Инструкция для
Delonghi EC 152 CD
ꢀꢁдꢊꢁбнꢈяꢄинфꢁꢊмꢈцияꢄꢁꢄтꢁвꢈꢊꢃ,
ꢁтзывы,ꢄꢁбзꢁꢊыꢄиꢄꢈꢇꢆꢃꢆꢆꢂꢈꢊы
ꢀꢁлꢂчитꢃꢄтꢃꢅничꢃꢆꢇꢂюꢄꢇꢁнꢆꢂльтꢈцию.
ꢉꢊꢂглꢁꢆꢂтꢁчнꢁ.ꢄБꢃзꢄвыꢅꢁдныꢅ
COFFEE MAKER
Instruction for use
Please retain instructions for
future reference
EC152.CD
Electrical requirements
Before using this appliance ensure that the voltage indicated on the product corresponds
with the main voltage in your home, if you are in any doubt about your supply contact your
local electricity company.
The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13
amp capacity.
Should this plug not fit the socket outlets in your home, it should be cut off and replaced with
a suitable plug, following the procedure outlined below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly
disposed of and not left where children might find it and plug it into a supply socket - with
the obvious consequent danger.
Please note: We recommend the use of good quality plugs and wall sockets that can be
switched off when the machine is not in use.
IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance
Green and Yellow to Earth
with the following code:
13 amp
Fuse
GREEN AND YELLOW
BLUE
BROWN
EARTH
NEUTRAL
LIVE
Brown to
live
Blue to
neutral
Cord Clamp
As the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
-
-
-
The wire which is coloured green and yellow must be connected to the terminal in the plug which is
marked with the letter E or by the earth symbol or coloured green or green and yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L
or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal.
Do not forget to tighten the mains lead clamp on the plug. If your electricity supply point has
only two pin socket outlets, or if you are in doubt, consult a qualified electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried
out by a qualified electrician and should only be replaced with a flexible cord of the same
size.
After replacement of a fuse in the plug, the fuse cover must be refitted. If the fuse cover
is lost, the plug must not be used until a replacement cover is obtained. The colour of the
correct replacement fuse cover is that of the coloured insert in the base of the fuse recess or
elsewhere on the plug. Always state this colour when ordering a replacement fuse cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362 should be fitted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio inter-
ference.
Warning - this appliance must be earthed
2
Description
OFF
position
OK indicator light
Steam
position
On indicator
light
Cofee- hot water
delivery position
Water tank
Water tank lid
Steam
dial
Filter compartment
Power supply cable
Cofee
tamper
Selector dial
Steam or
hot water tube
Drip tray
Cappuccino nozzle
Boiler outlet
Filter
Filter holder
Measure
3
ig. 3
ig. 2
ig. 1
1
2
ig. 5
ig. 6
ig. 4
ig. 8
ig. 9
ig. 7
4
ig. 15
ig. 14
ig. 13
ig. 17
ig. 18
ig. 16
ig. 20
ig. 21
ig. 19
ig. 22
ig. 23
ig. 24
ig. 25
5
Safety
Symbols used in these instructions
The important recommendations have these symbols. These
recommendations must be followed.
to the enclosed guarantee lealet for details.
Attention:
Keep the packaging material (plastic bags, expanded
polystyrene) out of the reach of children.
Danger!
Failure to comply can be or is the cause of injury due to
life-threatening electric shocks.
Attention:
The appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
Attention!
Failure to comply can be or is the cause of injury or
damage to the appliance.
Scalding hazard!
Failure to comply can be or is the cause of scalding or
burns.
Scalding hazard!
This appliance produces hot water and steam may form
when it is operating.
Please Note:
This symbol highlights recommendations and important
information for the user.
Pay attention not to come into contact with hot water
sprays or steam.
Fundamental recommendations regarding safety
Do not touch the cup warmer plate when the appliance
is on; it is hot.
Danger!
As the appliance operates using electric current, electric
shocks can not be excluded.
Conditions of use
This appliance is manufactured for the preparation of
cofee and to heat beverages.
Therefore, follow the safety recommendations given:
•
Do not touch the appliance when you have wet
hands or feet.
The appliance is designed and produced for domestic use
only. It is not suitable for use in:
•
•
Do not touch the plug with wet hands.
Make sure that the socket used can always be easily
reached, so that the plug can be removed when
required.
•
•
•
•
staf kitchens in shops, oices and other workplaces
farms
hotels, motels or other holiday accommodation
guest houses
•
Remove the plug from the socket by acting directly
on the plug itself. Do not pull the cable as damage
could be caused.
Any other use must be considered improper and therefore
dangerous.
•
•
Remove the plug from the socket to disconnect the
appliance completely.
The manufacturer is not liable for damage deriving from
the improper use of the appliance.
Do not attempt to repair the appliance if it should
breakdown.
Switch the appliance of, remove the plug from the
socket and contact the After-Sales Service. Please
refer to enclosed guarantee lealet for details.
Iftheplugorpowersupplycablearedamaged,have
them replaced exclusively by the De’Longhi After-
Sales Service, in order to prevent risks. Please refer
•
6
Introduction
Instructions for use
Only connect the appliance to a correctly installed socket
with a minimum rating of 10A and correctly earthed.
In the case of incompatibility between the socket and
the plug on the appliance, have the plug replaced by a
qualiied technician.
Thank you for choosing this cofee machine. To get the
very best out of your new cofee machine it is advisable
to read these instructions before using the appliance.
This is the only way to ensure optimum results and ma-
ximum safety.
•
The power supply cable on this appliance must
never be replaced by the user as special tools are
needed for this operation. Contact an After-Sales
Centre authorised by the manufacturer if the cable
is damaged or must be replaced, in order to avoid all
risks. Please refer to enclosed guarantee lealet for
details.
The manufacturer is not liable for damage deriving from
the failure to comply with the user instructions.
Please Note:
Keep these instructions carefully. If the appliance should
be transferred to other persons, these instructions must
accompany it.
Filling the water tank
1. Open the water tank lid (ig. 1) and then lift the tank
to remove it (ig. 2).
Check after transport
After the packaging has been removed, check the
integrity of the appliance and the presence of all
accessories.
2. Fill the tank with fresh water but do not pass MAX
level (ig. 3). Re-position the tank by pressing it
lightly in a way to open the valve situated on the
base of the tank itself.
Do not use the appliance in the presence of obvious
damage. Contact the De’Longhi Customer Services
department, please see enclosed lealet.
3. Alternatively, do not remove the tank, just ill it by
pouring in water from a jug, be careful of splashes
Installing the appliance
Attention!
The following safety measures must be complied with
when installing the appliance:
Attention!
Do not operate the appliance without water in the tank
and always ill it when the water is a few centimetres
from the bottom.
•
•
•
Theappliancecouldbedamagedbythepenetration
of water.
Please Note: it is normal to ind water in the
compartment under the tank; dry using a clean sponge.
Do not position the appliance near to water taps or
sinks.
The appliance could be damaged if the water it
contains freezes. Do not install the appliance in a
room where the temperature can fall below freezing
point.
Position the power supply cable in a way that it
cannot be damaged by sharp edges or by contact
with hot surfaces.
Connecting the appliance
Attention!
Make sure that the electric mains voltage corresponds
with that indicated on the rating plate on the base of the
appliance.
7
Making espresso
Making espresso
Please Note: irst use
cofee can run out slowly. If you press too lightly, the
cofee can run out too fast.
3. Remove any excess cofee from the rim of the ilter-
holder and attach it to the machine: turning it fully
home to the right (ig. 5) to prevent water from
escaping.
Before using the appliance for the irst time, rinse the
internal piping thoroughly, operating it as you would
to make cofee, until two tanks of water have emptied,
then proceed with making cofee.
4. Position the cup or cups under the ilter-holder
spouts (ig. 11). It is recommended to warm the
cups before making the cofee by running them
under hot water.
Pre-heating the cofee machine
1. Turn the appliance on by rotating the selector dial
to the
position (the relative indicator light
switches on) (ig. 4) and attach the ilter-holder
with the empty ilter to the machine (ig. 5). Make
sure that the ilter holder is correctly inserted into
the relative seat (ig. 6).
5. Make sure that the OK light (ig. 7) is on (if it is of,
wait for it to switch on) and turn the selector dial to
the
of cofee has been obtained, interrupt delivery by
rotating the selector dial back to the position
position (ig. 8). Once the desired amount
2. Place a cup under the ilter-holder. Use the same
cup in which the cofee is to be served so that it can
be pre-heated.
(ig. 7). (It is recommended not to run the cofee for
more than 45 seconds).
3. Wait until the OK light comes on (ig. 7) then
immediately rotate the selector dial to the
position (ig. 8), allow the water to run until the OK
light switches of , then stop the water by rotating
the selector dial back to the position (ig. 4) and
empty the cup.
6. Turn the ilter holder from right to left to release the
ilter-holder.
Scalding hazard!
To prevent sprays, do not release the ilter-holder while
the machine is dispensing cofee.
(It is normal for a small, harmless puf of steam to be
released when the ilter-holder is removed).
7. To remove the used cofee, lock the ilter using
the lever in the grip and let the cofee fall out by
knocking the over-turned ilter-holder (ig. 12).
8. To turn the appliance of, rotate the selector dial to
the “ ”position.
Making and espresso using ground cofee
1. To prepare one cofee, ill the ilter with a level
measuring spoon of ground cofee, about 7gr. (ig.
9). If you wish to prepare two cups of cofee, ill the
ilter with two less-than-level measuring spoons
of ground cofee (about 7+7 gr). Fill the ilter
with small amounts at a time to prevent the cofee
spilling out.
Attention:
For correct use, before illing the ilter with ground cofee
always make sure there is no residual cofee in the ilter
from the previous infusion.
2. Distribute the ground cofee evenly and press it
lightly using the cofee tamper (ig. 10).
Pressing the ground cofee is very important to
obtain a good espresso. If you press too hard, the
8
Cappuccino
To switch of the appliance, turn the selector dial to
the position.
Making a cappuccino
1. Prepare the espresso cofee as described in the
previous paragraphs, using cups that are large
enough
9. Pour the frothed milk into the cups containing the
previously prepared espresso cofee. The cappuccino
is ready. Add sugar and sprinkle a little powder
chocolate on top of the froth if desired.
2. Rotate the selector dial to the position (ig. 13).
3. While waiting for the OK light, ill a container with
about 100 grams of milk for every cappuccino
to be prepared. The milk must be at refrigerator
temperature (5°C). When choosing the container
consider that the volume of the milk will increase by
2 or 3 times.
Please Note:
•
•
If more than one cappuccino is to be prepared, irst
make all of the cofees and then prepare the milk for
all of the cappuccinos;
If more cofee must be prepared after the
milk has been frothed, allow the boiler to
cool irst otherwise the cofee may be burned.
To cool it, position a container under the ilter-holder
spouts, turn the selector dial to the position (ig.
8); allow water to run out until the steam function
light switches of; turn the selector dial to the
position and prepare cofee as illustrated before.
Maximum steam delivery of 60 seconds is
recommended and the milk must not be frothed
more than 3 times consecutively.
Please Note:
It is recommended to use semi-skimmed milk at
refrigerator temperature.
4. Position the container with the milk under the
cappuccino nozzle.
5. Wait for the OK light to switch on. This indicates
that the boiler has reached the ideal temperature
for steam production, when reaching the ideal
temperature, it is normal for a small puf of steam
and water to be released, and collected in the drip
tray.
•
Cleaning the Cappuccino nozzle
6. Extract the cappuccino nozzle by pulling it and
rotating it towards the left (ig. 14): pay attention
not to touch the boiler outlet because it is hot.
Position the container with the milk under the
cappuccino nozzle.
The cappuccino nozzle must always be washed after
each use to ensure hygiene. Proceed as follows:
1. Discharge a small amount of steam for a few seconds
(see points 2,5 and 6 of the previous paragraph) by
turning the steam dial (ig. 16). By doing this, the
cappuccino nozzle clears any milk left inside. Switch
the appliance of by turning the selector dial in
position.
7. Dip the cappuccino nozzle into the milk a few
millimeters (ig. 15). Turn the steam dial anti-
clockwise (ig. 16), for at least half a turn. Steam
escapes from the cappuccino nozzle giving the milk
a creamy appearance and increasing its volume. To
obtain a creamier froth, dip the cappuccino nozzle
into the milk and turn the container with slow
movements from the bottom upwards.
2. Use one hand to hold the cappuccino tube and the
other to release the cappuccino nozzle by turning it
clockwise (ig. 19).
3. Wash the cappuccino nozzle thoroughly in warm
water.
8. When the volume of the milk has doubled, dip the
cappuccino nozzle deep down and continue to heat
the milk (ig. 17). When the desired temperature
(ideal value is 60°C) and the desired milk froth have
been reached, interrupt the steam by turning the
steam dial clockwise (ig. 18) and turn the selector
dial to the position.
4. Makesurethattheholesindicatedbythearrows(ig.
20) are not blocked. Clean using a pin if necessary.
5. Re-mount the steam maker by inserting it irmly
upwards into the steam tube.
6. Re-mount the cappuccino nozzle by inserting it
upwards and turning it anti-clockwise.
9
Hot water • Cleaning
Producing hot water
ilter (ig. 25), making sure that the pin is inserted
into the hole of the support itself (see arrow ig.
25).
1. Switch the machine on by turning the selector dial
to the position (the relative light comes on) (ig.
4). Wait for the OK light to switch on (ig. 7).
2. Position a container under the cappuccino nozzle.
3. When the OK light comes on, turn the selector dial
•
Finally, tighten the tap.
The warranty is not valid if the cleaning operations
described above are not performed on a regular basis.
to the
position (ig. 8) and turn the steam dial
Cleaning the boiler outlet
About every 300 cofees the espresso boiler outlet must
be cleaned as follows:
anti-clockwise at the same time (ig. 16). The hot
water will be delivered from the cappuccino nozzle.
4. To interrupt the hot water, turn the steam dial
clockwise and turn the selector dial to the
position.
•
Make sure that the cofee machine is not hot and
the plug is disconnected from the socket;
Use a screwdriver to remove the screw that ixes the
espresso boiler outlet (ig. 26);
•
Maximum delivery of 60 seconds is recommended.
•
•
•
Remove the boiler outlet;
Clean the boiler using a damp cloth;
Cleaning
Danger!
During cleaning, never immerse the cofee machine
in water. It is an electrical appliance.
Clean the outlet thoroughly using hot water and a
brush. Check that the holes are not blocked. If this is
not the case, clean them using a pin (ig. 23).
Re-mount the boiler outlet, paying attention to
position it correctly on the gasket.
•
•
Before performing any cleaning operations on the
external parts of the appliance, switch the machine
of, remove the plug from the socket and let the
machine cool down.
•
The warranty is not valid if the cleaning operations
described above are not performed on a regular basis.
Cleaning and maintenance of the ilter
Other cleaning operations
1. Do not use solvents or abrasive detergents to clean
the machine. Use a soft, damp cloth.
Clean the ilter-holder and ground cofee ilter about
every 300 cofees or if the cofee drips through the ilter-
holder and does not low unrestricted:
2. Clean the ilter-holder cup, the ilters, drip tray and
water tank regularly.
•
•
Remove the ilter from the ilter-holder.
Unscrew the ilter cap (ig. 21) in the direction
indicated by the arrow on the cap itself.
To empty the drip tray, remove the cup warmer grid,
remove the water and clean the tray using a cloth:
then re-assemble the drip tray.
•
Slide the cream enhancer device from the container
by pushing it from the cap end.
Remove the gasket.
Rinse all components and clean the metal ilter
thoroughly using hot water and a brush (ig. 22).
Check that the holes in the metal ilter are not
blocked. If this is not the case, clean them using a
pin (see ig. 23) or when descaling.
Clean the water tank using a soft bottle-brush in
order to reach the bottom.
•
•
Danger!
During cleaning, never immerse the machine in water: it
is an electric appliance.
•
•
Re-mount the ilter and the gasket on the plastic
disc as indicated in (ig. 24). Make sure that the
plastic disc pin is inserted inside the hole in the
gasket as indicated by the arrow in (ig. 24).
Re-insert the unit into the steel container for the
10
Descaling · Disposal
which it is made in order to make signiicant savings in energy
and resources.
Descaling
It is recommended to descale the machine about every
200 cofees.
Follow this procedure:
The product has the crossed-out wheeled bin mark as a
reminder of the obligation to dispose of household appliances
separately.
1. Fill the tank with the descaling solution obtained
by diluting the descaler with water following the
indications given on the pack.
The appliance is in compliance with the following
CE Directives:
2. Switch the appliance on by turning the selector to
the position and wait until the OK indicator light
comes on.
•
•
•
“LowvoltageDirective”2006/95/CEandsuc¬cessive
amendments.
“EMC Directive” EMC 2004/108/CE and suc¬cessive
amendments.
3. Make sure that the ilter holder is not attached and
position a suitable container under the machine
outlet.
The materials and objects destined to come into
contact with food stufs are in compliance with the
provisions of the 1935/2004 European Standard.
4. Rotate the selector dial to the
position and
allow about 1/4 of the solution contained in the
tank low out. Every now and again turn the steam
dial and allow a small amount of solution to escape;
then interrupt by turning the selector dial to the
position then interrupt by pressing the button again
and leave the solution to act for about 5 minutes.
5. Repeat point 4 another 3 times or until the tank is
completely empty.
Technical date
Mains voltage:
Absorbed power:
Dimensions (LxHxD ):
Pressure:
220-240V 50/60Hz
1100W
195x285x240 (330) mm
˜
15 bar
1 L
Water tank capacity:
Cable lenght:
Weight:
1,2 m
3 kg
6. To eliminate residues of the descaling solution, rinse
the tank well and ill it with clean water (without
descaler).
7. Rotate the selector dial to the
position and
operate the appliance until the tank is completely
empty.
8. Repeat operations 6 and 7 again.
Repairs to the cofee machine relative to lime scale
problems are not covered by the warranty if the descaling
procedure is not performed on a regular basis.
Disposal
Recommendations for the correct disposal of
the product in compliance with the 2002/96/CE
European Directive.
The product must not be disposed of as urban waste at the end
of its working life.
It must be taken to appropriate local authority separate waste
collection centres or to dealers providing this service.
Disposing of a household appliance separately avoids possible
negativeconsequencesfortheenvironmentandhealthderiving
from unsuitable disposal and allows to recover the materials of
11
Troubleshooting
Problem
Possible causes
Solution
No water in the tank
Fill the water tank
Espresso cofee does not low out
The holes in the ilter-holder are blocked
Clean the holes in the ilter-holder spouts
The espresso boiler outlet is blocked
Clean as indicated in the “Cleaning the boiler outlet”
paragraph
The ilter-holder is inserted incorrectly
Attach the ilter-holder correctly and turn it fully
to the right
Espresso cofee drips from the edges of
the ilter-holder instead of through the
holes
The espresso boiler gasket has lost elasticity
The holes in the ilter-holder spout are blocked
Replace the espresso boiler gasket: contact Customer
Services
Clean the holes in the spouts.
The espresso OK light is not on when the cofee
button is pressed
Wait for the OK light to switch on
The espresso cofee is cold
Pre-heating has not been carried out
The cups have not been pre-heated
Pre-heat as indicated in the paragraph
Pre-heat the cups using hot water or leaving them
for at least 20 minutes on the cup warmer plate
on the lid
The water tank is empty
Fill the water tank
Loud pump noise
The tank is inserted incorrectly and the valve on the
bottom is not open
Press the tank lightly to open the valve on the
bottom
The ground cofee has not been suiciently pressed
Not enough ground cofee
Tamper the ground cofee more (ig. 10)
The cofee cream is light (cofee lows
quickly from the spout)
Increase the amount of ground cofee
The cofee is not ground inely enough
Only use cofee ground speciically for espresso
cofee machines
Incorrect type of ground cofee
The ground cofee is too tightly pressed
Too much ground cofee
Change the quality of the ground cofee
Decrease the amount of ground cofee
Reduce the quantity of ground cofee
Clean as indicated in “Cleaning the ilter”
The cofee cream is dark (the cofee
lows slowly from the spout)
The espresso boiler outlet is blocked
The ilter is blocked
Only use cofee ground speciically for espresso cofee
machines and it must not be damp
The cofee is too inely ground
The ground cofee is too ine or is damp
Incorrect type of ground cofee
Milk not cold enough
Change the quality of the ground cofee powder
Only use cofee ground speciically for espresso cofee
machines and it must not be damp
Change the quality of the ground cofee powder
Always use milk at refrigerator temperature
The milk does not froth when making a
cappuccino
Cappucccino maker is dirty
Carefully clean the holes in the cappuccino nozzle, in
particular, those indicated in igure 20
12
|