PERSONAL CD, CD-R/RW PLAYER
with 40 SECOND ELECTRONIC
ANTI-SKIP PROTECTION,
and FM DIGITAL TUNER
OWNER’S MANUAL
HD8110
HD8110_052404.p65
22
25/5/2004, 12:21
IMPORTANT NOTES
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
Avoid installing the unit in locations described below:
• Places exposed to direct sunlight or • Dusty places.
close to heat radiating appliances such • Places subject to constant
as electric heaters.
vibration.
• Humid or moist places.
CLASS 1 LASER PRODUCT
CAUTION
CLASS 1 LASER PRODUCT
APPAREIL Á LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
INVISIBLE LASER RADIATION
WHEN OPENAND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM
This product contains a low power Laser Device.
CAUTION
THIS LASER COMPACT DISC PLAYER FUNCTIONS BY HELP OF INVISIBLE
LASER LIGHT AND IS EQUIPPED WITH SAFETY SWITCHES TO AVOID
EXPOSURE WHEN DOOR IS OPEN AND SAFETY INTERLOCKS ARE
DEFEATED. IT IS DANGEROUS TODEFEAT OR BYPASS SAFETY SWITCHES.
DANGEROUS VOLTAGE
Uninsulated Dangerous Voltage, that may be of sufficient
magnitude to constitute a risk of electric shock to persons is
present within this product's enclosure.
ATTENTION
The Owner's Manual contains important operating and
maintenance instructions.
For your safety, it is necessary to refer to the manual.
This device complies with part 15 of the FCC rules. Operation is subject to the
condition that this device does not cause harmful interference.
2
HD8110_052404.p65
2
25/5/2004, 12:21
PREPARATION FOR USE
REMOVE THE TRANSIT CARD
This personal CD player is shipped with a dummy CD ‘transit card’ inside the CD
compartment. The purpose of this card is to prevent the laser from moving during
shipment of the product. This card must be removed before using the CD player.
Slide the OPEN switch to the right to unlock the CD door. Remove the ‘transit card’
from the player and discard it.
POWER SOURCES
This personal CD player is designed to operate on two “AA” batteries, not included.
Use a well known brand of alkaline batteries for longest life and best performance.
This player can also be operated by an optional AC/DC converter/adapter, not
included. If you decide to purchase an optional AC/DC adapter the specification
must be as follows:
Input: 120V 60Hz AC
Output: 4.5V DC, 500 mA.
Plug: 1.7 mm Female Type with Positive Center, UL Listed.
Negative (–)
Positive (+)
You may also purchase a “Universal” type AC/DC adapter which allows you to
select the required output voltage and plug polarity, and normally includes multiple
plug sizes to fit most brands of equipment. Always look for the “UL” listing mark
when you purchase an adapter.
3
HD8110_052404.p65
3
25/5/2004, 12:21
INSTALLING THE BATTERIES
Note: The battery compartment is located inside the CD compartment.
1.) Slide the OPEN switch to the right to open the CD door. If you have not already
done so, remove the dummy CD ‘transit card’ and discard it.
2.) Press down on the “Arrow” mark in the center of the battery door and slide the
door outward as shown until the door ‘pops’ open.
3.) Insert two alkaline “AA” batteries in the battery compartment. Be sure to observe
the polarity markings engraved in the battery compartment. If the batteries are
inserted incorrectly the unit will not work.
4.) Fold the battery removal ribbon over the top of the batteries, close the battery
door, and slide the door inward into it is fully locked again.
5.) Close the CD door.
REPLACING THE BATTERIES
When the battery symbol
flashes in the display the batteries are becoming
weak and should be replaced. Always replace both batteries at the same time with
new fresh alkaline batteries. Do not mix old and new batteries or different types of
batteries together.
If the display remains blank when you press the PLAY/PAUSE button, the batteries
are completely dead. Replace them immediately. If dead batteries are left inside
the battery compartment for a long period of time they may leak and cause damage
to the unit, and such damage or corrosion from leaking batteries is not covered by
your warranty.
4
HD8110_052404.p65
4
25/5/2004, 12:21
CONNECTING THE OPTIONAL AC ADAPTER (NOT INCLUDED)
1.) Connect the small female plug of the optional AC adapter to the “DC IN 4.5 V”
jack on the right side of the CD player.
2.) Connect the adapter housing to your 120V AC 60Hz outlet.
DC 4.5V INPUT JACK
SKIP FWD./
TUN. UP
PLAY/
PAUSE
PRESET MODE
RADIO
STOP
SKIP REV./
TUN. DOWN
TO 120V/60Hz AC OUTLET
OPTIONAL AC/DC ADAPTER
Notes:
• Never connect or disconnect the adapter from the AC outlet while your hands
are wet.
• The housing of the AC adapter may become warm during operation. This is
normal.
• The female plug of the AC adapter must be completely disconnected from the
CD player in order to operate the player on batteries.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery
compartment. Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture
(Follow battery manufacturer’s directions.)
5
HD8110_052404.p65
5
25/5/2004, 12:21
CONNECTING THE STEREO HEADPHONES
Connect the plug of the supplied stereo headphones to the green-colored PHONES
jack on the left side of the cabinet.
NOTE: Make sure the headphone plug is inserted into the PHONES jack as
far as it will go. If the plug is not fully inserted, you may only hear sound from
one side of the headphones.
SKIP FWD./
TUN. UP
PLAY/
PAUSE
PRESET MODE
MEMORY RADIO
STOP
SKIP REV./
TUN. DOWN
IMPORTANT!
Always set the VOLUME control to a low level before you put the headphones on
and begin playing a CD. Then start playback and gradually increase the volume to
a comfortable listening level. Do not play the CD at loud volume levels that might
prevent you from hearing warning sounds such as car horns, etc.
6
HD8110_052404.p65
6
25/5/2004, 12:21
LOCATION OF CONTROLS AND INDICATORS
9
10
8
11
7
6
SKIP FWD./
TUN. UP
12
13
PLAY/
PAUSE
PRESET
MEMORY RADIO
MODE
5
4
STOP
SKIP REV./
TUN. DOWN
14
15
3
2
16
1
7
HD8110_052404.p65
7
25/5/2004, 12:21
1.) OPEN
Switch – Slide to the right to unlock and open the CD door.
2.) VOLUME Control – Raises or lowers the volume.
3.) PHONES Jack – Connect stereo headphones, included, to this jack.
4.) HOLD Switch.
5.) MEMORY Button.
6.) PRESET Button.
7.) MODE Button.
CD - Selects the playback mode: Repeat 1/All, Shuffle, or Intro.
FM Radio - Select FM STEREO/MONO.
8.) RADIO Button.
9.) LCD Display – Shows Track number, Playing time, Anti-Skip status,
Program, Repeat, Shuffle, and Intro modes.
10.) PLAY/PAUSE Button.
11.) SKIP FWD./TUN. UP Button.
12.) DC IN 4.5V Input Jack – Connect an AC adapter (not included) to this
jack to use 120V 60Hz house current.
13.) SKIP REV./TUN. DOWN Button.
14.) STOP Button.
15.) CD Door.
16.) Battery Compartment (Inside CD Compartment).
8
HD8110_052404.p65
8
25/5/2004, 12:21
LCD DISPLAY INDICATORS
3
4
5
6
7
2
1
8
9
10
11
12
1.) FM Radio Indicator.
2.) FM STEREO Indicator.
3.) PROG (Program) Indicator – Appears when programming tracks / FM
preset stations, or playing programmed tracks.
4.) INTRO Indicator – Appears when Intro playback mode is selected.
5.) SHUFF (Shuffle) Indicator – Appears when Random playback mode
is selected.
6.) REPEAT 1/ALL Indicators – Appears when the Repeat playback mode
is selected.
7.) Battery Status Indicator – Flashes when battery level becomes low.
8.) FM MONO Indicator.
9.) HOLD Indicator – Appears when HOLD switch is set to ‘On’ position.
10.) Anti-Shock Bar Indicator – Indicates ESP Protection is activated.
11.) CD Elapsed Time / FM Frequency Display.
12.) CD Track Number / FM preset station number indicator.
9
HD8110_052404.p65
9
25/5/2004, 12:21
OPERATING INSTRUCTIONS
SPECIAL FUNCTIONS
HOLD Switch
The HOLD switch (on the left side cabinet) must be in the ‘Off’ (left) position to
start the CD player. If you plan to carry the CD player in a handbag, briefcase,
school bag, back pack, etc, slide the HOLD switch to the ‘On’ (right) position.
While the HOLD switch is ‘On’ all of the controls on the CD door are disabled. This
prevents the player from starting accidentally by something pressing against the
PLAY/PAUSE or RADIO button.
(On)
(Off)
After you begin CD playback you may also slide the HOLD switch to the ‘On’ (right)
position to disable all the controls on the CD door. You can then place the player in
a handbag, backpack, etc, and do not have to worry that the player will be
accidentally turned off by something pressing against the STOP button or Track
Skip buttons.
10
HD8110_052404.p65
10
25/5/2004, 12:21
Electronic Skip Protection (ESP)
This CD player includes an Electronic Skip Protection circuit that continuously
stores 40 seconds of CD music in an electronic memory. If the player is bumped
or shaken you will not hear any skipping because the player is reading from the
memory, not directly from the disc. Of course if the shaking continues for more
than 40 seconds, the ESP memory will be depleted and the player may then skip
or stop if the shaking continues.
ESP memory function is automatically activated during CD playback. The display
will show the ESP meter
and begin to fill up with bars.
Each bar represents approximately 8 seconds of music in the memory. When all 5
bars appear the memory contains 40 seconds of music.
If the player is bumped or shaken one or more of the bars may disappear as the
memory is depleted
.
When the shaking stops the memory will fill up
again.
11
HD8110_052404.p65
11
25/5/2004, 12:21
NORMAL CD PLAYBACK
• Make sure you have installed the batteries.
• Make sure the HOLD switch is set to the ‘Off’ (left) position.
• Make sure to set the VOLUME control to a low setting before you put on
the headphones.
IMPORTANT:
This CD player can play normal CDs plus CD Recordable (CD-R) and CD
Rewriteable (CD-RW) discs. However the playability of CD-R/RW discs may be
affected by the type of software that was used in ‘ripping’ the tracks from the
original discs and ‘burning’ the tracks onto the blank media. Playability may also
be affected by the quality and condition of the blank media you use for recording.
100% compatibility cannot be guaranteed. This is not an indication of any problems
with your player.
1.) Slide the CD door OPEN switch to the right to unlock
and open the CD door.
OPEN
2.) Place your CD on the center spindle with the printed
label side facing up. Press downward on the disc near
the center hole until the disc is fully seated on the
spindle.
3.) Close the CD door and connect the headphones to the PHONES jack (green
color) by pushing the headphone plug into the PHONES jack until a ‘click’
sound is heard.
4.) Press the PLAY/PAUSE button to begin
playback. The display will briefly show “– –”
flashes while the player reads the disc. The
total tracks and playing time will appear briefly in the display and then the
playback will begin on track 1. The display will show the elapsed playing time
of the track being played.
5.) Adjust the VOLUME control as desired.
12
HD8110_052404.p65
12
25/5/2004, 12:21
6.) Playback will continue until the end of the disc, then the player will stop
automatically and the display will again show the total tracks and playing time
on the disc. After approximately 30 seconds the power switches ‘Off’
automatically to conserve the batteries and the display goes blank. To stop
playback before the disc ends press the STOP button at any time. Press the
STOP button after the disc has stopped to shut the power ‘Off’ completely.
PAUSE CONTROL
To pause momentarily during playback press the
PLAY/PAUSE button again. The elapsed time
display flashes. The sound stops but the disc
continues to spin.
Press the PLAY/PAUSE button once more to cancel Pause mode and resume
normal playback. The elapsed time display stops flashing.
SKIP/SEARCH CONTROLS
Press the SKIP FWD or SKIP REV buttons repeatedly during playback to skip to
higher or lower numbered tracks. Playback will begin on the selected track.
To search within a track at high speed to locate a specific musical passage depress
and hold either the SKIP FWD or SKIP REV controls. The player will search rapidly
forward or backward as long as the buttons are depressed. The volume is
automatically muted during high speed search. Watch the elapsed time display.
When the time display reaches the desired point, release the buttons. Normal
playback will resume at that point and the volume returns to normal level.
13
HD8110_052404.p65
13
25/5/2004, 12:21
MODE BUTTON
Pressing the MODE button during CD playback cycles the player through the
following four special playback modes:
REPEAT 1
REPEAT ALL
INTRO
SHUFF (Shuffle) Playback.
REPEAT PLAYBACK
The player can be programmed to continuously repeat a single track or the entire
disc automatically.
One Track Repeat
During playback press the SKIP FWD or SKIP REV buttons to select the track to
be repeated, then press the MODE button once.
The REPEAT 1 indicator appears in the display
and the selected track will be repeated
continuously.
Press the STOP button to cancel Repeat 1 playback.
All Tracks Repeat
Press the PLAY/PAUSE button to begin playback, then press the MODE button
twice.
The REPEAT ALL indicator will appear in the
display and the entire disc will be repeated
continuously.
Press the STOP button to cancel All Track Repeat playback.
14
HD8110_052404.p65
14
25/5/2004, 12:21
INTRO (Intro Scan) PLAYBACK
The Intro Scan feature plays only the first 10 seconds of each track on the disc.
This feature is useful when you are trying to find a particular song but you cannot
remember the title.
1.) Load your disc in the player as usual and press the PLAY/PAUSE button to
begin playback.
2.) When playback begins press the MODE
button 3 times. The INTRO indicator flashes.
3.) Press the PLAY/PAUSE button once more.
The INTRO indicator stops flashing and
remains ‘On’.
The player backs up to the beginning of track 1, plays the first 10 seconds of
each track on the disc, and then stops.
To cancel Intro Scan playback press the STOP button.
SHUFFLE (Random) PLAYBACK
When Shuffle playback is selected all the tracks on the disc will be played back in
random order.
1.) Load your disc in the player as usual and press the PLAY/PAUSE button to
begin playback.
2.) When playback begins press the MODE
button 4 times. The SHUFF indicator flashes.
3.) Press the PLAY/PAUSE button once more.
The SHUFF indicator stops flashing and
remains ‘On’. The player randomly selects a
track for playback. After each track has
played once the player stops.
To cancel Shuffle playback press the STOP button.
15
HD8110_052404.p65
15
25/5/2004, 12:21
PROGRAMMED PLAYBACK
You can program up to 20 tracks on a disc to play in any desired order.
NOTE: You can program a disc either during Playback or in Stop mode.
1.) Press the MEMORY button once. The
Program Number ‘01’ appears. The PROG
indicator and the the track number ‘00’ flash.
2.) Press the SKIP FWD or SKIP REV button to
select the first track to be programmed.
Example: Track 02.
3.) When the desired track number is flashing
in the display, press the MEMORY button
again to enter the desired track number in
Program Number 01.
The track number returns to “00” and the Program Number advances to “02”.
4.) Repeat Steps 2 and 3 to program additional tracks up to a maximum of 20.
5.) Press the PLAY/PAUSE button to begin
programmed playback. The PROG indicator
remains in the display and the track display
stops flashing.
• Playback begins with the first track you programmed and continues until all
programmed tracks have been played, and then the player stops.
The programmed sequence will remain in the memory until the power shuts
off (approximately 30 seconds) or until the CD door is opened.
• If you press the MEMORY and PLAY/PAUSE buttons again before the power
shuts off, the programmed sequence will play again.
16
HD8110_052404.p65
16
25/5/2004, 12:21
LISTENING TO THE RADIO
1.) Press the RADIO button, the FM radio
frequency appears in the display.
2.) Tune to the desired station by pressing the TUN. UP or TUN. DOWN button.
Each time the button is pressed, the frequency changes.
3.) To search for a station quickly (automatic tuning), keep the TUN. UP or TUN.
DOWN button pressed until the frequency starts to change rapidly then release
the buttons. The tuner will stop on the first strong station. Repeat until you find
the desired station.
4.) If you tune into a FM stereo station, the STEREO indicator will show in the
Display.
If the FM reception is noisy, press the MODE button to change to Mono mode.
The MONO indicator appears in the display.
5.) Adjust the VOLUME control to your listening preference.
6.) To turn off the radio, press STOP button to shut power ‘Off’.
Antenna Information
The stereo headphone cable serves as the FM antenna when listening to FM
stations. Make sure that the headphone cable is unwound completely in order to
provide the best reception.
17
HD8110_052404.p65
17
25/5/2004, 12:21
PRESETTING STATIONS IN MEMORY
Up to 20 FM stations can be stored into the Preset memories. They will remain in
memory as long as the batteries are installed.
1.) Press the RADIO button to turn the radion ‘On’.
2.) Press the TUN. UP or TUN. DOWN button to tune a station.
3.) Press the MEMORY button – the display
blinks.
4.) While the the display is blinking, press the
PRESET button to select the Preset channel
to store. Example: 04.
5.) Press the MEMORY button again to store that
station into Preset number 04.
6.) Repeat steps 2-5 selecting a different preset channel number each time to
store up to 20 preset channels.
TO RECALL PRESET STATIONS
1.) Press the RADIO button to turn the radion ‘On’.
2.) Press the PRESET button to select the preset station as desired.
3.) To change a preset station, enter a new station into the memory you wish to
change. The previously memorized station is replaced by the new station.
18
HD8110_052404.p65
18
25/5/2004, 12:21
CARE AND MAINTENANCE
CLEANING THE CABINET
Wipe with a soft cloth. If the cabinet is very dirty, dampen the cloth with a weak
solution of neutral detergent and water, and then wipe clean.
CLEANING THE LENS
A dirty lens will cause sound skipping and, if the lens is very dirty, the CD may not
work. Open the disc cover and clean the lens as follows:
DUST OR DRY PARTICLES
Using a camera lens brush/blower, blow on the lens
several times, then wipe it lightly with the brush to remove
dust. Then, blow on the lens once more.
FINGERPRINTS
To remove fingerprints from the lens, use a cotton swab
starting in the middle and working to the outside edge.
Use only very light pressure on the lens to avoid forcing
it out of alignment.
CLEANING THE DISC
When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the
center out.
NOTE:
Do not use solvents such as benzine, thinner, commercially available cleaners or
anti-static spray intended for analog discs.
19
HD8110_052404.p65
19
25/5/2004, 12:21
LIMITED WARRANTY
Emerson Radio Corp. warrants manufacturing defects in original material, including
original parts and workmanship, under normal use and conditions, for a period of
ninety (90) days from the date of original purchase in the U.S. With your dated
proof of purchase, we will provide repair service at no charge for labor and parts
at an authorized Depot Repair Facility, or replace the product in our discretion.
For repair or replacement, pack your unit in a padded box, enclose your check or
money order payable to Emerson Radio Corp. in the amount of $9.00 (not required
by California residents) to cover shipping and handling costs, and enclose a copy
of your proof of purchase. Send your unit to:
Emerson Radio Corp.
1901 Diplomat Drive.
Farmers Branch, TX 75234.
This warranty does not cover damage from negligence, misuse, abuse, accident,
failure to follow operating instructions, commercial use, rental, repairs by an
unauthorized facility, or products purchased, used, serviced or damaged outside
of the United States.
THIS WARRANTYGIVES YOU SPECIFIC LEGAL RIGHTS, ANDYOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
AU898M
SERVICE
FOR ADDITIONAL SET-UP OR OPERATINGASSISTANCE
PLEASE CALL:
1-800-898-9020
FOR CUSTOMER SERVICE, PLEASE WRITE TO:
Emerson Radio Corp.
Consumer Affairs Dept.
1901 Diplomat Drive,
Farmers Branch, TX 75234.
20
HD8110_052404.p65
20
25/5/2004, 12:21
EMERSON
Part No. 16-2937
405-01
Printed in China
HD8110_052404.p65
21
25/5/2004, 12:21
|