coffee is brewed (and
the auto keep warm indicator
lights up) the milk is ready to
froth.
NOTE: All milk jug and coffee jug
components are dishwasher
safe for easy cleaning.
P
Engage the frother system by
turning the frother control lever
P ‰ to the right, the motor will
start automatically and the milk
frother device ON indicator will
illuminate Ò.
Frothing should take between
30-60 seconds.
NOTE: Frothing time can vary
depending on the type of milk
used and its starting
temperature. We recommend to
use semi skimmed milk from the
fridge.
Q
5
Disengage the frother system
from the jug by turning the
frother control lever to the left Q
‰, the motor will stop
automatically. Push and release
the milk hot plate switch to turn
off the hot plate Â.
WARNING: Take care the
milk will be very hot.
Remove the milk jug fl from the
hot plate and press the lid
release button Í to disengage
the lid. The lid assembly can be
removed for easy pouring and
spooning off the milk.
NOTE:The lid can be turned
upside down and rest on the
work surface. The inner lid is
shaped to collect any dripping
milk and froth for minimal mess.
10
UK Helpline 0870 060 2610 Replacement Parts 0870 167 6641 Ireland Helpline 1800 409119
47060 rev2 25/6/07 12:37 Page 12
Cup selection
function
Coffee quality
indicator
1
This machine has a special
selector that maintains the
quality of coffee brewed in
relation to the number of cups
selected.
The coffee quality indicator will
show the quality of the coffee in
the carafe in relation to the time
since brewing was completed.
Quality of the coffee is a
personal choice. The quality
indicator gives an indication of
the quality and taste of coffee
after the brewing process is
complete.
There are two options available:
1
•
•
/2 carafe (1-6 cups - Glass jug)
(1-5 cups -Thermal jug)
It is not absolute and can differ
due to personal taste, or type of
coffee used.
1 carafe (7-12 cups - Glass jug)
(6-10 cups -Thermal
jug)
The graph shown below gives
an indication of the relation
between each segment of the
display in relation to both quality
and time.
2
3
The selection needs to be set in
relation to the amount of water
in the water tank and the
amount of coffee powder in the
filter.
B
C
D
The incorrect selection of this
function will not affect the
functionality of the machine
however the quality and taste of
the coffee brewed will be
affected.
A
E
4
If you find the strength selector
does not provide a weak or
strong enough cup of coffee to
suit your taste, the cup selection
function can be used in
conjunction to achieve a
stronger or weaker cup of
coffee.
•
The table below shows the
settings to use in relation to the
volume of water in the tank to
help achieve a stronger or
weaker coffee. Feel free to
experiment with different
settings until you achieve the
desired strength of coffee to suit
your own personal taste.
1-6
1-5
7-12
6-10
1/2
1
Standard
Stronger
Weaker
Standard
11
47060 rev2 25/6/07 12:37 Page 13
RECIPES
Cafe Latte
1/2 espresso
5
Pour the coffee, hot milk
and hot chocolate into a tall
glass and serve.
Cappuccino
1/3 espresso
1/2 hot frothed milk
Irish Coffee
Makes 2 servings
1/3 hot milk
1
2
Prepare coffee as per
‘making a coffee’
1/3 hot frothed milk
instructions (5, 6 or 7).
40ml of double cream
2 tsp sugar
Chocolate powder for
sprinkling
Fill the stainless steel milk
jug with the required
1
2
Prepare coffee as per
‘making a coffee’
instructions (Page 5, 6 or
7).
amount of milk, place on
the hotplate and switch on.
The milk will take approx. 7
minutes to reach the
4 shot measurements of
Irish whisky
350ml hot strong coffee
appropriate temperature.
Fill the stainless steel milk
jug with the required
1
2
Whip double cream until
thick then chill.
3
Froth milk by lifting the milk
jug up to the milk frothing
blade ensuring that the
blade is just under the
surface of the milk and
press the milk frothing
button. The milk will take
approx. 30-60 seconds to
froth.
amount of milk, place on
the hotplate and switch on.
The milk will take approx. 7
minutes to reach the
Warm 2 Irish coffee glasses
with hot water and place in
each a teaspoon of sugar
and 2 shots of Irish whisky
in glass.
appropriate temperature.
3
Froth milk by lifting the milk
jug up to the milk frothing
blade ensuring that the
blade is just under the
surface of the milk and
press the milk frothing
button. The milk will take
approx. 30 seconds to
froth.
3
4
Divide coffee among the
glasses.
4
Pour the coffee into a tall
glass and top with the
frothed milk.
Slowly dribble the chilled
cream over the back of the
spoon onto the top of the
coffee.
Moccacino
1/3 espresso
5
Do not stir.
4
5
Pour the coffee in first and
then the hot milk into a
cappuccino cup, spoon
over frothed milk.
1/3 hot frothed milk
1/3 hot chocolate
Sprinkle with chocolate
powder to serve.
1
2
Prepare coffee as per
‘making a coffee’
instructions (5, 6 or 7).
Amaretto Coffee
Fill the stainless steel milk
jug with the required
250ml hot strong coffee
amount of milk, place on
the hotplate and switch on.
The milk will take approx. 7
minutes to reach the
2 tablespoons of double or
whipped cream
2 shots of Amaretto
Sugar to taste
appropriate temperature.
3
4
Froth milk by lifting the milk
jug up to the milk frothing
blade ensuring that the
blade is just under the
surface of the milk and
press the milk frothing
button. The milk will take
approx. 30 seconds to
froth.
1
2
Stir the coffee and alcohol
together either with 2
tablespoons of double-
cream, or top with a dollop
of whipped cream.
Sprinkle with grated
chocolate and serve.
Prepare the hot chocolate
according to the
manufacturer’s instructions.
12
UK Helpline 0870 060 2610 Replacement Parts 0870 167 6641 Ireland Helpline 1800 409119
47060 rev2 25/6/07 12:37 Page 14
CLEANING AND
Cleaning care
MAINTENANCE
1
2
3
Unplug the coffee maker, and
allow to cool.
Refilling
Switch off the coffee maker, and
allow 5 minutes to cool.
Do not immerse the coffee
maker in liquid.
1
2
Rinse the water tank
Lift the lid and refill with cold
water.
occasionally with cold water. Do
not use a cloth as any residue or
lint left behind may clog the
coffee maker.
Descaling
4
5
Remove the permanent filter ›
and filter holder discard the
used coffee and wash with
warm soapy water. Extended
soaking is recommended at the
same time as descaling. Rinse
and dry thoroughly.
•
If you live in a harder water area,
we recommend that your coffee
maker is descaled at regular
intervals, eg. every 2 - 3 months.
In areas of moderately hard
water you should descale every
6 months.
Wash the coffee jug and milk jug
including all frothing
components, in warm soapy
water. Rinse and dry all parts
thoroughly.
•
•
If the water filters through more
slowly than usual, it is a sign
that descaling is necessary.
We recommend you to use
proprietary liquid descaler which
is especially made for coffee
makers and plastic kettles.
Follow the instructions on the
bottle or sachet, and then
operate the coffee maker with
just water 3 times before making
coffee.
NOTE: Coffee jug, milk jug and
frother parts are all dishwasher
safe.
6
Wipe all external surfaces with a
damp cloth and dry thoroughly.
•
Care must be taken to ensure
the non drip valve situated on
the bottom of the filter holder is
not damaged during cleaning.
•
Do not use kettle descaler
unless the packet specifically
states it is suitable for coffee
makers.
•
Never use harsh or abrasive
cleaners.
NOTE:The permanent mesh
filter should not be in place
during descaling.
13
47060 rev2 25/6/07 12:37 Page 15
Helpline
If you have any difficulty with
your appliance, do not hesitate
to call. We are more likely to be
able to help than the store from
where you bought it.
Please have the following
information ready to enable our
staff to deal with your enquiry
quickly:
•
•
Name of the product.
Model number as shown on the
underside of the appliance.
•
Serial number as shown on
underside of the appliance.
For electrical products sold
within the European
Community:
•
At the electrical products useful
life it should not be disposed of
with household waste.
•
•
Please recycle where facilities
exist.
Check with your Local Authority
or retailer for recycling advice in
your country.
UK Helpline
0870 060 2610
0870 167 6641
1800 409119
Replacement Parts
Ireland Helpline
UK Helpline 0870 060 2614 Replacement Parts 0870 157 6645 Ireland Helpline 1800 409119
14
47060 rev2 25/6/07 12:37 Page 16
YOUR TWO YEAR
EXCLUSIONS
GUARANTEE
Morphy Richards shall not be liable
to replace or repair the goods under
the terms of the guarantee where:
It is important to retain the retailers
receipt as proof of purchase. Staple
your receipt to this back cover for
future reference.
1
The fault has been caused or is
attributable to accidental use,
misuse, negligent use or used
contrary to the manufacturers
recommendations or where the fault
has been caused by power surges or
damage caused in transit.
Please quote the following
information if the product develops a
fault. These numbers can be found
on the base of the product.
Model no.
Serial no.
2
3
4
5
6
•
The appliance has been used on a
voltage supply other than that
stamped on the products.
All Morphy Richards products are
individually tested before leaving the
factory. In the unlikely event of any
appliance proving to be faulty within
28 days of purchase it should be
returned to the place of purchase for
it to be replaced.
Repairs have been attempted by
persons other than our service staff
(or authorised dealer).
Where the appliance has been used
for hire purposes or non domestic
use.
If the fault develops after 28 days
and within 24 months of original
purchase, you should contact the
Helpline number quoting Model
number and Serial number on the
product, or write to Morphy Richards
at the address shown.
Morphy Richards are not liable to
carry out any type of servicing work,
under the guarantee.
Plastic filters for all Morphy Richards
kettles and coffee makers are not
covered by the guarantee.
You may be asked to return a copy
of proof of purchase
This guarantee does not confer any
rights other than those expressly set
out above and does not cover any
claims for consequential loss or
damage. This guarantee is offered as
an additional benefit and does not
affect your statutory rights as a
consumer.
Subject to the exclusions set out
below (see Exclusions) the faulty
appliance will then be repaired or
replaced and dispatched usually
within 7 working days of receipt.If for
any reason this item is replaced
during the 2 year guarantee period,
the guarantee on the new item will
be calculated from original purchase
date. Therefore it is vital to retain
your original till receipt or invoice to
indicate the date of initial purchase.
•
This guarantee is valid in the UK and
Ireland only.
For electrical products sold
within the European
Community. At the end of
the electrical products
useful life it should not be
disposed of with household
waste.
Please recycle where
facilities exist. Check with
your Local Authority or
retailer for recycling advice
in your country.
To qualify for the 2 year guarantee
the appliance must have been used
according to the manufacturers
instructions. For example coffee
makers should have been regularly
descaled.
The After Sales Division
Morphy Richards Ltd
Mexborough, SouthYorkshire,
England, S64 8AJ
Morphy Richards products are intended for household use only.
Registration 644702
Morphy Richards has a policy of continuous improvement in product quality and
design. The company, therefore reserves the right to change the specification of its
models at any time.
Helpline (office hours)
UK 0870 060 2610
Republic of Ireland 1800 409119
47060 MUK Rev2 06/07
For details of other products in the Morphy Richards range please see our website . . .
|