ION-16 DIGITAL CLOCK
Wiring:
RED
ORANGE
BLUE
-
-
-
-
connect to fused, switched 12 volt power. (An accessory terminal will work for this.)
connect to fused, constant battery power.
Night Dimming: connect to the head light switch.
connect to a main ground location
BLACK
Mounting:
The gauge requires an oval hole 1-7/16” high x 3-1/16” wide. It should be inserted into the opening from
the front and the 2 L-clamps will be installed from the back. Tighten a nut on each of the L-clamps so that the
gauge is secure. Gauge depth to the back of the case is 1”. Gauge depth including the mounting studs is 1-7/8”.
Operation:
The gauge needs the red, orange, and black wires connected to operate. The red wire should have
switched 12 volt power from an ACC. point on the fuse panel. The orange wire should have constant 12 volt
power. The black wire should be connected to a good ground point. When the blue wire has 12 volts, it will dim
the display for night viewing.
Setting the time:
Using a small, thin object such as a toothpick or pin, press “set” buttons through front lens access holes.
The access holes are on the left and right sides of the lens. Left “set” button advances hours, right “set” button
advances minutes. Each time that you make a change to either the hours or minutes, the seconds are reset to
zero.
Adjusting the accuracy:
The clock is accurate to +/-2 minutes a month as it is sent. It can be tuned for better accuracy if desired.
Press and hold both of the set buttons for several seconds. The clock will display “C 0”. The “C” indicates that it is
in the calibration mode and the second number is the current calibration value. The calibration value indicates the
number of seconds to add or subtract each day. The clock can be adjusted from +7 sec/day to -7 sec/day.
Press the minute set button to change the cal value. Press the hour set button to return to normal clock operation.
MAN# 650142
SERVICE AND REPAIR
DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical consultation
is available to help you work through any questions or problems you may be having installing one of our units.
Should you ever need to send the unit back for repairs, please package the product in a good quality box
along with plenty of packing material. Ship the product by UPS or insured Parcel Post. Be sure to include a
complete description of the problem, your full name and address (street address preferred), and a telephone
number where you can be reached during the day. An authorization number for products being returned for repair
is not needed. Any returns for warranty work must include a copy of the dated invoice or bill of sale.
Technical specifications
Minimum operating voltage
Maximum operating voltage
-
-
7 volts
17 volts
(operating at or near maximum voltage for an extended time can damage unit)
Clock accuracy
Typical current draw (@ 13.8V) -
Standby current draw (key off)
-
±2 minute per month
0.13 A
0.005 A
-
ION SERIES DIGITAL GAUGE LIMITED WARRANTY
DAKOTA DIGITAL (the Company) warrants to the ORIGINAL PURCHASER of this product that should it, under normal use and
condition, be proven defective in material or workmanship within 24 MONTHS FROM THE DATE OF PURCHASE, such defect(s) will be
repaired or replaced (at the Company’s option) without charge for parts or labor directly related to repairs of the defect(s).
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g.
dated bill of sale), name, address, phone number, and specification of defects, transportation prepaid, to the factory. This Warranty is valid for
the original purchaser only and may not be transferred.
This warranty does not cover nor extend to damage to vehicle electrical system. This Warranty does not apply to any product or part
thereof which in the opinion of the Company has been damaged through alteration, improper installation, mishandling, misuse, neglect, or
accident.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABLITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR
BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABLITY MUST BE BROUGHT WITHIN
A PERIOD OF 24 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED,
WHATSOEVER. No person or representative is authorized to assume for the Company any liability other that expressed herein in connection
with the sale of this product.
The Company does not warrant that this product cannot be compromised or circumvented. THE EXTENT OF THE COMPANY’S
LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL
THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID TO THE PURCHASER FOR THE PRODUCT.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation if incidental or consequential
damage so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
4510 W. 61ST St. N., Sioux Falls, SD 57107
Phone: (605) 332-6513 FAX: (605) 339-4106
©Copyright 2004 Dakota Digital Inc.
MAN# 650142
|